Fedora Hardware :: Lenovo Thinkpad Edge And BCM43224?
Jul 28, 2011
I bought a thinkpad Edge 13" with AMD CPU (NV338) and installed f15 on it. First boot : no WiFi...
Code:
lspci -n
...
08:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:0576] (rev 01)
14e4:0576 is actually BCM43224 broadcom chip, supposed to work with broadcom-wl driver (non-free...)
So I installed broadcom-wl + kmod-wl, reboot, check if it really get installed :
Code:
lsmod | grep wl
wl 1954479 0
lib80211 4103 1 wl
Ok but... no WiFi interface visible... Few dmesg :
Code:
dmesg |grep radio
[ 22.289176] thinkpad_acpi: radio switch found; radios are enabled
[ 22.310166] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is blocked
(wifi toogle seems not working btw)
[code]....
View 3 Replies
ADVERTISEMENT
Sep 16, 2010
Recently I got a lenovo laptop and installed opensuse 11.3 from live usb distribution, well the issue is when I want to listen to some music and plug in my headphones, the laptop speakers do not turn off automatically.
View 9 Replies
View Related
Jan 19, 2011
Slackware 13.1 installed clean on a new ThinkPad Edge (version 13 inch with AMD Processor and ATI graphics). I can get most of what I want working fine except for suspend and resume. I read somewhere that I should be using generic rather than huge kernel, so I have done that and scrapped ATI proprietary driver in case that was causing problems, but nothing so far has allowed me to suspend and resume with pm-suspend, acpitool suspend or with KDE suspend command. In all cases the screen blanks and the single ThinkPad red LED goes from on to blinking, but nothing seems to wake the machine up again. I had both suspend and hibernate working fine with Slack 13.1 on an older Lenovo laptop and ubuntu users report on their forums that this laptop does suspend and resume "out of the box" so I feel it must be possible.
View 4 Replies
View Related
Oct 30, 2010
I have a Thinkpad edge. I am travelling right now, and will be for the next 2 weeks, and just discovered that my thinkpad's internam microphone won't work. Plugging in an external one won't work either.This means that I won't be able to communicate with friends & family for 2 weeks... any help to patch this problem will be IMMENSELY welcome.
Symptoms are strange: I can go to Sound Preferences, select Analog Stereo Duplex as hardware, click on "Input", change the input volume, mute it, unmute it... everything works fine. However, if I tap against the mike, the input level bit doesn't move at all. Needless to say, nothing sees it.
Here is the output of the ALSA Information script... which looks like greek to me! Help...
!!################################
!!ALSA Information Script v 0.4.59
!!################################
!!Script ran on: Sat Oct 30 13:28:44 UTC 2010
!!Linux Distribution
[code]....
View 9 Replies
View Related
Apr 13, 2011
I am trying to use my accelerometer as joystick just so I know it's working, but I can't figure out how. To my surprise, Ubuntu doesn't seem to have a nice GTK joystick testing dialog. There used to be hdaps-gl out there for testing, but this was for very old models and is only released for Ubuntu 8.04 afaik. So I tried installing neverball for that purpose. It doesn't have options for joystick selection, but apparently it works out of the box with a Thinkpad T61.
Code:
sudo aptitude install tp-smapi-dkms
sudo modprobe tp_smapi
sudo modprobe hdaps
dmesg:
Code:
[720.093604] thinkpad_ec: thinkpad_ec 0.40 loaded.
[720.095348] tp_smapi 0.40 loading...
[720.095786] tp_smapi successfully loaded (smapi_port=0xb2).
[842.860767] thinkpad_ec: thinkpad_ec_read_row: failed waiting for data: (0x13:0x00)->0xfffffff0
[842.860773] hdaps init failed at: hdaps_get_ec_mode failed
[842.861321] input: ThinkPad HDAPS joystick emulation as /devices/virtual/input/input10
[842.861696] input: ThinkPad HDAPS accelerometer data as /devices/virtual/input/input11
[842.861883] hdaps: driver successfully loaded.
lsmod:
Code:
Module Size Used by
hdaps 10772 0
tp_smapi 26194 0
thinkpad_ec 5842 2 hdaps,tp_smapi
(..)
