I have a DELL T3500 64 bit and I am unable to install the following Matrox driver: M9140 LP PCIe x16 in RedHat ENT Linux 5.1 .Presently I have a nviDia driver that I would like to uninstall from the workstation so that I could install the Matrox driver.
View 2 RepliesI recently upgraded to 10.10 from 10.04 on my x86_64 system. The upgrade went fine except it cannot load the driver for my Matrox M9148. ("m9x")I simply get a "Cannot load driver" error. (there is more to it, will paste when I finish work)Basically the driver is there and in place, it loads it but cannot use it.When I go to reinstall the driver again manually, it dies with an error only supports Xorg up to 7.5So, now I see this is an Xorg and driver compat issue.I have reported it to Matrox and am awaiting a reply.
In the mean time though, since I need my machine working, is there anyway around the issue, or could I even roll back xorg to whatever it was in 10.04 to get the drivers working again?
I have a Intel server board machine that has a on board Matrox cardWith 11.2 the install barfs to text mode configuring the card during install butonce you log in a root and run sax2 it is OK once the machine restartsWith 11.3 it installs ( apparently ) perfectly then just goes to a blackscreen .. the usb keyboard is dead and that is that
View 3 Replies View RelatedI have fairly new requirement for a second monitor. My main display is running fine using nvidia proprietary drivers.I do have a pcie (probably x16) video card sitting around, but my motherboard only has 1 x16 slot (used by my main display), 2 x1 slots and a few pci slots. From memory, the second video card is an ATI card.Questions:
1. Can I put a PCIE x16 card in a PCIE x1 slot?
2. Would using 1 Nvidia card and 1 ATI cause trouble?
I have a XScale PCIe RS-232 board running in a home built quad core w/ 8GB ram that I want to use to either communicate with a UPS or a RS-232 embedded device. The relevant sections of the output of dmasg are;
dmesg |grep ttyS
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[code]...
I recently added a new graphics card to my machine. Normally, Centos 5.3 runs without a hitch, but since the new card, boots as far as a kernel panic. Even a rescue or an install disk comes up with a kernel panic.I have tried Centos and Fedora CDs/DVDs.The card is a PCIE Radeon HD 4350.It works fine with XP, btw.Ubuntu and OpenSuse will load from install sources.
View 7 Replies View RelatedI have installated and configured Bind. But when I restart the named service, I am getting the following error.
31 14:29:16 Server avahi-daemon[2440]: Server startup complete. Host name is Server.local. Local service cookie is 1560939195.
Mar 31 14:29:46 Server named: /etc/named.conf:3: change directory to '/var/lib/named' failed: file not found
Mar 31 14:29:46 Server named:
Mar 31 14:29:46 Server named: /etc/named.conf:3: parsing failed
Mar 31 14:42:34 Server named: /etc/named.conf:3: change directory to '/var/lib/named' failed: file not found
Mar 31 14:42:34 Server named:
Mar 31 14:42:34 Server named: /etc/named.conf:3: parsing failed .....
I have configured forward and reverse zone.
I'm using xp with one primary partition(C) for xp os,three logical drives(All NTFS).Now i want dual boot with red hat linux.When i inserted the dvd and booted from dvd,it is not going further from starting menu page(press F1-help,....F5-rescue mode).When i installed in vmware it was installed properly.But here why it was not running.I can't buy another hard drive for linux,i have to use the existing disk for both xp and linux....
View 3 Replies View RelatedI am trying to install a PCIe card for data compression in Linux ubuntu 9.10(karmic Koala). As you can see in the following code although I have the root access I can not get permission to install the device driver.As I have the root access I suppose to get access to install the driver. I checked around and got the procedure from a web siteEnabling root access in unbuntuBasically in almost all linux machines we will be havingroot access for login.but in ubuntu by default that option was not enabled.If u want to have root login in ubuntu then u have to do some changes in ur Ubuntu machinesSteps to follow1.First enter into ubuntu as your user login.2.Then open the terminal and type the command sudo -s,it will ask for root access and type the password.3.Then type passwd root it will ask for new password4.Open terminal and go to the path /etc/gdm/5.Open gdm.conf6.search for AllowRoot=false7.and then change AllowRoot=true8.now restart ur machine9.now u can enjoy with root accessThe funny part is when I search for the file which is gdm.conf in the prescribed location, I can not find it.
