OpenSUSE Hardware :: Kde / Nvidia Slow Down With Dual Monitor Configuration - Resolve It?
Mar 4, 2011
I run opensuse 11.3/kde desktop.
- updated to KDE:Factory
- X11 repository (V1.9.3)
- proprietary nvidia drivers (260.19.36)
Video card is a Quadro NVS 290. A dual head configuration using twinview is run.
The desktop becomes slow almost immediately (couple of seconds) after logging in (all applications). Turning off desktop effects does not make a difference as well as trying the various recipes on the internet regarding x.org conf-files.
The only action restoring responsiveness is to simply start nvidia-settings. Putting the following pseudo-action into a script-file and mapping it to a key allows to have a workable environment:
nvidia-settings -a PixmapCache=0 && nvidia-settings -a PixmapCache=1
It is very annoying having to press a key every minute or so. Instead of creating a cronjob I would like to solve this issue. This behavior has been consistent across kde/x-org/nvidia/kernel updates for many month now.
View 6 Replies
ADVERTISEMENT
Jan 15, 2011
just setup suse 11.3 , put on the Nvidia 19.29-22.1 drivers via yast , no kms is set in inetd , nomodeset on grub boot line etc... Even tried installing the driver " the hard way " dual monitors come up, setup xinerama to "Extend" my desktop , and the main monitor ( right side ) is good, visually the left monitor (2ndary) is good.. but whenever I move my mouse over to the left screen the mouse pointer dissapears, flickers along the right hand border of that screen... and if i move the cursor back to the original screen i have to really fight to get it back to the main screen....Copy of my xorg.conf , still very basic...
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04.
nvidia.com) Wed Dec 8 12:27:27 PST 2010
[code].....
View 9 Replies
View Related
Jul 22, 2010
I have opensuse 11.3 (64 bit) with nvidia 8400GS (256 MB ram). The system is a core 2 T7500 with 4GB Ram. I have installed nvidia drives (through nvidia's .run file, versison 256.35)
1) When i connect an external monitor (1440x900) and use separate x-screen+ xinerama (laptop has 1280x800), desktop response is really slow. Moving windows,switch tabs etc make desktop (kde) barely useful. Especially if i open a large txt file it is almost impossible to scroll through this file.
xorg file (see attached file) is been created by nvidia-settings.
One minor solution I found is to use 16 bit (instead of 24bit) color. This makes everything better, but still not fast enough. I do not use desktop effects.
An important note: This happens only after some period of time. After reboot everything seems to be ok for some time, but suddenly something changes and I have slow response.
I do not have the same problem under windows.
2) How can i specify that laptop's screen be the default, so it can have the taskbar?
3) When i disconnect the external monitor and restart x, then the laptop screen goes to 1024x768 and not to 1280x800. I have to create another xorg.conf and restart x. How can I make just one xorg file, and the system automatically adjust resolutions regarding if i have one or dual monitors?
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 256.35 (buildmeister@builder97.nvidia.com) Wed Jun 16 19:14:45 PDT 2010
Section "ServerLayout"
[Code]....
View 5 Replies
View Related
Feb 5, 2011
I have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
View 1 Replies
View Related
May 8, 2010
I've managed to get dual monitor support working, but it seems a little sub-standard.
- I can't find how to alter the relative y offsets of each screen
- I can't drag windows from one side to the other
View 3 Replies
View Related
May 25, 2011
I have recently installed FC15 on my system. Dual monitor support seems to be broken with my setup. I am using the latest NVIDIA binary blob driver (270.41.19). I compiled my own kernel for it, version 2.6.39.
When gnome3 starts it almost manages to boot up, but then it crashes and gives me the option of logging out. I have my system booting into target 'multi-user.target' since I was doing some other stuff and I use `startx' to start gnome3. I tried running having X use xinerama and not use xinerama, both cause gnome3 to crash, albeit in different ways. Other than that I am running a stock install as far as I know.
If there are some logs I should be looking at for gnome3.
View 4 Replies
View Related
Jan 26, 2010
I have a dual head setup with NVidia drivers. Is it possible to run gnome - screensaver (or xscreensaver) only in one head / monitor?
