I have a qzd netbook with opensuse 11.2 running but I cannot get the graphics working. I have tried "startx" and get the following:
xauth: creating new authority file /root/.serverauth.4650
X.Org X Server 1.6.5
Release Date: 2009-10-11
X Protocol Version 11, Revision 0
Build Operating System: openSUSE SUSE LINUX
[Code]...
I have unfortunately found myself unable to properly boot up openSUSE because I decided to buy the Acer Aspire with the i5 Processor.
I have the Intel Graphics Media Accelerator HD (GMA HD) graphics card, and unfortunately from all my searching online and on openSUSE, I have been unable to find a driver for this that works for linux, and in addition I don't know how to install a driver outside of a GUI.
My openSUSE boots up to the boot choosing screen (regular openSUSE or failsafe), and then that nice list of functions being done is displayed, but as soon as the daemon has started, suddenly my screen goes blank and I am unable to do anything about it. Beyond this point, my OS loses all functionability, and while I can hear it computing, I am unable to actually tell WHAT it is computing. get a driver for this and to install this driver and get this GUI running, that would be great.
I am running Opensuse 11.4 on a file server, based on an Intel Atom motherboard with 945G graphics chipset.I recently shut down and then rebooted the server (because I needed to switch off the power for a few minutes) after it had had been running quite happily for several weeks since the last boot. Now I cannot start X - it gives up after the line(EE) intel(0): failed to set mode: Invalid argumentI've tried googling but am none the wiser what could have caused this, or how to fix it. Excerpts from the X log file:
Code:
[ 229.187]
X.Org X Server 1.9.3
[code].....
I tried to install the ATI proprietary driver for an HD 5800 (Catalyst for Linux 64 bit, v. 10.8). The two main instruction sites are:
SDB:Configuring graphics cards - openSUSE
SDB:ATI drivers - openSUSE
I chose the hard way method. I downloaded the driver. Restarted SuSE 11.3 in mode 3. And as SU followed the method above, including adding the zypper programmes (which found some already installed and which installed a whole lot more). When I then attempted to run the install (sh ./atidriver-install-10.8-x86.x86_64.run) and selected automatic mode. It completed 82% and stalled attempting to install "Postprocessing Kernel Module".
I pressed control c to kill the process and attempted to re-install using the manual mode and then using the build mode. In both instances, same outcome. When I rebooted, and entered my password, the desktop did not load but sent me back to the username/password page. I can't get back in. Does not matter as I have backed up my docs.
I decided to install the proprietary driver because the colours on the desktop corrupt after the 2nd boot following a clean install. i.e. on the initial boot the colours are fine. Second, this is the 3rd effort I have made to install the driver after a clean install of SuSE 11.3 and there is no change in outcome. So, my question: anyone any suggestion what is going on and how I can install the driver successfully? Or, do I not understand the new regime in SuSE 11.3 and should I not attempt to install a new driver.
I recently installed SuSE 11.1 (64 bit) on my system
AMD Phenom II 940 3.0 Ghz;Biostar TA790GX 128M Motherboard with ATI Radeon HD 3300 Graphics card built in;
4 Gb (2*2 sticks) DDR2 800 MHz RAM
The installation went smoothly, But on first restart and login (and subsequent ones too!) I get a light purple screen with a skyblue box at top left corner, with xconsole written on it. when I Left click anywhere on the screen, I get a popdown with a number of options, of which only XTerm (bash shell) and exit (logout) options work. Now I know the HD 3300 graphics card drivers are not built into the SuSE 11.1 distribution, and I have already downloaded them (Linux ones)from ATI website. I login as Superuser, and type init 3 to go to a very basic screen,login as user, change to superuser again and then run the following file i downloaded from ATI:
sh ati-driver-installer-9-4-x86.x86_64.run
The result/output at the command prompt:
Created directory fglrx-install.ubanI5
Verifying archive Integrity... All good.
Uncompressing ATI proprietary linux driver-8.602...
.....(lot of dots)...
ati-driver-installer-9-4-x86.x86_64.run: line 295: ./ati-installer.sh: Permission denied Removing temporary directory: fglrx_install.ubanI5
Once again, i tried everything in superuser login.
Also I tried making changes via sax2 command, it doesnt seem to work. A window opens where I see that my graphics card has been detected but thats about it. nothing else in that option, everything is greyed out (nothing to be selected)
I have an HP Pavilion dv6-2120ca and I'd like to find out where to find the graphics driver. This is the card: TI Mobility Radeon HD 4200 Graphics I plugged in my MP3 player in and it worked with Opensuse.
View 2 Replies View RelatedCaution to all using ati graphics download repository. I have been using SUSE 11.4 after an upgrade from 11.3 through zypper for months. I added ati graphics as a update repository. Software update installed two ati files. I did not notice their names.
