General :: Activating Belkin Usb Wireless F5d7050 ?
Dec 11, 2010
Trying to add wireless adapter to my fedora 13 system. Belkin f5d7050 raxwn450th v4000. Located zydas zd1211 driver on source forge. Downloaded and installed it
Code:
showed my dsl wireless adapter
system - preferences - network connections did not show it
I rebooted - now
Code:
shows my dsl adapter, and lsusb says
Code:
But it not show up on system - preferences - network connections
Would have prefered to install it via yum but dont know the magic words to get yum to find it.
View 1 Replies
ADVERTISEMENT
Mar 27, 2011
Following sticky Thread: Getting Your Wireless to Work - Everything seems okay through step VI, getting an IP address through DHCP. It appears that authorization is failing. Results from steps in sticky:
Note: This is a new installation of openSUSE on fresh (formatted) workstation
Step II What device? Hardware info from YAST - Wireless LANUSB2.0 WLAN (wlan0)Kernel Driver: zd1211rw lsusb reports "Bus 001 Device 002: ID 050d:705c Belkin Components F5D7050 Wireless G Adapter v4000 [Zydas ZD1211B]"
Step III External firmware? I downloaded the b43 packages, installed as normal and used etc/SysConfig editor to add b43 to modules loaded on boot.
dmesg|grep firmware
[ 22.468807] zd1211rw 1-3:1.0: firmware version 4725
Ran the following check from another thread
rfkill list all
0: phy0: Wireless LAN
[code]....
View 9 Replies
View Related
Dec 15, 2010
I have a Belkin G Wireless USB Network Adapter that I cannot get working for the life of me...USB adapter hardware: F5D7050 Ver. 3136 (v3000) Below are ouputs after a fresh install... Then I tried to install the newest drivers from ralink [URL] I blacklisted the current drivers and installed these and everything looked the same as before. Even if i blacklist the 3 drivers
rt2500usb
rt2x00lib
rt2x00usb
They are still loading at boot. Is there any way to make this work. I would try ndiswrapper but even when blacklisting those above, they are still loading.
System: HP G50 Laptop with on-board atheros card that used to work, but now even has issues in windows
Code:
$ lspci
Code:
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Code:
$ lsusb
Code:
Bus 002 Device 002: ID 050d:705a Belkin Components F5D7050 Wireless G Adapter v3000 [Ralink RT2573] With a fresh F14 install, I plug the device in, does not light up or work, yet shows in network manager
Wireless Network (Atheros 5001 Wireless Network Adapter)
wireless is disabled
Wireless Network (Belkin 54g USB Network Adapter)
wireless is disabled
I cannot click on either of these. So I check dmesg...
Code:
$ dmesg
Code:
[ 736.739057] usb 2-3: new high speed USB device using ehci_hcd and address 2
[ 737.026971] usb 2-3: New USB device found, idVendor=050d, idProduct=705a
[ 737.026978] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[code].....
View 4 Replies
View Related
Dec 23, 2009
Cannot Connect to a wireless network using a USB Belkin 802.11g Model F5D7050: Setting up a new pc is running opensuse 11.2 (i586) KDE 4.3.1
Question1) The HCL shows a version, how do I find what version i have?
Question2) Why is rt73.bin not being loaded? I ask this because the file is located in Root/lib/firmware
Question3) Why is Configure Desktop > Network Manager > Wifi is blanked out as if doesnt exist?
Question 4) when using YAST > Network Settings > Initially under wireless network card configuration I can scan the area and find networks successfully (I got 2, one as a wifii hotspot from my pda cell phone, the other is the standard wireless network for laptops and such).... but if i use kinternet >wlan0 > wireless connection, nothing will be found! I did a search on the /var/bootlog msg for "switch" and "radio", for radio I found the following:
<6>[ 9.108858] Registered led device: rt73usb-phy1::radio
<6>[ 9.108884] Registered led device: rt73usb-phy1::assoc
<6>[ 9.108909] Registered led device: rt73usb-phy1::quality
<6>[ 9.109386] usbcore: registered new interface driver rt73usb
[Code].....
