Red Hat :: Static Network Configuration On RHEL - Network Is Unreachable
Apr 27, 2010
setup my static network connection Here are my details :
IP : 172.16.152.137
Subnet : 255.255.255.192
Gateway : 172.16.152.191
Primary DNS : 172.16.0.1
[code]....
but after this setup when i restart my network #service network restart while bringing up the eth0 the following message is displayed before [OK] - RTNETLINK answers : Invalid Argument now it seems either this setup is wrong or not sufficient to set up the connection, whenever i try to ping 172.16.0.1 it showing connect : Network is Unreachable
View 11 Replies
ADVERTISEMENT
Jul 17, 2011
I installed openSUSE on one of my work system. The network port wasn't working when I was installing, but works fine now (checked in Windows). But for some reason, I am not able to configure the network. I used both Dynamic and Static IPs (both work fine in Windows) but still no go. I am using Yast Control Center for this purpose. I can't even ping the default gateway when I am using custom settings. When I use dynamic settings, it says Unreachable Network.
View 7 Replies
View Related
Jul 19, 2010
I moved to static Ip method for my laptop. I edited the interfaces file and it seems to work since I am writing this message from that laptop, but I have a new problem with my Debian. The mounts are not mounted during the startup anymore. Before I was using the network manager method and the nerwork mounts were all fine. Now with this method, they are not mounted and I need to mount them by firing "sudo mount -a" manually.
View 2 Replies
View Related
Oct 11, 2010
My os is debian 5.0, netcard is RTL8168D/8111D. I can't use the Static ip, if I setup static ip, output "not found network device", but the network driver have loaded and if I use DHCP mode everything is ok. do you understand my english? What my next steps should be?
View 7 Replies
View Related
Jun 27, 2011
I have a Dell PowerEdge SC430, Squeeze 6.0.2 box, Broadcom NetXtreme NIC which works fine DHCP. The network-manager package is not installed. I have now reconfigured /etc/network/interfaces for a static IP:
auto eth0
iface eth0 inet static
address 192.168.1.2
[code]....
View 7 Replies
View Related
Apr 3, 2011
The wireless network on my laptop is configured with a static IP. (not using nm). When I take the laptop out of the range of my wireless router the essid is becoming off/any therefore when I'm back in range the connection is not reestablished and to re-enable the connection I gotta do "iwconfig wlan0 essid <essid name>" otherwise there is no connection. Make sure that essid stays configured unless I manually want to change it?
View 1 Replies
View Related
May 27, 2010
issue in starting up Open view monitoring on couple of linux servers and here is the output from mii-tool looks like.
eth0: 100 Mbit, full duplex, link ok
eth1: 100 Mbit, full duplex, link ok
[code].....
Based on what I understand, eth0 goes to monitoring and the other 2 ethernet cards go to FE. I am not an expert in system administration but would like to know if there is any issues with the above settings/configuration (in fact, im also looking for what do they infer and what is the settings?
View 2 Replies
View Related
Oct 12, 2010
I installed RHEL 6 Beta 2 on ESX box and found that network is to be manually started through ifup command.
View 6 Replies
View Related
Jan 14, 2010
I want to create a small network of 3-5 computers. I want to have one computer as my server and have services like NFS, DHCP, NTP, etc. I want to connect it to 2-4 other clients that have the bare minimal installation of linux on them. I would like 1 client computer to have a static ip address and I would like another to receive a dynamic ip address from the server. How would I go about doing all of this without the assistance of GUI's? I want to be able to do all this with the ks.cfg and network config files.
View 4 Replies
View Related
Mar 5, 2010
How do I activate static DNS for mobile broadband. I can't find any place to write down this information. Settings are made in Network Manager - not Yast.
View 3 Replies
View Related
Jan 12, 2010
I'd like to have a set up where my Ethernet card has a static IP set up but my WiFi card doesn't.Currently I have a profile for this set up in Network Manager, however on boot up and every time I replug the cable Network Manager chooses the default "auto eth1" profile. I manually have tochoose my own profile for the Ethernet card every time. How can I make it default??I know the workaround would be to use ifup but then I lose the ability to quickly change access points for my WiFi card so that's not a solution for me
View 9 Replies
View Related
Aug 20, 2010
New SUSE 11.3 install connects to network/internet etc OK with DHCP-assigned IP address. When I switch to static IP, I can no longer ping internal network, or anything else. This works OK with SUSE 11.2 on same hardware and (as far as I can see) same setup. Some diagnostics are shown below.