Upon installation my graphics was acting funny so I uninstalled the two ati-files figuring I'd be back to where I was. Now I can only get into terminal window after reboot at both runlevel 3 and 5; no graphics at all. I keep getting message re: display 'null' I wish to return to original graphics configuration prior to ati downloads which, I believed used xorg drivers.
I believe I either need to revise xorg.conf file back to original which was overwritten by ati process or reinstall xorg/X11 related files. I have an ati radeon HD 3450 agp card. 32 bit SUSE w/11.4 installed and running. Anyone have a sample xorg.conf that might work or some other ideas of how to get back to where I was.
As a related question, if I do a fresh reinstall of SUSE 11.4 using dvd can I save my /home files and any /filesystem files that my special software created in root directories.
I have a dell studio 15 laptop which has a ati radeon 4570 512 graphics card and i m using fedora 12 my problem is that, on the ati site there is not any dedicated graphics driver for my 4570 on ati site, i just want to know how can i install grahics driver for my f12 OS. is there is any one in the community who is using a similar ati card
View 1 Replies View Relatedi m using acer aspire,and it is intel 945gm. i click on extra in preferences but nth happen
View 9 Replies View RelatedI am thinking of buying a new computer. It has ATI Radeon HD 3000 Graphics. Will that work with Fedora 14? Will I need to install a driver to get it to work? If so, where would I download that driver?
View 3 Replies View RelatedI have already installed Debian testing and now looking to install Nvidia drivers version 190.
I had downloaded the Nvidia driver from their site but the way it installed on Ubuntu is not the same here in Debian. Obviously, I failed.
I downloaded my Proprietary ATI Linux Driver (for my Radeon Xpress 200) from [URL]... But I cannot figure out how to install it!I followed the instructions here but Terminal told me "command not found". I also tried double-clicking the file but it opened with gedit and gave me an error.
View 9 Replies View RelatedI just installed virtual box on my winXP, and also installed ubuntu on virtualbox but it is extremely hard to install virtualbox graphics driver on ubuntu
View 2 Replies View RelatedI have just had to install CentOS 5.6 on a family members computer, as they lost there Windows XP key. Anyway, I am needing to install a new nvidia graphics driver. I found a howto on this forum for 5.2 [URL]
View 5 Replies View RelatedI installed FC14 on my Lenovo Thinkpad T410.
I want know if is possible to install additional graphics driver and how to.
I installed Ubuntu 10.04 on my PC last weekend. Other than the fact I had no sound (that's another story...), everything went fine. I then got prompted to install nvidia graphic drivers. Since I installed them and rebooted, i cannot get acces to my ethernet connection. I tried the solutions listed here, but none worked. Also, when i boot on my windows OS, the Internet is working properly. I tried tonight re-installing Ubuntu 10.04. I thought if the graphic caused problem, maybe a new blank installation would just do it.
View 2 Replies View RelatedI'm trying to install a driver for a Radeon x700. I downloaded the driver from the site and the sh command to install it but this is what I got.
View 2 Replies View RelatedOur BIOS use AMI,Memory:1GB,CPU:Z510,
then install ubuntu 9.04,GMA500 Driver,but refer Inf is:
The following error was encountered. You may need to update your configuration to solve this;
(EE) psb(0):THE STOLENbASE IS :OX1FC00000
(EE) psb(0):Screenindex is:0;
fbphys is :0x1fc00000;fbsize is:0x003bf000
(EE) Psb(0):Could not find a valid initial configuration for this screen;
(EE) screen(s) found, but none have a usable configuration;
, then I try to modify the Stolen Memory to 8MB,but result no change; I doubt BIOS need do some change ,but don't know how to do,
Cutting a long story short (my machine won't allow me to login without the proprietary fglrx driver installed), how do you install the fglrx driver in Natty, from the console? he following commands have been suggestedbut haven't worked:
Code:
apt-get update
apt-get install fglrx fglrx-amdcccle fglrx-dev
[code]....
After installing the ATI graphics driver that was suggested under System > Devices, ubuntu required a reboot. now it either hangs on boot, or boots into the Bash shell. I tried the option in the Grub boot llist to boot into recovery mode, and then teh option to fix recent update (or something like that), but it did not help.
Assuming the ATI driver is the problem, how can I back it out?
Infact I've seen the linux(ubuntu 11.04) for the first time today. I don't know anything about linux & i'm not able to install my nVidia 8600gt graphics driver. I've downloaded the .run file from here
[URL]
when I'm opening the .run file it's showing an error
"Could not open the file /home/f1/Downloads/NVIDIA-Linux-x86-275.09.07.run.
gedit has not been able to detect the character encoding. Please check that you are not trying to open a binary file. Select a character encoding from the menu and try again."
