CentOS 5 Networking :: Cannot Ping From DHCP Client On Eth1
Nov 24, 2010
I have a Lan with 100 computers with microsoft windows xp and vista on it, and I need to build a CentOS Primary domain control- PDC. So I am building a PDC , with samba 3.x +Ldap ( Light Directory Acess Protocol), with static eth0 and DHCP-server( Dynamic Host Control Protocol) on eth1.
Eth0 : 192.168.1.3
Eth1 : 192.168.1.5
Here is the configurations files:
== BEGIN uname -rmi ==
2.6.18-194.17.4.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
== BEGIN cat /etc/redhat-release ==
CentOS release 5.5 (Final)
== END cat /etc/redhat-release ==
== BEGIN getenforce ==
Permissive
== END getenforce ==
== BEGIN rpm -q yum rpm python ==
yum-3.2.22-26.el5.centos
rpm-4.4.2.3-20.el5_5.1
python-2.4.3-27.el5
== END rpm -q yum rpm python ==
== BEGIN ifconfig -a == .....
View 3 Replies
ADVERTISEMENT
Sep 21, 2010
I have openvpn tunnel setup between two CentOS servers. One of the CentOS servers also acts as a DHCP server for some client computers.
Server A= OpenVPN server
Server B= OpenVPN client (connects to Server A with OpenVPN)
The two CentOS servers can ping each other (172.16.0.0/24) via the tun0.
However, client computer connected to Server B (DHCP server) can't reach 172.16.0.1 (which is the OpenVPN server).
I think I am missing some routing in my "ip route show". Following is the full picture:
What command can I issue to get this fixed? something along ip route add?
There is no firewall service on both end. service iptables stop! I can't bridge eth1 and tun0 as DHCP server might mess up the other side. I can't do a push of "redirect-gateway def1" because then clients loose their IP as they send DHCP requests to Server A.
View 2 Replies
View Related
May 7, 2010
I have installed Centos 5 on a virtual machine (esx4i). I set it to obtain an IP address from the DHCP sever, which is a broadband router, it has been given an IP address of 10.10.11.159 the router is 10.10.11.1 but I can't ping the router and I can't get any access to the network! I have a SCO Openserver server on the same physical box and it works fine so I know the network card & cable is ok.
View 9 Replies
View Related
Sep 29, 2010
I need to set up my centOS computer as a firewall in my home network. Ive got 2 interfaces, eth0 and eth1. I want to allow and forward all traffic on eth0 and block all traffic on eth1 except ssh, ping(icmp) and DNS. How do I do this? Ive tried some editing in /etc/sysconfig/iptables but no luck.
View 1 Replies
View Related
Jul 23, 2009
I have Centos 5 installed on a PC in the local network. I have installed the RPM dhcpv6-client-1.0.10-16.el5.i386.rpm on this PC to configure it as DHCP V6 client. The RPM was installed successfully, and I have done modifications to the following files:
1. /etc/sysconfig/network, set the networking to yes.
2. /etc/sysconfig/network-scripts/ifcfg-eth1 set the BOOTPROTO=DHCP.
Now the problem is when I start the client on this pc as dhclient, it throws the following errors, and logs out after some time. All the network configurations were lost and the PC gets disconnected from the network.
[root@ServerB]# dhclient
Internet Systems Consortium DHCP Client V3.0.5-RedHat
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
[Code]...
View 4 Replies
View Related
Aug 23, 2010
I'm new to CentOS and has recently use it.
I'm looking for a way to configure DHCP client so it would dynamically set the hostname and register itself to a DNS server. I don't have access to the DNS server.
View 6 Replies
View Related
Oct 22, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address. When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
iface vlan100 inet static
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 6 Replies
View Related
Jul 1, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address.
When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 2 Replies
View Related
Mar 4, 2011
I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..
/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......
View 7 Replies
View Related
Mar 25, 2010
I am puzzled with trying to configure a linux (openSUSE) client to dhcp to eBox DHCP server. I am using dhclient to lease an IP address with dhclient eth0 -s 10.45.48.108 and get a response
openSUSE11232CL1 dhclient: DHCPDISCOVER on eth0 to 10.45.48.108 port 67 interval 4
openSUSE11232CL1 dhclient: DHCPOFFER from 10.45.48.108
openSUSE11232CL1 dhclient: DHCPREQUEST on eth0 to 10.45.48.108 port 67
openSUSE11232CL1 dhclient: send_packet: Network is unreachable
openSUSE11232CL1 dhclient: send_packet: please consult README file regarding broadcast address.
