OpenSUSE Network :: Continued Inability To Get On Line Wireless Network
Jul 30, 2011
Presently have installation of 11.3, win 7, and Ubuntu 10.04 in a multiple boot. Win 7 and 10.4 are connected wirelessly, no problem getting on line.I know little or nothing about wireless as I created a network in win 7, installed Ubuntu and it recognized my network immediately and I was on line effortlessly Suse was a first choice and its been on my HD a while with no access. So this will be my last shot to gain some insight to getting it on line.
I just started using OpenSUSE on an old laptop. It seems that I have my graphical problems at least temporarily solved, but I continued to lose my wireless connection after an hour of use. This is an old and well supported chipset (RT2500) and I had never had any issues with it before. I use WPA security, and one kind poster suggested I had a line for using the old "wext" driver in the /etc/sysconfig/ifcfg-wlan0 file, and that seems to have sorted it since I have not had any further issues since doing that edit. I eventually found the information on my own:
# Note: This option requires a wpa driver supporting it, like # the 'nl80211' driver used by default since openSUSE 11.3. # When you notice problems with your hardware, please file a
After installing 11.4, I need to type in the command to update the firmware for a broadcom wifi adapter. Then I needed to reboot, twice, before the system knew to use the adapter (where the adapter wifi light goes from orange to blue).
Then I needed to add my wireless network and type in my key. But the key does not take. If I click on my wireless network icon, it just re-asks for the key and does not connect nor give any other message. Network icon continues to display no connection.
So I need to reboot again.
When the system starts again, the adapter is blue, I click on the icon for my wifi network and it connects without asking for my key and I can then set to start my wifi by default.
I recently installed OpenSUSE 11.2 and everything works fine except wi-fi card, of course. The problem is that after installation the system recognized the card (is was listed in network devices in Yast) but I was unable to enable it through network-manager applet. Though the device could make scanning through terminal (found article in docs but didn't fully understand wpa_gui). Then i was stupid enough to delete the device from Yast list to try to reinstall it. So the problem is that i simply can't do this cause i see no way to re-detect. That is the goal is to at least turn back to post-install system state and try to enable wifi card again.
When I attempt to connect to a wireless network, the network manager asks me for the network's password, then says 'setting network address' for 20 or so seconds, then asks me for some random Hex or ASCII key in the same type of window I put the password in (Secrets for Noel -- KDE Daemon). Since a key is already typed into the window, I press OK, which then causes the network manager to go back to 'setting network address', then the window pops up again and keeps repeating itself.
I'm running Opensuse 11.4 with KDE, and my driver is ath9k. I don't know much about linux so please don't tell me to 'recompile this' or 'change this setting' without explaining how to do it. Please help, I've been unable to connect to wireless in OpenSUSE for 2 weeks now.
All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.
I am using OpenSuse 11.3 and Network Manager is giving me a headache by not connecting to WEP based wi-fi network.It works in a wi-fi at my office while at my home, it shows / detects the network but keeps asking me over and over.
I'm having some trouble connecting to the wireless network here at home. The PC has a Linksys WMP600N wireless network card, which works fine under several versions of Windows. In Opensuse however, I cannot get it to find the network. Even though my laptop is right next to it, which has perfect connection to the network. The router is a Linksys WRT610N.
I've tried running iwconfig and iwlist scan in the terminal, but the scan returns no results and iwconfig indicates it does not have a connection to a network. I've turned off IPv6 as I read this can sometimes cause issues. I've also tried issuing the computer a static IP address, figuring the DHCP might be causing problems, but all to no avail.
since a few weeks I have a problem connecting to other hosts when I'm using another wireless network, which has a different DNS IP than I have in my network. I have to change /etc/resolv.conf to change the nameserver. Can NetworkManager control the nameserver? If yes, how?
I can not get my network to work.Wireless shows no networks at all and wired the ethernet light does not even turn on. I have dpne heaps of searching but i can not seem to find a solution.
On the 32-bit Netbook with Intel Atom running opensuse-11.3 I have ethernet broadband connection with dynamic IP.I have now bought a D-Link Wireless 150 Router DIR-600 and have initialized it on my other laptop on Windows 7 Home Basic OS. I now want this opemsuse Netbook also to have the facility. Please advise me what packages I shall install and what modifications I have to do in /etc/sysconfig/network/ifcfg-wlan0 or whatever else is necessary.
I just installed opensuse 11.4 and i'm not being able to connect to my wireless lan. It recognizes my network, but when I click "ok" after typing the password it is like I had done nothing, no connection is set at all.I guess it is probably some configuration stuff since my notebook recognizes all available wireless networks. Sorry about the lack of details, but that is all I got.
i've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code: zypper in broadcom-wl broadcom-wl-kmp-desktop So now, the networkmanager detects all the networks around, but i cannot (or i don't know
I bought thinkpad t410 (2516cto) and just finished the installation of opensuse. I havn't noticed some incompatibilities yet, but there's no wireless. the wireless card is :Intel Centrino Advanced-N 6200. Anyone has any clue what's the reason? seems that the card was not recognized in opensuse yet.
