General :: Opensuse 11.3 Nvidia Gtx260 Dual Display - Xinorama - Extended Desktop Mouse ?
Jan 14, 2011
Recently installed OpenSuse 11.3 on my system, Setup dual monitors w/ the latest Nvidia driver from Yast repo : download.nvidia.com
Initially twin view ( same desktop viewed on both monitors ) worked no problem
Once xinorama was enabled to extend the one desktop across both I encountered a mouse issue.
Main monitor is on the right, 2ndary on the left... When I drag the mouse from the right monitor over to the lest.. the cursor appears to get stuck on the left monitor's right hand edge.. it flickers as i move it around...
If I drag the mouse to the right a few whole mousepad lengths it will come back to the right...its like fighting to bring it back..
View 1 Replies
ADVERTISEMENT
Jun 9, 2010
opensuse 11.2 ,my monitor keeps going to sleep or somthing and this is a problem when im watching videos,ive set screens power setting but they dont seem to be whats doing it.im running a nvidia gtx260 and have installed nvidia drivers for series 6 and up.dont know if its the divers or somthing else.
View 9 Replies
View Related
May 19, 2010
I just got a new computer and I have been busy setting it up with openSUSE 11.2. I am trying to install the Nvidia proprietary driver for my graphics card, a Geforce GTX 260, but it will not work. I added the Nvidia repository and I am installing the driver for GeforceFX series cards but every time I restart I get a command prompt and if I try to start x it says that my card is not supported. This is really getting frustrating, I need the proprietary driver so I can play DDO with Wine.
View 2 Replies
View Related
Mar 9, 2010
I am trying to set up dual monitors for lenny but nosuccess for the moment.
They were working fine for the same setup on ubuntu.
Using xrandr I get:
I read that virtual screen size could be the maximum part which is of no use in comparison to the current size.
So setting a virtual part in my xorg does not help much. If the above is right.
I have:
How to get the external monitor work in the extened screen mode.
View 2 Replies
View Related
Jan 15, 2011
just setup suse 11.3 , put on the Nvidia 19.29-22.1 drivers via yast , no kms is set in inetd , nomodeset on grub boot line etc... Even tried installing the driver " the hard way " dual monitors come up, setup xinerama to "Extend" my desktop , and the main monitor ( right side ) is good, visually the left monitor (2ndary) is good.. but whenever I move my mouse over to the left screen the mouse pointer dissapears, flickers along the right hand border of that screen... and if i move the cursor back to the original screen i have to really fight to get it back to the main screen....Copy of my xorg.conf , still very basic...
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04.
nvidia.com) Wed Dec 8 12:27:27 PST 2010
[code].....
View 9 Replies
View Related
Apr 23, 2011
My power went out for an extended period of time and now my graphics are messed up. I started my computer up and I only can get 640x480, so I was trying to reinstall the drivers but the nvidia drivers on the repositroy do not make sense as far as what goes with what, or descriptions of them. I downloaded the driver off nvidias website instaled it. It went to my desktop same problem.
View 9 Replies
View Related
Jul 15, 2010
This little program is great for Windows users with multiple displays:[URl]...Anybody know of a similar program or some way to tweak some settings to get the same effect in Linux?
View 2 Replies
View Related
Sep 2, 2010
I am trying to get an extended desktop (laptop monitor + extra) on my OpenSuse 11.3 system (64). I use kde 4.4.
It used to work on my OS 11.0. Here is the deal now:
- I use NVIDIA G2 driver from the OS repositiory
- laptop screen works fine, including compositing, 3D etc
I run nvidia-xconfig to generate an xconfig file. Everything still works fine (even after x reboot):
Code:
Next I login as root and open the run nvidia-setting program. There the second monitor is detected. I enable it as extended desktop and check: enable Xinerama.
I reboot.
Problems:
- compositing is off, I cannot enable it
- if I move my mouse cursor to the second screen, it only stays there for a second and vibrates enormously.
- if I use a window on the 2nd screen. X crashes
Things I can add/remove from the xorg.conf?
Now the xorg.conf is as follows:
Code:
View 2 Replies
View Related
Apr 15, 2011
I'm running Ubuntu 10.10 on a Dell m65 mobile precision laptop w/ nNvidia card.
I booted up my system. Login screen appears. I login. I can hear the login sounds. I can hear my notifications telling me I have email. My mouse works. My keyboard works. But I don't see my desktop. All that's in front of me is the background that I had at login time. I don't see the panels nor the desktop icons. I don't see the interactive grouping/stretchy rectangle thingy when clicking and dragging on the desktop.
