Hardware :: Prism Firmware Timing Out On Inventel UR054g
Apr 8, 2010
I can't bring up an Inventel UR054g usb card id 1435:0427 with Slackware 13 custom kernel 2.6.32.4 SMP
Using firmware 2.13.24.0.lm87.arm (supposed to work) gives a time-out
dmesg:
Code:
[ 6611.484643] usb 1-2: firmware: requesting isl3887usb
[ 6611.488702] phy11: p54 detected a LM87 firmware
[ 6611.488705] p54: rx_mtu reduced from 3240 to 2384
[Code].....
I've tried using other firmwares and also extracting them myself from the windows drivers; always gives a time-out.
Used this card before with Slackware 12 and worked correctly
View 8 Replies
ADVERTISEMENT
May 27, 2010
I'm mad at my ignorance and hope some of you will be able to put me out of my misery I have an IBM X22 with Prism 2.5 Wavelan PCI chip with old firmware, which I want to renew in an attempt to get the Wifi working. Here the output of hostap_diag <wlan interface>:
NICID: id=0x8013 v1.0.0 (PRISM II (2.5) Mini-PCI (SST parallel flash))
PRIID: id=0x0015 v1.0.5
STAID: id=0x001f v1.3.3 (station firmware)
View 2 Replies
View Related
May 14, 2010
Here is how I got flash to work in prism. Prism was working fine with flash in 9.10 but the 10.4 install caused it to stop working. After doing all of these with no success I decided to open up a terminal and see what the problem was.
Here is what I did prior to finding the problem:
- Purged and reinstalled flash
- Cleared my website storage cache from flash
- Deleted all shortcuts to Prism
- Deleted Prism settings (~/.prism) then purged and reinstalled Prism.
Finally, I decided to open up a terminal and see what was going on. I made a dummy Prism app on my desktop then copied and pasted the 'command' from the properties (right click > properties).
I pasted that in a terminal:
Code:
tye@T:~/Desktop$ "prism" -override "/home/tye/.webapps/dummy@prism.app /override.ini" -webapp dummy@prism.app
It gave me the following output:
Code:
Attempting to load the system libmoon
Segmentation fault
So, knowing that libmoon is part of moonlight I performed the following:
Code:
tye@T:~/Desktop$ aptitude search moonlight
which provided me with this (omitting unimportant results)
Code:
i A moonlight-plugin-core
- Free Software clone of Silverlight 2.0 - plugin core components
i moonlight-plugin-mozilla
- Free Software clone of Silverlight 2.0 - Xulrunner 1.9 plugin
So, I removed the packages and any related packages, like so:
Code:
tye@T:~/Desktop$ sudo apt-get purge moonlight-plugin-core moonlight-plugin-mozilla && autoremove
Made a dummy prism app! Prism was working. So there you have it, moonlight is currently breaking prism. For now uninstall it if you want flash apps to work in prism.
View 1 Replies
View Related
Apr 21, 2010
so its not that difficult after all - just use PRISM!log into hotmail on your browser - copy the http: line and add it to PRISM then add your login detail and Voila! all ready to add to the task bar!ok so not the most in depth how-to but if youve been messing about with all the different email apps using Prism will be childs play! if not just message me and ill add more detail.
View 2 Replies
View Related
Apr 15, 2011
can't find the prism package in natty. what happend to it? is there anything that replaces prism in natty? i have used prism in combination with the compiz widget layer for certain webpages i had to have on every desktop. was very handy indeed.
View 2 Replies
View Related
May 31, 2010
I've just installed Ubuntu 10.04 on my old X30 alongside my fully working 8.04 and have strange wifi problems under 10.04 (under 8.04 it worked out of the box):
- no available networks are shown
- running "sudo iwlist scanning" results in "eth1
Interface doesn't support scanning : Device or resource busy"
- without any wireless configuration from my side I get this:
sudo iwconfig eth1
eth1 IEEE 802.11b ESSID:"gxC6isQxFFJxEC)xCDxBAxAB
xF2xFBxE3F|xC2TxF8x1BxE8xE7x8DvZ.c3x9FxC 9x9A"
Mode:Managed Frequency:2.467 GHz Access Point: None
Bit Rate:11 Mb/s Sensitivity:1/0
Retry short limit:8 RTS thrff Fragment thrff
Encryption keyff
Power Managementff
Link Quality=90/70 Signal level=-8 dBm Noise level=-147 dBm
Rx invalid nwid:0 Rx invalid crypt:63 Rx invalid frag:0
Tx excessive retries:1 Invalid misc:0 Missed beacon:0
A very strange ESSID there appearing out of nowhere...