Firewall
Disabling the firewall makes no difference.
Not using a network manager (can't see how to assign fixed address if I do - all greyed out).
ifup eth0:
eth0 device: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
SuSEfirewall2: Warning: no default firewall zone defined, assuming 'ext'
(not sure why the warning - eth0 is assigned to external in the firewall setup).
[code]....
View 9 Replies
View Related
Mar 25, 2010
I have one server with 4 network interfaces:
eth0: 192.168.0.0/24 - local lan A
eth1: 200.1.2.3 - internet link - default route
eth2: 192.168.10.0/24 - local lan B eth3: 192.168.20.0/24 - local lan C
Lan A - Default routing to eth0
Lan B - Default routing to eth2
Lan c - Default routing to another server but the workstations has static routing to this server too.
Everything is working fine on Opensuse 11.1 until I upgrade this sever to Opensuse 11.2 ( Reinstall, not update at all ). After upgrade to 11.2 the routing across local lan interfaces simply not work, if you try to ping lan-to-lan you got the message: Network unreachable, even with the IP Forward enable, but the default route is working fine trough the SNAT.
I've come back to Opensuse 11.1 and everything become normal, does anyone have an problem like this? Maybe a bug? PS: I do not try to disable the AppArmor, next weekend I will try Opensuse 11.2 without the AppArmor and post here anyway.
View 9 Replies
View Related
Jan 11, 2010
I've got router with: eth2 - local network (192.168.1.1), ppp0 - uplink (x.y.z.a)
my firewall:
Code:
# Generated by iptables-save v1.4.5 on Mon Jan 11 12:22:25 2010
*raw
:PREROUTING ACCEPT [1038480:666298388]
[code]....
somehow iptables -t nat -A PREROUTING -i eth2 -d x.y.z.a -j DNAT --to-destination 192.168.1.1 helps, but imho there should be some other solution. kernel is 2.6.31.6, architecture is x86_64.
P.S. i've also tried iptables -A POSTROUTING ! -d x.y.z.a -s 192.168.1.0/24 -j MASQUERADE that didn't help either.
View 10 Replies
View Related
Mar 7, 2011
I have two linux servers, I tried to ping from one linux box to another and vice versa but error message is "connect: Network is unreachable" Where as If I tried from windows machine I am getting the reply from both the servers.
C:Documents and Settings>ping bnkprod
Pinging bnkprod.softtech.com [172.20.40.141] with 32 bytes of data:
Reply from 172.20.40.141: bytes=32 time=16ms TTL=64
Reply from 172.20.40.141: bytes=32 time<1ms TTL=64
Reply from 172.20.40.141: bytes=32 time<1ms TTL=64
Reply from 172.20.40.141: bytes=32 time<1ms TTL=64
Ping statistics for 172.20.40.141:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 16ms, Average = 4ms
View 2 Replies
View Related
Aug 17, 2010
Flashed bios lastnight on 13.0 desktop.
all winblow$ are fine.
lspci shows ehthernet card
did 'netconfig' and
'route -n' shows default settings as if /etc/rc.d/rc.inetd1.conf were never set.
oh yes, i manually edited this too. mv'd and netconfig'd.
View 5 Replies
View Related
Dec 27, 2010
I've been having a lot of trouble with getting wireless networking devices to work. I guess I have a lot of company, since mfrs don't seem to be very interested in supporting Linux.It seems that one common symptom is that, when I try to "Ping" using the Terminal, I get "network is unreachable".Does this mean anything specific, or is it a general output whenever the network is not carrying on two way communications? Does it mean that the wireless interface is down? Does it mean that the wireless hardware is not transmitting? Not receiving?
View 3 Replies
View Related
Jan 3, 2011
My ubuntu installation was running fine with the Belkin F7D1101 v1 after using this install method:[URL]..But, after allowing ubuntu to autoupdate many programs (don't remember which ones), the device stopped working. I checked all of the commands in the link above. They are all still functioning. dmesg throws no errors, but it terminates with
<code>ADDRCONF (NETDEV_UP): wlan0: link is not ready</code> Are there any network files which may have been overridden from autoupdate? iwconfig wlan0 shows "Access Point: Not-Associated" What output can I show you to help me find the problem?
View 1 Replies
View Related
Jan 18, 2010
I want to add this route but I am getting this error message. What is the reason of this problem? I cant add this route? how can i add?
