I have had Kubuntu installed for quite some time, I very rarely use it because of my dependanacy on windows but frequently boot up Kubuntu to do updates.A few days ago, I tried to boot Kubuntu and it comes up in command line only, I login but it stays at the command line, no KDE.On the boot list I have Ubuntu 2.6.32-21-generic.I have gotten used to using KDE and now I need to use Linux but am not command line fluent.
View 10 RepliesI had a triple OS xp 7 and Linux Open SUSE 11.4 the last one was the active partition.the grup boot loader used to provide a OS selection screen .any way , I cant boot my system after restoring a full disk image created by "Acronis TrueImage program" , what happens is that i get a BIOS message "there is no operating system insert disk and try again"however when i set winxp partation as active i can boot winxp againThere is some thing I'd like to ask for please ,when i install Linux : did it install grup boot loader on the master boot record or on the boot sector of the / partition ?
View 4 Replies View Relatedbest/simplest way to back up my triple-boot machine, which has Karmic 32-bit, Karmic 64-bit and Windows 7 (64-bit) installed on 3 equal slices of the internal 1TB disk. There are a total of 6 partitions (1 primary+1 logical partition each for the two Karmic, and 2 primary partitions for Win7), and I would like to back it up on an external disk such that the whole system can be restored as-is by writing over the disk. I guess this means correctly backing up data+partition table+MBR, and I would also prefer backing up only the used portion of the disk (rather than creating a 1TB mostly empty image file).
To my knowledge the only way to reliably do this is with "dd" command, but I have never used it ("fsarchiver" seems to be the next best option, but it cannot back up MBR yet; and "partimage" does not have ext4 support). As described here and here, I should run the following commands from a live boot:
1) To back up entire data in compressed format (using 1MB read block to speed up the process):
dd if=/dev/sda bs=1MB | gzip > /backup/image.gz
2) To back up MBR+partition table (stored within the first 512 bytes of the disk):
dd if=/dev/sda bs=512 count=1 of=/backup/image.mbr
3) To restore data:
gzip -dc /backup/image.gz | dd of=/dev/sda
4) To restore MBR+partition table:
dd if=/backup/image.mbr of=/dev/sda
I wanted to know if there is variant of RollbackRX (www.rollbackrx.com.au) freeware or payable. RollbackRX used to Backup/Restore whole system changes in less than 1 minute before OS boot. And it does not consume a lot of free space.
View 9 Replies View RelatedThis question has been raised several times I am sure but...
I would like to create a FULL recovery CD/DVD of my system with a boot restore...
Any recommended for Ubuntu 10LTE Server.
My Mini13 came with hardy preloaded, and it's got pretty messed up since, so I'd like to restore factory OS via a grub entry that looks like this:
title System Restore
root (hd0,2)
chainloader +1
boot
This points to a partition which, when mounted, has this stuff in it:
bootfs.img initrd0.img install.sh logo.png syslinux.cfg vmlinuz
boot.msg install.cfg ldlinux.sys rootfs.img vesamenu.c32
I'm not a computer, but that looks pretty good to me but when I select this grub option it just says:
Boot Error
Is there a log or something that might give me more info about the error?
are there any sweeper / cleaner apps which can take back my installation as to when it was new. I know home directory could have config files etc..but that doesnt matter, i want all packages and applications reset to how it was when i had a clean install. I am using Natty
View 2 Replies View Relatedwhat could this bei saved my correct iptables file @ Code: /etc/iptables.up.ruleswhere webmin is looking for it.webmin config is to automaticly boot this file and addes a line at.
Code:
/etc/network/interfaces
file
[code]...
O/S: Fedora 12
I am newbie in linux. What I want to do is: Make backup for my file system, cos I learn how to configure servers. So if I made some thing wrong, I want to be able to restore the default setting for my files. Instated of install new O/S.
My manager at work asked me to setup an FTP server running LINUX. i had a post about some custom scripts and commands that i needed, so after i configured and set everything up, i got another assignment....here we go, i need to come up with a way of backing up the entire system, or creating a script that will setup,install and configure the FTP related features i have made working there.i am wondering what would be the most ideal/best and easy to do way to back up the system? the goal is : in case if HDD fails,r anything goes wrong.system can be restored in no time. this is still up in air thing, i offered taking some time on a weekend and setting up same system on say,ew drive, and swapping them when one goes bad... but what would be an alternatives
View 2 Replies View RelatedI did something weird and now my text size is like 3pt on every system window, but when I go in and change my window fonts to larger to something that looks normal, it makes my clock, bash, and other fonts absolutely gigantic. Is there any way I can just roll back my system and it's settings? It wouldn't be much bother as I installed the OS yesterday. I'd hate to have to reinstall entirely though
View 1 Replies View RelatedI bought a used Acer Aspire one with Linux on it and it works great. I want to restore it to factory settings but I do not have a restore disk. (not to mention that the unit doesn't have a CD drive anyways.)