I've never experienced this before. I never had a problem w/ this before. I had always been running in hi-res mode.
I did update my system earlier this morning and it wasn't until this afternoon I had to reboot it.
These are the things I've tried, none of which worked.
1) Downgraded my nVidia driver version
2) Changed the xorg.conf to a generic version with basic resolution (I had been running 1900x1200)
3) Tried restarting nautilus. I did this from the command prompt. I just get "Failed to contact configuration server; the most common cause is a missing or misconfigured D-Bus session bus daemon.
4) Tried an older kernel
5) Turned off compiz
These are the things I've tried and they do work
1) Boot to recovery menu. Run in failsafeX mode. I can see my desktop but everything is huge.
2) Run Desktop Edition (Safe Mode). I can see my desktop but everything is huge. I also notice that my desktop icons had been moved around. I think I was doing this when I couldn't see them!!
3) When in Safe Mode, I can configure my nVidia settings to be hi-res. But I can't these settings to stick when booting to normal mode.
View 6 Replies
View Related
Nov 1, 2010
I recently installed a DisplayLink usb adapter on my desktop to use my tv as a second monitor because it had no vga socket, it works great only I can't use the tv as an extended desktop. The 2 monitors work perfectly seperately but I want to be able to use one as the main screen and the other as an extension. I am running Maverick on a P4 2ghz dell optiplex 260 and the output to tv is hd.
View 2 Replies
View Related
Aug 17, 2011
having trouble setting up a dual monitor from my Dell xps laptop using an HDMI port. It dual boots onto Ubuntu 10.04. The computer has a Nvidia GeForce GT 555M with Optimus graphics card I need to make sure I have not installed the restricted drivers. So I think what is happening right now is that the graphics are shown off the integrated graphics card. This is my output from <lspci | grep VGA>
Code:
00:02.0 VGA compatible controller: Intel Corporation Device 0126 (rev 09)
01:00.0 VGA compatible controller: nVidia Corporation Device 0dcd (rev a1)
The forum recommends to use this program called Bumblebee but I have had some issues with that in the past. Is there somehow I can setup my dual display while staying on Ubuntu 10.04 and not installing Bumblebee? I have researched into setting up dual display walkthroughs before but they all concentrate on nvidia or ATI configurations.
View 6 Replies
View Related
Jan 16, 2011
OS Linux Mint 10, Intel graphics, SIS usb2vga adaptor.
I have three screens. The netbook screen with the extended desktop onto a vga screen and a third screen connected to a usb2vga adaptor.
The extended desktop screens without the usb2vga adaptor works perfectly. I can maximise applications to either screen perfectly without them spreading across both screens. As soon as I connect the third screen via the usb2vga adaptor maximising an application causes it to spread across both screens yet the third usb2vga screen has it's own virtual desktop environment.
I have tried numerous versions of my xorg.conf file that I have generated to incorporate the usb2vga adaptor to make this work and regardless of what xrandr commands I send including changes to the gconf settings nothing seems to solve the issue.
It seems odd that I can create a panel and position it left, right, top or bottom of the second monitor of the extended desktop and it sticks to the screen dimensions yet I can't get any application to do the same when there is a third screen connected through the usb2vga adaptor.
I don't use Compiz, it crashes my system and I don't want separate workspaces I want the extended desktop with the two separate virtual screens to fit on the two separate screens that form part of the extended desktop.
With Xinerama deprecated what other options do I have.
View 5 Replies
View Related
Sep 20, 2010
I would like to use the VGA-Port for Beamer in "Mirror" Mode how to modify the xorg.conf? I am not familiar with linux configuration.
View 2 Replies
View Related
Jun 4, 2015
I'm having trouble with Debian 8 and using my dual monitor setup. Whenever I install a desktop that uses lightdm as a display manager (XFCE, MATE, Cinnamon) the login screen is cloning the two monitors rather then extending the desktop. I don't have the issue with gnome 3 (gdm) or kde (kdm). I tried installing Slim as well, but that has the same cloning issue.
I had a similar issue with g the XFCE environment, but I was able to resolve it by installing arandr and configuring the monitor layout. Upgrading from Stable to Testing also fixed the XFCE issue with the newest version of XFCE. Unfortunately I still have the display manager issue (lightdm/slim) in Testing as well. I would prefer to use XFCE but I'm willing to move to Gnome 3/KDE if need be to resolve the issue with the login screen.
View 3 Replies
View Related
Dec 14, 2014
How could xorg be set-up such that different monitors work with different DPI but still compose the same extended display?
