I have a lenovo 7757 model which has an inbuilt camera. I have FC9 working on it. However I cannot use the camera. How do I enable it? If someone could point me to a driver if it needs to be installed.
View 6 RepliesI have installed opensuse 11.4 in my lenovo ideapad G460. But, I am not being able to make the inbuilt microphone work. It does not record anything and also does not work in skype. I am not that expert with linux. I looked at different posts in this forum regarding microphone detection problem, bit could not follow. How to setting up my inbuilt microphone?
View 6 Replies View RelatedI am new to Linux, and have started using Ubuntu 9.10. everything seem to be in place except for the Web Cam. i think it is not being identified by my OS. i have tried Ekiga, but still of no use. i am using a Compaq Laptop with an inbuilt camera.
View 1 Replies View RelatedI run Ubuntu 10.04 on a Sony FZ-VGN15C Laptop. On start-up of Ubuntu I get two error messages including '...Video : Failed...' (the message is too fast to be read completely) This might relate to the fact that my built in camera does not work with Skype or Cheese Webcam Booth. The webcam type is VGP-VCC4 by RICOH.
View 4 Replies View RelatedI use a modem which is not on fedora inbuilt list. I need to give linux a shot. what is my work around.
View 1 Replies View RelatedI was looking to iphone and i was surprised the quality of such tiny camera.
Is there any alternative camera for my laptop to have similar or much better then the one in iphone? So that i can use it from my laptop, but have very sharp HD quality with maximum megapixel + highest frame per second.
How to recompile squid under fedora 13 to insert this arguments ---> --enable-storeio=diskd,coss
View 2 Replies View RelatedI recently installed Deluge 1.2.0 from the following PPA:[URL]I using this on two different Linux computers. One is running Linux Mint 8 and the other is running Ubuntu Netbook Remix 9.10. The first time on either computer when I enable WebUI in the Deluge GUI it works fine. However if I ever disable it in plugins section I am subsequently unable to re-enable it (doesn't appear in the side panel again). Rebooting or reinstalling Deluge seems to have no effect.Is this a bug or am I doing something wrong?
View 3 Replies View RelatedI loaded Fedora 10 onto my Lenovo T60 last week. everyday i boot it up and it works fine for a few minutes, then freezes. to the point of powering off. my mouse still works but nothing else. i power back up and it generally stays up after that.
Before i had Fedora i was useing PCLinux 2009 and it worked just fine. i get a kernel error alert every once in a while. i finally submitted it to Fedora to be reported. also a flash plugin says it is needed at times but most media plays.
Is there something i'm missing here? like i need to add an additional update? i already updated/installed most Fedora 10 updates.
I have problems installing Fedora 14 on my netbook, is a Lenovo S10-3, model 0647FDS (Atom N550, 2gb DDR3, etc). When the installation program starts, hangs at "Initalizing network drop monitor service"
View 7 Replies View RelatedI'm trying to install Fedora 15 on my Lenovo S10-2 netbook, using a USB drive I created with LiveUSB-creator, as suggested. The creation of the USB drive works fine, but when I try to boot from it on the Lenovo, I get cryptic error messages :ERROR : idle with IF=0 -- and then some misc. error codes.I have no idea what this means or how to progress from here
View 2 Replies View RelatedI m new to linux. I have fedora 14 on my lenovo 3000 n100 machine but thr is no sound at all. I have tried all the possible solution but no success at all. My alsa profile is [URL].
View 9 Replies View RelatedI use g edit to write my C++ codes. How can I know the inbuilt library functions of C++?
View 4 Replies View RelatedI am going to set up a Ubuntu installation on an external USB drive as per CS Cameron's advice in[URL]..I will put home on a separate partition and encrypt it when I reinstall Ubuntu using the inbuilt encryption in Ubuntu 10.04. (My data will be on there so it should be safe for a short while if the disk goes missing)
My question is: If I plug the USB drive into another computer which runs ubuntu (but cannot boot from USB), will ubuntu running in the "normal" way installed on the local fixed hard drive, be able to access the data on the partition if i tell it the password?
My Ubuntu 10.04 will not detect the inbuilt webcam on my Compaq Presario CQ61 laptop computer. This laptop only runs Ubuntu as I removed Windows when I got it home new from the shop a few years back. Haven't tried to get the webcam working until now. I have downloaded "Cheese" and when I run it I get the message No Device Found.I have also tried gstreamer-properties in a terminal and get the message video for linux 2 (v4l2): Cannot identify device '/dev/video0'
is it a lost cause to get my webcam working?