I have read on other sites that Alt-F10 works but I think that is only for WIN because I can not get that to work. Is there an equivalent function with Linux.
There were some files residing on my ext3 file system, using Ubuntu as my linux distribution. Yesterday I formatted the hard drive using a windows install CD, rewriting it with a new NTFS partition. I'm willing to restore my personal files deleted due to this format.
View 3 Replies View RelatedI am running RHEL 5 on Vmware Workstation. That is i inslled Vmware Workstation on windows 7 and then in Vmware i installed RHEL 5 as a virtal machine. By mistake i made some wrong entry in my /etc/fstab file that is i was trying to automatically mount one folder under another folder. My syntax was wrong. So when i restart my RHEL 5 , at the boot time due to wrong entry in /etc/fstab system is giving file system error as follows:
Checking filesystems
fsck.ext3: Unable to resolve 'LABEL=/home/download'
fsck.ext3: Unable to resolve 'LABEL=/var/ftp/uploads'
[FAILED]
[code]....
Image Hard drive Ubuntu Operating system 9.10 Complete back up and restore. Changing over Hard Drives need a complete back up not just save files. So the image can be restored on any hard drive that restores the computer to its original state before it was imaged.
View 14 Replies View RelatedI just made my system unbootable... Here is what i did.. I have two sata HDDs
160 GB (Contained Windows 7)
500 GB
I copied entire 160 gb as an mirrored image to 500GB HDD using Acronis Disk Director. I deleted entire 160 GB HDD.. Removed the 500 GB HDD and kept it seperate.. Installed ClearOS Enterprise 5.2 Worked a little bit... The i wanted to delete ClearOS.. So i connected 500GB HDD and booted again in Acronis Disk director Formated the entire 160GB HDD.. Copied back the entire 160 from 500GB HDD.. Now my sytem refuses to boot... Just 4 letters "GRUB" appears on the screen... I tried booting using XP CD.. It gives a blue screen.. I tried Windows 7 CD.. It says unable to fix due to MBR problem..
After completing the installation of Fedora-FEL edition, I cant boot from my hard disk. "No bootable device found " error appears.
I have one Windows XP & 2 Linux installation in my disk.
I tried to restore grub using "setup (...)" command.but same error repeats.
Even I cant restore Windows XP using "fxmbr" command in... recovery console .
But I can boot from that drive by "chainloader" command in grub. code...
Running above command in grub terminal boots my hard disk ("hd1" is my "unbootable disk")
I just recently installed ubuntu 9.10 in my upstairs computer. It is a single boot system.Downstairs I have a dual boot system. I have windows vista and ubuntu 9.10 installed. It worked fine. I wanted to make this a single boot system and uninstall ubuntu 9.10. I cannot get rid of the grub bootloade
View 14 Replies View RelatedI am trying to restore my system to Ubuntu 10.10, using a system backup made with REMASTERSYS. When I reboot, I get the message: GRUB error:15 I found many threads discussing this issue, most notably here: [URL]
[Code]....
Im finally deleting vista from my disk, but as I am game addict I will re-install it afterwards just for games. Now I assume that will overwrite GRUB, so how do I restore boot record and at same time keep my grub config?
View 5 Replies View RelatedRecently I've backupped my entire /home folder on my laptop with grsynch trough ssh.Since I already had a simply text file containing all installed programs, I figured 'then, when i go from the backup trough my desktop, all my program settings will be restored if i run the txt file to install all those programs first.So i installed al programs, then i went from backup to /home on desktop, logged out and back in. Started up a random program (tried thunderbird and filezilla) and no settings were to be found.In retrospect, docky did start, but didnt have all the launchers i had on my laptop. so that could have been a clue.
View 4 Replies View RelatedSo 2 days ago everything was all fine on my machine. Has been for about a month, but all of a sudden as of yesterday I have no sound, I am seeing IRQ interupts on boot, During boot I am seeing file system is not clean, , and swap space is being used for the first time while doing normal task, etc. These are 2 new hard drives in RAID 1 with ReiserFS. I should have used a newer FS but thats a whole other argument.