Code: [root@linux/]# route add -net 10.1.0.0 netmask 255.255.0.0 gw 10.2.0.1 eth0 SIOCADDRT: Network is unreachable
View 11 Replies
View Related
May 3, 2010
Recently our sys administrator decided to go to static IPs from the earlier assigned dynamic ones. This has created some havoc in my open suse 11 and I do not have access to network. I tried using the YAST network configuration manager, after everything is done it shows 'network wired' but unable to ping.
View 1 Replies
View Related
Jan 29, 2011
I'm using debian lenny.When I boot with kernel 2.6.36, ping always respond with Network is Unreachable. But when I boot with kernel 2.6.26 it works. I can't even ping the dafault router of 2.6.26 kernel when I am at 2.6.36. Also, system/administration/network does not show any connections while it shows something at the other kernel.
View 1 Replies
View Related
Oct 3, 2010
I have a network printer directly connected via ethernet cable to an Ubuntu netbook, but pinging the printer fails, giving "Host Unreachable". The network light on the ethernet socket is lit green, and there is nothing else cable-connected to the network - just a simple cable connection between the netbook ethernet socket and the Network printer (a HP Laserjet 4200n). Ping works fine if I plug the cable into a different machine (a Win XP box) and ping from there, so it's not a cable or IP address problem.
This sounds simple enough and should work, but I'm stumped. Clues, anyone?
View 2 Replies
View Related
Dec 15, 2010
I'm experiencing massive latency/unreachable problems on my Linux machine. It's true for all network connections, here's an example of me trying to ping my router:
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=15115 ms
64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=14107 ms
64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=13107 ms
64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=12107 ms
64 bytes from 192.168.0.1: icmp_req=5 ttl=64 time=11108 ms
[Code]...
I've tried now with both the maverick default kernel and 2.6.37-rc5 kernel (both 64 bit), same result. If I take the card up and down (ifup, ifdown) performance is restored for a little while, then it's back. I've tried changing cable, network card and router port but no luck.
View 4 Replies
View Related
May 25, 2011
I use DNS on my server as a chasing DNS so its not fully configured. I seem to be having trouble with IPV6 addresses. I'm guessing this is linked to the 6to4 tunnel I have set up to my windows box, but I'm not really sure.
Code:
May 21 18:00:16 hyrule named[1148]: error (network unreachable) resolving 'D.ROOT-SERVERS.NET/AAAA/IN': 2001:dc3::35#53
May 21 18:00:16 hyrule named[1148]: error (network unreachable) resolving 'B.ROOT-SERVERS.NET/AAAA/IN': 2001:500:1::803f:235#53
May 21 18:00:17 hyrule named[1148]: error (network unreachable) resolving 'zg.akamaitech.net/AAAA/IN': 2001:503:a83e::2:30#53 .....
View 3 Replies
View Related
Aug 16, 2009
I installed centos 5.3 x86 at vrtualbox on windows 7 x64 as host. The ping answers "network is unreachable", ifconfig has an ip "192,168,51,100". At control panel, I seleted intel PRO/1000MT Desktop Host only. Is this centos's problem?
View 3 Replies
View Related
Jan 16, 2011
When ever i try to access 202.164.53.122 through ssh i get the following error message:
Couldn't establish connection to proxy: Network is unreachable ssh_exchange_identification: Connection closed by remote host
I have a account at 202.164.53.122.firewall is on.
View 1 Replies
View Related
Aug 7, 2011
I am plagued by the following error when attempting port forwarded connections to my minecraft server. Port forwarding is good and test ok on router based firewall. No iptables entries. Natty N, all updates current.
[INFO] Disconnecting CascadianNW [/184.100.247.218:57787]: Failed to verify username! [internal error java.net.NoRouteToHostException: Network is unreachable]
java.net.NoRouteToHostException: Network is unreachable
Some discussion indicate jvm network connection issues related to ipv6, but they are old posts.
View 1 Replies
View Related
May 25, 2010
Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .
View 1 Replies
View Related
Mar 3, 2011
I was playing with my debian server when something went totally wrong while i was editing something on my network interface,i removed those crap that i wrote and left the network interface configuration as it was
Like for example after re-editing my network interface,it was like :
As i did a network restart, i get this error saying :
There is already a pid file /var/run/dhclient.eth0.pid with pid 2802 killed old client process, removed PID file.
What is this error and how can i fix it,because every time im re booting my server i lost my network config.
View 1 Replies
View Related
Mar 27, 2010
I have a Canon MX860 network printer but I cannot get it to connect with my openSUSE 11.2 computer
View 9 Replies
View Related