View 9 Replies
View Related
Jul 4, 2010
I can't my system because of this error: Code: linux-firmware: /lib/firmware/radeon/R700_rlc.bin exists in filesystem Note that in the beginning, it asks:
Code: :: Replace kernel26-firmware with core/linux-firmware? [Y/n] There are so many updates by now that the list fills in a few pages in the terminal! Also, I wonder why so many Arch updates get stuck or broken compared to almost any other distro? Is it poorly designed packages? Is it a design flaw in pacman/the package format?
View 6 Replies
View Related
Jun 4, 2011
after installing Ubuntu Natty Narwhal 11.04, I'm experiencing tons and tons of complications with the wireless Internet connection. I have solved most of them. Now I have only one thing left. When I hit the drop-down menu for wireless connections, it says "Wireless connection (Firmware missing)"
I have installed the driver for my wireless card but what is the firmware? I honestly don't know what it is although it's very basic. I have a Broadcom 43xx as my wireless card (specifically 4306). How do I get the firmware for it? Do I find it in Windows? Also I cannot get b43-fwcutter because I have absolutely to Internet connection on Ubuntu. To post this, I'm using Windows.
View 4 Replies
View Related
Dec 13, 2010
I have recently upgraded my netbook from 10.04 LTS desktop to 10.10 netbook as I really like the new unity feature.Anyway, I have a couple of prism shortcuts that I use for both my personal and work webmail (both are google apps). When I open them I select them to stay in launcher so they are always accessible. Problem is - as soon as I reboot my machine the prism shortcuts disappear from the Unity launcher. All my other shortcuts like chrome, file browser, open office etc all stay...it's just the prism shortcuts.Has anyone else found the same problem? I have searched the forums and can't find anything.PS Just in case any of you don't know, prism is a tool that lets you create a shortcut to any webpage, with a custom icon and a cut-down version of your browser (i.e. no tool bars cluttering the page) so the shortcut almost works like it's own application.
View 1 Replies
View Related
Dec 20, 2010
I am a linux newbie, I spent more than 3 days trying to set up the drivers for my Intersil Prism 2 Wi-Fi adapter on CentOS 5.5. While trying to Make the driver source I receive errors of missing libraries. Is the hostap driver included in the Centos Kernel? I tried with insmod hostap but it didn't work..? Is there a kernel patch with the hostap drivers? I will be glad if someone can give me ideas or directions for setting up the driver properly.
View 1 Replies
View Related
Aug 23, 2010
I am anticipating that someone could give more further information about that, not only simple explanations. How to understand User Time, sys time, wait time, idle time of CPU
View 1 Replies
View Related
Jan 1, 2010
I am having, just installed a fresh 9.10. The only thing I did was an update and installed the wireless drivers. Well i went to to download my favorite browser Opera and firefox just times out. I can get to other websites just fine so far. Though it looks like Office Depot won't let me in either. If I boot into Windows I can connect to either site just fine.
View 2 Replies
View Related
Jul 16, 2010
I am running 10.04 on a Lenovo 3000 N500(?). If I leave a large download/torrent running overnight I come down in the morning to find the connect has broken and cannot reconnect.
View 3 Replies
View Related
Aug 28, 2010
Have had issues with my 10.4 Server regularly. I believe it's something that I've done wrong in some of the hosts settings or the like. When I try and login to the server, especially on startup, I get messages saying the login attempt timed out after 60 seconds and when I login via ssh it boots me from the connection after about 60 seconds of trying to login. It's after entering the password so it's something to do with authentication most likely. I think the issue is with my /etc/hosts file as I said before. Hostname is blackbox and it's only meant to be a local network server.
/etc/hosts file:
Code:
127.0.0.1 localhost.localdomain localhost
192.168.1.5 blackbox.localdomain blackbox
# The following lines are desirable for IPv6 capable hosts
[code]....
View 9 Replies
View Related
Jul 26, 2010
I am very new to linux and I am running into an issue..I've gotten soem new HP blade servers and they cam installed with RHEL 5.3 I need to update them to RHEL 5.4 I register them with my rhn subscription, then once I see my systems online, i run yum update from the command line.