Anyways here we go.
The system is Debian Lenny amd64
Physical RAM 4GB + 6GB swap
/var/log/messages
Code:
Feb 21 07:35:09 Sarah kernel: imklog 3.18.6, log source = /proc/kmsg started.
Feb 21 07:35:09 Sarah rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="3994" x-info="http://www.rsyslog.com"] restart
code....
I am new to openSUSE (and to Linux). I have try Ubuntu, Debian, Fedora and ended with openSUSE that seems to be the one I like. But I have some problem now. The system seems to hang on boot and after searching the Internet I found thread about ATI display driver (and I have ATI) so I installed ATI drivers. The system got worse and playing videos start to be not as it should be (and often freezing). I decided to uninstall these drivers to get my system back as it was but ended with more problem. Now my system don't start. I can boot in some kind of command prompt but nothing else.
Can I do something to restore the system or will I have to reinstall the system? I don't know if I want to reinstall it. I am using a very slow Internet-connection (air-card) and I have had so much headache on the other Linux (before I did end on openSuSE). I like openSuSE (even there is some minor things, like I cannot change my default browser to Opera, a Browser I have been using for almost 10 years but I still can use the Opera so it is a minor thing).
First off, Ubuntu 10.4 is working great on my new laptop and I really enjoy it. And it is super fast. My question is now that I have everything all set up, all my packages, my windows settings, and my ATI driver, my updates, etc., I want to be able to keep it all. Maybe somebody could point me in the right direction or give me some better terminology. Would love to learn more about distros in the future. For now I just don't want to have to do all this updating again. There are a few things I have found like Clonezilla and others, but they seem to be a bit advanced and more for servers.
View 9 Replies View RelatedA friend has a netbook running a dual boot setup with Ubuntu (9.10, I think) and Windows XP. She recently decided to run system restore on the Windows partition and can't boot into Windows anymore. I told her I would help her fix it tonight, but before she gets here I figured it would probably be helpful to ask if this is a well known issue and if anyone has any suggestions on the best method of fixing it.
I planned on first making sure the grub is targeting the Windows partition correctly, but I suspect the problem could be that the system restore point she used was one from before she had a linux partition. If that is the case does anyone know if this could potentially destroy the windows installation?
I was installing mail server on a desktop for just experimentation using sudo tasksel command. I selected the second option that says mail sending using internet. During installation it asked for something about phpmyadmin, which was already installed on my system. I selected no, and then during installation it removed all the utilities from my system and now system startups in terminal mode. I have some very important data on that system that i can't afford to lost. please help me out so that i can again start the system in normal graphical mode or tell me a way so that i can transfer my data to anyother media.
View 6 Replies View RelatedI restored my laptop to an image created the 1st time I used the laptop. Since restoring the system won't load. After the initial boot screen and check to boot from cd it just resets. It never makes GRUB menu were I can choose the OS I want. I'm dual booting Vista and ubuntu but can't get into either.
View 9 Replies View RelatedIs it possible to get a system restore point on ubuntu?
View 2 Replies View RelatedThe problem is this: I have a 320gb HDD splitted in 4 partitions. When I first installed Windows XP I formatted the HDD in 3 (Windows system partition, Media partition and another one I left for Linux). However Linux requires another partition for swap. Everything was just fine. One day Windows stopped working and I tried re-installing it. After the system was ready to start, Windows failed to boot with "NTLDR is missing" message. I tried to recover the Master boot record, even replaced NTLDR manually - nothing worked. I read that in order a HDD to be partitioned in more than 3 parts the so called "extended" partitions must be created. I think this may cause the problem but I don't want to wipe out everything (I have more than 100 GB of books most of which are not available anymore in the same locations I have downloaded them)
View 1 Replies View RelatedI have accidentally removed my /boot partition(when installing grub using LiveCD i'm typing "rm -rf /boot" instead of "rm -rf boot") After that i have installed grub, have to reinstalled latest kernel(2.6.29.6-217.2.3.fc11.i686) using rpm(and 2nd time using yum) but result the same: i can't boot into my system. Unfortunately, i can't copy&paste log, but booting stopped after something like a:
mounting /proc
mounting /sysfs
Creating /dev
then kernel finds keyboard and mouse and... and nothing. Is it possible to restore my system without reinstalling distro?