I have set up qmailtoaster as a gateway for exchange.
my smtproutes contain this:
thedomain.com:mail.exchange.com
and my rcpthosts contain:
thedomain
The problem I am facing now is, the exchange was able to send mails through me alright. But when mails come in, qmailtoaster is suppose to forward the mails to the exchange server but it is not, rather the mails are sitting in the toaster's queue.
I have ticket tracking software that mails ticket to groups. Right now the software is on an exchange server. After moving it to a dedicated linux server (debian lenny) I cant get it to email any of the internal domain addresses. I have tried to setup sendmail to relay it to the exchange server. Logs indicate that it was sent by the ticket tracking software but the message never hits the mailbox. It also wont get to any other mail address. Is there a better way to do this? The crm software will utilize either a smtp server or any mail server on the localhost. The problem is that with the dedicated server on the same network as the exchange server, it fails to send the mail even if I assign an external smtp server. But if the dedicated server is on a different network then it works using any smtp server in its configuration. I need something that can "pass the email" to the exchange server. Or just be able to send the mail to internal email account and still be on the same network.
View 2 Replies View RelatedHow to seup nagios to send email to mails in MS Exchange server ?
View 3 Replies View Relatedhow to setup sendmail ( Centos 5.2 ) as mail relay for Microsoft exchange. I will put the mail relay in DMZ and Mail server in Local Network.
View 3 Replies View RelatedI've just setup qmailtoaster for mailbox server. The system looks like good. I can send/receive email in internal. But when I send email by outlook to external, the system appears the following errors: "'553 sorry, that domain isn't in my list of allowed rcpthosts (#5.5.3 - chkuser)'". I've tried to setup "My Server requires authentication" in Outlook Express to authenticate before sending outgoing mail, but not successful. The system has the same error.
View 3 Replies View Relatedsetup 2 gateway in my email server(opensuse).
now i wan to setup 2 internet lines for my email server, which mean that either one of the line is down, i still can receive mail from another line.
Example
Internet line 1 = ISP1
Internet line 2 = ISP2
my email server got 3 nic which...
eth0 = 192.168.1.2 (255.255.255.0) (from ISP1 GW 192.168.1.1)
eth1 = 192.168.2.2 (255.255.255.0) (from ISP2 GW 192.168..2.1)
eth2 = 168.168.1.2 (255.255.0.0) (connect to local LAN)
now existing GW set on the server is 192.168.1.1, mail receive and send through ISP1. now we wish to set somethings that once the ISP1 line is down, the server will auto switch to ISP2 gateway and continue send and receive mail without manually change of settings
I have been searching google for a while now and have not found exactly what I am looking for. I would like to use my fresh install of ubuntu server 11.04 as my router/gateway for my home. I am not an expert at linux by any means but I can usually figure stuff out. I believe I need iptables, bind, and a few others probally. It eventually will also be a samba server but I have done a little with samba before. I do have 2 network cards, my router at the moment is starting to die and would love to have a more powerful router. I would also like to figure out how to do port forwarding in the router, as well as be able to see the load on the network cards. Maybe there is a program to show usage by user? As well as be able to do packet pritorization.
View 4 Replies View RelatedI use web-browser and and url to get my mail from company's mail server.
Code:
[URL]
Can I configure evolution to fetch my mail?
I have (adsl router "rebotic") and we are 3 nodes sharing Internet the question is: want make network (exchange files) between me (ubuntu os) and one of my internet members ,and I don't know how can I set up network between us in ubuntu.
View 1 Replies View RelatedWould like to start using a setup similar to exchange for emails but on Ubuntu - does anyone have any reccs? Something pretty easy to setup, user friendly, have a caleneder etc.
View 2 Replies View RelatedI've been trying to setup an IPSec connection between two routers, but am having trouble with the actual packet routing.
My setup currently is two local networks (192.168.1.0/24[netLANA] and 192.168.0.0/24[netLANB]) that are connected to their own routers (192.168.1.1 and 192.168.0.1 respectively). The routers are both connected to the 194.26.1.0/24[netWAN] network. I wish to setup an IPSec connection between the two routers, to act in tunnel mode between the two local networks.
