I have setup hostapd and a bridged setup with br0 bridging eth0 and wlan0. The setup works but unfortunately not on bootup. The reason is that the bridge can't add iface wlan0 because it is down for some reason at this time. When hostapd is running (after the network script) the interface is up and can be added to bridge via
[Code]....
what i want to do is
client <--> wlan0 <--> computer <--> eth0 <--> internet
i have 2 network connections eth0 wired connected to internet wlan0 wireless (work fine) i have installed hostapd with madwifi and so on oki when i run hostapd the clients see the hot spot oki clients connect with wpa oki network manager run at demand not automatic (keep it for internet help) now i'm a bit lost what do i need is wlan0 give the client an ip (dhcp demand) create a bridge between wlan0 and eth0 steps to create a permanent bridge between wlan0 and eth0
I try to set-up an Access point using ubuntu 11.04. I am using the minimal configuration file from [URL] together with a TP-Link TL-WN422G (Atheros chipset). I've installed the linux-backports-net-natty-generic drivers. But when trying to start hostapd I always get this output:
Code:
# hostapd -dd -K test.conf
Configuration file: test.conf
Failed to set interface wlan0 to master mode.
nl80211 driver initialization failed.
wlan0: Unable to setup interface.
ELOOP: remaining socket: sock=5 eloop_data=0x9b9440 user_data=(nil) handler=0x43d980
I have also disabled the network-manager for this device by adding this to /etc/network/interfaces:
Code:
iface wlan0 inet manual
cat test.conf:
Code:
interface=wlan0
driver=nl80211
ssid=test
channel=1
lsusb says:
Code:
...
Bus 001 Device 005: ID 0cf3:1006 Atheros Communications, Inc. TP-Link TL-WN422G v2 802.11g [Atheros AR9271]
...
lsmo: .....
Code:
Linux magnet 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:24 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
just wondering if I could get a hand with bridging my eth0 and wlan0 connection. I'm using Ubuntu 11.04 if that helps at all.
View 1 Replies View RelatedWhen I try to bring up my wi-fi PCI card (ifup wlan0 or ifconfig wlan0 up) my whole PC just hangs until I power it off.
I believe I have the right drivers, but cannot see what I am doing wrong.
I'd really prefer not to go down the ndiswrapper route.
Firstly, I can see the PCI card and the driver it is using :
Code:
[J@gx260-f10 ~]$ lspci -k
...
...
01:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
[Code]....
the PC just hangs for ever. No mouse movement, ctrl-alt-del, nothing.
I have downloaded a Linux driver from Realtek but it will not compile. I have the latest kernel-devel, headers, and gcc. I can post compiler errors if anybody would like. They're all apparently to do with missing parameters.
I am very new to linux.I have a network camera which only has an Ethernet port but no WiFi. Sadly no Ethernet port is available close to the camera.
Therefore I now bought a raspberry pi and installed raspbian to create a bridge into the wireless network, for connecting the camera to the internet.I now played around with the interface- and bridge configuration but I have problems with it.This is how my interfaces file looks like:
(The WiFi is secured with WPA2 Enterprise)
Code: Select all# interfaces(5) file used by ifup(8) and ifdown(8)
# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'
# Include files from /etc/network/interfaces.d:
source-directory /etc/network/interfaces.d
[code]....
The WiFi is connection works fine and I am in the internet using the WiFi.But I am wondering about eth0. The network parameters I specified are not the same as the parameters ifconfig tells me.Ip, Broadcast, Mask, nothing is as specified.It would be nice to give the camera a static IP that I can access it always with the same IP from the RaspberryPi.The Raspberry Pi itself gets always a new IP from the WiFi network. How do I get the camera into the internet using the existing connection of the Pi?
I've got a home firewall setup running CentOs 5.2. It's got two wired interfaces: inside and out and I'm successfully using iptables to filter and nat traffic in and out as expected. Recently I've added an AirLink101 AWLH4030 wireless nic that is recognized as the AR5212/AR5213 chipset. It appears that I have everything configured properly and I've eradicated every error encountered so far. Currently, I have my ath0 interface up and essid set but am unable to connect or even see the AP from my laptop. Here is a metric shit ton of debug/output for any networking gurus to ponder over:
Ethernet Devices:
Code:
alias lsEth='lspci -v | grep "Ethernet" -A 7'
Code:
lsEth
01:09.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 86)
Subsystem: D-Link System Inc Unknown device 1406
Flags: bus master, stepping, medium devsel, latency 64, IRQ 209
[code]...
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
I have a small intel Atom based computer that acts as a 'combo' firewall / router / server / 802.11 Access Point that services my end user needs. I'm using hostapd 0.7.0 and Fedora 12 x86_64. The system works fine on Fedora 11. I decided to upgrade to Fedora 12 last night, and completely broke my wireless. Note that configurations are _identical_ between the Fedora 11 and Fedora 12 installation. Though, I did recompile the hostapd binary under Fedora 12 libs, etc.
