I have a fresh install of suse 11.0 and there is no 3d acceleration available. If I use the suse repository, which driver do I need to enable 3d accesleration? The video is integrated on the motherboard. The box is an hp pavilion a1130n and amd 3500+ processor. I installed the same suse 11.0 on a dell box with an ati 128 rage and 3d was enabled after the install.
View 2 RepliesI have installed Open Suse 11.1 on two different machines. One contains an ATI X850 video card, and the other contains an ATI X1950 video card. I updated the ATI drivers on the 850 card and it works like a dream. I updated the ATI drivers on the 1950 card and Suse becomes unusable. System works fine before the update. Before the update I ran it at a resolution of 1280 x 1024. I thought I would lower it to 1024 x 768 to see if that would help, but it does not. I dual boot with WinXP, and card works fine with that setup at 1280 x 1024, so I would suspect this is a specific problem with my Suse setup as opposed to a Motherboard issue.
View 4 Replies View RelatedAlright, Lenny has a working "fglrx-driver" package for my laptop, but Squeeze does not. Would it be possible to install the one from Lenny on Squeeze since Squeeze has newer libraries and such? I know I can't install new stuff with older libraries, but can I install the old stuff with newer libraries? I am at the end of my rope here! I mean ATI sucks and we all know this, but I've always found a Linux/open-source alternative that worked, until Squeeze.
View 10 Replies View RelatedI want to attach disk with Suse 11.2 to another motherboard with Integrated ATI Radeon HD 4290 GPU ( at the moment I am using Nvidia GeForce 6800). How can I change settings for new video chip?
View 4 Replies View RelatedI have been using Debian for a few weeks now (love it, besides it being a little bulky). and have everything going besides wireless and my graphics card, the former being less important to me. I haven't had any problems running Debian without a graphics card, but I know I will need it to play games, configure a 3d desktop if I choose, etc...
View 14 Replies View RelatedI just installed OpenSUSE 11.2 x86_64 on a new computer with ATI Radeon HD 5770 graphics card. I have included ati in the update repositories. I saw that x11-video-fglrxG02 and ati-fglrxG02-kmp-desktop are NOT checked, so, I selected both in YAST2, then, OpenSUSE started to download the required files. but, in the middle of downloading, I got a "wrong digest", said that ati-fglrxG02-kmp-desktop has wrong checksum.
View 4 Replies View RelatedAll the three files I downloaded can not been played by Banshee. I got the message like below when I use search the code, so I installed all the Gstreamer I can find.
* Windows Media decoder (GStreamer, 32 bit, i586)
* Advanced Streaming Format (ASF) demuxer (GStreamer, 32 bit, i586)
During that I also did some update, but the problem still the same.
I have an Aspire 5100 with ATI Radeon Xpress 1100 and have been happily running Ubuntu 8.10 until now when support has ended. I continued with 8.10 because the graphics have been fine with my system.I also have 10.10 installed and apart from the graphics, I would have no problem changing/upgrading.The problem is the glare, after a while it is very hard to work on.Is there anything I can do that's not to technical to reduce the glare.
View 5 Replies View RelatedI just did an install from opensuse 11.0 to 11.3 using the live web install. After the install, I found that the monitor always reverts to 87hz refresh rate and must be manually adjusted to 60hz. Also, there is no adjustment for the monitor resolution beyond 1024 x 768. I can not find the video card info in yast like it was before. Do I need to add the ati sources in yast? Will that give me a way to adjust the video card properties? Video card is the ati rage. Box is a dell optiplex pentium 3.
View 1 Replies View RelatedI'm trying to install a GeForce 8600 XT card into novell Open Enterprise SUSE 11 so that I can get the 3D Cube to work. It currently does not work with the default nvidia card onthe motherboard.I can not find the correct driver for the GeForce 8600XT card. Can someone identify the driver I should be using please? Then if someone could also direct me to the "How to install a Video Driver" tutorial,
UPDATE:I've downloaded the correct drivers but it still says that my hardware does not support Desktop enhancements etc ... I think the GeForce 8600 XT just doesn't support 3D accelleration ... period.Can someone suggest a reasonably priced video card that is easy to install and which supports 3D Accelleration please?
