General :: Scrim Bridge Keeps Crashing (Fedora 12)?
Apr 14, 2010
Could someone please explain to me what Scrim Bridge is and how to correctly/disable it since I keep getting a warning message that Scrim Bridge has crashed.The message goes like this:warning: .dynamic section for "/lib/libc.so.6" is not at the expected addresswarning: difference appears to be caused by prelink, adjusting expectationsCore was generated by `scim-bridge'.Program terminated with signal 11, Segmentation fault.
I want to set up a bridge using bridge-utils within /etc/network/interfaces like is shown here in this guide: [URL] The problem is that, at the same time, I want eth0 to have a specific static IP address. Right now I have a configuration for eth0. This guide tells me that I should not configure eth0 outside of the br0 configuration.
I have 2 NIC's in a box. One of them is external and doesn't matter for this question I don't think.
The other NIC is 192.168.100.3. It hosts an iSCSI Target and SMB Share on my LAN. It's works great.
I have another PC that has NIC at 192.168.100.101 and it hosts my DHCP (Scope: 192.168.100.5-25) server for my LAN.
I have a hardware firewall at 192.168.100.1 and it serves inet to the LAN on a different external connection.
So...
I currently have a WAP (cheap p.o.s. netgear router in WAP mode that keeps overheating). I want to eliminate the WAP device and add a WiFi NIC to the Top PC above.
So, on the first system I would have:
NIC 1: External IP and External Gateway NIC 2: Static IP 192.168.100.3 Proposed WiFi NIC 3: Static 192.168.100.4
Then I simply put the WiFi in Ad Hoc, will another WiFi in Ad Hoc (for example my laptop) be able to "see" 192.168.100.101 (DHCP) & 192.168.100.1 (Gateway) (via WiFI 192.168.100.4 through the bridge to 192.168.100.3 and on to the LAN)?
Also, can the two NIC's be bridge together even though they are the SAME subnet?
I tried google but without success. I have a small home network and one computer has to work as a bridge (comp1), it connects to the internet through wlan and is connected with cable to other computer (comp2), I would like to to make that second computer member of a local network with internet access.I was trying this:
I want to connect my dataone broadband connection in bridge mode in fedora 7. As i am currently using a bridge connection through this modem (smartAX MT882) in win XP, i want a bridge connection in fedora 7 too to access the internet from linux. I have gone through some forums discussing this issue. somewhere i have found the option "adsl - setup" and tried it in my fedora 7. But it is showing the message "adsl- command not found" on this issue. I need a detail step by step procedure for brigde connection using datone in fedora 7.
I'm trying to set up a Linux box with three ethernet interfaces as a bridge where I can do some packet filtering. I don't want this box to have any IP stack, packets that are allowed through the filter should be forwarded without changes just the way a switch would do it. I have build a kernel with ethernet support but no IP stack. It detects my interfaces, and I can bring them up with the ifconfig or ip commands. But when I try to start a bridge with brctl I get this error message:
can't setup bridge control: Address family not supported by protocol
A google search for that error message gave me no results at all. The command I used was "brctl addbr br", which does work on a full installation. Does brctl require IP support in the kernel? That would be a bit odd I think, since brctl doesn't do anything IP related, everything it does is at lower layers?
Does anybody know what the above message means, and what I might have been doing wrong?
I'm sure this is a bridging issue and there is just some option I'm not setting correctly. Also, the reason I'm connecting the Xbox 360 directly to the linux box and not to the router is for traffic monitoring purposes. Note that all connections and functionality work perfectly when the Xbox IS connected through the router.
My current network setup at home is all wired, and that's worked for me so far. Now I want to set up a wireless connection on my Linux box that I can connect to with both my laptop and my Nintendo DS. I'd like to be able to host a wireless network from the Linux box, connect to it with some other wireless device, and have the wireless device communicate with the router, the internet, and other computers on the wired network. I have the wired network set up (statically configured) as eth0. Other network adapters present on the system are eth1 (not in use) and wlan0, wlan1, and wlan2 (identical cards, remnants from the last time I experimented with wireless).
So I guess my question comes in two parts: 1) How do I set up wlan0 such that it can host? Is Ad-hoc mode okay for this, or do I need to set it up in Master mode? 2) How do I forward connections between the wireless net and the router? Note that I will be using WEP, as it is all that the NDS supports. I'd like to set up MAC filtering as well, but not until after I get something that works.
"I am new to Linux. Could you please guide me how to make ADSL bridge connection. I have tried to make connection using Network manager. But, it some times works and some times doesn't works."