I have a 15 inch laptop display extending to the right the main display which is 23 inch. The resolutions are comparable, but the difference in pixel size is very large. Thus, either the external display has too large fonts and UI, or the laptop one has them very small. Moving them at different distances is not entirely possible.
xrandr info:
eDP1 connected primary 1920x1080+2048+0 (normal left inverted right x axis y axis) 344mm x 194mm
VGA1 connected 2048x1152+0+0 (normal left inverted right x axis y axis) 510mm x 287mm
I heard that Windows has a hack (which I can't check) for extending displays with different pixels sizes: it computes in which of the displays a window has most of it's surface and sets the DPI for that window based on that. Thus a window will change DPI when crossing monitors, (and will look too small/large on one of the monitors if it is in the middle).
View 0 Replies
View Related
Jul 18, 2010
My current set up in OS X has an external monitor (Acer H243H) and my MBP 13" screen as an extension. The only way for me to currently get the menus and panes on the external monitor is to turn the Macbook display off. is there any way for me to change this?
View 1 Replies
View Related
Mar 17, 2010
I have extended desktop working on my netbook (finally, by turning off compiz), but now Gnome prefers my netbook's main screen as the main display (with the panel and such) instead of my external monitor.How can I switch this? I don't see any setting for it in the Display dialog.
View 3 Replies
View Related
May 23, 2011
How do I get it to display a different desktop background for each desktop? I'm sure I saw this option somewhere, but I can't find it again.
Secondly, it defaults with 4 desktops in a 2X2 grid layout. I changed it to 2, then back to 4 and now it has 4 desktops in a linear layout (1x4). How can I change it back to 2X2?
View 5 Replies
View Related
Jun 13, 2011
I have openSUSE11.3 KDE with the latest Nvidia binary from the Nvidia repo. I have two monitors configured and working more or less. If I configure for separate displays the secondary display has a X window with an x for a cursor. It doesn't look like that configuration is happy. If I configure for twinview I have one continuous desktop spread across two monitors. I have been using nvidia-settings to configure the displays.
What I want is for the right display to mirror the left display. How can I or can I get it to mirror? Looking in Personal Settings (Configure Desktop) doesn't show any configuration there for mirroring.
View 9 Replies
View Related
Apr 16, 2011
I have XFX ATI-HD5670 and use proprietary catalyst 11.2-1 in 64-bit Fedora 14.
I am not sure when this started, or if it ever did work before, but when I started noticing that the screensaver will not turn off the monitor, I set the gnome power manager to make the monitor sleep after an hour.
Now, the display will not turn back on after it has been in sleep mode. I know the system is still running fine as I can ssh from another PC and see that everything seems to be normal, no error message in dmesg, /var/log/Xorg.0.log, etc.
/var/log/Xorg.0.log shows that monitor DPMS is not detected but still enables DPMS:
Is this a problem with catalyst driver? I know it's not the PC or the monitor, because I have a 2nd PC with the same video driver with the same problem, but others without this driver don't (ati open source, nvidia, etc. all work fine.)
I'm wondering if the problem always existed before, but I just didn't notice it because the display sleep mode was never set? If that's the case, my hunch is that it looked like it worked because the monitor was smart enough to turn itself off when the screensaver kicked in and just showed a blank screen, and the video driver was never involved with sleep mode until I set it in gnome power manager, at which point it started showing this problem of not waking up? And because the screensaver was no longer set to blank the screen, but to show some animation, that's why the monitor will never sleep anymore?
View 2 Replies
View Related
Apr 18, 2010
I have a thinkpad T43 with a dock and a 19" Dell monitor attached. Im trying to get an extended desktop.Using the default display program (using ubuntu 9.10) I can mirror the screens just fine. But, when I click the radio button to enable the extended desktop, the monitors (both of them) go black. Some times it doesn't come out of this. (yes, I'm waiting more than 25 seconds) What can I do to make the extended desktop work? here is my display info from the command lshw:
*-display:0
description: VGA compatible controller
product: Mobile 915GM/GMS/910GML Express Graphics Controller
vendor: Intel Corporation
physical id: 2
[Code]...
View 1 Replies
View Related
Aug 9, 2011
This morning, I authorized an update as almost every day. I saw that the nvidia driver was on the list but in recent years, I no longer fear these driver updates since everything usually works well...
Except that this time, no! I turn on my pc this afternoon and more 3d effects. I run "Nvidia X Server Settings" which tells me I do not use the nvidia driver and must run as root the command "nvidia-xconfig," what I do. I restart X and no display at all, only the prompt in text mode!
View 9 Replies
View Related
Jul 6, 2010
I installed nVidia by 1 click off suse site and on reboot my display is gone. I booted with failsafe Kernel. How do I get my display back with nVidia driver instead of default one.