View 1 Replies
View Related
May 5, 2011
How can i be able to enable dynamically my second monitor and use Unity at the same time?Summary system:HP Compaq 8710p laptop, Nvidia Quadra 320M, Natty 64bit, with attached 2nd 19" monitorDescription steps taken this far:By default ubuntu ships with the following xorg.conf conform the new minimalist trend:
Code:
Section "Device"
Identifier "Default Device"
Option "NoLogo" "True"
EndSection
I use the nvidia-current binary drivers. In this configuration:Unity works Xrandr sees 1 screen (so no configuration of second screen possible)Standard monitor configuration tool in Ubuntu shows 1 screen With [URL]
Code:
disper -d auto -e
my second monitor comes alive. My laptopscreen becomes dark (with moving mouse cursor). Unity / Ubuntu classic (no effects) go into scrambled mode. Mouse is moving, objects are
[code]...
View 9 Replies
View Related
Feb 18, 2010
I wanted to know how to save the dual monitor using Nvidia X server Manager. I googled how to and it said to delete the "xorg.conf" However I dont have the Permission to delete this file so I would also need to know how to gain full admin access to my Ubuntu Account.
View 4 Replies
View Related
Jun 22, 2010
I've just installed Ubuntu on my laptop. My laptop has an nVidia card so I'm forced to use the nVidia configuration tools. What I'd like to happen is for it to automatically start using my monitors if they're detected. OR, make a simple script that will enable the monitors without needing to restart X.
View 1 Replies
View Related
Jun 7, 2010
I am trying to install nVidia drivers on CentOS 5.4 and it is requiring kernel-source
# lspci | grep VGA
01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 8400 GS] (rev a1)
For the installation of kernel source, I have followed the steps on [URL]. I followed the steps under 2.1 and they worked for me. Now what can be done for the installation of the kernel-source package. When I am trying to install nVidia drivers, I am getting error, following are lines from installation log of Driver.
-> Tagging shared libraries with chcon -t textrel_shlib_t.
-> License accepted.
-> Installing NVIDIA driver version 185.18.31.
-> No precompiled kernel interface was found to match your kernel; would you like the installer to attempt to download a kernel interface for your kernel from the NVIDIA ftp site [URL]? (Answer: Yes)
-> No matching precompiled kernel interface was found on the NVIDIA ftp site; this means that the installer will need to compile a kernel interface for your kernel.
-> Performing CC sanity check with CC="cc".
-> Performing CC version check with CC="cc".
ERROR: Unable to find the kernel source tree for the currently running kernel. Please make sure you have installed the kernel source files for your kernel and that they are properly configured; on Red Hat Linux systems, for example, be sure you have the 'kernel-source' or 'kernel-devel' RPM installed. If you know the correct kernel source files are installed, you may specify the kernel source path with the '--kernel-source-path' command line option.
ERROR: Installation has failed. Please see the file '/var/log/nvidia-installer.log' for details. You may find suggestions on fixing installation problems in the README available on the Linux driver download page at [URL]. I want to install driver.
# rpm -q kernel-
kernel-2.6.18-194.3.1.el5.centos.plus
# rpm -q kernel-devel
kernel-devel-2.6.18-92.el5
kernel-devel-2.6.18-164.15.1.el5.centos.plus
kernel-devel-2.6.18-194.3.1.el5
kernel-devel-2.6.18-194.3.1.el5.centos.plus
# rpm -q kernel-source
package kernel-source is not installed
The nVidia Driver I am installing is:
NVIDIA-Linux-x86-185.18.31-pkg1.run
# uname -a
Linux harvey 2.6.18-194.3.1.el5PAE #1 SMP Thu May 13 13:48:44 EDT 2010 i686 i686 i386 GNU/Linux
Only reason to install the proper driver is to use dual monitor.
View 6 Replies
View Related
Nov 26, 2009
I used preupgrade to upgrade from F11 to F12. In F11, I used the proprietary nVidia drivers from rpmfusion, and they worked well. I have refrained from installing the nVidia drivers in F12, because of the problems reported for users of KDE. I removed my old xorg.conf, which has references to the nVidia driver and to "TwinView," the proprietary method of managing two screens, so as to let X discover both monitors.
Now, however, my second monitor stays black, even though xrandr and KDE RandR show both monitors correctly. Xorg.0.log shows the nouveau driver is loaded. (I also tried to create a new xorg.conf following guidelines from the web, but many of the guidelines are from before xrandr, and I'm not confident I have it right yet.) It seems that X believes I have two monitors, because I can drag a window off into the blackness (and it's never heard from again!) I know that the hardware is working, because I just booted into Windows 7, and I could see the desktop on both windows.
