Red Hat / Fedora :: E1000e: Probe Of ... Failed With Error -2, CentOS 5.5 Intel 82574L
Mar 15, 2011
I am trying to use a rig with Gigabyte GA-880GA-UD3H mother board and Intel 82574L based NIC (EXPI9301CTBLK) under CentOS 5.5. Unfortunately I have issue with the NIC - during boot it fails to initialize:
[Code]....
I receive the same result with the original e1000e driver from the distribution, the latest elrepo driver and the latest driver from Intel site (as seen in the example). I have tried also 2.6.37 kernel version - with the same result. The adapter however works fine under Windows (MiniXP from Hiren's BootCD) and with Ubuntu 10.10 LiveCD.
View 3 Replies
ADVERTISEMENT
Aug 23, 2009
I just installed Fedora 11 on an AMD CPU PC. I get the following error during boot up.Aug 22 21:42:07 dragon8 kernel: aic7xxx: probe of 0000:00:0a.0 failed with error -38 Because the aic7xxx has the error, it does not load the st module. I manually loaded the st module, but the /dev/st? devices do not get created, I assume because of the aix7xxx error.I can access the Adaptec AHA-2940W Bios during boot up and see the 2 tape drives that are connected to it.
View 2 Replies
View Related
Nov 18, 2010
I have a clean install of mythbuntu 10.10 and I am trying to get a DVB-T USB stick working for the last 2 weeks. Its a MobiDTV and it seems to have the same chipset/USB ID as EzCap_DVB_T_Stick. I followed the instructions on the [URL] and eventually got the driver compiled (I had to amend some code, change "Bool" pointers to "bool" and add a FIRMWARE MAX_NAME 30 constant). I also copied the af9035 FW file to the firmware directory.
lsusb:
Bus 002 Device 004: ID 15a4:1001 Afatech Technologies, Inc. AF9015/AF9035 DVB-T stick
but it is not working; probe is failing:
dmesg:
[ 105.104195] DRIVER_RELEASE_VERSION : v2.0-1
[ 105.104203] FW_RELEASE_VERSION : v8_8_52_0
[ 105.104209] API_RELEASE_VERSION : 200.20081203.0
[ 105.110713] [Device_init] Error 1
[ 105.110733] dvb_usb_af903x: probe of 2-5:1.1 failed with error 9
I bought the hardware with Windows 7 MCE in mind. I have no Windows 7 disk so I installed Mythbuntu on it to see if build was solid and now I don't want Windows any more.
View 2 Replies
View Related
Feb 20, 2010
I'm looking through dmesg and see
Code:
nvidia: probe of 0000:00:03.5 failed with error -1
the corresponding bus is
Code:
00:03.5 Co-processor: nVidia Corporation MCP79 Co-processor (rev b1)
Subsystem: nVidia Corporation Device cb79
Flags: 66MHz, fast devsel, IRQ 16
Memory at 93300000 (32-bit, non-prefetchable) [size=512K]
Kernel modules: nvidia
from where I infer that the module is correctly loaded though. Do you guys know what is the -1 error code? is there any way I could check if the coprocessor is currently working?
View 2 Replies
View Related
Mar 2, 2011
OS:Debian Linux 2.6.32-5-amd64 Should i need to worry about these error messages? If 'Yes', how to check and fix? When it boot,
/var/log/syslog
Mar 2 23:29:03 ipb167 kernel: [ 1.465629] PM: Error -22 checking image file
Mar 2 23:29:03 ipb167 kernel: [ 4.110123] amd64_edac: probe of 0000:00:18.2 failed
[code]....
View 2 Replies
View Related
Nov 8, 2010
Just a heads up to others. There is a kernel regression in the 2.6.35 kernel with regard to, some but not all Intel Gigabit ethernet adapters using the e1000e driver. After an otherwise successful upgrade from fedora 13 to 14, no ethernet connection could be made while using the upgraded 2.6.35 kernel that comes with fedora 14. The 2.6.34 fedora 13 kernels work fine and were fortunately still available after the upgrade.
I have personally seen the identical malfunction on all 2.6.35 kernels I've tried with both Arch and Aptosid and have seen similar reported problems on the Gentoo forum. In each case, going back to a 2.6.34 or upgrading to a 2.6.36 kernel solved the problem so this is almost certainly a kernel issue. My onboard Intel Gigabit ethernet adapter is:
$ lspci -vv | grep Ethernet
00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02)
I believe the intel ICH8 chipset motherboards are the ones primarily effected.
View 9 Replies
View Related
Mar 5, 2011
Just got a SuperMicro X8SIL-F board, and I'm having trouble getting the onboard Ethernet controllers to work. They are both Intel 82574L Gigabit. One of them has (rev ff) at the end in lspci.
