I am on an IBM thinkpad t43 using backtrack 4 r2. Wireless works in windows (/dev/sda1), openSUSE 11.3 (/dev/sda2), but not backtrack (sda3)
Code:
#cat /proc/pci
02:02.0 network Controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network
[code]...
Running 10.10RC on an IBM Thinkpad T43. My wireless drops out intermittently, it could DL a gig or two fine then without any warnings just drops, I have to reboot. Here is the lspci, its using ipw2200 driver.
0b:02.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
Subsystem: Intel Corporation Device 1011
Flags: bus master, medium devsel, latency 64, IRQ 21
Memory at b4001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Kernel driver in use: ipw2200
Kernel modules: ipw2200
From var/log/messages
Oct 6 11:25:12 cisco-thinkpad kernel: [74828.021204] ipw2200: Firmware error detected. Restarting.
Oct 6 12:00:44 cisco-thinkpad kernel: [76959.435841] lo: Disabled Privacy Extensions
Oct 6 12:01:22 cisco-thinkpad kernel: [76997.835485] WARNING! power/level is deprecated; use power/control instead
My system hangs within a few minutes after I turn on the Intel Pro/Wireless 2915ABG interface built into my motherboard or if I boot with the interface turned on. I have been having this problem for a couple of years and tried to fix it myself from time to time. (I think that I even asked for help in the Forum once.) The wireless interface used to work fine with Ubuntu and I kept hoping that the problem would "magically" disappear with each upgrade. I also read about the recent problems with ndiswrapper and similar interfaces. But this doesn't seem to be my problem. The entries in /var/log/messages just prior to the last hang were
Dec 15 09:09:47 periwinkle rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'.
Dec 15 09:09:47 periwinkle rsyslogd: [origin software="rsyslogd" swVersion="4.2.0"
[code]....
I don't know what process gdb was trying to trace. Since I was testing the system, I was only running Firefox, which has always triggered the problem. The output from "dmesg | grep -e ndis -e ipw" was
[ 19.121563] libipw: 802.11 data/management/control stack, git-1.1.13
[ 19.121566] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 19.161180] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[code]....
In previous version of Ubuntu, the messages just before the hang used to complain about the firmware in the interface being buggy. I intended to send the output from iwconfig and "sudo iwlist eth1 scan" as well. But I can't turn on the interface without hanging the system and thereby destroying this post.
I just upgraded from the 64-bit version of Ubuntu 10.4 to 10.10 over the network using the Update Manager. But when I chose the "About Ubuntu" option from the System menu, I was surprised to see it say that I am running Natty Narwhal 11.4. My system is a Linux Certified LC2464T [URL]
I have installed Fedora 12 on my laptop and subsequently spent most of the day trying to get the wireless connection to work. Looks like I am not alone with Wireless issues Through searching and reading today I think the problem lies with the fact that the wireless on/off switch is not working. Under Windows, when I press the wifi toggle switch it starts flashing orange. I haven't managed to get it to do anything under Fedora.
# lspci | grep Wireless
06:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
# iwconfig
[code]....
When I log in to linx and connect to my University's public wifi, it disconnects or if it stays connected, I cannot ping anything or load any webpages. But when loggod in to windows I can write this message now. Signal strength is 28% Can anything be done to still use wifi in linux and not have to log in to windows?
View 3 Replies View RelatedI use this Thinkpad mostly for work while traveling, and wireless connectivity is not a big issue for me. Battery life is a big issue, however. I've just converted from Mandriva. With that, I was able to disable the wireless adapter so that it did nothing at all on boot - and only started on my instruction. This made a dramatic difference to battery life! How to achieve this in Ubuntu? The file attached gives all the info about my wireless set-up as it stands.
View 7 Replies View RelatedI have an IBM Thinkpad T60, running Ubuntu 10.04 (Lucid) with a dual boot of Windows XP. I am having trouble getting it to connect to my home wireless network, which uses WEP. It connected fine at my university when I first installed Lucid, but has not connected at home. I can see the network in the panel applet, with a good signal strength, but when I try to connect it repeatedly asks me for my key and never actually connects. I had this problem shortly before I installed Lucid, though it was working for a long time previously. I'm not sure what update caused it to stop working because I was at my university at the time, and it works fine there even now, so I didn't realize it right away.