I'm running Ubuntu 10.04 on a PC with the integrated Radeon X200 card. Currently, I have the free Radeon drivers, but they're either awful or aren't working properly. I get some wonky graphics errors, and any 3D game crashes as soon as the 3D graphics are to be displayed.
My card is no longer supported by fglrx. What can I do?
I can usually solve this type of problem myself, but this time around I'm totally stumped. Can anyone lend a hand? A little background: I have an HP Pavilion ZV6233NR with no screen installed, connected through the VGA to my LCD TV. This is a somewhat older desktop replacement laptop. I have repurposed it to run as both a server and a media center (e.g. it connects to my TV). I'm upgrading from Debian Etch to Debian Squeeze (never installed Lenny). With Etch, I used the proprietary fglrx driver, however the fglrx package in Squeeze doesn't support such old hardware (obviously), but the new foss radeon driver does.
The problem: First, suppose I run X with no arguments, the (EE) and (WW) lines in /var/log/Xorg.0.log read (excluding missing font files):
(WW) Falling back to old probe method for vesa
(WW) Falling back to old probe method for fbdev
(EE) open /dev/fb0: No such file or directory
[code]....
I've attached the full Xorg.0.log for that second case (radeon driver using the conf file), in case that helps. Three things I've tried (but for all I know bungled, test me if you think I might have):Fresh installation from the CD. (In case I had left over fglrx stuff lying around.) Horizontal and vertical refresh rates for the screen (although I didn't actually look them up in the LCD screen's manual).
Setting modes in the screen section to restrict the resolution and/or color depth.
I have recently installed 11.3 onto a computer I just dropped a new mobo/cpu/memory into. At first everything worked great! (minus a few video streaming issues...but that is for a later date) Then, a few days ago, I let it do an update. Boy to I feel stupid now. I guess if it ain't broke..... So, now I don't have sound in the browsers or for the video players...such as xine. I do however still have sound with Amarok and system sounds when it boots up.
I have deleted the sound device in Yast and let it re-install several times. I tried different setting there as well. Checked and rechecked then checked again the mixer settings. Made sure my group settings included audio...just in case. Now Amarok and the online video play at warp speed, and only Amarok gives me sound....garbled...but sound. The system keeps telling me when I reboot that "one or more sound devices were removed" and wants to know if I want it to ignore them from now on. I've answered yes and no several times.I've also tried updated the alsa drivers in the software management of Yast. Can someone please help me before my wife gets mad at me for converting this computer to Linux?
Here is some information.
Password:
The "Warp Speed" for the video and audio was resolved after removing and then re-installing the audio driver and a quick reboot. But for some reason I had to reboot yet again to get the internet connection working again. This has happened to me a couple of times now. Also, when I try to adjust the Pulseaudio config under "other"in the audio config of Yast,it says it is not installed. When I try to install, it has a conflict with another program.
I'm still having problems with firefox 3.5 on Fedora 11. My computer freezes; and it takes a power-off reset to unlock it. Keyboard and display are unresponsive (x-server crash). It crashes even with Firefox 3.5 running in safe mode.
Configuration:
Hardware:ATI Radeon� XPRESS 200 Chipset
Kernel: 2.6.29.6-217.2.3.fc11.i586 #1 SMP i686 athlon i386
firefox.i586 3.5.1-3.fc11
flash-plugin.i386 10.0.32.18-release @adobe-linux-i386
Koji was used to update kernel and firefox. Thanks to wangmaster and other members, I was able to install Firefox 3.0.12, which is run using a different profile. Do I need a debug version of Firefox for a dump? Do I need to send this AMD machine to the landfill or North Carolina?
I have a problem with my video card since I installed Ubuntu Maverick. Compiz is working, I have Desktop effects and everything but.. i have a lot of troubles too. I can't watch full size video in ..... (it's very slow or totally freezing every time i try fullscreen option). Google Earth working, but when zoomed too much (to see map closer), i am seeing a lot of lines and strange pixels.
Everything was working good on CentOS, but after getting into Ubuntu.. something went wrong. I think the problems are coming from the drivers.