Anyway, Client #1 associates fine. Client #2 associates, and hostapd hangs. Strace'ing the process shows nothing... just.. dead. SIGTERM works, but hostapd is unable to 'unallocate' the wlan0 interface, which appears to be in a hung state, so I can't simply re-start hostapd. So, I have to remove wlan0 from my bridge, them rmmod ath9k, modprobe ath9k, re-add wlan0 into the bridge, restart hostapd.. But the second association consistently hangs it every time. Next, I went and downloaded the latest compat-wireless drivers as of this posting. Selected the ath9k driver, built the modules, replaced them in my /lib/modules tree, depmod'd, reboot, etc..
BIG difference. Now hostapd does not hang, and there appears to be better logging/debug than ever before. This made me happy. Unfortunately, there appears to be a new problem. Clients can now associate, but only for a split second. They are immediately disconnected, and the following message appears via hostapd's stdout logging: hostapd: wlan0: STA 00:21:5c:39:a3:99 IEEE 802.11: did not acknowledge authentication response
For every client that attempts connection. Note that I'm using WPA2-EAP-PEAP w/ MSCHAPv2. I've also, for kicks, just tried regular WPA2-PSK with similar results. I'm using a mixture of clients, Windows XP, Windows 7, Linux Ubuntu, Fedora, and others.
[Code].....
Also having this problem on Ubuntu 10.04.If I do "iwlist scan" I can pick up networks on wlan0:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
I want to set up a bridge using bridge-utils within /etc/network/interfaces like is shown here in this guide: [URL] The problem is that, at the same time, I want eth0 to have a specific static IP address. Right now I have a configuration for eth0. This guide tells me that I should not configure eth0 outside of the br0 configuration.
View 3 Replies View RelatedI'm new to this forum site and I was wondering how can I bridge a network between the eth0 and wlan0 connections?my eth0 NIC is a RealTek RTL8111B 10/100/1000 Ethernet Card (OnBoard) and my wlan0 NIC is a RealTek RTL8187B 802.11b/g WiFi USB Adapter Card.Are there any utilities, such as bridge-utils that I can use, except for Firestarter since Firestarter states that the eth0 connection is not established, or do I right-click on the network icon and select Edit Connections and go to Auto eth0 and under the IPv4 Address setting and select Shared to other computers and run a live connection there?The main reason is that I need an Internet connection for my Xbox 360, which is connected to my Linksys WRT54G 802.11b/g Wireless Router, that has DD-WRT firmware installed and 4 WiFi hotspots for any wireless device, such as my PSP, DS, DS Lite, Wii, Laptop(s), my brother's PC (needs a WiFi card), and my dad's PC (needs either a WiFi card or an Internet connection from my brother's computer to my dad's PC)
Here are my Computer Specs:
ECS nForce6m-a Motherboard
2GB DDR-800 PC6400 Memory
[code]....
I am tring to get my linksys wireless router to connect to my laptop that i recently installed Fedora 10 on. Well it is actully running of an external HD. Any way when i boot in windows it connects and works fine, but when i try to activate wlan0 it says "Cannot activate network divice wlan0!" "determining IP info failed..."
View 11 Replies View RelatedThe past couple days I've been attempting to use ndiswrapper to connect to my home network wirelessly and have run into a slight problem. I'm able to install ndiswrapper (of course), and install the driver. ndiswrapper -l comes up good, showing the driver is in place for my netgear wg311v3 card.
modprobe ndiswrapper I am able to get to work without errors, except, when i type ndiswrapper -ma it writes another file to /etc/modeprobe.d/ndiswrapper causing the deprecation error.
The card scans for networks, and I'm able type in my encryption key.
However it doesn't connect. | grep comes up with the error that the wlan0 link is not ready.
I think I've also been able to determine that the configuration I've put in to the card through the network manager is not actually configured.
Anyone know how I could possibly connect with the card.. It seems it should be able to work. alias wlano is also in place.
We need to have the wireless associated with the access point prior to the first login.
Have not been able to get it to work yet. WPA-PSK. wireless will not connect until login.
This is necessary for nfs automount and openldap auth to work. Not a home networking environment.
How to troubleshoot effectively.
I've been able to get a laptop on Fedora 14 (2.6.35.6-48) working with a Netgear WNA1100 Once up and running, I execute "ifconfig wlan0 up" from root, and everything connects just fine and is stable as long as I stay logged in. But, I haven't found how to do this automatically on boot.
I've tried to use NetworkManager, but I cannot figure out how to get the GUI to show up - it says its running and enabled in the Services gui, but I haven't figured out how to actually use it! I checked to see if the nm-applet is running with ps, and for the user login, I see:
I'm not sure if the "sm-disable" flag is my problem, or how to change it. I'm not even sure if NetworkManager will allow me to set things up for bootup, but that is the path I ran down...
I assume this is a fundamentally easy process to set this up on bootup, but I'm not stumbling across the method. I recall doing this kind of thing years ago when I was an engineer, and before I got my lobotomy to become a manager...