I run Ubuntu, and it has a nice GUI widget thing that connects me to my home wireless network when I boot. I don't have a problem with that. But suppose I don't start X, and boot to a recovery console for some reason, like I did recently when my graphics were broken after installing Karmic. In that case, my computer won't be connected to the wireless network until I log into X normally. So I can't apt-get anything or anything. It's very annoying. And I don't know how to connect to my wireless network.
I know my wireless network SSID, and I know my WEP key or WPA passphrase. How can I log onto the network with commandline tools? Is there some basic program that I can just run "networkmanager <myssid> <mywepkey>"? I looked at the iwconfig man page and I honestly couldn't figure out how to simply connect to my network. Once I figure out how to connect to the network with command-line tools, where can I put an "autoconnect" script so that it will connect during startup, like it should anyway?
What I don't understand is, why the Ubuntu network manager nm-applet, doesn't just work as a front-end for more basic networking stuff. I don't see any reason why it should require you to start X before working; it could be a daemon that runs at startup, and there could be a config-file somewhere, but it doesn't even start running until I log onto gnome.
I am fairly familiar with Linux but had never ventured into Wlan settings / options / too much. I have compatible card (aetheros) and when running - iwlist wlan0 scanning - I get plenty networks showing up - meaning the card works. When I installed distro which is last night (before I ran update), I had that little bars menu at the top of the screen that showed available networks once clicked upon. Since I like to modify and make my settings better - I removed that little AT&T like bar, and now rebooted after update to find that I can not see available networks unless I use iwliset wlan0 scanning.... .#$*&)@&#(&%# - need I say more.
Two questions - how do you connect to the wireless network via command line? What is that vertical bars GUI tool called so I can find it and run it again? Is there (for the love of god) alternative to system-config-network GUI managment tool for wlan?
I'm tryn' to connect to my wireless network using command line:iwconfig wlan0 essid MY_NETWORK as root.
After this typingiwconfig wlan0 result is: wlan0 IEEE 802.11g ESSID:off/any Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:1 Mb/s
[Code]....
I installed ndiswrapper in order to use ipn2200 WinXp drivers.
I'm trying to connect to a wifi network where it hijacks all requests and redirects you to a page where you have to agree to a terms of use before it lets you connect to the actual outside world. This is a pretty common practice, and usually doesn't pose much of a problem. However, I've got a computer running Ubuntu 9.10 server with no windowing system. How can I use the command line to agree to the terms of use? I don't have internet access on the computer to download packages via apt-get or anything like that. Sure, I can think of any number of workarounds, but I suspect there's an easy way to use wget or curl or something.
Basically, I need a command line solution for sending an HTTP POST request essentially clicking on a button. For future reference, it'd be helpful to know how to send a POST request with, say, a username and password if I ever find myself in that situation in another hotel or airport.
I'm thrilled using wicd to connect to wireless networks. But when I suspend my laptop using the special keys, I just want to disconnect from wireless without having to use any kind of GUI or curses user interface. It says in the documentation that wicd works by sending DBUS messages, so presumably it's possible to write a command that talks to the daemon directly.But I can't figure out how.Does anybody know by means of what shell command I can tell the wicd daemon to disconnect me from my wireless network?
I am trying to do a command line installation.Finished the installation and my wireless card wasnt working.Did a "sudo ifconfig wlan0 up" and got it working.But for some reason wireless-tools is not installed thus I dont have iwconfig, iwlist, etc.The wireless works and connects fine off a liveUSB.So I am going to give info from this liveUSB run and maybe someone can suggest how I can set the right settings on the Command Line Installation I presume in the etc/network/interfaces.
The university I go to uses a WPA2 wireless network that requires a netID and password to connect too. I installed wicd but I can't seem to connect to this network, is there a way to add this functionality to wicd, and if so, how do I do that (links to a how-to or guide would be nice, I've yet to find one).
Also, I spend most of my time on campus in the command line, so I'd like to know if there is a way to use command line utilities to connect to this network (again, a guide or how-to would be nice)
I can get online through my fedora live USB just fine (w/ network manager) but I'd rather get on directly from slackware.
I have a CentOS 5.5 server running currently with a Netgear gigabit ethernet card and for wifi I have a wi-fi card with the chipset: RT2860.Now I have gotten the ethernet card and wi-fi card working but my main question is: How do you bridge the connection between the ethernet card and the wi-fi card to create a wireless network with a hidden ESSID if possible and WPA encryption? (So the server basically acts as a wireless router as well as doing all the other stuff I need to do on it).
On Linux Mint (Gnome) i used to go to Network drive. that is on the right hand side of Nautilus there is a short cut for Network. in there i could see my network hard drive and other laptops connected to the network, and i could access my files. but on OpenSuse, when i open the network folder, nothing comes up. may be it needs some sort of configuration.
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
abhishek:/ # sudo /usr/sbin/iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a Flags: bus master, fast devsel, latency 0, IRQ 23 Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
