My problem is i use a command " route add -net to add a route oand gate way, how do i remove the route addid if it is incorrect but also my pc's use a standard static ip 192.168.1.X but my gateway is as a given 196.215.X.X if i add this gatway there is no internet but the same gateway is used on windows pc's
View 4 RepliesI am running 10.04 and am trying to add a route to a remote network using a gateway that is NOT on the local subnet. I am not messing with the default GW as all the other posts I can find are. I am using public IP addresses, but all of this is contained behind a firewall. I need to add a route to a private network (192.168.1.x) that is behind a router attached to a different subnet. The current routing table looks like this:
Code:
Destination Gateway Genmask Flags Metric Ref Use Iface
xxx.xxx.108.48 0.0.0.0 255.255.255.240 U 1 0 0 eth0
0.0.0.0 xxx.xxx.108.49 0.0.0.0 UG 0 0 0 eth0
The remote network is 192.168.1.0/24 and it is reachable via xxx.xxx.37.203. I can ping the gateway no problem. However when I try to add a route to this network I get an error.
route add -net 192.168.1.0 netmask 255.255.255.0 gw xxx.xxx.37.203
SIOCADDRT: No such process
I assume this is because the GW is not on the local subnet. When I try this on a machine that is connected to the xxx.xxx.37 network, everything works fine and I can reach the remote network. I even tried adding a static route to the gateway, but that did not help.
route add -host xxx.xxx.37.203 gw xxx.xxx.108.49
My workstation is on a network, let's say 10.100.0.0/24. I'm opening up an openVPN Tunnel to a test environment in my company, receiving a lot of routes to this network (address range 172.xx.yy.0). Everything is working fine so far. In this test environment I placed a number of virtual systems having their own private network (10.99.0.0/24). I have one machine in this virtual cluster which is able to forward incoming IP traffic to the others.
When I login to this gateway system, using the 172.xx.yy.zz address, I can logon to the others using the 10.99.aa.bb addresses. Fine so far. But I have to be able to call these machines with the 10.99.0.0/24 addresses from my laptop. So I tried to add a route like:
route add -net 10.99.0.0 netmask 255.255.255.0 gw 172.xx.yy.zz
Unfortunately I received an error messages:
SIOCADDRT: No such process
According to the entries in other forum articles (Google helps in most cases), I have to add a host route first:
route add -host 172.xx.yy.zz gw 172.well.defined.dest
Ok I am a complete Noob when it comes to anything other than a windows based unit, so please be patient with me. I am able to connect to the Internet using a wired connection.
View 6 Replies View RelatedFTP is not working through a gateway and I think I found that I need to modprobe ip_masq_ftp. However, when I do try to load ip_masq_ftp I get the error: FATAL: Module ip_masq_ftp.o not found.My question is: how do I get ip_masq_ftp?More questions: Do I have to build a new kernel? If I do need to build a new kernel do I just include the ip_masq_ftp module or are there other modules that I need?
View 1 Replies View RelatedI would like to have a sms gateway that is sending sms without using a cellphone(GMS) on my side.
Is there a pack that can be used this way?
I've got a Gateway CX2724. The sound works perfectly out of the speakers and headphones, but I can't get the internal mic to work for the life of me.
I asked around on other threads and tried a few modifications to /etc/modprobe.d/alsa-base.conf and none of these get the mic working when appended:
From the ALSA-Configuration instructions
Code:
options snd-hda-intel model=ref
Ideas taken from this thread
Code:
options snd-hda-intel probe_mask=1
Code:
options snd-hda-intel model=test enable-msi=1 probe-mask=1
This also doesn't work (modified from this thread.)
Code:
options snd-hda-intel model=ref probe_mask=1 position_fix=1
This also doesn't work (from "Extra Hints to get sound working.")
Code:
options snd-hda-intel model=laptop position_fix=1 enable=yes
When I use alsamixer to turn "mux" all the way up and have my headphones plugged into the microphone jack (don't have an external mic... ) in the front of the computer, I am able to record things but the volume is greatly muted. Perhaps the external jack is set to default for the microphone instead of using the internal mic?
I also have the output for alsa-info.sh if you want it - this was mentioned in the alsa configuration file (/usr/share/doc/alsa-base/driver/ALSA-Configuration.txt). Info about alsa-info.sh here.