I've also tried to use jstest with
/dev/input/js[0|1]
and
/devices/virtual/input/input10/[many things]
But the former gives static 0 for both axes and the second gives error messages (you're probably not supposed to use it like this).
View 3 Replies
View Related
Aug 19, 2015
I tried to install Debian 8.1 on Lenovo Edge 125, but on stage ''detecting network hardware' of install process my laptop stopped and froze, so I don't know what to do. (Previously I've installed Debian 6 or 7 on this laptop and every thing was OK).
View 6 Replies
View Related
Oct 5, 2010
See attached photo. Is my screen broken or what?
View 5 Replies
View Related
Feb 9, 2011
I have a pretty new Lenovo Thinkpad L412, with Ubuntu 10.04 LTS. I can't log in to any wireless network (I have dual boot with Win 7 and it works there). The available networks shows up in the list but I can't connect them, "no network connection" it says.
View 3 Replies
View Related
Dec 7, 2010
Im considering installing Open Suse linux on my laptop - Lenovo Thinkpad T510i. Will all the devices be recognized?
View 2 Replies
View Related
Jun 29, 2010
I am sorry if this seems long I tried to only list the information I thought was pertinent to my wireless issue. I do get 2 of my neighbors wireless networks to show up but mine does not and it has the strongest signal by far. I have 3 other computers connected to it also on Ubuntu 10.04 LTS
lspci -nn | grep Realtek
03:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8172] (rev 10)
iwconfig wlan0
wlan0 802.11bgn Nickname:"rtl8191SEVA2"
Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated
Bit Rate:300 Mb/s
[Code]...
View 1 Replies
View Related
Jul 9, 2010
I'm trying to choose between the Lenovo Thinkpad W500 and the older T61p. The W500 is said to have a higher quality display than the T61p, however there seem to be more problems with running Linux on it. One of the reasons for this is the fact that it has switchable graphics, with one of the GPUs being an ATI FireGL. The older T61p comes with Nvidia Quadro FX only, which as we know is more Linux-friendly.
Which model should I choose? Will certain issues such as being able to suspend / resume be cleared up with newer kernel releases?
View 8 Replies
View Related
Aug 27, 2010
I have Centos 5.5 running on this laptop but can't get gobi_loader(loads firmware onto the 3g device and then you can use wvdial) working on kernel 2.6.18-194.11.1.el5 (x86_64). lsusb shows the Gobi device but gobi_loader uses /dev/ttyUSB0 which doesn't exist.
View 18 Replies
View Related
Aug 12, 2010
The only thing really missing from this install is this issue with the sound. I've searched all over the forums and i found one thing where you get the model and codecs and write them to a file, however, I can't seem to find what my "model" is because none of the postings have anything about Lenovo laptops. Here is the command they all asked for:
Code:
With that info, how do I get the model, and how do I get my speakers to stop playing when headphones are plugged in. Also, I don't have any software installed like pulse audio either, so it's not that.
View 1 Replies
View Related
Nov 27, 2010
I've just joined the linux gang(or I am trying to) I have
-downloaded desktop/netbook edtion
-burned to dvd using infrarecord
-changed bios settings to boot from cd
-didn't work
-used the override feature that gives a bootlist at splash screen but cd drive not listed so I assume the cd is not recognised as a boot disk
-tried the usb/cd maker that comes with in the rar but its looking for the cd image...an .iso file, but I can't find one in folder.
ubuntu says I can run a trial from the cd alongside vista but when I open the executable it just offers intall, no try and if selected starts to install I think I can do the partition thing if I have to but I don't want any vista running on my machine.
View 7 Replies
View Related
May 8, 2015
I run Debian with Gnome on a beat up workhorse ThinkPad. I upgraded to Jessie last week with just one issue. Before the upgrade, I could plug in a USB drive (I use a couple of WD MyPassports most often) and they would mount, read, and write without a hitch.