I'm in the process of switching back to Fedora after years of hiatus, but I can't get my wireless card working. The card itself is an Atheros AR2413, and the problem is that it seems to appear OK in various places, BUT it doesn't detect any networks. I'm on Fedora 14.
client <--> wlan0 <--> computer <--> eth0 <--> internet
i have 2 network connections eth0 wired connected to internet wlan0 wireless (work fine) i have installed hostapd with madwifi and so on oki when i run hostapd the clients see the hot spot oki clients connect with wpa oki network manager run at demand not automatic (keep it for internet help) now i'm a bit lost what do i need is wlan0 give the client an ip (dhcp demand) create a bridge between wlan0 and eth0 steps to create a permanent bridge between wlan0 and eth0
I have setup hostapd and a bridged setup with br0 bridging eth0 and wlan0. The setup works but unfortunately not on bootup. The reason is that the bridge can't add iface wlan0 because it is down for some reason at this time. When hostapd is running (after the network script) the interface is up and can be added to bridge via
I'm having issues with my GigE Marvell NIC. The problems have started recently. Anytime I push network bandwidth over ~9MB/s, I loose all network connectivity. Stopping the network, rmmod'ing and modprobe'ing the sky2 module and then starting the network again does not resolve the issue (even though eth0 dissapears and then comes back). The only non-standard configuration (as far as desktops go) in my network is that I use a bridge so a KVM virtual machine can be exposed directly to the network. I'm currently testing the problem to see if it exists outside of the bridge.
I've just recently installed the latest version of fedora on my machine. I already had win7 64-bit so I did a dual boot with the Fedora live CD using the "use largest amount of free space option"(I had intentionally left 30GB of unallocated space). The problem though is that fedora just keeps_crashing, at any point and very randomly. I didn't have this problem with ubuntu. Fedora can crash right after I initiate the boot sequence, or it can wait until the booting process starts, or the login screens shows up, sometimes it even lets my use the OS but invariably crashes. I've done numerous hard reboots which only seemed to worsen the matter, now I can barely get past login screen. This issue also happened on the live CD, but with perseverance I got fedora running on my computer.
There's an error message that shows up for a second or two right before the boot sequence is initiated, luckily(!) the system crashed at the moment it was showing and I was able to write it down :
pci 0000:01:00.0 : no compatible bridge window for [mem 0xfffe0000-0xffffffff pre f]
Here are my specs:
Intel p965 chipset (i heard this one didn't work well in previous fedora releases, maybe this is the problem?)
I am new to fedora and I've installed fedora 14, I want to know what are the steps to make my machine act as a transparent (IP-less) bridge? Second, after setting the bridge, I want to make all the packets that passes through the bridge execute a servlet filter (to make some tests and add cookies) is it possible? Is there a simpler way to do those tests on the packets and add cookies?
I compiled my own kernel with tun/tap and bridge support. Both modules load fine at boot time (I could read that in the dmesg output). Now I want to use it, and the /dev/net/tun node is not there, so my application gives that error. I'm trying to bridge openvpn connections. Is it possible that udevd is not doing his work?
PS: I'm on a WD MyBook World Ed NAS device. It's ARM, so I cross compiled the kernel from my debian linux machine. I also installed debian on the NAS.)
I am looking at various laptops at the moment and it's appealing to get a quad core (2720QM) when I need the power (yes, I have an application that can utilize many cores in parallel just fine). But, most of the time those extra cores will just there eating battery. Is it possible to switch a few off?
I'm trying to setup openVPN on debian, well this worked. But every client will get the same ip (172.17.0.6 - local it is). how to set my server in bridge mode. I've read about: server-bridge LOCALIP 255.255.0.0 172.17.1.20 172.17.1.100
BUT, my server has no ipv4 address, but only ipv6: 2001:41d0:2:b2d6::542a:74a so I am not sure how I can do this.
I want to add Sandy bridge support to linux 2.6.32.20.I have linux kernel 2.6.32.20 ,and Sandy bridge changes were added from kernel 2.6.33.4.Please can anyone suggest how to backport the kernel support for Sandy bridge.
I had the latest adobe plug in installed in fedora 11, and then recently did a fresh install of fedora 12. The flash usually works fine until I open multiple tabs in firefox and crashes almost immeditely when I open multiple flash videos, though not always.It is not that big of a pain, but it would be nice to have multiple tabs open for the kind of work I do :-).
I log in, and it works perfectly fine until I try to actually use it. As soon as I click to open a chat with someone, it crashes. It wasn't doing this until this morning, and it's given me no problems before now, other than the occasional failure to send messages through.
When it crashes, it brings up the Bug Buddy bug reporting tool. Also, on further testing, it seems to only be doing this when I try to open a chat with my sister, and it does it whether it's recognizing her as being online or not.
i dont know what happens to my fedora 12 firefox browser it keep crashing after 5 minutes. the first one week after installation had no problem but since yesterday it keeps crashing after 5 minutes after start. please tell how to resolve this. and how to update my Mozilla firefox.
Fedora keeps crashing on me. It happens randomly. Sometimes it will give the equivalent of a blue screen for windows. Other times it will just reboot. [URL] Does any of this mean anything to anyone? Would really love to use fedora because I like it a lot an I'm getting familiar with it but it keeps crashing.
Its a fresh install. All I have done so far is installed updates via Yum, including the updated kernel, installed RPM fusion and I installed my wireless drivers.