The first router is a linux box (on the netLANA network) that I am setting up using the ipsec-tools, and the other is a Netgear ProSafe FVS318G (on the netLANB). I've set them both up to have the same configuration for IPSec. Also, on the linux router I have setup a route like this:
Code:
$ route add -net 192.168.1.0/24 wlan0
So that all traffic destined for the netLANB network will be routed to the wlan0 interface (netWAN in this case, and therefore over the tunnel).
My problem is that if I ping from any host on netLANA, I can see the ICMP reply comes back to the linux router, but it doesn't get back to the original host.
From the linux router, here is the tcpdump of the ping:
Code:
$ tcpdump -n -S -i any
17:06:26.308353 IP 192.168.0.5 > 192.168.1.4: ICMP echo request, id 1036, seq 1, length 64
17:06:26.308780 IP 194.16.1.6 > 194.16.1.5: ESP(spi=0x0ea08914,seq=0x2f), length 116
17:06:26.316287 IP 194.16.1.5 > 194.16.1.6: ESP(spi=0x0be1036c,seq=0x2f), length 116
17:06:26.316287 IP 192.168.1.4 > 192.168.0.5: ICMP echo reply, id 1036, seq 1, length 64
[Code]....
I have setup a second machine with slackware 13.37, it is a "supermicro" which I picked up though my work. the idea was to set it up as a gateway and gradually expand my knowledge of sub networking, iptables, forwarding and the like. after a couple nights of forum searching and "o'reilly" book reading I am still unable to get a proper route working thru the "supermicro" to our dsl router.
What is setup?: I will start from my main machine simply calling it slackbox
slackbox: has two ethernet cards which i have given static ip's to
eth0 192.168.2.16 and eth1 192.168.3.11
eth0 (192.168.2.16) is connected to a switch and then to our dsl router, it is working, I am using right now to work on this forum.
eth1 (192.168.3.11) is connected to the "supermicro" thru a cross-over cable, it also is working, pinging the "supermicro" works.
default gateway on slackbox is set to be 192.168.3.10 (the supermicro)
I only set slackbox's default as 192.168.3.10 when testing to see if the supermicro gateway will work
supermicro: also has two ethernet cards which i have given static ip's to
eth0 192.168.3.10 (this is the card with the cross-over cable connected)
pinging 192.168.3.11 (the slackbox) works.
eth1 192.168.2.24 is connected to our switch as well, it is working, pinging our dsl router works.
default gateway on supermicro is set in rc.inet.conf to be 192.168.2.1 (which is our dsl router)
All my machines have two ethernet cards. This has just made it easy for me to test the setup while still having internet access on slackbox. Yet when testing the gateway from slackbox thru supermicro I am getting "Destination Host Unreachable".
I have a temporary system up with wlan0 and eth2.
I want the eth0 address to be the gateway for accessing the internet on wlan0.
How do I setup static routes?
I'm not too keen with networking...
Code:
After editing my network connections gateway setup as 192.168.1.1 I get back 0.0.0.0 after I run nm-tool. I'm using Ubuntu ver 9.04 setup on my VMware server.
View 1 Replies View RelatedI have 1 root-server with 2 NICs, both having their own internet IP addresses:
Code: eth0 = 8x.x.x.183
eth2 = 8x.x.x.205 We only have one gateway on that network:
Code: gateway = 8x.x.x.1 We want to use eth2 for postfix + http, and eth0 for all the other stuff.
How can this be setup ? With route / ip route / iptables ?
i need to configure postfix on centos to relay email from the internet to the Exchange Server and i also need that emails sent from the exchange within the same domain be sent to postfix then resent to exchange because i have spamassassin and clamav installed on centos to filter all incoming and outgoing mails ...
View 1 Replies View RelatedI'm trying to setup routes for a gateway that resides on a different subnet. Our ISP leased us a block of IPs and told us to route through the current gateway, which is on a different subnet than our current block of addresses. To test, I've enabled one of the new addresses on one of the existing machines, which works. That machine has an address on the same subnet as the gateway, however.
The gateway address is 24.111.1.177 One of the new addresses I'm trying to use is 96.2.192.130, netmask= 255.255.255.240, broadcast= 96.2.192.143 Obviously, I can't just specify that gateway in /etc/network/interfaces without some routing, which is where the trouble I'm having is. The machine I'm trying to set this up on is part of 2 networks - one internal, on two different NICs.
[Code]...