How do I convince X and KDE to display on both monitors?
View 2 Replies
View Related
Jun 21, 2011
I have an NVIDIA 9800 GTX. I have 2 DELL monitors connect to this card, one is a 24" and the other is 21".
I am unable to use Xinerama mode with Unity, because for some reason after logging in, I get no desktop interface, only background wallpaper, and I have to force reboot.
How can I setup dual monitors in Ubuntu using Unity properly? Note that I do NOT want to use TwinView, since this results in dead space around the smaller monitor.
View 7 Replies
View Related
Feb 25, 2010
I have Ubuntu 9.10 installed on my computer. I also have Galaxy (Nvidia) 9500 GT PCI-E card installed on it. I can get both monitors (Acer X223w) to work but every time I shut off the computer and turn it back on the second monitor is shut off. I just need to turn it back on using Nvidia X Server Settings. I have tried to save my X configuratin file but I keep getting an error of:" Unable to remove old X config backup file '/etc/X11/xorg.conf.backup'. I have a feeling this is because I am not signed in as root. Is this correct? If this is the case is there a way to get to sign in as root not using the command lines? Otherwise they need to remove this button. I can manually create a backup (copy paste into a text file). I think. Getting back to my Xorg.conf file, I think I need to modify it to have two screens. I have also got some information on my video card using the lspci command. I think I need some information from this. I have written below (towards the bottom) what I think the file should be. Now before I do this, does anybody know of an easy way to back up my whole computer? With my luck I am about to screw something up big time. I think I can just get away with the text file that I copied from the Xorg. Worst case scenario I will just manually replace the file.
Information on my computer:
OS: Ubuntu 9.10 32bit
Motherboard: ASUS M3A78
CPU: AMD Phenom 9500 Quad Core
Video Card: Galaxy Geforce 9500 GT 1GB 128 bit DDR2 (Nvidia)
Hard Drive: Hitachi 1 TB Sata Drive 3 Gb/sec 7200 RPM
Ram: 4 GB (I think, its been awhile since I built this thing)
DVD Burner: LG
Here is a copy of my xorg.conf file: (I don't think it matters but I have both monitors turned on right now).
from the lspci | grep VGA:
I think I need the 01:00 information for my Bus ID. The only thing that I am confuse on is that I was expecting to see two of them.
Okay, this is what I think I need to do: I tried to add color to make it easier to find the changes I made but for some reason I cannot. I will add **** on the end (right side) so my additions and questions will be easier to find.
Do I need to add another Device for the video? Doesn't make sense to me since I only have one video card. I was told it should be based on the # of chips on the card. So I guess I should have two of them since I have two outputs.
View 2 Replies
View Related
Nov 24, 2010
I have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
View 3 Replies
View Related
Feb 7, 2010
I have an Acer 1200X with an Nvidia 8200 graphics GPU integrated on the motherboard. I have an HDMI and VGA output. I have downloaded the Nvidia graphics driver using envyNG and the old fashioned way. I have tried configuring the monitors 15 ways from Sunday in the configuration and I cannot for the life of me get dual monitors to work.
When I go into configuration with the Nvidia wizzard it blanks like its going to work then just stays black with the mouse cursor. I also cannot save as I get a "parsing" error. I am using Ubuntu 9.10 and have even tried using envyNG to get the monitors to work on twinview... NOTHING Hope someone can help!
My dad who is a Linux nut came over to help and he left 3 hours later because were tempted to chuck the computer out the window...I need to figure this out as this is going to be my work computer and I need dual screens.
View 1 Replies
View Related
Jan 12, 2011
I have the nVidia GeForce 8500 GT 512MB graphics card, I put it in my system to get a speed boost and for a dual monitor setup, I don't have the proprietary drivers installed I tried installing them, and when I did it asked for reboot, so I did, and when it came back up only one monitor was in use, and it was running very very sluggish, so I opened up the Monitors from the settings and it said to use nVidia's thing, so when I did, I enabled the second monitor, and hit apply, and it asked for a restart of Xorg, doing that came back telling me that no monitors were find, and a reboot brings me straight to tty1... I tried both the recent version and the older one, both did the same thing, I really wanna get my Compiz effects back. is there a way to get this working? I will do anything you ask if it solves the problem...