I have a network gateway system which runs redhat 7 (2.2.16)
Firewall running is ipchains
Internal network is eth0 192.168.5.1
External network is eth1 99.99.99.98 (example add)
My problem when I change the static address of the external network from 99.99.99.99 to 99.99.99.98 I am not able to connect to internet. From my preliminary investigation ip is not binded to network card., but I am not sure, is there a way to check binding accurately
Below is the ifcfg-eth1 file contents
DEVICE="eth1"
USERCTL=no
ONBOOT="yes"
BOOTPROTO="none"
NETMASK="255.255.255.0"
IPADDR="99.99.99.99"
IPXNETNUM_802_2=""
IPXPRIMARY_802_2="no"
IPXACTIVE_802_2="no"
IPXNETNUM_802_3=""
IPXPRIMARY_802_3="no"
IPXACTIVE_802_3="no"
IPXNETNUM_ETHERII=""
IPXPRIMARY_ETHERII="no"
IPXACTIVE_ETHERII="no"
IPXNETNUM_SNAP=""
IPXPRIMARY_SNAP="no"
IPXACTIVE_SNAP="no"
I have updated the address change in ipchains firewall scripts. Before IP change network was work fine with this firewall scripts.
I recently moved into my room-mates house and her wireless was not secure as I was able to log on to it unsecured with my Fedora 12 Laptop. After Securing it with WPA all the windows computers had no problem getting back on to the now secure wireless. Using GNOME I went to SYSTEM then PREFERENCES and NETWORK CONNECTIONS and clicked on the wireless tab and configured wireless security tab and configured for WPA WPA2 Personal. No problems. But when I go to the gnome tool bar and click on the network and see our SSID it wants to use WEP 40bit and others methods but has no selection for WPA.
View 10 Replies View RelatedI'm not able to get the Desktop Effects/3D graphics to work on a Gateway laptop. I suspect that I'm not using the correct nvidia drivers but I don't know what drivers I need for my system.I followed the instructions from this link with no luck.
Some system info:
# uname -rs
Linux 2.6.35.10-74.fc14.x86_64
[code]...
I was running 2.6.26 and I've recently upgraded to 2.6.32-trunk-amd64 along with other packages (mostly dependencies)... which possibly involved the network stack.
After this upgrade my home gateway stopped working and I'm clueless to where the problem may be.
I can see that the iptables are still there when I type:
iptables -t filter -L -v -n -x --line-numbers
iptables -t nat -L -v -n -x --line-numbers
My headphone audio jack is not functioning properly. When I plug headphones in, the internal speakers go silent, but no audio is coming from the headphones.
View 1 Replies View Relatedi did install opensuse and everything ok; i did configure it to be the server and gateway for a little office network Everything seems to be ok most of the time but sometimes (usually between 5 and 7 pm each day) internet stops working and there is no way to let it start again. So i turn off the suse, switch all cables to the old fedora server, just turn it on fedora and internet works. Turn off fedora, connect suse, let it start and everythng ok...it happens all the times
View 9 Replies View RelatedSounds drivers not working properly after fresh install of Natty.
View 3 Replies View RelatedI was adding a line in terminal to try to get skype working and i added a line un-necessary and i need to edit the file. How do I either remove the file or edit it. It is a file in etc/yum.repos.d It says that it is read only, and i can't find how to change permissions.
View 2 Replies View Relatedi'm just trying to get the sound working on my laptop I found a solution online 'Sound: add options snd-hda-intel model=dell-m6 to /etc/modprobe.d/alsa-base.conf.
View 1 Replies View RelatedI just installed OpenSuse 11.1 alongside of Ubuntu 9.10. After finishing up the installation I find that I can't get into Ubuntu. I have tried adding Ubuntu to the OpenSuse /boo/grub/menu.lst but it doesn't seem to be working.
View 9 Replies View RelatedI'm finally getting around to configuring my Xfce desktop environment and I'm having a lot of trouble having applications remember their last position. I did some Googling and found this is either not a supported feature or it depends on the application if they want to support it or not.
I'm trying to make my default terminal start in the center of the screen.
I found that you can add the command line parameter
Code:
For example and it should open at a 70x20 size in the 20+30 position. I added that to my panel launcher's command and ended up with
Code:
However the terminal isn't opening at all.
After further reading, I discovered the default launchers use your preferred applications so I just used replaced the launch command with the following and it worked perfectly:
Code:
I tried to install emergent using following guide:[URL](Ubuntu) However, I did not succeed, it seems that it could not install emergent properly. My far worse problem now is that it messed up my software center and update manager. I get following error message when starting the software-center:
Code:
Traceback (most recent call last):
File "/usr/share/software-center/softwarecenter/apt/aptcache.py", line 105, in open
self._cache = apt.Cache(GtkMainIterationProgress())
File "/usr/lib/python2.6/dist-packages/apt/cache.py", line 88, in __init__
[code]....
