General :: Unable To Add Default Gateway And DNS
Jun 18, 2010
in fedora/redhat system I want to add IP address along with Default Gateway and DNS.For assigning IP to eth0 i use the command # ifconfig etho 192.168.1.10 subnet mask 255.255.255.0 upthis remain temporary and when I restart my system it lost the IP address. Well to permanently add IP address in etho I use the file #cd /etc/sysconfig/network-scripts and then use # vi ifcg-eth0 to add IP address and Network Mask. How can I add Default Gateway and DNS permanently in ifcg-eth0 file or there is any other file for it ?
View 5 Replies
ADVERTISEMENT
Dec 19, 2010
I could not able to configure the default gateway ip address onto the system. i use the route command (" route add default gw 192.xxx.xxx.xxx eth0 ") to add a default gateway onto the routing table but it is "disappear" in the routing table when i had restart the service network.
View 3 Replies
View Related
Aug 10, 2010
Getting the following error when trying to add a default gateway for eth1.
# route add default gw 192.168.228.2 eth1
route: SIOCADDRT: Network is unreachable
View 2 Replies
View Related
Jul 17, 2011
I installed openSUSE on one of my work system. The network port wasn't working when I was installing, but works fine now (checked in Windows). But for some reason, I am not able to configure the network. I used both Dynamic and Static IPs (both work fine in Windows) but still no go. I am using Yast Control Center for this purpose. I can't even ping the default gateway when I am using custom settings. When I use dynamic settings, it says Unreachable Network.
View 7 Replies
View Related
Jan 20, 2011
i have a leased line ( speed 2 MB ) which we use to connect to our mail server , oracle ERP etc.. we have a dhcp scope defined as 192.168.100.1-192.168.101.254. with a default gateway as 192.168.100.90 ( which is a cisco router ) we have a pix firewall ( 192.168.100.10 ).. now the gateway passed all the request to firewall..we have an ADSL of 4 MB speed.. ip is 83.*.*.230 from ISP. i have a proxy server ( squid ) eth0 is connected to ISP (83.*.*.230).. eth1 to LAN ( 192.168.100.79 ) now the problem is when i put default gateway to eth1 ie 192.168.100.90 the squid connects to internet via leased line.. if i leave the default gateway field empty on eth1 , the squid connects to internet via ADSL ( which i want ) but the problem is no one on the lan cant ping the squid server ( no connectivity to internet for the whole LAN ) how can i solve this problem? PS : i want squid to connect to internet with ADSL, but if i put gateway on eth1 ie LAN squid goes through leased line which i dont want to happen
View 1 Replies
View Related
Aug 9, 2011
I have a CentOS running. It is important to have my CentOS available when I am remotely connected to a VPN router. I tried to add a default gateway to the VPN router, but after reboot it goes away. How can i put this as permanent?
ip route add 192.168.2.3 via 10.0.0.1 dev eth0
View 2 Replies
View Related
May 28, 2010
I want to set default gateway permanently. There are two files and both have keyword "gateway":
Code:
View 2 Replies
View Related
Feb 3, 2011
This is slackware 12. I'm trying to share my internet connection (on eth0) with a computer connected to eth1.
eth0 is 192.168.0.101, eth1 is 192.168.1.100 (different subnets).
But when I try to make eth1's default gateway the same as eth0's, see the error I get code...
View 7 Replies
View Related
Jan 8, 2010
I am in a big confusion and searching an answer to calm down my mind.I have my eth0 has following configuration
` ` `
IP 192.168.1.100
mask 255.255.255.0
[code]....
View 3 Replies
View Related
Jul 29, 2011
I recently switched from Ubuntu server to Debian server, and I carried over many of the same configurations. This is pretty much a fresh install.
I cannot get the default gateway to stick by using the /etc/network/interfaces. I can ping my default gateway but nothing beyond it either by name or IP. code...
I would like the default gateway to stick between reboots. Could someone point me in the right direction?