I doubt this is a hardware issue because I can connect to the same network when I boot into Windows. I have seen posts about similar problems on the forums, but couldn't find any solutions that helped me.
Below is the information the wireless help guide said to post. Machine Brand and Model: IBM Thinkpad T60
Wireless Brand, Model, and Wireless Chipset: lspci -nn | grep 'Wireless'
Code:
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4227] (rev 02)
Check Interface:
ifconfig wlan0
[Code]...
I'm trying to set up ubuntu on my netbook, the brand and make is obscure, essentially, this is a no-name brandless build from china, but a pretty decent lappy. Atom N270 Intel 945GSE based. initially it was equipped with a 3DSP wifi/bluetooth mPCIe combo card, which is proprietary and didn't work on ubuntu (didn't even show up as a device), so I got an intel 4965agn based on compatibility list somewhere in the wiki.
The problem I have is that I see networks, but can't connect at home or at work or anywhere, it just hangs in the connecting status and then throws the authentication popup at me again (pw is all correct). I tried looking around at similar problems, some have wpa_supplicant related issues, but doesn't seem to be the same as mine.
I tried creating an unsecured network using my macbook's airport, and same thing happened with ubuntu... hangs in connecting status then drops, so it doesn't seem to be WPA. I don't have the device on me to do all the iflist iwlist checks for you, but if you could give me some clues, I'll post back when I get home.
I'm using this card on a Toshiba Tecra M3 laptop. Firmware is installed. iwconfig shows the following:
Code:
eth1 radio off ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
[code]...
working to sort out the damn wireless for too long. Mine in cent05 5.2 . network manager is on and I can see the icon on tray. It list all the wireless connections too, but just won't connect. WPA encry is disabled. further details below:
# lspci | grep Wireless 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
# ethtool -i eth1
driver: ipw3945
version: 1.2.1dm
firmware-version: 14.2 1:0 ()
bus-info: 0000:0c:00.0
[Code]...
Intel 5100 wireless card doesn't connect on 10.04?
View 1 Replies View RelatedI cant seem to understand what happens to my wifi networking, i just installed ubuntu 10.10 today (completely erasing windows) on my toshiba satellite m645. Seems like my wireless card (the specs say its intel 802.11a/g/n wireless LAN) will only randomly detect the available networks or will connect only for a few seconds just after i just turned it on, then it will disconnect.
View 2 Replies View RelatedIntel wifi link 5100 not found on sony vaio backtrack 4 vmware I use vmware to load backtrack I have a sony vaio with 5100 AGN wifi card installed in it. I had tried anything to make my wifi work but always show no interface no wireless. I googled it for help for weeks and all i get was download the iwlwifi things and i already installed in it. i even tried many other thing
/etc/init.d/wicd start
/etc/init.d/networking start
and everytime i type ifconfig it just show eth and lo and no wlan0 in it everytime i type airmon-ng there are no chipset interface and ...........thing (forgot) I could find my wireless card name when i type ilg... something i forgot The problem is,i think my linux doesn't reconize the card even i have installed the driver Anything that i can do to make my linux reconize wifi link 5100 agn wireless card?
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
Are Intel wireless cards compatible with non-intel-based laptops? In my case I wish to upgrade the current Atheros-based mini pci express wifi card with the Intel 4965agn. It is an Asus 4520 with an AMD Athlon X2 processor and nvidia nForce chipset.
View 1 Replies View RelatedI have installed backtrack 3 on vmware workstation. I would like to install a TP-link TL-WN650G wireless card(atheros based - AR5005GS) onBacktrack because that it supports packet injection. Backtrack doesn't automatically recognize the device so I need to install the driver, I have done some research and found I needed to install the driver 'madwifi-old'(ieee80211 version) from here..http://aircrack-ng.org/doku.php?id=madwifihttp://madwifi-project.org/However I have no idea how to install them from inside backtrack, so if someone knows please let me know.
View 1 Replies View Relatedi installed backtrack recently....and wireless networks are not detected.... which deb to install because it is based on ubuntu 8.10
View 1 Replies View RelatedI just changed over from Ubuntu to Debian Squeeze and now my WiFi doesn't work. My computer is a Toshiba Satellite and the wireless card is Intel 2200bg. I think that's the name of it. That's the driver, anyway. My router is using WPA2, and using iwlist scan, I can see the network just fine. When I try to connect, though, it starts to connect for a while, says it's validating authentication, then says it fails. I've triple-checked my password and it's right.