Out of the box, both controllers show up as eth0 and eth1, but the connection on either is flaky and unreliable. I installed an updated driver from the Intel Download Center, but now I lost one of my controllers and only have eth0. They still both show up in lspci. I installed the driver by extracting the archive and running make install in the src folder, then restarting.
I'm running Ubuntu 10.04 amd64 64bit 2.6.32-24-generic.
View 2 Replies
View Related
Feb 14, 2011
I'm having issues with Ubuntu 8.04 to see my Intel 82574L ethernet card. Ubuntu is not detecting it at all.
I downloaded the drivers from
[URL]
copied it to the server, untarred, make install ,and now i'm getting notifications that kernel-devel is not installed. I installed linux-headers from the install cd ( ihave the alternate and server one), but i cannot find any kernel-devel or linux-kernel-devel. The driver still does not want to build after installing linux-headers.
I need to use Ubuntu 8.04 due to some specific requirements, do i need the network cards to work.
View 2 Replies
View Related
Sep 10, 2010
NIC: Intel 82574L Gigabit mobo network card
Issue: After the server has been up for a random amount of time, the network connection is lost. Attaching a console and looking at ifconfig I see a large number of dropped packets and collisions.
use;
Code:
lspci -vxx
to list the make manufacture of NIC and the device driver it is using.
In this case: Intel 82574L, e1000e
Look in var/log/messages to get the version of the driver, in this case 1.0.2
Download .gz file with source code, follow instructions to install newest driver (e1000e.ko), in my case version 1.2.10. [URL]
View 2 Replies
View Related
Apr 6, 2011
in order to using the SR-IOV, according the guide HOW_SRIOV [Moderator edit: fixed link.]but i can't got the VFs.so i try to compile the driver :igb-2.4.13 and igbvf1.0.7.but i failed to install them.when i make install the igb-2.4.13 i got the errormsg:root@localhost src]# make installakefile:106: *** Linux kernel source not configured - missing version header file‚[root@localhost src]# i alreadly installed the kernel-headers-2.6.18-194.32.1.el5.x86_64.rpm .some system info maybe needed:Information for general problems.
== BEGIN uname -rmi ==
2.6.18-164.el5 x86_64 x86_64
== END uname -rmi ==
[code]....
View 6 Replies
View Related
Apr 7, 2009
After doing a clean base install of CentOS 5.3 on a test server, I started having problems with network disconnects. While SSH into the box, I would be intermittently disconnected from the SSH session. At first I thought it was my workstation, but after running ping tests from multiple machines on the network to the test box, it became apparent that the test box was dropping packets. When I lose my SSH connection, the pings also start timing out, for a few seconds, then start again. I increased the console logging and I can see when the ethernet port goes up and down when I physically disconnect the cable, but it does not go down or lose link when the disconnects occur. I changed the NIC ports being used and had the same result. I tried with a different switch with same result. I reinstalled CentOS 5.2 and the problem went away.
Upon further investigation, I found that CentOS 5.2 is using the e1000 driver for my NICs and CentOS 5.3 is using the e1000e driver. I resinstalled CentOS 5.3, and tried using the e1000 driver instead of the e1000e but it no longer detects my NIC's... apparently they moved the support from e1000 to e1000e. I have spent the last 3 days googleing for info on this problem and have not found a solution. Any recommendations? Should I submit a bug report?
[Code]...
View 12 Replies
View Related
Jan 6, 2010
I am having trouble upgrading from old grub to grub-pc. I have a clean install of 9.10 on a system with a new ASUS motherboard with Nvidia RAID configured as RAID 0.Although I read the page on SATA pseudo-RAID, this doesn't seem to apply, as both 9.10 and Windows XP installed cleanly without any additional drivers required.I did notice that contrary to the documentation, 9.10 installed with grub v0.97, not the new one as claimed. It is working fine, but just to be ornery, I'm trying to upgrade to the new one, and this is where I ran into trouble.Whenever I try to run grub-upgrade, I get an error from grub-probe that 'no mapping exists for' my raid partition. Apparently grub-probe can deal with the device, but not with the fs_uuid, as follows:
twescott@latitude:~$ sudo grub-probe -t device /boot/grub
/dev/mapper/nvidia_fcacbeib5
twescott@latitude:~$ sudo grub-probe -t fs_uuid /boot/grub
grub-probe: error: no mapping exists for `nvidia_fcacbeib5'
The system seems to be recognizing the RAID with no problems, as in:
twescott@latitude:~$ sudo blkid
/dev/mapper/nvidia_fcacbeib1: UUID="28D83EB2D83E7DDE" TYPE="ntfs"
/dev/mapper/nvidia_fcacbeib2: UUID="4344165e-07c3-4da6-b640-da9bf964a74e" TYPE="swap"
/dev/sda: TYPE="nvidia_raid_member"
[code]....
