Ubuntu Multimedia :: Elgato / Lsusb Shows The Device But Don't Get A Vendor Name?
Jan 3, 2010
I'm really trying to get the Elgato Eye TV Diversity working with Ubuntu (I'm trying it on both Karmic and Hardy)
The problem is, lsusb shows the device but I don't get a vendor name, just an ID.
dmesg shows a usb device being detected, but not that it's a TV tuner.
I've followed the guides on these pages:url
url
url
url
P.S (I know some of the guides are for the hauppauge nova, but this is the same device as far as I can tell)
View 5 Replies
ADVERTISEMENT
Jan 17, 2010
I installed mythbuntu 9.10 this week on some old hardware, I had a Hauppauge 500MCE PVR in and made it work fairly easy. I'm used to gentoo
However, I want to record HD signal, so I plugged in a Eyetv hybrid and followed this guide url.
I extracted the driver, put it in into /lib/firmware, modprobed em28xx, rebooted. When I plug in the device, it is not recognised. I tried both usb ports. The ID is "0fd9:0018", which is somewhat different from similar hardware e.g. Hauppauge wintv-hvr-950 (ID 2040:6513 url.
I think the hardware has been updated, hope someone knows how to crack this one
I have added some additional information below!
# uname -a
Quote:
Linux m 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 GNU/Linux
# lsmod | egrep -R "video|em|video|v4l"
Quote:
em28xx 80968 0
ir_common 48512 1 em28xx
videobuf_vmalloc 6496 1 em28xx
videobuf_core 17952 2 em28xx,videobuf_vmalloc
v4l2_common 17500 6 em28xx,wm8775,tuner,cx25840,ivtv,cx2341x
code.....
View 4 Replies
View Related
Jan 6, 2009
I am new for Linux, my job is developing USB device on fedora Linux.The USB device driver has been completed successfully.my question is:how can I apply a new vendor Id (VID) for fedora kernel, so that my latest driver will be updated automatically when the Linux kernel was updated.
View 1 Replies
View Related
Mar 3, 2010
In Kaffeine I can not press "Start scan" button, because it is disabled. The USB-ID of the DVB-T dual-tuner device is 0fd9:0011.
View 5 Replies
View Related
Sep 5, 2009
When I connect my Treo 650 with a USB cable it works sometimes and not others. A little investigation showed
that it always works when I see the Palm device listed in the output of lsusb. While trying to diagnose why it appears sometimes and not others, I discovered that it sometimes appears in /proc/bus/usb/devices and not
in lsusb. I didn't think that was possible!
I've tried running kudzu (the Red Hat hardware discovery tool) and killing and restarting udevd.
View 2 Replies
View Related
Sep 8, 2010
I need a way to find out what my dhcp vendor-class or vendor string is on a device. I want to take a client and based on the vendor string (if I can get what that string is) set up a pool for it.
View 1 Replies
View Related
Jun 23, 2010
I a m using a logitech c250 and it works perfectly on ekiga when i use ekiga i get video and the little green indicator turns on but I really want to use the webcam for stickam and the minute i turn Ekiga off the indicator goes grey and it stopps working i've used to codes, lsusb and lspci to detect my webcam and it they worked but my problem still isnt fixed.
View 4 Replies
View Related
May 8, 2011
I have a fresh install of Natty and i'm having some issues getting sound to work. My laptop has a built in sound card which works just fine. However, i also have a usb 5.1 sound card which isn't working at all. Both devices show up in 'Sound Preferences' but when i select the 5.1 device as the output device sound doesnt work. I ran the alsa-info.sh script and the output can be found here.
View 4 Replies
View Related
Aug 3, 2010
I have a problem making work a webcam. At the begining, after the instalation of 10.04 in a new laptop, the webcam did not work but with a lsusb I see that the webcam was Webcam 5986:0241 acer. I was not able to config neither use the webcam with any application. After lots of test and forums reading I could not do my webcam to work, and now when I do a lsusb my webcam does not appear.
View 1 Replies
View Related
Oct 21, 2009
I just noticed, on both of my CentOS 5.3 servers, within grub, root shows (fd0)device.map = (hd0) /dev/sda and nothing else.
View 4 Replies
View Related
Apr 13, 2010
All my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?
View 3 Replies
View Related
Mar 7, 2010
what is the lsusb equivalent of lspci -k?