Code:
root@faisal-desktop:/home/faisal/Desktop# cd AHA/
root@faisal-desktop:/home/faisal/Desktop/AHA# ls
[code]....
i am going to buy a netgear wpn311 internal wireless networking card for my desktop i believe it has an atheros chipset.
can i install the wireless card in my desktop's pcie x16 slot?
I recently finished a mini-itx machine and everything was working great with a fresh Jessie install. I put in a PCIe wifi card and now the computer won't boot. The power LED is on, the PSU fan is spinning, but I get no display output at all and I don't know how far into the boot process the thing even got. I removed the card and the machine boots fine again.
I only have one PCIe slot so it is my only option, I don't have another PCIe card to try, nor do I have another machine to test the wifi card in. The card is brand new, for what it's worth.
WiFi card: [URL] ....
motherboard: [URL] .....
I have 3 monitors and am trying to get the Matrox TripleHead2Go Digital signal splitter with my Linux workstation. When I connect them all I get are blinking green lights on the monitors which I think means no signal. Do I need to download a Linux driver? I've searched online but can't find anything. Maybe the problem is something else. Same happens when trying to connect to my PC.
View 1 Replies View RelatedI have being googling and trying to find out solution to unable to startx.Please note i have already search from last 2-3 days for the solution but didn't found anything.So request someone to guide me step by step.Also one more thing, the server was crashed and i upgraded the existing server using CD. But since then we are not able to start startXI hope i can get some help here ,i am a newbie to linux but i am computer engg so i can understand some logics..I am getting below error
Code:
[root@astarcftp /]# startx
xauth: creating new authority file /root/.serverauth.13592
[code]....
I am trying to create a 2nd node from last couple of days but no luck.do this.I have gone through these article again and again:Here is my setup
node1 ( ricci + luci) : which is working fine
node2 (ricci only) : this is giving me problem
node1
[code]...
I;m using RHEL5, i have a problem with my wireless lan card, my laptop wireless cant be enable , i always show a inactive in the network configuration property, i know it detect in my box code...
View 10 Replies View RelatedI have a redhat 4 on a Hp Proliant server. I did a restart of the server. Now it is not getting to the grub menu. It shows:
Attempting boot from hard drive (C
GRUB GRUB
and it hang there.
I know it has something to do with some controller stuff and I could not figure it out. It used to be working till I reboot.
We have a Oracle 11.2 database running on Red Hat 5.5. The database have a scheduled job to fetch some files from another server using ftp, and herein lies the problem.he job runs a pl/sql that runs the function in an (by us compiled) external libraryThe ftp-functionality itself is done by using libncftp and it's API's.The process starts correctly, but then trying to login to the actual ftp host, ncftp only reports "Unknown username/password" (which is not the case).I have the exact same code in an executable and when run from an interactive shell, it works fine.So the only thing I can come up with, is there are differences when the process is started by Oracle, rather then being ordinary" process.And I am stuck.If there are any environment variables, paths etc missing when running the extproc-process, how do I find out which?Because the real problem is NOT wrong user or password.
View 8 Replies View RelatedI want to create redhat cluster on(vmware) OS Redhat Enterprise Server 5.5
Install Luci on node1
Install ricci on node2
Install ricci on node3
All the computer name records in all system host file. When I try to create new cluster( luci_install init) then showing error...
Status messages:
* Host stationx.example.com is already authenticated
* Host stationy.example.com is already authenticated
[dismiss]
The following errors occurred:
* Unable to create the cluster Luci database objects
***No any cluster.conf file created on any node
I have reinstall the node, but getting same error.
I had Windows XP working. I then put in a new hard disk and installed Redhat 5 on it. rom then i could only boot into Redhat. Further, everyting is very slow. Anothe rproblem is that Redhat does not see my netwrok so I cannot get onto the Internet. I need to have the choice of booting into XP or Redhat.