Could not initialize the package information An unresolvable problem occurred while initializing the package information. Please report this bug against the 'update-manager' package and include the following error message: 'E:Malformed line 59 in source list /etc/apt/sources.list (dist parse)'
I just set up denyhosts and it worked properly the first time adding lots of ips to the hosts.deny.I then set it to run every 12 hours noon and midnight.I wanted to see if ran properly and I got all this.Does it look like its working?
Code:
May 15 12:00:01 hyrule CRON[14286]: (root) CMD (python /usr/share/denyhosts/denyhosts_ctl.py -c /usr/share/denyhosts/denyhosts.cfg )
[code]...
Getting the following error when trying to add a default gateway for eth1.
# route add default gw 192.168.228.2 eth1
route: SIOCADDRT: Network is unreachable
I'm thinking of setting up my own sms gateway using my own linux server and regular old nokia phone, along the lines of what is described here [URL]
I was wondering if anyone out there has been down this road before, and in particular knows about approximately how many messages could be sent/received per minute? In the application I have in mind (an instantaneous online survey from an audience of hundreds) I would need to be receiving hundreds of sms texts in around a minute. I was wondering if that was pushing it in terms of the capabilities of an old phone.
As per the subject really, is it possible to configure sendmail to use my ISP's SMTP gateway? If so, how?
View 10 Replies View RelatedWe are using Linux machine as a gateway server to connect our local network to wan. We use pptp vpn to connect our remote customers network, is it possible to connect VPN to the gateway and make local network to connect through it? So that there is no need to connect vpn in every local client.
View 3 Replies View RelatedI am accessing internet through Analog Proxy. ADSL modem has been connect to one of windows xp machine and by running Analog proxy, we uses internet by mentioning that machine's ip address. But how do i ping the default gateway in this case? Is it possible or not? If yes then please tell me how, because if i says # ping <anysite.com> it not pinging; its says host unreachable; means i will not be able to run wget too.
I am trying to ping from OEL 5.3. In one of google link; i read that :Does PING work through the Proxy Server? No, ping uses the ICMP protocol to communicate. Proxy only supports TCP and UDP packets. Ping will resolve the DNS name but go no further.
in fedora/redhat system I want to add IP address along with Default Gateway and DNS.For assigning IP to eth0 i use the command # ifconfig etho 192.168.1.10 subnet mask 255.255.255.0 upthis remain temporary and when I restart my system it lost the IP address. Well to permanently add IP address in etho I use the file #cd /etc/sysconfig/network-scripts and then use # vi ifcg-eth0 to add IP address and Network Mask. How can I add Default Gateway and DNS permanently in ifcg-eth0 file or there is any other file for it ?
View 5 Replies View RelatedPossible Duplicate:Forward SSH traffic through a middle machine.I am looking to get an interactive ssh session on a remote machine, but must login via a gateway.For example, right now I do the following:
@local % ssh <user>@<gateway>
@gateway % ssh <user>@<remote>
Is it possible to achieve the same thing in a single command from my local machine? I have tried:
@local % ssh <user>@<gateway> 'ssh <user>@<remote>`
From the output i am indeed able to login, but do not get an interactive session. I took inspiration for this attempt from using ssh to run a command remotely.
I am using debain 6 and using a Sierra modem c888 to connect internet. I am using wvdial package for connecting the modem. I am able to connect internet. The question I have is, how do get the gateway address of the newly created ppp0 interface?
View 1 Replies View RelatedSomeone in my building has placed an old Gateway computer in the trash room. All I know from looking at it is that it says made for Windows XP and its the old tan hue computers use to have. My question is what are the odds that if I go grab it before trash day I could boot up Ubuntu 10.10 or some other current Linux build on it? I just want to use it as a secondary computer and solely for web browsing and possible word processing.
View 9 Replies View RelatedI have configured bonding on 64 bit centos 5.4 I have to put the machine to a different VLAN for that i did the Ip change and restated the network. but i cant ping the gateway or any other server in that network. the cofig files are as follows
vi /etc/modprobe.conf
alias eth0 bnx2
alias eth1 bnx2
alias scsi_hostadapter aacraid
alias scsi_hostadapter1 ata_piix
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
alias bond0 bonding
options bonding mode=1 miimon=100
[Code].....