View 2 Replies
View Related
Aug 10, 2011
One monitor is working fine but the display is not coming on other monitor. I guess no problem in monitor because I swapped the cable to check the individual monitor. When I try to install the new driver its giving GCC-VERSION-CHECK while installing. And I do not think I have to install the new driver because it has already one. What should I do to configure the dual monitor. Do I have to edit any configuration file.
My system configuration details are below.
Redhat version : Redhat Enterprise Linux WS release 3 (Taroon update 4)
Driver in SRBC 26: NVIDIA-LINUX-x86_64-1.0-7664-pkg2.run
Nvidia card model : Quadro fx p171
Bios version of Nvidia : 4.35.20.23.07
p/n : 900-50171-0400-0000K
600-50171-0002-201J
View 3 Replies
View Related
Jan 1, 2010
I have activated dual screen monitors using the Nvidia driver GUI as Sax2 would not correctly configure it. Now at every boot I get the message "undefined video mode 31a, press [enter] for a list of video modes or [space] to continue. After pressing space the system boots to my liking, how can I get rid of the message at every boot up?
I am using Suse 11.2 and KDE4.3.1 My video card is an Nvidia Geforce 7100 GS I thought I was using the Nvidia drivers as I have a GUI from Nvidia in my launch menu if I search "Nvidia" and I have completed the one-click installation. Although when I go into "My Computer" it says driver unknown.
View 8 Replies
View Related
Feb 11, 2010
I'm having a rather hard time getting my 3 monitors setup as one display. I can get all three to work without too much heartburn using 3 separate X instances. The monitors are on 2 different video cards, one dual heads. The other on it's own card.
I've tried countless ways to get this to work, and I'm just not feeling the love. There are 2 17 inch monitors on the 1 video card and then the second video card has a 24 inch monitor on it. I can get the two monitors on one head to work with twinview, but the third one is left out.
The physical configuration looks like this..
17inch on the left of the 24 inch monitor, and another 17 inch monitor on the right, with the 24 inch monitor being in the center.
I'm going to include my current xorg.conf and lspci.
xorg.conf
Code:
harry@ubuntu:~$ cat /etc/X11/x
xinit/ xkb/ xorg.conf xorg.conf.backup
harry@ubuntu:~$ cat /etc/X11/xorg.conf
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Sun Feb 1 20:21:04 UTC 2009
[Code].....
View 3 Replies
View Related
Oct 31, 2010
I have been tasked to set up 2 monitors on SUSE Linux Enterprise that are a clone of each other, but each displaying different resolutions. The primary display has a max resolution of 1024x768 while the secondary display has a max resolution of 800x600.
The problem comes when the secondary display shows a "cropped" version of the desktop. Is there anyway to show different resolutions on each display while maintaining the proper desktop look?
[Code]...
View 4 Replies
View Related
Oct 29, 2010
I am not sure if this is the correct forum to post this topic (I was struggling between hardware and software). But since I do not think this was a problem with my hardware(monitor), I decided to post it here.
I have been tasked to set up 2 monitors on SUSE Linux Enterprise that are a clone of each other, but each displaying different resolutions. The primary display has a max resolution of 1024x768 while the secondary display has a max resolution of 800x600.
The problem comes when the secondary display shows a "cropped" version of the desktop. Is there anyway to show different resolutions on each display while maintaining the proper desktop look? I have attached the relevant portion of my xorg.conf.
[Code]...
View 6 Replies
View Related
Mar 9, 2010
I am trying to set up dual monitors for lenny but nosuccess for the moment.
They were working fine for the same setup on ubuntu.
Using xrandr I get:
I read that virtual screen size could be the maximum part which is of no use in comparison to the current size.
So setting a virtual part in my xorg does not help much. If the above is right.
I have:
How to get the external monitor work in the extened screen mode.
View 2 Replies
View Related
Feb 19, 2010
I'm using dual-screen output with KDE 4.4 on my laptop. Is it possible to have the KDE panel on the external monitor if attached and back on the laptop's LCD panel as soon as the monitor is disconnected?
It seems that Plasma prefers the built-in LCD even if an external monitor is connected. I tried various settings with xrandr and also in the System Settings but none of them helped. The only way to move the KDE panel to the external screen is to disable the built-in LCD.
What I would basically like to do is to use the external monitor as primary in the office and the laptop LCD next to it as a second screen. When I'm traveling I'd like to use only the laptop LCD.