View 2 Replies View RelatedI bought a Laptop with Sis 771/671 onboard graphic, with a 1440x900 resolution. Since this SIS is not supported by the open suse distribution, I am running it with poor resolution for two years now. Every update of OpenSuse I hope it could be supported now, since I see in the internet that there seem to be solutions for other distributions. However nothing happend yet.
Is there any intension at OpenSuse to do something about it ?
I cant mount a directory on red hat 5 from red hat 4 using fstab.I keep getting permission denied.I mount directories on the same red hat 5 sys from other red hat 5 and 2 old HPUX systems using fstab.When I try to telnet to it i get "no route to host."
View 3 Replies View RelatedI spent all day yesterday trying to figure out why the PCIe expansion (bridge) card I bought was not being detected by my BIOS (and ultimately my RHEL5.4 OS). It was not until I actually plugged something into the expansion card that the bridge itself and the expanded PCIe component were detected.
I have tested and re-tested this issue.My question is this: Why must I have a PCIe component connected to the bridge for the BIOS (and OS) to detect the bridge itself (and the connected PCI component) ?
I've searched everywhere I could think of and have been on google for about 4 hours today searching with no luck.Is there anyone out there who can confirm a working PCIe sound card on RHEL4.4 (Linux kernel 2.6.9-42)?The only cards I've found that work on Linux are the Asus Xonar cards and the PCIe version of the Sound Blaster Titanium but they are confirmed for later versions of Linux but I can't modify the alsa drivers or update the version of RHEL.
View 3 Replies View RelatedI am testing a PCI card in a 4-slot bus expansion chassis. I bought the chassis from CoolDrives.com, it appears to be identical to the Startech PEX2PCI4 unit, but was quite a bit cheaper... This device shows up on my lspci output:
05:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03)
I think that the following line may also be associated with this device:
06:07.0 PCI bridge: Hint Corp HB6 Universal PCI-PCI bridge (non-transparent mode) (rev 11)
I've installed in the expansion chassis one card, a Linux Media Labs BT484 card. This card works out-of-the-box when installed directly in the system, using the bttv driver. Installed in the expansion chassis, the card still shows up as follows:
07:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
07:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
07:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
[code]....
When the card is installed directly in the motherboard it gets IRQ17 or 18. I suspect that it does not really want IRQ0, but that there is some problem detecting the proper IRQ over the bus expander. One possible approach I am considering is to build a custom version of the driver where I can set the IRQ manually to something else just to get the driver to finish loading, then see what happens when I run the card. This would at least tell me which IRQ the hardware is really using and whether or not the 0 reported is correct or not.
I have ubuntu 10.04 LTS. Kernal version 2.6.32.duplicator@Duplicator:~$ uname -aLinux Duplicator 2.6.32-24-generic #39-Ubuntu SMP Wed Jul 28 05:14:15 UTC 2010 x86_64 GNU/Linux.I am trying to install 4port USB PCIe card. But card is not detecting. but card manufacturer says it is plug and play device. this card is working in fedora 11. but i need to install in ubuntu 10.04.
View 2 Replies View RelatedHow to install vim on Redhat 5.
View 5 Replies View Relatedwhat are necessary requirements to install ns2.can i install ns2 in redhat5v
View 1 Replies View Relatedive done this on ubuntu many times but i need to do it on redhat now. This is what i am getting. I cant do the make file thing because of ./configure errors.
[Code],,,,
I have Slack 13.1 64 bits. I compiled my Kernel 2.6.34.1 The Kernel has start normally but I found this message:
[Code]....
Recently I Installed New Redhat server while I Install Any Packages It says:
"No such file or directory"
But If I Search the file using [rpm -qa | grep packages_name]
It shows the package , Also If I Use [rpm -qi package_name] It show package Information , Size and Every thing.
Finally when I going install package using [ rpm -ivh package_name] It says
"No such file or directory"
Screen Shot of error link => [IMG]img135.imageshack.us/img135/2430/linuxerror.jpg[/IMG]