I'm thinking the problem may be in my grub device.map file, which only lists the SATA raw device aliases, but I may be completely wrong:
twescott@latitude:~$ cat /boot/grub/device.map
(hd0) /dev/sda
(hd1) /dev/sdb
View 5 Replies
View Related
Nov 29, 2010
I have kuduz installed but am wondering if there is a way to probe hardware with Fedora without having to reboot? Ioscan command is not found in my terminal and I can't find it in my Package Manager or a RPM search. A GUI version would also be of interest but not mandatory.I'm a Mandriva defector that is wheening off of Drake Tools.
View 2 Replies
View Related
Feb 11, 2011
I just built some machines with the Intel 82574L gigabit ethernet chip, loaded Fedora 14, and discovered a problem with the e1000e driver dying after a few minutes. A little time spent perusing the web told me that the same driver had problems in Fedora 12 and Fedora 13 as well. Congrats to Fedora for the hat trick.As of kernel 2.6.35.10-74.fc14.x86_64, e1000e driver 1.0.2-k4 still had bugs.[URL]
View 6 Replies
View Related
Mar 28, 2009
while iam installing centos 5.2 i am getting following error :
LVM Operation failed vcreate failed for <fsset.partition device instance at 0xb7C1ef6c>
View 1 Replies
View Related
Apr 16, 2009
I received my dedicated server, and I was thrilled to work on it! After a while I encountered many, many problems, and most of them are fixed now.
However, I've been stuck on a LUA problem for hours now...When I check all files (/reconfigure) I get this error;
View 13 Replies
View Related
Aug 19, 2010
I am attempting to write an rpm for railo-resin server. To the best of my knowledge the rpm is written correctly, however when I run "rpm -ivh rail-x.x.x.rpm" I get the following error.
Quote:error: Failed dependencies:
libodbc.so is needed by railo-3.1-2.i386
libodbcinst.so is needed by railo-3.1-2.i386
View 7 Replies
View Related
Mar 31, 2010
When the RPM runs it come up with this error. How do I install the required dependencies? I have added more repositories, but still there are a few dependencies missing. Is there a zypper/sudo -get or something available? Opensuse 11.1 Gnome
[code]...
View 4 Replies
View Related
Oct 26, 2010
I do encounter when I try to install this file:
[root@mypc]# rpm -ivh sysstat-7.0.2-3.el5.i386.rpm
warning: sysstat-7.0.2-3.el5.i386.rpm: V3 DSA signature: NOKEY, key ID 37017186
error: Failed dependencies:
libc.so.6(GLIBC_2.4) is needed by sysstat-7.0.2-3.el5.i386
rtld(GNU_HASH) is needed by sysstat-7.0.2-3.el5.i386
Also when I try this also not work
# yum install sysstat
-bash: yum: command not found
However the os and email server working fine on it. What should I check and try it.
View 4 Replies
View Related
Apr 7, 2011
I am recently getting a very weird error on my Webmin. The result of this problem I suspect is I am no longer able to log into my Maia Mailguard which is my Spam Viewer.
Quote:[BEGIN failed--compilation aborted at (eval 17) line 1.
restarting miniserv
[06/Apr/2011:23:34:09 -0400] Restarting
[06/Apr/2011:23:34:10 -0400] miniserv.pl started
[06/Apr/2011:23:34:10 -0400] Perl module Authen::PAM needed for PAM is not installed : Can't locate Authen/PAM.pm in @INC (@INC contains: /usr/libexec/webmin /usr/lib/perl5/site_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl /usr/lib/perl5/vendor_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.8 /usr/lib/perl5/vendor_perl /usr/lib/perl5/5.8.8/i386-linux-thread-multi /usr/lib/perl5/5.8.8 .) at (eval 17) line 1.
BEGIN failed--compilation aborted at (eval 17) line 1.
Failed to initialize SSL connection
Failed to initialize SSL connection
View 3 Replies
View Related
Jul 26, 2011
I been tryin to install httpd-devel on Centos 5 with plesk i keep gettin Missing Dependency errors i went to url
and got attached packages but they give me this error
Code:
# rpm -ivh httpd-devel-2.2.3-45.el5.centos.1.x86_64.rpm Failed dependencies:
httpd = 2.2.3-45.el5.centos.1 is needed by httpd-devel-2.2.3-45.el5.centos.1.x86_64
Code:
yum install httpd-devel
Loaded plugins: fastestmirror, priorities
Loading mirror speeds from cached hostfile
code....