View 1 Replies
View Related
Jan 3, 2011
i am complitly new in Ubuntu and the world of Linux in general, so i said to my self its better late then never, i installed the last one 10.10. but i am having trouble with my wifi usb adapter (BelkinF5D7050 v 1000), the same adapter works perfect under XP in the same PC. when i go to NM i dont see it in the list of network cards "i see just my two other normal network cards + loopback" and i have permanent small "x" on the icon of NM up in the task bar, even if check or uncheck "Enable Networking", it alwayes show a info bubble "you are now offline", here is the result of all the command line that can help getting better view on my problem
[Code]....
View 1 Replies
View Related
Apr 13, 2011
I recently installed the latest and greatest Lubuntu 64 bit, because I like lxde and I am planning a system migration. (I am really starting to not like windows 7.) I have some linux experience. I wouldn't say I am awesome at it, but I am comfortable trying anything.
Example: I have used CENTOS 5.6 to make a linux machine server as a glorified router, with asterisks, SIP, SSH server, x windows, GNome, VNC, and a user authentication system. and get this I walked somebody through setting this up over the phone. I reopened the root account (I honestly got tired of typing sudo every other command is the only reason why I opened it.) I plan on closing it after we are done.
lsusb lists the wireless adaptor
Wireless Card Link
[[URL]
I have the driver CD. I installed ndiswrapper.I copied the files from my driver cd to my <home> Directory. Then installed the Windows XP version of the drivers using ndiswrapper -l <driver>. I then made ndiswrapper force the driver to the vendor ID of the wireless card. Using ndiswrapper -a <vendor ID> <Driver>(I did this last night and the vendor ID escapes me. I am at work now.)I finally ran depmod -a and modprobe ndiswrapperI goto the windows wireless driver application, and it shows the driver as loaded and the hardware as found.
However, it still does not list a wireless device in the network manager to where I can connect to my wireless. iwconfig does not show any wireless LAN, but it is still listed in lsusb. Also, the light that shows activity on the wireless device does not light up or blink at all. I have about 6 usb ports on my desktop and have tried everyone. The wireless card also works in Windows 7 64-bit On a strange side note. I do have internet access through LAN, (My laptop is atm a glorified wireless card .)
View 4 Replies
View Related
Jan 1, 2011
I am new to ubuntu and am trying to connect to the Internet with a usb wireless from belkin. Attached is the wireless_setup.txt.
View 2 Replies
View Related
Nov 25, 2010
I have recently installed openSUSE 11.3 I have a Belkin G Wireless Network Adaptor
Model: F5D7050
FCC ID: K7SF5D7050E
Linux doesn't seem to recognise this device at all. I had a look online from another PC for drivers. and they are provided by Belkin themselfs but only for Windows XP/Vista.Is it possible to get this working on openSUSE. I previously used this very same adaptor on an Unbuntu 10.2 PC and it worked with no problems at all.
View 1 Replies
View Related
Jan 10, 2010
I have had some experience with ubuntu on my Lenovo y730. I was told to run debian on my dell 2650 for the compatibility, All I want is to be able to run either my Belkin pre n f5d8010 pcmcia card or a linksys usb wifi.
View 1 Replies
View Related
Mar 11, 2010
I have a Belkin Wireless G USB Network Adapter but I cant get on the internet with it.The laptop is running Damn Small Linux.Heres what is going on and the code I typed:
ndiswrapper -i rt73.INF
ndiswrapper -l
modprobe ndiswrapper
iwconfig
ndiswrapper says the driver and hardware are present but iwconfig and ifconfig don't say anything.The wireless adapter works fine in windows 2000 and windows xp with the same driver.The green LED on the wireless adapter never flashes like it is supposed to.
View 3 Replies
View Related
Jun 12, 2010
I'm pretty new to Linux, but have had a bit of functional tutoring. i'm triple booting my old Dimension 8400. Have been running with Jackalope and XP for some time now and wanted to install Lynx and get a good handle on it before i completely wipe my other machine (Win7/Jackalope) and install it there.