Since the upgrade, when I plug in a USB drive, the file manager (3.14.1) sees the drive, but when I click on the drive to access/mount it, I receive a dialog box reading: Oops! Something went wrong. Unhandled error message: Error when getting information for file '/media/user/MyPassport1': Input/output error.
If I hit the little “eject” button in the file manager, then mount the drive as root from a command prompt [e.g., mount -t ntfs-3g /dev/sdb1 /media/external] I can run a directory of the drive, but ls -l /media/external fails. From the command prompt I am unable to perform reads or writes to the drive.
Rebooting into recovery mode (i.e., without Gnome), I get the same behavior with CLI messages reporting I/O errors with the drive. I can run a directory, but ls -l, reads, and writes fail.
This behavior is the same on all three USB ports. It is not limited to these MyPassport devices.
The drives work flawlessly on another headless machine upgraded to Jessie the same day. And on another still running Wheezy.
If I boot the ThinkPad from a live CD (Mint 14, I believe) the USB drives mount, read, and write fine.
My BIOS is up to date, 1.52.
lspci -v says this about USB ports:
Code: Select all00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at 1880 [size=32]
Capabilities: [50] PCI Advanced Features
Kernel driver in use: uhci_hcd
[Code] .....
View 4 Replies
View Related
May 31, 2011
I have an HP 5101 mini notebook. It used to run quite happily under Fedora 14 after running yum kmod-wl-PAE .
Fedora 15 seems to not have any simplistic solutions. I am confused by rebuidling the kernel and would like a simpler solution if possible.
Here is the lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
[Code].....
View 4 Replies
View Related
Jun 13, 2011
I'm having all sorts of problems with my wireless connections in an HP Pavilion DM1. I'm sure it was working last week. I have two access points, one with WPA, one unsecured. It's not working with either. I can connect to both of them fine with a wifi USB adapter.
I've tried:
Using Wicd instead of networkmanager
Using the proprietary driver
Installing the linux-firmware package from Oneric (version 1.54)
Changing the frequencies the AP runs on
[Code]...
View 3 Replies
View Related
Oct 28, 2010
I put together a little computer recently to hook to a TV.The problem I'm having is that when I start the computer up and get to the desktop... the desktop is off the edges of the screen. I checked the resolution and it's 1920x1080.I can't see the panels my applications menu, as they're both off the edge of the screen. Is there anything that can be done to correct this? Also, the TV has no settings to correct this problem.
View 2 Replies
View Related
Nov 22, 2009
I noticed a problem when editing files with nano. This problem happens if the terminal window that I run nano from is not wide enough to show the full line.By way of example below is part of my grub.conf
Code:
title Fedora (2.6.31.5-127.fc12.x86_64)
root (hd0,13)
kernel /boot/vmlinuz-2.6.31.5-127.fc12.x86_64 ro root=UUID=47e4c448-8087-4ec6-a67b-814845a598db noiswmd LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us vga=0x370 nouveau.modeset=0
initrd /boot/initramfs-2.6.31.5-127.fc12.x86_64.img
If we assume the code box above is the size of the terminal window, if I edit anything past what will show as the $ sign in nano, it will automatically add a carriage return. So if we take the kernel line above, if say the screen shows at the end root=UUID=$, if say I were then to add 00 the end of the UUID, it will move everything starting from root=UUID= to a new line. Is there some wrap feature that is enable in Fedora for nano?
View 7 Replies
View Related
Jun 8, 2011
First, I upgraded to F15. All went smooth. No problem. But if I pull up a terminal in KDE via menu->utilities->Terminal, I get a terminal that shows only 3 lines. If I try to increase the size by pulling the edge it locks up the computer. Functions otherwise. This is Gnome Terminal 3.0.1. X terminal works fine. So does Konsole. But not the above application from the menu.
View 5 Replies
View Related
Jul 14, 2011
I'm trying to compile the bleeding-edge compat-wireless because I know there are some ath9k fixes in it because I use in on my Debian and Ubuntu machines; however, when I try and run make, I receive this error:
Code:
make: *** /lib/modules/2.6.38.8-35.fc15.i686/build: No such file or directory. Stop.
make: *** [modules] Error 2
[code]....