It seems to find a ton of updates and takes a long while to DL everything.Do I have to tell it to install the downloads? I don't think I do...I get some errors about timing out for the last few updates.theni reboot, but when i check redhat-release it still says 5.3
View 7 Replies
View Related
May 19, 2011
A few weeks ago I upgraded one of my laptop from Fedora 13 to Fedora 14 (using pre-upgrade). The upgrade went smoothly and no errors appeared. However ever since the upgrade ssh is not working anymore. I've tried various servers inside and outside the local network. I can't contact any of them. In all cases I get:
Code:
ssh: connect to host aaa.bbb.ccc port 22: Connection timed out
I've tried to get more info using the -vvv option form ssh, but it doesn't mean too much to me:
Code:
OpenSSH_5.5p1, OpenSSL 1.0.0d-fips 8 Feb 2011
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug2: ssh_connect: needpriv 0
debug1: Connecting to aaa.bbb.ccc [xxx.xxx.xxx.xxx] port 22.
debug1: connect to address xxx.xxx.xxx.xxx port 22: Connection timed out
ssh: connect to host aaa.bbb.ccc port 22: Connection timed out
Actions so far:
- checked internet connection. No problem there. Another laptop is working fine using the same connection and the same ethernet cable. That laptop is still using Fedora 13, since I didn't want to get stuck without ssh completely.
- checked "messages" log. No messages at the time of ssh connect attempt.
- checked "secure" log. No messages at the time of ssh connect attempt.
- checked the firewall settings. The settings are exactly the same as before the upgrade (when ssh was still working). Moreover, the settings are the same as the other laptop that is working.
- temporarily switched off the firewall. No difference.
- temporarily switched off selinux. No difference.
So it doesn't seem to be a firewall or selinux problem. And I know the connection is working, so it does not seem to be a routing problem either. What am I missing here?
System specs:
- Asus EEE PC (1 GB RAM, intel atom processor);
- Fully up-to-date Fedora 14 (kernel 2.6.35.13-91.fc14.i686)
View 7 Replies
View Related
Mar 11, 2010
I just installed my first ever install of Linux (used Fedora) and am using SSH to access it from my Windows machine. It keeps timing out. Is there something I need to set to make it available all the time?
I was able to get the SSH on and to autostart just fine but when I boot up it only works half of the time. I have to move the mouse and keyboard on the Linux machine before it will respond.
Also if I am working on my Windows machine and don't move the mouse or keyboard every now and then it doesn't work.
View 6 Replies
View Related
Aug 16, 2009
Running a LAMP server, CentOS as the OS.The sites always been slow, but now that ive optimized it with mysql cache, gzip compression and some other things, its really fast.Except when pages loading seem to randomly 'time out'. The browser sits on 'waiting for x.com'. Closing the browser and/or the tab and opening a new one fixes it, but then it'll happen again eventually. Clicking further links while its 'waiting for x.com' does nothing, basically the site becomes unusable until you close the tab and reopen it.
This happens on all 3 virtual servers we're running within apache. Mainly noticable on the PHPbb forums, probably because they are visited the most.It's not a slow mysql query, i turned on slow query logging over 2 seconds, and the only two hits i got on that i know are unrelated.Ive turned off some optimizations thinking they might be it, but no dice.
View 2 Replies
View Related
Jun 12, 2010
On formula1.com live timing which is java applet starts but does not refresh. Time of training is not counting and there are no new sector times and overall times for drivers laps. Firefox is 3.6.3 and jre is jre-1.6.0_20-fcs.i586.
View 3 Replies
View Related
Apr 19, 2010
I'm looking for a way to time how long a program runs in the terminal. I didn't have any luck searching around but I'm sure it's possible. Does anyone know of the easiest way to do this?
View 2 Replies
View Related
Aug 8, 2010
I am facing problem with firefox and opera. Even google page request ends up in time out error. But google chrome works absolutely fine.
I use 10.04
View 1 Replies
View Related
May 8, 2011
I ran the Kvpnc wizard and imported my config file and when I try to connect it always says connection timed out.I can connect to OpenVPN without a problem using the terminal, all I can say is kvpnc is a real pain and I don't get why I can't connect with it if I can connect without a problem from the terminal.I thought this was suppose to be a simple GUI that you just imported your config add in your cert and the cert path and that's all.
View 1 Replies
View Related
Nov 27, 2010
Incredibly slow this morning, timing out at most sites. Other symptoms on other days - constantly asking for my wireless key, losing connection completely from time to time. This thread relates to a different machine to that in my other recent thread**** Running 10.10 2.6.35-22-generic
View 5 Replies
View Related
Jan 12, 2011
I need to write a script that executes a wget. The difficulty being, if wget just sits there with no reply for a very long time, I don't want the script to run that long.
