When doing the install, all appears to go well. I added the "nomodeset" option after the first boot to avoid the graphics issues. KDE comes up and is in 800x600 mode at 50hz. That is the best resolution it will show. All other options in the configure desktop applet are lower. This monitor was driven at 1900x1200 on the same config with 11.2.
[Code]...
In the nVidia-Settings applet (run as root), it shows the display as "CRT-0". 11.2 showed it as a Dell.
I've just upgraded to 11.4 and found myself with the same problem that I posted in Available resolutions vary depending if monitor is on or off when starting the system I'm using this pc as a server, and I acces to it most of the time via VNC, so the monitor is turned off almost all the time. If the pc boots while monitor is on, i have a resolution of 1280, if it's off I get 1024.
In the previous post I fixed this using the option "CustomEDID" in my xorg.conf, but this time I have no xorg.conf file to put this option in, and even if I did, since I'm using the default drivers (Nouveau, i think) instead of Nvidia oficial ones, i have no clue about how to obtain edid.bin. how to fix this without installing the propietary drivers? (since i don't need ant fancy 3d effects, kde seems to work fine and performance is ok)
I am using 11.4 32 bit Gnome. It is working fine expect high CPU usage. Specially by X-ORG. I am running this on my old PC with core2duo, Intel motherboard DG31PR, Integrated Intel GMA 3100 Graphics(intel G31 Exprss chipset) , 3 GB RAM I went to Hardware information in YAST and found some discrepancies.
1. desktop board is listed as D945GTP instead of DG31PR 2. in framebuffer 1440 X 900 is not listed which is my monitor resolution 3. BIOS info has no vendor name
I downloaded x86-64 hybrid DVD and done everything according to instructions from Installation without CD - openSUSE.After booting from USB HDD, the first page took about 3 minutes to switch menu to the installation media option then afterwards the installation got stuck on Hard drive detection (probably 2 hours before i rebooted into windows 7). Installation scenario is:
Machine: Compaq presario C767TU HDD: 320 GB with Windows 7 Ultimate on root partition, all other partitions NTFS Free Space for Linux: 30 GB (Extended partition) currently having Mandriva 2010 with /swap 2GB, / 10GB,
I've just installed Ubuntu on my laptop. My laptop has an nVidia card so I'm forced to use the nVidia configuration tools. What I'd like to happen is for it to automatically start using my monitors if they're detected. OR, make a simple script that will enable the monitors without needing to restart X.
I have two pc`s . one i have installed it with openSUSE 11.1 and another with openSUSE 11.2. When i connect my printer HP Laserjet to 11.2 it get automatically configured, while when i connect the same printer to 11.1 it will not get automatically configured. I will have to use hp-setup tool to setup my printer. When i googled i collected some information that 11.2 version uses udev-configure-printer to automatically setup the printer whereas in 11.1 i did not find it. What changes that i will have to make in 11.1 to setup my printer automatically..?
I move from Win to SUSE. I install Suse 11 on notebook with pluged extern monitor, but when i un-plug this monitor then no screen is visible - only black screen. In "failsave" it works but in normal ee :-(and I tryed clone screen- nothing) SUSE detect only ext monitor. Manual settings of resolution is not working.
I put "%" before and after my username and name which gave the install an error. So I changed the username to one without the special character '%' but left the name with and the setup proceeded with an error and skipped the other three stages (sound testing, time, hardware setup). But everything seems fine with the install except I have not configured the sound card.
From what I have seen the install is pretty much fine other than the lack of functions which I obviously missed during the preference end section of the install. And so I was wondering is there a way to manually detect and use a easily configure a sound card or any way for that matter? The installation guide of Fedora 11 gives advice that was outdated 'system-configure-soundcard"(or something similar) has been removed since F9.
[Code]...
Currently have a few mixers installed which may be conflicting but the extra mixers were a symptom I created due to the no sound problem. The mixers are definitely not the major cause though. My onboard motherboard sound has not been set up as a module to be run is what I assume but any help would be great.