View 5 Replies
View Related
Jun 23, 2009
I am a newbie trying to install XMLSec on my server. I have CentOS 5 with OpenSSL 0.9.8b. I downloaded xmlsec1-1.0.3-1.i386.rpm from [URL]. While doing rpm -Uvh xmlsec1-1.0.3-1.i386.rpm I get the following error message.
error: Failed dependencies:
libcrypto.so.4 is needed by xmlsec1-1.0.3-1.i386
libxml2.so.2 is needed by xmlsec1-1.0.3-1.i386
libxslt.so.1 is needed by xmlsec1-1.0.3-1.i386
I also downloaded RPM's for libxml2 and libxslt from ftp://xmlsoft.org/libxslt/ but each package give further errors rpm -Uvh libxml2-2.7.3-1.x86_64.rpm warning: libxml2-2.7.3-1.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID de95bc1f error: Failed dependencies: libxml2 = 2.6.26 is needed by (installed) libxml2-python-2.6.26-2.1.2.7.x86_64
and
[Code]....
View 1 Replies
View Related
Apr 20, 2011
I have a problem with GPG key, when I tried to run #yum updateI have got this errorwarning:rpmts_HdrFromFdno: Header V3 DSA signature: NOKEY, key ID d05c057cGPG key retrieval failed: [Errno 14] HTTP eRROR 404: Not foundI used Centos 5.5.
View 10 Replies
View Related
Jun 17, 2011
I had a LiveUSB of CentOS 5.5, so I decided the install it.With no installer,I just copied the files to my hard drive.his was in a multi boot with Windows 7, Ubuntu 9.10, and FreeDOS.I updated GRUB2 and it detected CentOS. I loaded my entry and it failed to mount the root filesystem.I took the initrd0 file from the LiveUSB syslinux folder and added that ramdisk to the entry. Now it finds the root filesystem (/dev/sda9 as Ext3).But it fails shortly after loading /sbin/init. It talks about an init error where it says "File not found!!!".The previous lines involved umounting old filesystems, like /dev.
View 4 Replies
View Related
Aug 30, 2011
Our server is a x86_64 centos 5.5 computer. we installed samba3x-3.5.4-0.70.el5_6.1.x86_64.Samba seems work fine, we don't notice any problem in using it. But in the workstation log file, there are a lot of error messages like:
[2011/08/26 14:37:57.682260, 1] smbd/service.c:678(make_connection_snum)
create_connection_server_info failed: NT_STATUS_ACCESS_DENIED
[2011/08/26 14:37:58.194394, 1] smbd/service.c:678(make_connection_snum)
[code]....
View 2 Replies
View Related
Aug 8, 2010
I need to know I/O stats per process. When executed dstat give the bellow error message.
dstat -M topio -d -M topbio
Module topio failed to load. (No module named dstat_topio)
Module topbio failed to load. (No module named dstat_topbio)
CentOS release 5.3 (Final)
uname -r => 2.6.18-128.2.1.el5
How to resolve the above error message
View 2 Replies
View Related
Aug 26, 2009
when ever i give yum update am geting this error. failed to use search generator: failure:repodata/318b9912817ec3309c6defc47d79e878c52a21fd1457d191bb ff060fdb7f7f8d-primary.sqlite.bz2 from rpmfusion-free-updates: [Errno 256] No more mirrors to try. I was trying to install tomcat using yum. Is there any way i can install tomcat other than yum utility. I downloaded he zip folder for tomcat which i downloaded from apace tomcat site.
View 2 Replies
View Related
Feb 20, 2010
I'm a recently proud owner of a new Aspire AS3810T with Fedora 12 installed, when it boots up before entering the boot screen when it loads I see this error message:IOMMU: Mapping reserved region failedHow can i fix this error? It's quite frustrating
View 2 Replies
View Related
Nov 1, 2010
I have wordpress server running on my machine and I have SELinux enabled for enforcing/targeted. I am unable to insert images, music, etc from the add new post field on the wordpress dashboard. I receive the following error:
image.jpg has failed to upload due to an error The uploaded file could not be moved to /var/www/html/wordpress/wp-content/uploads/2010/10. When I disable SELinux completely, it works fine. Does anyone know what Boolean I need to check to resolve this issue?
View 4 Replies
View Related
Jan 28, 2011
When I send mail via Evoultion it does seem to send ok but still the following error message comes up: Error while sending message. Failed to append to : Unknown error Appending to local 'Sent' folder instead. Not sure what's up with that but thought I would mention it.
View 3 Replies
View Related