View 2 Replies
View Related
Aug 31, 2009
I need to setup a Intel Xenon power edge 1900 server, which fedora version (10 or 11) suits it best and whether I should go for 64bit or 32bit (If I go with 64 bit some applications wont support it). I also have another issue, currently on another Intel Xenon power edge 1900 server on which Fedora 9 32bit version is installed, tough the server has 8GB ram, fedora can access only 3.2 GB. How can I solve this issue and will it repeat in the new server where I install fedora(10 or 11).
View 1 Replies
View Related
Mar 9, 2010
After the update on 7/03/10 edge+mouse button combo's don't work anymore, keyboard short cuts for the same function are still working. Example "Scale", keyboard short-cut ctrl-s working, edge+mouse button Right Edge - Right Mouse Button no action. Worked before...
View 6 Replies
View Related
Jun 2, 2011
I've recently installed F15 on my old thinkpad X41 to give it a go after sticking to ubuntu for quite a bunch of years now.
Somehow there seems to be a problem with the installation tho: the screen freezes up (as does the keyboard) after a while using it - not many programs open, a couple of workspaces enabled, no memory or CPU stress whatsoever - and all i'm left with is a moving mouse cursor. Ctrl + alt + F2 doesn't work and the only solution is to restart the laptop again.
Tried the fallback mode and same thing still happens, so maybe its not a graphic card issue.
View 1 Replies
View Related
Aug 16, 2009
I have been trying on and off for over 6 weeks to upgrade from fc10 to fc11. I keep getting the problem where Anaconda cannot format the HD. I originally downloaded the image and it fails when trying to format the fs even if I leave the original fc10 fs in tact I then used the LXF DVD and got the same problem.
I have tried both upgrading and new installs from an fc10 HD but it still fails to format.I have also tried formatting using fc10 (ext3) and have just read if I am using a live CD it must have an ext4 partition on it, but I assume it should be OK with the LXF DVD?I have been using Fedora for over five years now but if I cannot resolve the problem soon I will have to reluctantly change my OS, but before resort to doing this, could someone point me to any information that might help me to resolve the problem?I did try manually partitioning using gparted and ext3 without LVM but that also fails.
View 2 Replies
View Related
Oct 10, 2009
I loaded Fedora 10 onto my Lenovo T60 last week. everyday i boot it up and it works fine for a few minutes, then freezes. to the point of powering off. my mouse still works but nothing else. i power back up and it generally stays up after that.
Before i had Fedora i was useing PCLinux 2009 and it worked just fine. i get a kernel error alert every once in a while. i finally submitted it to Fedora to be reported. also a flash plugin says it is needed at times but most media plays.
Is there something i'm missing here? like i need to add an additional update? i already updated/installed most Fedora 10 updates.
View 6 Replies
View Related
Mar 8, 2011
I have problems installing Fedora 14 on my netbook, is a Lenovo S10-3, model 0647FDS (Atom N550, 2gb DDR3, etc). When the installation program starts, hangs at "Initalizing network drop monitor service"
View 7 Replies
View Related
Aug 30, 2011
I'm trying to install Fedora 15 on my Lenovo S10-2 netbook, using a USB drive I created with LiveUSB-creator, as suggested. The creation of the USB drive works fine, but when I try to boot from it on the Lenovo, I get cryptic error messages :ERROR : idle with IF=0 -- and then some misc. error codes.I have no idea what this means or how to progress from here
View 2 Replies
View Related
Mar 2, 2009
I have a lenovo 7757 model which has an inbuilt camera. I have FC9 working on it. However I cannot use the camera. How do I enable it? If someone could point me to a driver if it needs to be installed.
View 6 Replies
View Related
Feb 14, 2011
I m new to linux. I have fedora 14 on my lenovo 3000 n100 machine but thr is no sound at all. I have tried all the possible solution but no success at all. My alsa profile is [URL].
View 9 Replies
View Related