I have got a refurbished acer aspire one with linpus linux...now
1. the mozilla firefox browser seemed pretty much old...but if I try to download a new version it comes us as a zip file...
2. same to microsoft docx...they come as zip file...can not sort out the updating of the browser, can not download docs files...
3. also the desktop is a very handy, but unattractive looking one...how can I get a desktop customize by my own?...
4.the inbuilt messanger is not taking any id except the one from gmail.
I am interested to know how to port usb driver in linux...I am having the driver code ..I am using fedora 11. So before that I want to know how to delete the usb driver that comes with installation or inbuilt driver. After that I will try to port my driver code and check whether the driver is working or not.
View 4 Replies View RelatedAfter I upgrade fedora from 14 to 15 on thinkpad T510, it takes a long long time to boot up@~~~ .I look at the boot up prompt, it just stuck at the network service part.... for about 4 minutes!!!I followed thread url.
After I did
# echo "options iwlagn 11n_disable=1" >/etc/modprobe.d/Intel-80211n.conf
# reboot
I am able to use my wireless now, but when fedora15 is boot up, it does not auto connect for me, I need to connect the wireless myself.
Here is what I find. During bootup, it stuck at Network service part for around
[fanw@f14 ~]$ systemctl list-units --failed
UNIT LOAD ACTIVE SUB JOB DESCRIPTION
network.service loaded failed failed LSB: Bring up/down networking
sssd.service loaded failed failed System Security Services Daem
LOAD = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
code....
I bought a thinkpad Edge 13" with AMD CPU (NV338) and installed f15 on it. First boot : no WiFi...
Code:
lspci -n
...
08:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:0576] (rev 01)
14e4:0576 is actually BCM43224 broadcom chip, supposed to work with broadcom-wl driver (non-free...)
So I installed broadcom-wl + kmod-wl, reboot, check if it really get installed :
Code:
lsmod | grep wl
wl 1954479 0
lib80211 4103 1 wl
Ok but... no WiFi interface visible... Few dmesg :
Code:
dmesg |grep radio
[ 22.289176] thinkpad_acpi: radio switch found; radios are enabled
[ 22.310166] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is blocked
(wifi toogle seems not working btw)
[code]....
I installed Ubuntu 10.04.2 LTS version in to Asus eeeTopET1610 PT PC. It has the following sound card configuration:
Sound Driver:3.8.1a-980706 (ALSA v1.0.23 emulation code)
Installed drivers:
Type 10: ALSA emulation
Card config:
HDA Intel at 0xfbbf8000 irq 29
Audio devices:
0: ALC887 Analog (DUPLEX)
Synth devices: NOT ENABLED IN CONFIG
Midi devices: NOT ENABLED IN CONFIG
Timers:
7: system timer
Mixers:
0: Realtek ALC887.
There is no audio output coming from the inbuilt speakers. when headphone is connected, audio is available with headphone. But not with the internal speaker when headphone is not connected.
in an attempt to get me less radioactive i have put my lappy on a desk not on my lap. it is a little way from me so i need to do 800x600 resolution so i can read comfortably. the fedora install i have (vista copes ok) only shrinks down the screen to 800x600 when i choose this screen mode. i really need 800x600 fullscreen.
View 1 Replies View Relatedrecently installed fedora 14 on my lenovo ideapad y530.
Linux bardot 2.6.35.9-64.fc14.x86_64 #1 SMP Fri Dec 3 12:19:41 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux
here is my audio device:
lspci | grep Audio
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
it has surround speakers and even a subwoofer. unfortunately only the two side speakers work. how to make ALL my speaker system work?
I am keen to get the internal modem working on my notebook, so I can set up faxing and dial-up internet access.
I have failed to get it working by using the Linuxant alsa-driver-linuxant and hsfmodem packages, but that may be because I am doing something wrong.
alsamixer on my system tells me I have CARD: HDA Intel and CHIP: Analog Devices AD1984.
I have these devices in /dev, which appear to be candidates for modem operation:
Code:
[doug@cardraeh Modem]$ ls -l /dev/ttyS*
crw-rw---- 1 root dialout 4, 64 Apr 16 11:40 /dev/ttyS0
crw-rw---- 1 root dialout 4, 65 Apr 16 11:40 /dev/ttyS1
crw-rw---- 1 root dialout 4, 66 Apr 16 11:40 /dev/ttyS2
crw-rw---- 1 root dialout 4, 67 Apr 16 11:40 /dev/ttyS3
[Code].....