I have a dual-monitor display with a Nvidia GEforce 9400 video card. The login screen has a normal login on the primary display but the second display contains fragments from the previous session. I would like to clear the secondary display so that it does not display information from the previous session.
The default Gnome desktop now has a 1600x1200 @ 75 Hz which fit my monitor but is a little too big (or at least the font sizes are too small). I would like to switch to a lower resolution. I don't find anywhere in Yast how to configure the monitor settings. No more sax2, no more /etc/X11/xorg.conf? What does replace them?
I mean, where can I set which monitor I"m using (Targa TM4896-1), what are the screen resolutions supported, if I want hardware 3D acceleration (or not), if I want to use dualhead (Matrox G400 DH)?
I have a few machines set up to run off in the corner without monitors attached. I installed 11.3 (32-bit) on a couple of them and they run fine during setup but then I move them to the corner with no monitor attached and they won't boot correctly.
By this I mean they still run some apps I setup to run automatically from daemon scripts, but I can't ping or access the machines at all. It's almost like they aren't booting all the way up. Hooking a monitor up fixes this but I don't have enough monitors to keep these hooked up like this.
I have a couple of other 11.3 systems that are setup almost the same way but I put graphics drivers on those and they work with or without monitors attached. I don't want to have to put graphics drivers on those systems.
I can''t make the machine booth when a monitor is NOT attached to the machine. The PC seems to get past the P.O.S.T with minimal HDD activity, and then it simply hangs there, doing nothing. I know Linux is not booted because the HDD flashes briefly only 3-4 times and then absolutely nothing. When a monitor is attached, everything works perfectly.
I read somewhere that this happend when GRUB tries to display graphics, so I edited the menu.lst and removed the graphics line within it, which causes GRUB to display a B/W clear-text boot-menu (when a monitor is attached), but the machine still won't boot with no monitor. I also edited inittab to boot to level 3, same outcome.
More Info: HW. FIC ION A603 ~Welcome to First International Computer, Inc.~ OpenSuse 11.2 - Almost default install Added SW: VNC and Squid (both active on Init 3 and 5 Boot Loader: GRUB
I have a problem with my screen resolution in Linux. This happens with both openSUSE 11.4 and Fedora 15. The moment my PC restarts after I have installed the operating system it will boot up with a screen resolution higher than my monitor supports. My screen supports a maximum resolution of 1600 x 1200 @ 75Hz and Linux sets the default resolution way too high at boot, now all I get is a message from my screen asking me very nicely to change the signal timings, but I can't because I can't see anything to change it to a lower value (I don't want it so high anyways because then everything is too **** small). My monitor is a SONY GDM-5410 and the Graphics card is an AMD Radeon HD 4870 1GB. It nly works when I boot the system to FailSafe mode, but then I can't cahnge it permanently.
openSUSE 11.2 (i586) VERSION = 11.2 on an IBM x3250
Problem is that after the screen comes up to chose the default version or failsafe, my monitor shows no input. If I delete the VGA 0x031 (i think that's the number) on the Options line in the screen where you chose the version, I get my command line interface.
I am booting XP and Opensuse 11.4 all was ok until I changed my old monitor for a widescreen monitor, Xp works ok but when I select Opensuse from the menu it just boots to a black screen.
This is a triple-monitor setup with two video cards, where the mouse pointer gets "stuck" if it tries to cross from one video card to the next one. It worked correctly in openSUSE 11.2 and doesn't work in openSUSE 11.3 with the same xorg.conf. This is a 64-bit openSUSE 11.3 with xorg 7.5-11.3 (the openSUSE prepackaged version). I've already tried NVidia drivers 256.53-16.1 (the openSUSE NVidia repository version) and 260.19.12 (the latest off of the NVidia website).