I recently had the need to relay SMTP mail through our organizations hosted MS Exchange server. I had to do a little troubleshooting, so I wrote a concise summary of the procedure I followed.
View 1 Replies View Relatedi had redhat version 5 server , i want use it as BTSN exchange can i used for this, and how
View 1 Replies View RelatedHave read a whole bunch of threads from how and troubleshooting but still having problems.Was thrown a box configured by someone who resigned today. Need to get mail from the box outbound via SMTP relay off our exchange server.
View 4 Replies View RelatedI've set up a Lan-to-Lan (routed) OpenVPN tunnel. For redundancy I want to set up a second VPN tunnel on a fallback gateway/firewall on the client side. Currently, both sides (server/client) know how to route packets across each others physical LAN. So no NAT is used. When the primary gateway (fw1) is connected to the VPN server all traffic runs via the fw1 tunnel. Than when the secondary gateway (fw2) connects to the VPN server and fw1 is still connected all traffic for fw1 will be delivered to fw2 and effectively destroying traffic intended for fw1. This is of course no problem if I first shutdown (fence) fw1, than set up fw2 to use the gateway IP address from fw1 and set up the VPN tunnel to the VPN server. Effectively replacing fw1 with fw2 on the client side.
However, I can't seem to find a decent howto.
I am also exploring the possibility to let both tunnels active and let OpenVPN (or another tool) decide how to route packets back and forth the different LANs. A virtual IP between two gateway's both running a VPN or something similar. This would be the preferred method of course. However, I don't know how to tackle this one but I'm pretty sure there are people out there who are happy to share their 2 cents.
I have 17 system (sys1,sys2,sys3.....sys17) in my office, and i am willing to setup a dedicated system to act as a firewall for that i have selected sys1 with two NIC(eth0 for local network and eth1 for internet) and i have configured to access internet in my office for that i have opened a wellknown port 80.but my clients are not accessing the internet..
and please check my sample IP configuration !!!
interface : eth1 (ISP IP)just for example
IP :192.168.0.2
gateway:192.168.0.1
dns:202.56.230.5
dns:202.56.230.6
Interface : eth0 (my local lan )
192.168.1.1
255.255.255.0
IP address of xp clients ranges form 192.168.1.2 to 192.168.1.16 with default 255.255.255.0
my question is that which gateway address and dns i have to give to my clients for accessing internet ?...
I have set up ubuntu server V9 with squid, dansguardian and clam. I have fetchmail wroking to bring in mail from our externally hosted website and delivering it to users mailboxes in exchange server. That was easy following guides on the internet. However my brain is failing me now. How do I reverse the process and send mail to the outside world. I need to be able to do this without authentication. At the moment i am using a windows environment with exchangepop3 which uses smarthost to connect to the ISP smtp server. Please help or point to a simple guide. If i cannot solve this soon i will have to revert to microsoft solution for the proxy server.
View 7 Replies View RelatedI downloaded Evolution last night but I am unable to connect to MS Exchange 2003. Does anyone know of a sure fire way to get connected?
View 1 Replies View Relatedi want to configure my MS Exchange server email in Evolution of Fedora. as, Ubuntu 10.10 gives the dropdown for MS exchange server, however in fedora 14 the same is not available.
View 2 Replies View RelatedI am using Fedora 12 and Thunderbird 3.0.4 version I am trying the connect it to the IMAP server but it does not work (no authentication).
- IMAP with SSL
- SMTP with none
Though it works for other email client (Evolution). I there a problem with the thunderbird itself or am I missing something special to configure that I dont know of?
I have a Nagios box set up on the corporate LAN. I'm trying to get it to send emails to both internal Exchange addresses as well as doing a direct delivery to internet domains.
I have looked at a few logs and it appears that Postfix is not doing proper DNS lookups on the internal servers. It keeps trying to connect to the domain controllers. I have an MX record specified.
I am looking for an equivalent software of Microsoft Exchange server. Right now we are using MS Exchange Server with 40 users. Can I transfer this setup to any equivalent RHEL programs? Is There A Linux Equivalent To Microsoft Exchange?
View 4 Replies View RelatedI have a linux box on my DMZ with postfix on it. I have exchange on our internal LAN on 10.152.0.104.
View 6 Replies View Relateddo I have an alternative for Microsoft exchange server under linux ?
View 3 Replies View Related