I have this drivers installed:
Code:
I followed this guide - https://help.ubuntu.com/community/RadeonDriver - for installing everything again, and I also added the Xorg Edgers PPA [url]. When I have xserver-xorg-video-radeon & ati drivers installed, my system have all the problems listed above and don't have 3d acceleration (which I need a lot for running Cedega and VMWare).
This is output from glxgears (while having the drivers installed)
Code:
And this is glxinfo in verbose mode:
Code:
(notice I have Direct Rendering, but not 3d acceleration, since it have troubles with the driver.. but the file is in the same folder it's searching for it)
When I remove them from the system (purge), and I use only the Edgers PPA and:
Code:
I can watch full size video at ....., my computer hibernates and wakes up after (which is causing a lot of problems if I'm using the xorg-ati & radeon, laptop freezes requiring hard restart). I can use Google Earth without having troubles, but.. still can't run Cedega and VM, because I don't pass the tests for 3d acceleration.
This is output of my glxgears & glxinfo (in verbose) after removing the drivers and restarting X.
Code:
i have this video card 01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200M] IT suspends but it looks on resume with the opensource radeon driver. It never worked with the open source driver for me. It worked with the proprietary driver but those drivers are no longer compatible with the new xorg(catalyst/fglrx worked in ubuntu 8.04 and 8.10 but no high1er and in debian lenny) My question is:If you have this card and manage to make it resume on a recent distribution please tell me if you did something to make it work or it just worked.
P.S I do not use xorg.conf and i have only open source driver installed,currently i have a ubuntu and a kubuntu installed on this laptop, i did not tried any fix in the present because i tried them before so thuis operating systems are clean(nothing wrong with the libs or configs)
I've got an older HP Pavilion dv8000 laptop with ATI Radeon XPRESS 200M 5955 video. This worked fine out-of-the-box with 13.1. With 13.37 I can't get KDE desktop effects to work, glxgears reports about 50 fps, and the system can suspend but not resume. I have no xorg.conf at all. Here is the glxinfo and current Xorg log. Just to note, this is with Slackware64 13.37 with the multilib stuff installed.
View 4 Replies View RelatedI have a computer with an integrated graphics card. It is ati radeon xpress 200 series. It have installed OpenSuse 11.1 on my computer with KDE 4.1. I have heard that we have to manually install ati and nvidia drivers. Or can the open source drivers run my card. has the drivers for my card already been installed. Or should i install it manually. I donot have an internet connection on my pc. but i can download the required files from another computer and bring them to my pc.
View 3 Replies View Relatedi'm running Kubuntu 10.04 with KDE4.5 on HP DV5000 and i have problems with the video drivers as usable look where is the problem
LIBGL_DEBUG=verbose glxinfo
name of display: :0.0
libGL: XF86DRIGetClientDriverName: 5.3.0 r300 (screen 0)
libGL: OpenDriver: trying /usr/lib/dri/tls/r300_dri.so
libGL: OpenDriver: trying /usr/lib/dri/r300_dri.so
[code]....
I don't get it on [URL] say R300 is for Radeon 9700PRO/9700/9500PRO/9500/9600TX, FireGL X1/Z1 (2D only) and RS400 is for Radeon XPRESS 200/200M IGP ( What HP DV5000 have ) But in the middle of the info i have OpenGL renderer string: Mesa DRI R300 (RS400 5955) 20090101 x86/MMX+/3DNow!+/SSE2 NO-TCL on lsmod | grep radeon i have
radeon 901424 2
ttm 54611 1 radeon
drm_kms_helper 30726 1 radeon
[code]....
Fedora 12, latest kernel, x86_64.
I have an Asus M4A78L-M motherboard that has integrated ATI Radeon HD3000 video. Should I be looking for a driver specific to the integrated video, or should I be looking for a driver specific to the motherboard? I'm not sure if I should look for something different if the video is integrated onto the motherboard, as opposed to a separate video card. This is what I found: http://support.amd.com/us/gpudownloa...5&lang=English
Are there best practices for updating video drivers before I make any changes? I don't want to hose my video.