View 9 Replies View RelatedI moved to Berlin recently and I got wireless internet through an access point. I'm supposed to use the laptop's built-in wireless netcard to access the internet. This usually works in windows (connection falls out from time to time), but I have yet to make it work in linux. I'm using OpenSuse 11.3 64-bit and the Knetwork manager. Most of the settings in the network manager are correct, but it keeps wanting to use system certificates for the server. By that I mean it keeps checking 'Use CA System certificates'.
So I can't choose the CA-certificate supplied by my internet provider. I keep removing the check-mark and pointing it to the 'hotzoneCA.der' certificate. I also got a 'personal' certificate, in lack of a better word. Its called 'jacob_collstrup.p12'. The Knetwork manager seems to accept the 'jacob_collstrup.p12' certificate, but not the other one.
I just put the certificates in a folder like this /jacob/home/hotzone/zertifikate/ I can see the network fine using the Knetwork manager, and the signal strength seems ok. Not too good, but it shouldn't be a problem. I might have messed up the system, since I first tried this guide, prior to experimenting with Knetwork Manager:
1. (had to run this one as su)
Code:
wpa_supplicant -w -i wlan0 -c /etc/wpa_supplicant.conf -Dndiswrapper -dd �t
2. (This was supposed to be put in a wpa_supplicant.conf file)
Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
opensc_engine_path=/usr/lib/opensc/engine_opensc.so
pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so
[Code]...
I have lenovo thinkpad, T61 with Intel 4965AGN wireless card. It is a N card, it works under N mode in windwos, but not in Ubuntu (10.10). I installed ndiswrapper and got the windows xp drivers for this card. the issue is that i got an error when installing the drivers and since then I cannot use wireless.
The error i got is: Code: Module could not be loaded. Error was: FATAL: Could not read '/lib/modules/2.6.35-24-generic/kernel/ubuntu/ndiswrapper/ndiswrapper.ko': No such file or director I unistalled the driver, but now under network connections no wireless connections appear, nothing. I cannot use wirless anymore.
trying to connect wireless on wlan0 intel pro wireless 4965 AG or AGN
View 1 Replies View RelatedI can't get my card Intel Wireless 5300 AGN to work. I'm running Slackware 13.1 and it's a full, fresh install.I get to show up with lspci -v:Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection...But it will not show up with 'ifconfig' which will only list the local loopback (yes we have have a eth problem as well but one thing at a time).
View 5 Replies View Relatedi cant connect to the internet with backtrack. set up my wireless card so i can connect?
View 2 Replies View RelatedI have an old Toshiba Satellite A30 Notepad. I've installed Ubuntu 10.04 onto it and everything but WiFi works. I've installed wicd and several other network tools but just can't get Ubuntu to let me use the WiFi connection (the option is greyed out).I know the card works because the last OS (Windows XP) used it without any problems. The card is detected, the drivers are installed and the hardware (slider) switch is set to on.I think the issue is related to the Radio Frequency Kill Switch being on but I don't know how to turn it off.The output from various commands are:
sudo lshw -C network is:
Code:
*-network:0
description: Ethernet interface[code]............
I have a Dell Inspiron 6400 with Windows 7 and Ubuntu 10.10. I cannot connect to the internet. My wifi light is on, but it'll flash?
View 9 Replies View RelatedI'm running Linux 11.04 and my wireless network was working just fine until today. I cannot connect to WiFi - it acts as if the device wasn't there. The hardware switch led isn't working. No matter how much clicking on it, it won't work.
iwconfig:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm
[Code].....
I use backtrack 4 in my acer aspire one notebook and i want to connect to my mail account from terminal!Could someone tell how can i do it??
View 10 Replies View RelatedMy wireless (Toshiba laptop, 10.04 64 bit) is just hanging when trying to connect. It was working fine but now nothing. My Wireless antennae is on and my other laptop can connect with no problems. I have restarted the router and the laptop twice.
View 1 Replies View RelatedI am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.
View 9 Replies View Related