View 1 Replies
View Related
Apr 13, 2011
I'm currently setting up a dell server with hardware raid 1 on sas 6r. i got 4 sas installed on the server and configured to raid 1 as stated below,
array 1:
slot 0 & 1
array 2:
slot 2 & 3
during the installation, the installer detect the array 2 as sda and array 1 as sdb.. so i proceed with installation on array 2. after completed the installation, the first reboot lead me to a 'grub-rescue" prompt. by following the guide at url Mode, i've noticed that the boot folder has changed to (hd1,1), which i believe it has changed to sdb1. default root device shows that prefix=(hd0,1)/grub.
View 3 Replies
View Related
Feb 24, 2010
I've been having some trouble getting my two external USB hard drives to mount on boot. They are not recognized by lsusb after a boot, but after they are power cycled or unplugged & replugged they will show up in lsusb and mount. One odd thing I noticed was that when one of the drives was moved to a different port before booting it would be recognized for that boot onlyI have tried adding usb_storage to /etc/modules and doing a update-initramfs to my kernel (2.6.31-14) to no avail.
Since I started having this problem, I have reinstalled ubuntu on a different internal drive, and this did not fix it.I'm not sure if this matters, but the UUIDs of the two drives are identical. I would try reformatting one of them but its quite inconvenient. My /etc/fstab is set up to mount them using their labels (ex1 and ex2) rather than the UUID, and I can mount them both at the same time
View 5 Replies
View Related
May 30, 2010
I did searched you tube but my results were not great.I have 2 books on KernelProgramming.I feel I need if some where I can get a video tutorial which can help me to understand how to develop a Linux Device driver that will be great.I had a look at Greg Kroah Hartmans video lecture of developing patches on ......I have been reading books and a lot of stuff.So I wish if I could get a video lecture that would be better
View 1 Replies
View Related
Oct 30, 2010
I'm running Squeeze and I'm looking 3 days now for a solution in some weird problem. The NetworkManager Applet shows that there isn't connection although I am connected. The icon has this small "x" and when mouseover it says "No network conncection". Moreover when left clicking it, it says
"Wired Network Device not managed"
While I was looking for the solution a came across this post by an Ubuntu developer who says:network-manager-applet displays the connectivity state of network-manager's managed interfaces not every interface. So the title "network manager says disconnected but is connected and working" is actually misleading. The interface is connected and working but not from network-manager's point of view since it is not managing the interface. Additionally, in Lucid now network-manager applet displays nothing now for non-managed interfaces so is less misleading. You can check to see whether or not an interface is managed by network-manager by using the command line too nm-tool. You'll see "State: unmanaged" for unmanaged interfaces.
View 14 Replies
View Related
Jun 20, 2011
I have used the information available at wiki.debian.org/iwlagn to install firmware etc for my Intel Pro Wireless 4965 card.According to the network applet the connection is good, but it only seems to work when my ethernet cable is plugged in.I get no connection without the cable in, even though clicking on "edit connections" showshat ethernet is shown as "device not managed".With the cable plugged in I can get emails. Iceweasel will connect to the internet, but Epiphany will not.Without the cable I get no internet connection at all
View 9 Replies
View Related
Apr 6, 2010
i am using a alienware m17x QX9300 ATI 4870 CrossfireX 1920x1200p and till now was working fine with ultimate on it,now i don't know what happen ,before open the login screen is telling me that he has to start with low resolution,and after login sometimes is freezing.when i try to open display to set the resolution is giving me this: It appears that your graphics diver does not support the necessary extensions to use this tool. Do you want to use your graphics driver vendor's tool instead? and if i press yes is giving me this: There was a problem initializing Catalyst Control Center Linux Edition. It could be caused by the following. No ATI graphics driver is installed, oor the ATI driver is not functioning properly. Please install the ATI driver appropriate for you ATI hardware, or configuer using aticonfig Here's my /etc/X11/xorg.conf file - maybe there's some weirdness in it :
Section "Screen"
Identifier"Configured Screen Device"
Device"Configured Video Device"
SubSection "Display"
Modes "1920x1200"
Virtual1920 1200
EndSubSection
EndSection
Section "Device"
Identifier"Configured Video Device"
EndSection
View 1 Replies
View Related
Jan 21, 2010
why 'lsusb' doesn't list anything, Puppy 4.3.1
View 3 Replies
View Related
Jul 8, 2015
On my Linux (Debian/Ubuntu), I can get the PRODUCT of a library with "apt-file search" or "dpkg -S".May be I can get the VERSION by parsing the name of the library.so.But, How can I get the VENDOR ???