This is the same xorg.conf that I used successfully in openSUSE 11.2. I tried a new automatically generated xorg.conf using nvidia-settings and it had the same problem. This forum won't let me upload the relevant files, but here: [URL] is a tar-ball with my xorg.conf, Xorg.*.log, /var/log/messages, and the NVidia debugging output.
just setup suse 11.3 , put on the Nvidia 19.29-22.1 drivers via yast , no kms is set in inetd , nomodeset on grub boot line etc... Even tried installing the driver " the hard way " dual monitors come up, setup xinerama to "Extend" my desktop , and the main monitor ( right side ) is good, visually the left monitor (2ndary) is good.. but whenever I move my mouse over to the left screen the mouse pointer dissapears, flickers along the right hand border of that screen... and if i move the cursor back to the original screen i have to really fight to get it back to the main screen....Copy of my xorg.conf , still very basic...
# nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04. nvidia.com) Wed Dec 8 12:27:27 PST 2010
the solution of my monitor is much to small. So I tried to find out, where I can change the settings of my graphic card and monitor. Unfortunately opensuse only gives me the possibility to change it up to 600x800, which is by far too small. So I thought maybe I need to install a driver... so... there I am ... having question marks around my head and wondering how to install a graphics card driver on my opensuse 11.3.??? And where to find the right ones?
My graphic card is a Matrox Mystique (no 220 or anything else!!). I checked the website of Matrix to find my drivers, but it tells me that there is no driver planned for linux. Matrox Graphics - Support - Latest Matrox drivers for legacy products But I guess I am not the only person in the world who uses this graphic card on linux, so there must be a way to make it work!!
I had to install the nVidia proprietary drives so the OS would boot into Gnome3 and not fail safe mode. Without the proprietary drivers installed the display settings said:
Driver: software rasterizer in use
After installing the nVidia drivers Gnome3 works in one monitor, but I would like to be able to use my other two monitors (totaling three with two video cards.)
When I run nvidia-settings to generate an xorg.conf file it hangs, so I used nvidia-xorgconf to generate the xorg file and then used nvidia-settings to configure my extra screens.
This fails with a permissions error, running sudo nvidia-settings fails with the following error:
ERROR:
So, I ran nvidia-settings, saved the settings file to my /home/$USER dir, then copied xorg.conf to /etc/X11/
Logging out and logging back into Gnome fails with the error:
This problem extends to Ubuntu running Gnome3, so my thinking is: a) Imma id10t and something in my xorg.conf file is wrong, b) there is an issue with Gnome3/nVidia/Multiple displays.
I would really like to use Gnome3, it works on multiple other machines (ironically all ATI devices) just not the machine I use all day long...
Here is my xorg.conf file as generated by nvidia-settings.
I have just installed Os 11.3, it is my first time to try Linux. Install went fine have Dual Boot Win7 and openSuse 11.3 KDE I have a 26" TFT TV as Monitor 1 DVI and Dell 16" as Monitor 2 VGA all working fine . Autoconfig started and TV display vanished, install finished and went into display settings to check problem and for some reason it is saying both displays are on my 16" Dell. I will Add Screen Shot to show problem. wanted to switch to Linux for years but never had the guts, i was hoping to learn Linux with this distro and when have a grip on it drop windows and use Linux as Primary.
Like subject says, everytime my computer put the monitor on standby when I wake up the monitor the computer keeps loggin me out of my account, have to log in everytime i wake up the **** monitor, anyone knows a way to fix this behavior?
I found this thread by looking up ultramon replacement: [URL] I would like to use "swapmonitor", to make it easy to move windows from monitor to monitor in a dual desktop environment. I have no idea how to install it.
My OpenSUSE 11.2 is working fine as samba server, no problems, but I have a problem with KDM.My default init runlevel is set to 5 and every time I try to login at KDM (KDE4), the monitor goes black and returns to the login screen.If I hit Ctrl+Alt+F1 to go to console and start /usr/sbin/console-kit-daemon manually, press Ctrl+Alt+F7 to return to KDM login, everything is fine.What do I have to do to fix this issue?
I want to write a piece of C/C++ Code which will tell me whenever the USB is plugged in to the system or when ever any USB Device is unplugged from the System.
It should give me daily internet usage stats something/vaguely like this:-I have tried ntop and darkstat ,but they were too complicated and cannot be launched from notification area like this..Also tried using KtrafficAnlyzer by installing KDE core, i am not very amused by the idea of having to install a massive run time file package for a simple tool.