Installed Lynx from a USB stick and all seems well, it recognises the UBS wireless and all available connections but just sits and spins on the password login and never connects...hmmm. I have tried all possible combinations of rebooting with the USB connected/disconnected/connecting after... to no avail.
The wireless seems to "work out of the box" just as seamlessly as it did for Jackalope, all the steps are similar, it just never connects.
View 6 Replies
View Related
May 6, 2011
I've been having problems with connecting to my router with my wireless card. Sometimes knetworkmanager attempts to the connect to my wireless via it's saved profile but it just stays on "Activating" for about 45 seconds then just stops. This only started happening a few days ago, so maybe the new kernel update has something to do with it?
I've tried to debugging the problem myself and have found if I reboot my router knetworkmanager can connect immediately to the wireless router, but also something interesting I found was is I assigned a IP Address and DNS manually on the saved profile it would connect with no problem (No reboot of router required), so it is indicating there is a problem with getting network settings. I've confirmed that the wireless card is not hard or soft blocked through rfkill.
I was using the box standard ath5k driver when this problem started happening and even went as far as a complete reinstall but ironically enough on first boot from a fresh install my wireless could not connect with the problem described above. I've since moved to the compat-wireless drivers but the problem remains.
I checked a couple of logs, one log file of significance was the wpa_suppliment log which was full of these messages: From all my debugging I can only assume that the kernel update is a possible cause for all of this as the problem occurring on first boot of a fresh install sounds like a general bug. I've got all of the requested information about my wireless card below, hope I've got everything:
[Code]....
View 2 Replies
View Related
Jan 20, 2011
I use openSUSE 11.3 with KDE 4.4 and I have a Belkin Share Wireless USB Adapter (F7D2101 v1) , I attached the adapter and rebooted the system, it does not work. Can someone help me configure?
I attached the adapter and the system says:
dmesg | tail
[ 1184.799076] usb 1-1: USB disconnect, address 2
[ 2003.060031] usb 1-1: new high speed USB device using ehci_hcd and address 7
[ 2003.194525] usb 1-1: New USB device found, idVendor=050d, idProduct=845a
[ 2003.194531] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2003.194535] usb 1-1: Product: Connect Wireless USB Adapter
[Code]...
View 9 Replies
View Related
Apr 1, 2011
I'd like to know how can I find a Linux wirelles driver for wireless Belkin card.
View 1 Replies
View Related
Feb 3, 2010
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
View 1 Replies
View Related
May 26, 2010
configure my Belkin Wireless USB adapter(F7D2101)? I attached the adapter and rebooted the system. I used the hardware info and it is listed but no drivers.
View 4 Replies
View Related
Jun 16, 2010
I have a Belkin F5D8055au USB wireless adapter which I can't configure in YAST. I have downloaded the RT2870sta driver from RALink and compiled it - seemed to be ok. Modprobe loads it ok. Some info:
[Code]...
When I open network settings in YAST my wired (ethernet) card shows up but not the USB. If I manually add a wireless card, I can't select the kernel module from the drop down list - there is nothing in it. At that point I abort YAST. So, how do I convince YAST that there really is a USB wireless adapter connected?
View 9 Replies
View Related
May 14, 2010
Code:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[Code].....
I've read around blacklisting but I'm not sure on what I should be blacklisting really.
View 9 Replies
View Related
Aug 27, 2011
I am trying to get a netgear wireless usb card to work correctly. I have installed ndiswrapper and gotten the correct drivers installed. The device does show up with lsusb. I can't seem to figure out how to get the wireless card to show up in gnome to start using it.
Update: the ndiswrapper module does load but when i run ndiswrapper -l it just shows the driver installed but, it is not showing my wireless usb card (0846:9020).