View 1 Replies
View Related
Mar 15, 2011
what is the vendor lock
View 9 Replies
View Related
Nov 14, 2010
I plug in my Maxtor 1TB external USB drive, and here's what dmesg says:
Code:
[ 82.480054] usb 3-2: new full speed USB device using ohci_hcd and address 7
[ 82.660052] usb 3-2: device descriptor read/64, error -62
[ 82.950076] usb 3-2: device descriptor read/64, error -62[code]...
lsusb produces no results, and "fdisk -l" yields nothing as well.The drive is not recognised as /dev/sdb1 as it was until yesterday.
View 7 Replies
View Related
Sep 1, 2011
I can get the command program to work, but not the desktop program to work. Windows Wireless Driver was working, but now every time I try to start it, it won't load, and will just be an empty window. This happened after I tried to installed a driver (which was the wrong one), and I restarted the computer. After this happened, I tried to reinstall the program, but to no avail.
The command program works, but I can't use the command lsusb, because it just pauses and doesn't do anything. Do I have to wait for it to kick in. I'm pretty sure that this is not it, because when I try the lspci, this works fine (but it's not the one I need). Please help, and don't make any stupid replies.
View 3 Replies
View Related
Jun 21, 2011
trying to configure an old Epson LX 400 dot matrix printer with cups. I really need this printer to print vauchers. System is Debian SID, latest cups 1.4.3 cups was recently change to reject lsusb printing and now uses libusb. lsusb sees printer, but does not name it:
$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 1a40:0201 TERMINUS TECHNOLOGY INC.
[code]....
View 2 Replies
View Related
Jul 20, 2010
I have been administering linux systems for years now, but usually they are commodity boxes and as a result I rarely have driver problems, short of needing to install some "restricted" or "proprietary" driver package, or manually installing the nvidia binary drivers back in the day. However, one question to which I have never picked up a straight answer regards common troubleshooting practice. Will lsusb and lspci list device for which a system has no drivers (kernel modules)? I am trying to install a webcam on a SiS-chipset laptop and though I can see a physical webcam, neither lsusb or lspci are showing me that any webcam-like device exists. What I want to know is if it would show anything, or if it needs drivers in order to show a device?
View 4 Replies
View Related
Dec 28, 2010
I just installed a new GT240 w/HDMI and I have a new Vh232H monitor w/HDMII connected the video card and monitor via HDMI cable and started the computer.Nothing.The monitor is not getting a signal via HDMI.
View 1 Replies
View Related
Aug 3, 2010
I have been trying to figure this out for a long time now and can't seem to get it to work. I have three serial ports I need to communicate with. The first one works, but the other two, which have identical product and vendor IDs, do not. This is what I have so far under /etc/udev/rules.d/10-local.rules/
[Code]....
View 14 Replies
View Related
Feb 7, 2011
I have a Huawei E122 Mobile Broadband HSPA USB Stick on three ireland. i can't get it to connect. but i think the problem might be, when i stick it in nothing happens. it doesn't show up under lsusb. i don't think it "mounts"
View 2 Replies
View Related
Jun 2, 2011
I am trying to build a jar file using a ant script provided by a vendor and while running the script, I am getting the below connection time out error when it tries to download a jar file.
Code:
C:ccuapi-java>ant run
Buildfile: build.xml
get_libs:
[get] Getting: http://download.java.net/maven/2/args4j/args4j/2.0.12/args4j-2.0.12.jar
[get] To: C:ccuapi-javaargs4j-2.0.12args4j-2.0.12.jar
[Code]...
View 4 Replies
View Related
Jun 30, 2011
I am running CentOS 5.6 on my servers (auto-updating to the latest patches). A couple of days ago, a number of updates were applied:
glibc-common-2.5-58.el5_6.4.x86_64
glibc-2.5-58.el5_6.4.x86_64
nscd-2.5-58.el5_6.4.x86_64
glibc-headers-2.5-58.el5_6.4.x86_64
[Code]...
This update broke a software tool from Xilinx (FPGA compiler). I rolled back all of the above, to 2.5-58.el5_6.3, and the tool works OK. I get:
/home/cad/xilinx/ISE13.1/ISE_DS/ISE/bin/lin64/unwrapped/map: symbol lookup error: /home/cad/xilinx/ISE13.1/ISE_DS/ISE/lib/lin64/libXst2_Core.so: undefined symbol: _ZN5boost7archive6detail17basic_oserializerD2Evmake[2]: *** [map] Error 127
View 1 Replies
View Related