The server reports eBox141 dhcpd: DHCPDISCOVER from 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
eBox141 dhcpd: DHCPOFFER on 10.45.200.2 to 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
I interpret this as the server receives the request and the client accepting it but the lease does not last long and the connection breaks. what this could be and why the connection breaks? Or my undestanding is totally wrong on how it works and should work? And BTW, where is that README file that's referenced in the message I receive on the client?
View 2 Replies
View Related
Jun 14, 2010
I have static route for eth1:
[Code].....
eth1 (13.3.3.2) is connected to router port 2/0 (13.3.3.1). I am trying to ping from eth1 to router or vice versa. None of them is not working. Don't know what is problem. [root@perseus anvltest]# ping 13.3.3.1 PING 13.3.3.1 (13.3.3.1) 56(84) bytes of data.
3 packets transmitted, 0 received, 100% packet loss, time 2000ms
[Code]....
View 4 Replies
View Related
Oct 20, 2010
I have a linux machine with 2 ethernet ports(eth0 and eth1). eth0 is connected to a router which assigns it an IP address 192.168.1.2. eth1 is connected to a switch and I assigned it an IP address 192.168.1.254 using "ifconfig eth1 192.168.1.254 netmask 255.255.255.0 up". How do I ping eth0 from eth1?
View 5 Replies
View Related
Dec 2, 2010
I'm no expert on DHCP. My problem is that i have a CentOS 5.5 server on which i want to install a DHCP server. I have two NICs where eth0 has access to the internet and where eth1 should act as an DHCP server.
I have installed dhcpd and this is how my dhcpd.conf file looks like.
Code:
ifconfig looks like this
Code:
When i start dhcpd on eth1 i get no error messages but when i connect any devices to eth1 they don't get any IP. I cant find anything in any logs about devices trying to get an IP address. I dont have any firewall rules in iptables.
View 4 Replies
View Related
Dec 9, 2010
Fresh install of 10.04.1 server; installs seamlessly; finds network no problem.
However, establishing static connection is driving me batty. Will not take. I've reconfigured "interfaces" file several times. My fingers are numb ifdown-ing and ifup-ing and /etc/init.d/network restart-ing.
I have two files in /etc/network ... interfaces and interfaces~ (one static and the other dhcp). I can switch them in and out of play. The dhcp works and pings out like a champ. static is dead, just dead. Cannot ping router ... nothing.
View 5 Replies
View Related
Aug 19, 2009
5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
View 17 Replies
View Related
Jan 31, 2010
I've only been using linux for a few days so I don't know all the tricks. I'm pretty savy configuring windows networks however.My adapter is (according to windows) a: CNet PRO200WL PCI fast ethernet adapterLinux says it is a: 21x4x DEC-tulip compatible 10/100 EthernetI do seem to be getting an ip address from the DHCP router, but I cannout ping any other ips or connect to the internet.I've tried a bunch of different options, switching things back and forth, but it still doesn't work, and honestly i don't even know what some of the options mean.
ALSO, if this helps:
paladin:~ # ifconfig eth0
Eth0 Link encap:Ethernet HWaddr 00:08:A1:03:3C:99
[code]....
View 14 Replies
View Related
Jun 7, 2009
I want to install CentOS from netinstall CD, but it doesn't work for wireless connection, because it just looks up for eth0 connection. Well, I connected server to wired USB connection and it's named eth1. I want to use netinstall CD but using eth1 connection. Is there any way for doing it?
View 2 Replies
View Related
Apr 7, 2010
I am contemplating the use of DHCP options as a way of passing host-specific information to hosts that are booting disklessly from a network server. My intention is to have the DHCP client request certain options, and use the reply to configure the diskless hosts accordingly. The theory and rules behind all of this seem well documented on web sites such as die.net. However, the practical application of the protocol seems to be a lot less clear. What I am looking for is an explanation of what (existing, I hope) tool(s) are used, and how they are applied so that I can grab information from the DHCP server, and use it in userspace scripts or other programs. Specifically, my intention is to use a locally defined option that would give a host-specific directory name or filesystem to use by the diskless host to obtain host-specific applications and configuration data.
So far, all of the DHCP client documentation I've found relates to the usual function of assigning IPs, etc. I've looked at dhclient-script on a Redhat system and can't figure out the relationship between it and the dhclient program. Clearly, the script is invoked somehow by dhclient, but I don't understand where the transfer of data received from the server gets into the script. Does dhclient just create a list of exported environment variables the child script then gets access too? What are the rules for how variables are created and what variables are created?
View 7 Replies
View Related
Aug 4, 2010
I have an embedded device for which I've created an html configuration page. This page allows you to set static IPs, dhcp, and can scan for wireless devices.My problem is that in order to access the device it requires that it runs as a dhcp server otherwise people are not assigned an IP and so can not access the embedded devices static IP. (This config page is for the laymen and so they are not the type who are able to set up their own static IPs). One of the potential options is to have the device connect to the network on eth0 acting as a dhcp client. However this prevents me from running a dhcp server.One solution I can think of is running a dhcp server only if it doesn't detect another dhcp server running on the network.