I've been running wubi for about 2 weeks now, and am completely new to all this. Everything was running fine, until yesterday when I restarted my laptop and the sound died. It had been working fine before, but now no sound comes out of the inbuilt speakers. However, the sound works perfectly through my headphones. Am running 11.04 on an Inspiron 1525, I don't know what other information you need, so if you ask me I'll try and find it. Also the sound works fine in Windows.
View 9 Replies View RelatedWhile I was exploring my newly installed Mandriva Linux 2010 in my system, I found some emoticons somewhere in a window ( I exactly don't remember where ). I want to know where to use those emoticons or what are the uses of those emoticons. Please give me an example. If possible also please tell me where I could find that emoticons i.e. in desktop settings or somewhere else. I forgot the location.
View 2 Replies View RelatedI recently installed skype on my rhel 6.0, 64 bit. But the problem is, my mic doesn't work. The sound comes out through the speakers of my Toshiba laptop even though my external mic is plugged into the mic ports. I can hear the other end (from the computer's speakers not from the head set of the mic) but the other end can't hear me. I went to system preference, sound, input and nothing is muted and when i talk through the mic the input level bar doesn't move. I typed arecord --list-devices and lsusb and i got the following results. Can anyone tells me what to do to get my mic works? Note that i use windows 7 on the othe partition and the mic just works fine.
View 3 Replies View RelatedI have a Lenovo thinkpad T400 with Vista x64 that I want to dual-boot with fedora 10. The T400's original config has 3 primary partions:
1) Vista boot partition (some weird partition that it only uses to boot... this is my first time using Vista so I don't know the details, but I think it has to be there and it has to be a separate partition from the "data" partition)
2) Vista data partition
3) Lenovo Rescue and Recovery partition (a separate bootable partition that is used for recovery, backups, ...)
My first attempt was to shrink the recovery partition and add a new extended partition that has the two standard fedora logical volumes and an extra NTFS to be shared between the OS's (I usually use FAT32 for this one, but NTFS support seems to be pretty solid now).
Everything was fine, but I couldn't boot into the rescue partition. According to this site:
[URL]
You *have* to have a linux boot partition be your primary partition. Other people have told me the same thing and that site has an explanation, but I don't get it =)
So, it seems that I need 5 primaries (3 original vista/lenovo primaries, 1 linux primaray to put the boot stuff into, and 1 extended for everything else) to make this work (which is not possible). Can anyone think of something else I could do (other than getting rid of Vista and the Lenovo stuff and giving them both the finger?) I'm thinking maybe I could make an extended partition and move one or more of the Vista/Lenovo partitions in there, but I'm not sure if they could boot.
I have at office dual booting Fedora14 + Windows 7 in Laptop Lenovo G550. I am using it regularly for work. Recently it stopped normal shut down. It showed some panic message first time and i have to force shut down.It boots normally. Now it does not give any message during Shut down but it does not shut down properly. Every time i have to force shut down.I am ready to follow instructions from forum members. I want to know that how much serious this panic is. Will it result in corruption of installation?
View 5 Replies View RelatedI just put Fedora 11 on my Lenovo Thinkpad t400. I selected the integrated (lousy, but Intel (supported)) graphics device in the BIOS, but I really hate the lower performance than the discrete graphics device. However, this device requires fglrx or radeonhd for DRI. RPMFusion has not released an (a)kmod-fglrx, so I can't use that. I have heard radeonhd has some stability issues though, and I don't know how to install. I was wondering how I could completely change my graphics configuration (change chipsets in the BIOS) and get the X Server in Fedora 11 working with the new driver and chipset. Is it a good idea to use radeonhd, or should I wait for the fglrx?
Even then, how would I completely change my graphics configuration so it would work with a different card & driver? I don't want to do a fresh install because I've done a lot of work & customization with the F11.I don't know anything about radeonhd, so any information about this kind of thing would be useful.Finally, should I just suck it up and deal with the Intel graphics? Is anything of this sort really worth my time? (I'm willing to spend quite a bit, trust me!)
I have a compact-flash card that has some corruptions. I woiuld like to try to fix this by copying out the data from the flashcard using ddrescue or something and then trying to fix the filesystem outside the flash.
BUT Fedora does not allow me to really mount / make a block device of the usb-device, so I can not use ddrescue to copy out the disk-image.
Why is my Nikon camera not a block device, and then the other "GUI-applications" triggered on that device in stead?