Is there also a nice way to switch between the screens? On the Internet I found a script for the "screen switch" key for IBM Thinkpad and modified it to work on my Dell. But it would be nice to have this also automatic: autodetect the monitor attachment/removal and perform a configured action. The KRandr doesn't seem to have such a feature. Is there anything I could use?
My system is: Kubuntu 9.10 with KDE 4.4 upgrade. Hardware: Dell Inspiron 1545 with Intel GM45 card.
View 3 Replies
View Related
Apr 13, 2010
I made the mistake of trying to install an nvidia graphics driver from the download.nvidia.com/opensuse11.2 repository. My card is a PCI quadro nvs 295 so looks like it should be supported. The installation and update of the kernel seemed to be successful, but for some reason sax2 doesn't seem to recognise the nvidia card, even when I run "sax2 -r -m 0=nvidia" and I'm stuck with the VESA framebuffer graphics default in /etc/X11/xorg.conf code...
I've found tons of threads on this kind of thing but I only seem to be making things worse trying to fix it. If anyone can give me a hint and fix my pathetic-looking desktop I'd be very grateful!!! At the moment nothing that uses opengl will work either
View 9 Replies
View Related
Apr 8, 2010
I have been using ubuntu for quite a long time, and for the first time, I am now unable to set nvidia drivers to work. I have just install ubuntu 9.10 amd64 on an AMD 64 athlong X2 with a GEForce 6500 nvidia card.
The only reason I need the proprietary drivers is to use two monitors.
I am going crazy, I have tested everything I have found on the web. I have tried all the nvidia drivers version, I have tried envyng, ... but nvidia do not work!!
I am trying Xinerama with nv, but it does not work either!!!
Here is my xorg.conf file in which I have tried to use nv driver to set dual monitor. X fails to load and it says that screen 0 is deleted, that devices are found but there are no matches in the config file. Any clue?
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
[Code]....
View 3 Replies
View Related
Jul 18, 2011
I have an 1TB hard drive, half of it for Windows XP SP3, another half for OpenSUSE 11.4. After installing OpenSUSE, it didn't take me much time to notice that there was something wrong with KDE: sometimes it loaded quite fast, as expected, but most of the time I'd have to wait around 1 minute in that loading screen. Then I updated the kernel, as well as KDE itself, but that didn't solve the problem.
After that I tried to start the system using Enlightnment, and it was lightning fast compared to KDE, however, I didn't quite like its interface, and for some reason GNOME refused to start. All that was too frustrating to me, so I gave up and have been using Windows for the last few weeks. Got sick of it now and here I am on OpenSUSE again. Oh, it feels sooo much better! BUT, I'm still with the same problem.
My specs are as follow:
Motherboard: Gigabyte MA78GM-S2H (with updated BIOS, version F11)
Processor: AMD Phenom X3 8450
Memory: 2GB
Videocard: Nvidia Geforce 8500GT (using NVIDIA proprietary drivers)
OpenSUSE 11.4
KDE 4.6.0
Did I forget anything important?
Ps.: I didn't have these problems with Mandriva 2010.2, which, if I'm correct, used the same KDE version.
View 9 Replies
View Related
Dec 24, 2010
I'm running openSUSE 11.3 64 bit KDE 4 standardI have two monitors attached, running simultaneously, nicely, all is well.But when I reboot I have to set them up again because the settings don't stick/endure through a reboot.The GUI configurator that I use is at Menu --> Config Desktop --> General --> Display.How do I save the underlying settings and re-invoke them at boot time, perhaps from the CLI? Or some quick process that will do the job.
View 8 Replies
View Related
Mar 15, 2010
I'm trying to install the nvidia drivers but it is not working.
lspci | grep VGA
02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3)
My xorg.conf looks like this:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[code]...
And after that my X is not working. And when i try sudo modprobe nvidia I get this:
FATAL: Error inserting nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No such device
View 2 Replies
View Related
Apr 20, 2011
Today I bought a new monitor (IPS236V) to use it to watch movies and tv while I'm working on the other one.. I thought it's the best to activate Xinerama which could be done easy via CCC. But I'm not able to change the resolutions now as these panels are disabled in CCC. The first monitor is set to its native resolution, but the second is something lower.How can I configure both monitors to there native resolution?
View 5 Replies
View Related