View 4 Replies
View Related
Feb 23, 2010
I have installed ubuntu 9.04 Jaunty server from disk. I am connect to my corporate internet. I have put in my http_proxy everywhere I can find to put it. I am getting an ipaddress, gateway, broadcast,etc. My wired is connected. When I try to ping my default gateway it times out. %100 packet loss. I get the ipaddress of the gateway from the (route command).
My configurations on /etc/network/interfaces is correct(I am on another computer so I can't copy and paste) and I even tried updating the drivers for NIC card. I am using a Intel 82567LM-3. I have been working on this longer than I care to admit.
View 7 Replies
View Related
Jun 28, 2010
I'm having some difficulty with a internet/vpn setup. I have 3 network adapters on the server. 1x is used to connect it to the rest of the network 1x is used to provide internet (squid,dansguardian) 1x is used to connect to the vpn router
My interfaces file looks like this:
Code:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
[Code]...
The problem that I have is this: When the gateway on eth2 is set to 10.0.2.2 the VPN works 100% but there is no internet. When the gateway on eth2 is set to 192.168.0.6 there is internet but no VPN.
So what I want to do is, route all traffic that is supposed to go to 10.0.2.0/24 and 10.0.3.0/24 to eth2 and all internet traffic to eth0.
View 6 Replies
View Related
Jul 11, 2009
I have installed eeebuntu NBR on my laptop and it looks great on a 17 inch widescreen. It looks so different from the usual interface that I get people ask about it and I can evangalise without being considered a boring weirdo! Anyway, I have one problem. Every time I boot I have to run the following command.
Code: sudo /sbin/route add default gateway 192.168.0.1
How do I get this to happen automatically (as it normally does)?
View 3 Replies
View Related
May 4, 2011
Im trying to achieve the multiple uplinks/provider found on LARTC.org. I have to get the IP addresses from my interfaces (EF1 and EF2) by using a script, but i dont know where to look at for the default gateway from each interface which got their ip address from my ISP.
View 1 Replies
View Related
Apr 11, 2010
I have a computer with two interfaces: a fixed connection (eth1) and a modem (ppp0). My goal is to receive UDP packets from both connections concurrently (using the recv() function). The problem is, that the received packets reach the application only when the default gateway is set to that interface's address. For example, if I set the default gw to be in the eth1 subnet, only packets from eth1 reach the application. Other packets are received in the interface (checked using tcpdump), but they seem to be blocked somewhere. The policy defined in iptables is "ACCEPT" for all incoming packets, with no rules at all. I would like to know how to overcome this problem, and anyway how is the default gateway related to incoming UDP?
View 3 Replies
View Related
Nov 11, 2010
I have a dual-homed Debian server running squid, but not acting as a router. Simplied network diagram is below - there are other local hops between the gateways and the Internet.
Code:
(eth0 @ 192.168.44.2) <--> (Gateway1 @ 192.168.44.1) <--> Internet
(eth1 @ 192.168.55.2) <--> (Gateway2 @ 192.168.55.1) <--> Internet
Using Gateway1 gives a very fast, but not always reliable route to the Internet. Using Gateway2 gives a slower, but more reliable route to the Internet. The server uses Gateway1 as the default gateway.
I have written a script that pings three hosts on the Internet, and if all three are down, switches the default gateway to Gateway2. This part seems to be easy, but I'd like know if there is a way of routing a ICMP/ping out eth0 to a host, with all other traffic to the host going out eth1, so I can determine if the Internet is reachable via Gateway1 again.
View 2 Replies
View Related
Apr 7, 2010
I am realtively new to BGP. I use BGP in my network to advertise my /20 subnet. What i would like to know is what is the point of accepting routes from your neighbouring AS(ISP)?My ISP has given me a default gateway, and no matter what I want to reach on the internet I have to go through that default gateway, so why populate the routing table with soo many routes?also, as i understand it, there are 3 kinds of routes that you can accept, those are full routes, directly connected routes and default routes. What is the diffrence between them and again how do they affect routing since my network only has the one default gateway?