I've found that whenever I play a 3D game on Ubuntu, the graphics go crazy and make the game unplayable. I've found this an various games such as SuperTuxKart and Alien Arena.By the way, I'm running an ATi Radeon Xpress 200 (integrated graphics) with the default Ubuntu drivers.
View 3 Replies View RelatedThere is running gOS on my computer (Ubuntu baset OS) and I want to install the Video Card driver for ATI RADEON 9250.
Ifound the driver in the official site =>> http://ati.amd.com/support/drivers/l...n-prer200.html
And I also saw the instructions of installation =>> [url]
But I cant instal the driver. When I write the comand sh ./ati-driver-installer-8.28.8.run (of course the file is in the home directory)the terminal window writes:
PHP Code:
And then written in the instruction: The ATI Proprietary Linux Driver Setup dialog box is displayed but no window or dialog box is displayd.
a powermac G4 with radeon 9000 RV250 in ubuntu 10.04 ppc i just want the graphic work better
View 9 Replies View Relatedi installed kubuntu 9.04 yesterday and updated it with everything that was available, i have ati radeon xpress 1100 and i got everything running fine including kwin effects but i have a small problem i cant figure out how to fix:
When i run glxgears and put any window on top of it, i can still see the 3d gears rolling and i think this same problem is responsible for occasional artifacts on the screen. Its a very minor problem but i would like to see if fixed because i cannot use google earth properly, it seems that any 3d application likes to be focused on the screen, its like they flicker while being overlaid on top of everything.
Also i read the countless threads here complaining about not being able to use fglrx etc because of updated xorg. Well the reason im using 9.04 is because my wireless card alfa awus036h does not work with kernel > 2.6.31 and i have already tried kubuntu 9.10 on this laptop i wasnt having any problem with the display. All the kwin effects ran fine and no distortions of any kind. Seems there is some bug in 9.04.
I'm trying to install the driver for my ATI Radeon X1600 Series video card. I got the driver from the ATI site. Heres the link: [URL]... I'm using 10.04 LTS. I have attached a screenshot of the message I get when I run the installer.
View 4 Replies View RelatedI'm a new Mandriva user,and have no clue about Linux system,but to be honest I don't want to use Windows product anymore. So I got the Mandriva 1 Spring Gnome,and installed it on my DELL Optiplex Desktop,works fine and very fast,therefore I decided to do the same with my Studio XPS 1640,but after I got a dark screen,so I used an external display(My TV) then realized that it doesn't support the video card on it ( ATI Radeon HD4670 ),and I don't know what to do.
View 1 Replies View RelatedAfter dist-upgrade a few days ago, X refuses to kick in.
Xorg.0.log reads
Code:
Fatal server error:
no screens found
Please consult the The X.Org Foundation support at http://wiki.x.org
Please also check the log file at "/var/log/Xorg.0.log" for additional information. lshw reads that Xpress 200M is claimed by radeonfb driver.
At this moment, no fglrx packages are installed.
System is Toshiba laptop.
I do not think ATI dropped support, however, even without fglrx, nothing works.
I intend to re-install open suse 11.2, 32-bit. On a previous install,suse did not provide a grub entry for ubuntu.My current setup has
ubuntu/root on /dev/sda6
ubuntu/home on /dev/sda7
ubuntu/usr/local on /dev/sda8
[code]...
I've got several language multimedia CD-Rom's, made for Windows 95/98/98 SE and 2000, that I'm using by means of my daughter's old PC (Win 98 SE O.S.). However I noticed, also, that you can perfectly use them even with Windows Vista. What I'd like to know is if you can use them even with Suse/Novell and (why not?) OpenSuse Linux.
View 4 Replies View RelatedOK... I tried everything i could think of... but i still cannot get my Open SUSE 11.1 to mount my samba share at boot! I still don't understand the 11.1 boot sequence. can NE one help me... tell me what files to give you output from... Ty guys P.S. My shares originate from a Windows Server 2003 RC2 machine, and it's dns server doesn't work correctly... so my mount command is
mount -t //192.168.x.x/files/ /nET/ -o username=linux,password=xxxxxx
please let me know what other info you need... I don't have the internet, so it will be tommorow b4 i see this again!!! Thanks