After trying for all day long I found this HOWTO
[URL]
Using Ubuntu 9.10 I installed Ubuntu onto a second hard drive and everything seems to work fine except for the fact that I cannot install the driver (it says not supported or something) when I downloaded it from the website. I downloaded the driver made for Linux. The driver manager claims "no proprietary drivers." At the moment it shows to be using integrated graphics, but I need the full hardware graphics to play games. The open source alternate driver didn't work either.
View 2 Replies View RelatedAfter a disk crash I reinstalled openSuSE 11.2 and as always downloaded the latest Nvidia driver for my geforce 8200 graphics.
Unlike all previous cases, this time the driver does not install. The contents of /var/log/nvidia-installer.log are below. The error refers to being unable to to locate version.h
PATH:
Using: nvidia-installer ncurses user interface
ERROR:
For those who need or want to install the latest ATI proprietary driver (Catalyst 11.2) right after a fresh 11.4 install - and might not look for solutions in the development subforum.In order to compile the module, I installed the kernel sources and the pattern devel_basis. I normally use most packages in this pattern, so I install it by default from other scripts. While running atiupgrade on a fresh install, I was surprised by the number of packages getting installed with that pattern.Please report if it doesn't work. (like aticonfig initial failed to add a fglrx section for some reason).Take a look at the atiupgrade thread in the development forum: Upgrading ATI driver with atiupgrade.
View 9 Replies View RelatedSo ... right now I'm having an issue after I installed ATI Catalyst 10.8 for my GPU HD 5770.Every time I try to boot, it sends me to init3 (I mean text screen). But when I check and try to switch to init5, it tells me that I'm on init5 already.And I'm still stuck on the text screen. However, safemode is still working (yeah I'm on it right now - -").
I installed ATI driver by using this instuction --- openSUSE Lizards � ATI HD57xxx fglrx drivers under 11.3
i know if u search a solution in forums u get so much confused information. i hope this little manual will help all with the nvidia driver problem! u dont need to edit or create a xorg.conf or something to run the driver correct and u need no blacklistedit too! if u did the standard opensuse 11.3 install its only about 2 kernel packages and the disabling of the x11noveau driver.
1. after standard installing opensuse 11.3 update and install the opensuse softwareupdates
2. install with the yast software re/installer:
(from Desktop or from the terminal. the terminal text command is: yast2)
[Code]...
u dont need to change the menu.lst after all, only u get many problems. run the midnight commander and delete the nomodeset word and the noveau driver would be normally still active after reboot.
I've had a graphical card and I've downloaded the driver (from the official website of NVIDIA) with extension .run. As I forget the command line to install it, I would like to ask about it.
View 3 Replies View RelatedNvidia h/w:Quadro FX 570
Installed 11.4 yesterday. No problems. Installed Gnome 3 today and it goes into fallback mode. Assuming that the graphics driver might be the culprit, I attempted to install the latest nvidia driver.
Added repo ftp://download.nvidia.com/opensuse/11.4/ in Yast2.
Did a refresh and it complains that it cannot access installation media at the above. Paste the above in Firefox and it gets there OK.
One-click method also fails.
Never had a problem with updating nvidia driver before. Not sure what to check. I did delete and add with no success.
BTW, the other defined repos in Yast2 work fine.
I have installed openSUSE 11.4, and I really like it compared to other linux versions I've tried, but I find it requires a bit more linux know-how.
Being fairly new to linux, it has been quite the effort to learn but I started getting the hang of things via online support and such. Lately I've been having some problems.
I need linux to run a TCAD program, and it requires some openGL functionality and was giving me errors when I tried entering the software related modeling GUI.
Anyhow, I thought it had to do with my graphics drivers, so I decided to update them via ATI proprietary driver. After doing this, the system booted me into the console rather than X.
I tried numerous online guides on how to fix the issues, by running all sorts of boot commands (nomodset), and I read the graphics driver theory, as well as trouble shooting ATI graphics.
In the process, I also installed a radeonhd-xorg11-something through YAST, and that caused a black screen altogether upon boot. I managed to boot into failsafe with x, and from there I removed it via YAST, however this did not resolve issues. I also deleted any xorg.cionf files in hopes that the system will default back to the radeon driver.
As it stands right now, I can only boot into my system via failsafe mode. I'm keeping the unit off for now as it's probably tired from all the hard reboots I had to do . If someone can help me resolve this issue, I can turn it on and enter any commands required, such as finding out the graphics card, the kernel, the driver currently running, etc and I can post it here.
I was looking to get glx to work with direct rendering. So i installed the nvidia drivers from the openSuSe Sight. I installed because /var/log/Xorg.O.log Said that the Nvidia card was not loaded. Long story short looks like the card is loaded but X windows... I guess GLX is not running and neither is Opengl. I still have output to the monitor. here is
[Code].....