How can I time out the wget command in the script if it doesn't give me a reply in a minute or so?
View 3 Replies
View Related
Jun 4, 2010
I've just recently started using Fedora again and have a question about BOINC.I see that Fedora 13 is using 6.10.45, but the latest recommended release is 6.10.56.What is the timing on updated RPMs for new BOINC versions? Or is there a guide to updating manually, which I've been unable to locate?
View 4 Replies
View Related
May 20, 2010
I'm having problems flash video on port 1935 is timing out, other flash video works fine though. I'm running 10.04 and have tried flash from the repos (flashplugin-nonfree) and also downloaded the .deb package form the adobe web site, neither work.
I have been using this to try and problem solve but it just says i'm timing out [URL]...
View 2 Replies
View Related
Oct 6, 2010
I'm experiencing an occasional frustration using Evolution with my work email which is on an MS Exchange 2003 server.Everything usually works well enough, but from time to time I'll try to retrieve a message,Is there a setting I've missed in Evolution that might take care of this, or some other workaround?Let me re-emphasize that the server is a 2003 Exchange server (and a source of endless frustration for a non-windows user). It's not a 2007 or 2010 Exchange server, which is what most companies use these days.
View 2 Replies
View Related
Jul 17, 2011
I have a complex network. ADSL broadband comes into the house and connects to an Orange Livebox. An Ethernet cable then connects the Livebox to a more powerful router, a DrayTek Vigor 2710Vn. The reason for this is that the Livebox has a second line capability using Voip, but it is not powerful enough to get around my stone house. The DrayTek router has Voip capability, but as yet Orange will not connect the Voip line to it. I connect to this system with Ubuntu. Android, Windows and I-phone. I can connect to either of the routers, though I usually use the DrayTek.
Voip on the Livebox does not require a computer to run it, you just plug a normal phone into it and use it to get free calls. I actually take this line into a Panasonic telephone switch to give me a 2 line system around the house. The problem with this set-up is that after a short time something happens to the network which prevents Ubuntu computers connecting to it. Windows machines, I-phones and Android phones connect, but Ubuntu does not. If I re-boot the Livebox, or in an extreme case take it back to it's factory settings, the Ubuntu machines can connect again, but it's only temporary.
The fact that fixing Livebox sorts the problem definitely points to Ubuntu being innocent, but at the moment I can't do without the Livebox. That means, for the moment, having to stay with Windows. If I post the output log after a failed connection attempt, all it would show is the connection timing out. Why is Ubuntu so sensitive to network problems that are not of it's making. Is there anything I can do about it other than changing my ISP. I am considering that, but other factors make that difficult.
View 9 Replies
View Related
Jul 18, 2015
I have the following hardware setup:
a NAS running Debian that frequently (but not always) has two removable media attached,a Debian desktop that mounts the above NAS via sshfs,the aforementioned removable media are symlinked to the directory on tha NAS that is then mounted by the desktop.
What I'd like this setup to do is to immediately time out if mounts as unavailable. Instead, I only get the expected behaviour if the NAS is down (the ssh client takes about 3 seconds to do that); if it's up, the removable media automounts (they are symlinked to the directory shared with the desktop) seem to never time out, ever. This happens locally on the NAS as well, when ssh'ing to the NAS and trying to run `ls /media/Storage` or `ls /media/Backup`, these commands never return. It's as if systemd was ignoring the x-systemd.device-timeout setting on the NAS.
The relevant part of the NAS's fstab:
Code: Select all/dev/sdb1 /media/Backup ext4 defaults,noauto,x-systemd.automount,x-systemd.device-timeout=1s,rw,user,nofail,x-systemd.idle-timeout=30s 0 1
/dev/sdc1 /media/Storage ext4 defaults,noauto,x-systemd.automount,x-systemd.device-timeout=1s,rw,exec,nofail,x-systemd.idle-timeout=5min 0 1
[Code] ....
I find it highly interesting that despite both removable media being detached, only one is flagged as having a dependency failed. Both paths exhibit the hang behaviour, though.
What can I do to actually time out when the media are not there?
View 4 Replies
View Related
Apr 8, 2011
I have a remote desktop session to a Windows 7 Workstation that keeps timingut/disconnecting after a minute or two of idiling. Also, sometimes it disconnects while I am in the middle of using it.I have tried turing off all NIC power saving options, the sound option for remote desktop, and all the go to sleep power saving options. I don't have any issues with remote desktop connecting to various Windows Server 2008 R2 Machines and VMs.
View 1 Replies
View Related