View 2 Replies
View Related
Jul 14, 2010
after a reboot of my Lenny system, the default gateway will lost. Then i must try "networking restart" and the gatway will be set
my interfaces looks :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
[Code].....
View 1 Replies
View Related
Jan 30, 2011
I had a router crap out yesterday. I'd been testing out a new one for the last few days and just reconfigured it to be the main. Took the old one down and everything in my house (Windows 7 PC, XP Files server, Ubuntu PC , windows 7 laptop, android tablet, ps3, etc) seems to be working fine whether it be hard wired or wifi. All except my ubuntu 10.04 laptop. It worked fine before the swap so I can't figure out what's going on.
I'm able to connect to the new SSID without issue but I can't resolve any external names and when I try to ping the default gate way every other packet has (DUP!) behind it. If I'm hardwired I don't get the dup! when pinging the default gateway but I still can't resolve any external names. I have provided the results of an ifconfig and the results of a ping to the default gateway below.
cooley@Quigon:~$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=2.98 ms
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=3.04 ms (DUP!)
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=3.50 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.72 ms (DUP!)
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=8.09 ms
[Code]...
View 9 Replies
View Related
Jul 2, 2010
I posted it on another forum, but could not get response,So I have this cenOS, Ubuntu and windows operating system running on virtual machines.Now I gave them manual ip address, both ubuntu and windows machines can ping the default gateway, but not the CentOS.It should forward 0.0.0.0. to my cisco router address(192.168.5.254),
View 4 Replies
View Related
Feb 21, 2011
I'm looking for a method to assign a default gateway via dhcp randomly depending on ether the last char of the mac being odd or even, or the time the user connects. Is there a good reliable way to achieve this?
View 2 Replies
View Related
Jun 16, 2011
I have installed dhcp-server on ubuntu. And server is providing ip address to clients (Window machines) but not default-gateway but I have another network in my network and same configuration and same dhcp-server provides every information.
View 5 Replies
View Related
Apr 15, 2010
I am looking for a way to delete the systems default gateway from the routing table via the NETLINK API.Unfortunately, the documentation I found about NETLINK is incomplete.There are some basics (communicating with the kernel, reading the routing table) but not much more.Does anyone know the packet format for deleting a routing table entry, especially deleting the default gateway? I can set or change the default gateway with the following parameters (there are more, but I left out all the non-essential ones):
NL-Msg Header:
nlmsg_flags = NLM_F_REQUEST | NLM_F_CREATE;
nlmsg_type = RTM_NEWROUTE;
[code]....
View 1 Replies
View Related
Nov 1, 2010
I recently upgraded a 11.0 installation running on Xen Server to 11.3. I am experiencing frequent network disconnections now. The ip address and default gateway is assigned statically. However, the system seems to ignore the default gateway after a while. Then after several minutes it seems like it comes back.
Code:
root@poe5e:~/ > route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.111.0 * 255.255.255.0 U 0 0 0 eth1
172.16.107.0 * 255.255.255.0 U 0 0 0 eth0
link-local * 255.255.0.0 U 0 0 0 eth0
loopback * 255.0.0.0 U 0 0 0 lo
default 172.16.107.254 0.0.0.0 UG 0 0 0 eth0
root@poe5e:~/ > ping 172.16.107.254
PING 172.16.107.254 (172.16.107.254) 56(84) bytes of data.
64 bytes from 172.16.107.254: icmp_seq=1 ttl=255 time=0.515 ms
64 bytes from 172.16.107.254: icmp_seq=2 ttl=255 time=0.484 ms
64 bytes from 172.16.107.254: icmp_seq=3 ttl=255 time=0.496 ms
64 bytes from 172.16.107.254: icmp_seq=4 ttl=255 time=0.473 ms
^C
--- 172.16.107.254 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 2997ms
rtt min/avg/max/mdev = 0.473/0.492/0.515/0.015 ms
root@poe5e:~/ > traceroute orl3akm1n
traceroute to orl3akm1n (10.111.19.19), 30 hops max, 40 byte packets using UDP
1 172.16.107.250 (172.16.107.250) 0.405 ms 0.398 ms 0.357 ms
2 * * *
When my sessions suddenly die and I have to coax it into routing correctly again.