View 4 Replies
View Related
Jun 1, 2011
I want to use dhcpcd instead of dhclient on Ubuntu. The 'interfaces' man page say: "The dhcp Method This method may be used to obtain an address via DHCP with any of the tools: dhclient, pump, udhcpc, dhcpcd. (They have been listed in their order of precedence.)"
I can't find where to change this default order. I can uninstall dhcp3-client, but this will also remove ubuntu-minimal, which is not a good solution.
View 2 Replies
View Related
Nov 5, 2010
I would like to use dhcpcd instead of dhclient in my Debian installation, because I had some trouble with dhclient in the past and I assume the problem is still exists now with some equipments.
So I would like to use dhcpcd, but I couldn't find a way to tell the system to give higher priority to dhcpcd than dhclient.
Also, I've tried to remove the package 'isc-dhcp-client', but it also would like to remove the following packages: isc-dhcp-client knm-runtime network-manager network-manager-kde
Moreover, it says no need the following packages anymore: usb-modeswitch dnsmasq-base libnm-util1 usb-modeswitch-data network-manager-ppp pptp-linux network-manager-openvpn libnm-glib-vpn1 libnm-glib2 modemmanager vpnc network-manager-vpnc
I would like to still be able to use kde-network-manager, because it is much easier to manage wifi connections using this interface.
View 2 Replies
View Related
Jan 26, 2011
Is there any way to get an async notification (perhaps through something like a Linux message queue or Unix socket) when a DHCP client is either unable to renew its lease, or the address obtained changes from the previous value? I've got the ISC client and will dig into it to determine if it supports such a feature, but thought I'd ask here in parallel. (I'm trying to find out if there are any DHCP clients out there which already support this capability.)
If you're curious: We have an application where we're doing auto-registration of an IP camera to an external server. If the camera's dynamically assigned address changes, we need to restart the auto-reg state machine. I've seen implementations where a socket is opened and a SIOCGIFADDR ioctl used to fetch the IP addr, but I'd sure like to avoid polling like this if possible.
View 1 Replies
View Related
Oct 31, 2010
I have an embedded device for which I've created an html configuration page. This page allows you to set static IPs, dhcp, and can scan for wireless devices. My problem is that in order to access the device it requires that it runs as a dhcp server otherwise people are not assigned an IP and so can not access the embedded devices static IP. (This config page is for the laymen and so they are not the type who are able to set up their own static IPs). One of the potential options is to have the device connect to the network on eth0 acting as a dhcp client. However this prevents me from running a dhcp server. One solution I can think of is running a dhcp server only if it doesn't detect another dhcp server running on the network. However I have no idea how this could be setup.
View 2 Replies
View Related
Nov 1, 2010
i hav configure dhcp server. but the ip is not getting assigned to my client machine.
View 3 Replies
View Related
Mar 20, 2009
Code...
What I can ping
Host A -> Host B
Host B -> Host A
Host A -> Router B
Host B -> Router A
Host A -> OpenVPN B
Host B -> OpenVPN A
VPN Server -> VPN Client
VPN Client -> VPN Server
What I can't ping
VPN Server to any client side host local address
VPN Client to any server side host local address
I have searched and searched for this but can not find any answers. Why can I not ping Host B from my OpenVPN server?
View 1 Replies
View Related
Mar 28, 2010
After I applied below iptables rule.. I am unable to ping the host in 172.16.1.0/24 from OpenVPN client
View 1 Replies
View Related
Jun 5, 2009
i have installed centos 5.1 but it won't recognize 2nd nic card (eth1). i was unable to install the driver supplied by the cd. i am using intellinet gigabite pci network card. the network card recognize by centos 5.3 but i need to use centos 5.1. i also tried another intel gigabite adopter but it also won't recognize by centos 5.1.
View 2 Replies
View Related
Jul 15, 2011
I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
View 2 Replies
View Related
May 7, 2009
Centos 5.3 How can I change the primary nic from eth1 to eth0? My board has 2 nic's and I'm having license issues with cpanel
View 2 Replies
View Related
Sep 24, 2009
I have added a new network card on my Cent OS machine. This is a RTL-8139/8139C/8139C+ card. When the machine boots or I start the network it displays "eth1 does not seem to be present,delaying initialization."I have gone through different posts on the forum with similar problems and have posted output of some of the commandsOutput of lspci is
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10)
[code]....
View 8 Replies
View Related