View 6 Replies
View Related
Jan 20, 2010
This must be a repost, but I still want to ask, how do I activate the wireless on my laptop? I've been given advice about this a while back, but forgot. Just reinstalled a fresh copy of 9.10
Or is there an alternative way to do this?
View 7 Replies
View Related
Mar 13, 2009
Is there an easy way (or even a hard way) to activate wireless network capability from the command prompt? I want to do this because I like to use the fvwm window manager, but I also like wireless! (In fvwm wireless networking doesn't start up automatically.)
I tried just starting the wireless by...
Code:
Despite the promising messages, wireless didn't work.
View 14 Replies
View Related
Feb 7, 2010
I'm fairly new to Ubuntu. I'm struggling to enable wireless on my Acer Travelmate 2480. Wireless was turned on and off in Windows with a button which does nothing in Ubuntu.I think I must be missing drivers or something, but how do I get them if I can't connect to the internet?
View 2 Replies
View Related
Dec 10, 2010
Is it any way of activating my wireless without using the external switch of laptop (currently broken)?
If yes how can I memorize this action so that each time I boot it will be automatically open?
I am using Ubuntu 10.10. In previous versions wireless was always activated.
View 3 Replies
View Related
Mar 11, 2011
I'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies
View Related
Jul 26, 2010
im downloading ubuntu for m desktop...my question is how do i listin to my music..and can i use m belkin usb wireless adapter??? does ubuntu have drivers for such things?
View 4 Replies
View Related
Aug 6, 2010
I just moved to Linux, and I really need some help for my wireless adapter. What I am using is Belkin F6D4050 v2. I think I should use the rt2870sta driver. After 2 days working, my laptop can recognize the wireless adapter now. But it can not find any wireless connections. There are some information. Hope they are useful.
[Code]...
View 9 Replies
View Related
Sep 6, 2011
I have gotten this to work on Xubuntu here: [SOLVED] Ndiswrapper? Does it work? - Ubuntu Forums.I think it would use the same software/firmware? I am using OpenSUSE 11.4 LXDE derivative.
View 4 Replies
View Related
Sep 29, 2010
I have a Belkin F5D6050 adapter, which (despite being only 11b) was working better than my 11n adapter on 11.1 [The 11n stopped working today after I ran an upgrade; I have got it working - in a fashion under 11.3 - see RTL819SU not working with ifup (needs ifup-dhcp first)] I can't connect to my AP. The significant output from dmesg appears to be:
Code:
[19991.327361] wlan1: authenticate with 1c:af:f7:26:01:bc (try 1)
[19991.524037] wlan1: authenticate with 1c:af:f7:26:01:bc (try 2)
[19991.724034] wlan1: authenticate with 1c:af:f7:26:01:bc (try 3)
[19991.924031] wlan1: authentication with 1c:af:f7:26:01:bc timed out
FYI the info from
[Code]...
View 2 Replies
View Related
May 2, 2010
I've got an old IBM Thinkpad T41 that I just play around with Ubuntu on. The internal Wireless card is broken, so I bought a Belkin F5D8013 PCMCIA Wireless N card a while ago. It worked fine with Ubuntu 8.04-9.10, but it will not work with 10.04. It sees the networks just fine and will let me type in the network password, but it will not connect. Everything else in my house connects without a hitch, so I know it is Ubuntu causing the problem.
View 1 Replies
View Related
May 4, 2010
I have been trying to get my Belkin FD8233-4v3 wireless-n usb adapter to work in Ubuntu since 8.04. It has worked with ndiswrapper under 32-bit (never the 64-bit) versions in the past, but has never been able to be configured directly. It uses the Ralink RT2870 chipset, but cannot seem to be configured using the drivers from the Ralink website.
With Ubuntu 10.04 64-Bit, everything has changed. I have high hopes that this adapter may finally work correctly and without ndiswrapper. As soon as I first booted 10.04, for the first time ever, Ubuntu recognized the IF automatically, reported my wireless router, allowed me to enter my 128-bit WEP hex code and tried to connect up. It is failing miserably, but it is making a valiant effort.
View 4 Replies
View Related