View 1 Replies
View Related
Jun 25, 2010
i have setup an open vpn server and when i connect to it the client pulls an IP and but not default gateway. My goal is to route all web traffic through the VPN... My config file looks like this...
Code:
dev tun
proto tcp
port 1194
ca /etc/openvpn/easy-rsa/keys/ca.crt
[code].....
View 2 Replies
View Related
Mar 9, 2011
Struggling to get my Linux server accept ICMP redirects not originating from default gateway. No problem to get it working if the redirects is originating from def gw.I know it's not a good solution security wise, but my network is so cluttered I'm forced to do so.
View 1 Replies
View Related
Nov 26, 2009
Client which uses an ISP with a Linux machine (Server 1) with two network cards. Eth0 with ip 1.1.1.2 and gateway 1.1.1.1 these ip's is not public ip's and falls unders the isp's internal range, eth1 with the internal ip range. OpenVPN listen on eth0 for incoming connections. We want to connect to Server1 from external networks. Due to different reasons the isp could not get the routing sorted and give us an public ip on his network. We had to setup another bos (Server2) with eth0 2.2.2.5 and gateway 2.2.2.1 which is public ip's and eth1 with ip 3.3.3.5. Server 2 can communicate via the ISP internal network with server 1. I use DNAT to forward all incoming connections on server 2 to server 1 but the problem I have is that server uses its default gateway for the return packages and does not sent the reply back to server 2. My iptables rules looks as follows on server 2.
/usr/sbin/iptables -t nat -A PREROUTING -p udp -i eth0 -d 196.25.157.135 --dport 1194 -j DNAT --to 192.168.100.170:1194
/usr/sbin/iptables -A FORWARD -p udp -i eth0 -d 192.168.100.170 --dport 1194 -j ACCEPT
View 5 Replies
View Related
Apr 22, 2009
I'm using OpenWRT on a WRT54GS. I'm using wifidog in combination with openvpn. For those of you familiar with wifidog, my auth server is located at the other end of an openvpn tunnel and the "wifi dog gateway" is running on the WRT itself. I'm don't really think that wifi dog is the issue. Basically, I'm using openvpn with the "redirect-gateway" option which works well. In this mode, openvpn removes my current default gateway setting and adds the remote openvpn server as the default gateway (as it should). However, overnight, my default gateway on the local network keeps reapperaing (along with the openvpn one as well).
This causes confusion and I don't want any packets (But ovbiously the connection to the actual openvpn server) to go down this local gateway. Why do you think it reappears? Do you reckon openvpn is dropping connection and somehow the normal gateway is being added back? I *could* run a cron script which runs every minute or so with something like "route del default gw xx.xx.xx.xx" (where xx.xx.xx.xx is the default gateway which I don't want to be there) but that is quite messy and means that if I were to ever move the router I would need to reconfigure this and considering that I would like in the future to have many of these wifi dog gateways, this really isn't an ideal option (as every network will have a different default gateway).
View 2 Replies
View Related
Oct 21, 2010
I've been struggeling with this for a few hours now, googleing and so on trying to find an easy way to just switch which device I want as primary for internet connections. After long battles I'm at a loss, this is the current automatic routing
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
85.225.76.0 0.0.0.0 255.255.252.0 U 1 0 0 eth0
85.225.76.0 0.0.0.0 255.255.252.0 U 2 0 0 wlan0
[Code]...
View 1 Replies
View Related
Jun 29, 2011
I need to place an Ubuntu machine on a network where I have a DHCP server which does not configure the Degault Gateway parameter (we don't want ordinary users to browse the internet). Is it possible to leave the machine using DHCP and define the Default Gateway manually (as in Windows XP i.e.)? How?
View 1 Replies
View Related