View 9 Replies
View Related
Jan 28, 2010
When i start the install of the open suse linux 11.2 load the kernel but later my display is in black, i think that is my graphic card becouse in other linux only load linux without graphic mode, what i have to do for install open suse?, i can download a driver with the installer or something like?
View 4 Replies
View Related
Aug 17, 2010
I just purchased a new notebook, namely an HP Pavilion dv6, with a GeForce GT 230M. Also, I have a neat 1920x1200 display with an HDMI connector, which fits nicely with the corresponding outlet on the computer. Now I'd like the external display to be the main display when connected, with the internal display as an expansion to the desktop, and the internal display should, obviously, be primary when on its own.
The reality looks quite different: Not too surprising, with the default drivers I got only a 800x600 resolution, but with the correct drivers installed, I got the full resolution on the integrated display. My external HDMI-display, however, is dead. With the xorg.conf file being obsolete I can't really use the configuration app by nvidia, can I?
View 1 Replies
View Related
May 31, 2010
I am new to opensuse and have installed 11.2 KDE. It is simply perfect for my system. However after the initial setup the display resolution was set perfectly fine for my 18.5" LED monitor, default resolution was 1366x768, and everything looked good from desktop to fonts but the OSS drivers didn't support compositing so I decided to switch to nvidia drivers. I installed the driver as shown in openSUSE repositories page, for my 6600GT card. Now after rebooting everything is stretched,even the fonts look really ugly and fuzzy.
I am unable to find any mode in Nvidia XServer settings that would correct the current ugly stretched display. I am unable to set 1366x768 manually as well, doing so my PC won't boot to KDM but rather sticks to console. Now it's for sure that my monitor and display card supports 1366x768 resolution but it's just that nvidia drivers/Nvidia XServer settings won't let me set that resolution. How can I set the resolution or even better if I can enable compositing using OSS drivers then that would be great an dm willing to switch back.
View 9 Replies
View Related
Jul 20, 2010
I am having a few strange issues with my new SUSE 11.3 install. This is my first time attempting to use it as my full time OS, so I can't say if these problems existed in previous versions.
1.) When I configure extended desktop, it works fine, but the settings do not save. Anytime I reboot my system, I have to reconfigure the Dual Display settings
2.) If I enable openGL effects, or use an OpenGL screen saver my system locks up and I can not restart X. (I have to power cycle the computer)
3.) I get corrupt icons sometimes in my system tray and desktop. (They look like a TV that is tuned into a non broadcasting number)
I have a Quadro 1700, and I read about installing the NVIDIA drivers instead of the ones that come with SUSE.
View 3 Replies
View Related
Mar 9, 2010
I installed the nvidia proprietary drivers with click-install and everything perfect, I have desktop effects working but the problem is that when you open the config. screen settings to make sure everything was really good, I get to screen unknown April.
The maximum resolution is the correct 1440 * 900 for 19 "but the refresh rate by not recognizing the monitor down to 50hz me and gives me the option to 60hz as it was before installing the nvidia drivers.
How can I fix the display settings?
View 6 Replies
View Related
Mar 31, 2011
I bought a PC with Window Vista on it as my partner needs it. Using gparted I set up Primary partitions for Vista OS (sda1) and Ubuntu OS (sda2), plus an extended partition for Vista files, Ubuntu /home and swap:
fdisk -l
Device Boot Start End Blocks Id System
/dev/sda1 * 1 3969 31880961 7 HPFS/NTFS
/dev/sda2 3970 5294 10643062+ 83 Linux
[code]...
My problem is Vista (as always). The 30GB I allocated is not enough, even just for the OS and it won't now boot from GRUB, though I can see it from GRUB. I don't want to do anything that risks a problem for Ubuntu. Will grub still see both OS if I wipe sda1 (Vista OS) and reinstall Vista OS on the extended partition sda6? Ideally I would like to merge sda1 with sda6 and install Vista on that, but that looks way too risky / impossible.
Edit - There is another drive on the PC which is much larger and I use for backup. Is there any scope for installing Vista on that one so that GRUB still identifies both. Not ideal as I like having one as the backup for the other.
View 4 Replies
View Related
Jan 9, 2011
I have a bit of a problem with the proprietary nvidia driver which I installed as a binary on suse 11.3, when I run the nvidia-settings gui it does not give any widescreen display modes as options. My monitor is an Acer x193w which will do 1440x900 but there is no option for that. The monitor is just listed as a generic CRT, and only 4x3 display modes are given. My card is a PNY Geforce 6200 AGP 512MB.
View 9 Replies
View Related