Can't get wlan0 working:
In networkmanager the device apears unavailable.
I use an Atheros AR922X wireless card in my router/access point and everything was working fine under maverick. Now when I try and start hostapd I get this:
Code:
root@puffin:~# hostapd -d /etc/hostapd/hostapd.conf
Configuration file: /etc/hostapd/hostapd.conf
ctrl_inerface_group=0[code]....
I have 2 NIC's in a box. One of them is external and doesn't matter for this question I don't think.
The other NIC is 192.168.100.3. It hosts an iSCSI Target and SMB Share on my LAN. It's works great.
I have another PC that has NIC at 192.168.100.101 and it hosts my DHCP (Scope: 192.168.100.5-25) server for my LAN.
I have a hardware firewall at 192.168.100.1 and it serves inet to the LAN on a different external connection.
So...
I currently have a WAP (cheap p.o.s. netgear router in WAP mode that keeps overheating). I want to eliminate the WAP device and add a WiFi NIC to the Top PC above.
So, on the first system I would have:
NIC 1: External IP and External Gateway
NIC 2: Static IP 192.168.100.3
Proposed WiFi NIC 3: Static 192.168.100.4
Question:
If I bridge NIC 2 and NIC 3 like this:
# brctl addbr br0
# brctl addif br0 eth0
# brctl addif br0 eth1
Then I simply put the WiFi in Ad Hoc, will another WiFi in Ad Hoc (for example my laptop) be able to "see" 192.168.100.101 (DHCP) & 192.168.100.1 (Gateway) (via WiFI 192.168.100.4 through the bridge to 192.168.100.3 and on to the LAN)?
Also, can the two NIC's be bridge together even though they are the SAME subnet?
I tried google but without success. I have a small home network and one computer has to work as a bridge (comp1), it connects to the internet through wlan and is connected with cable to other computer (comp2), I would like to to make that second computer member of a local network with internet access.I was trying this:
Code:
ifconfig wlan0 0.0.0.0
ifconfig eth0 0.0.0.0
brctl addbr br0
brctl addif br0 wlan0
brctl addif br0 eth0
[Code]...
Having trouble with wireless and FC11, eth0 is ok. When I try to activate wlan0 through system-config-network 1.5.97, I get msg: Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0... failed. This is a compaq laptop.
<uname -r>
2.6.29.6-213.fc11.i686.PAE #1 SMP Tue Jul 7 20:59:29 EDT 2009 i686 athlon i386 GNU/Linux
<lspci>
The wireless card is Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter
(rev 01)
I would like to mount a bunch of folders/shares when I start my machine up. I will be adding the mounts into my /etc/fstab folder BUT my WLAN0 only comes "up" and connects to my WAP AFTER logging in.
how I get it to start on PC boot instead of log in?
I think I need to disable network manager but I'm unfamiliar with the procedure in Fedora
i can't get a pppoe conection working over a wireless network,in windows I have to connect to the router first, and then put in my user and password to get connected, but i don't know how to do this on fedora, i get connected to the router through network manager, and ping is ok, but when i try to make a new xDSL connection i don't know how to make it work through the wireless network that is established and working with my router.
View 9 Replies View RelatedCode:
Commands as root works well when normal user is logged in and connected to net via KDE 4 network manager, but after logoff network is gone. And it is impossible to get it back because command mentioned above stops working!
I am having a problem trying to transfer large file (~700MB) from one station in my home to another. I have 3 PCs hooked up through a router. 1 is wired to the router and the other two are wireless. One wireless is a laptop that has a built-in Atheros wireless card that was supported during the FC13 install. The other wireless has a plug-in wireless card made by Belkin (F7D1101). I had to use ndiswrapper to get it to work on FC13.(BTW all PCs are running FC13)
The one with the Belkin card is, I think, the problem. The one with the Atheros card will transfer files at a rate of about 8MB/sec to the one with the wired ethernet connection. The one with the Belkin card will not transfer at rates over 300KB/sec to either of the other two PCs. I have tried file transfers both encrypted and not and it makes no difference.
I currently have an Atheros a5k 802.11g PCI card and I am looking to upgrade to 802.11n. Are there any cards that support the Atheros chipset (a9k) or something similar? I do have PCIe x16 available if I can go with that. Plus, I could go with an external USB 802.11n wireless adapter, but I'd rather prefer the internal card to save space. I don't mind any PCI/PCIe adapters taking up slots in my motherboard, although I might plan to upgrade to an ATX motherboard so I can have more slots available.
View 2 Replies View RelatedI run the following command on my terminal to start hostapd which sets up my router to behave like a wireless access point. $ ./hostapd -dd hostapd.conf The service starts successfully. But now i am trying to figure out a way to run this program automatically at start up so that my access point is permanently visible.
View 2 Replies View RelatedI want to connect my dataone broadband connection in bridge mode in fedora 7. As i am currently using a bridge connection through this modem (smartAX MT882) in win XP, i want a bridge connection in fedora 7 too to access the internet from linux. I have gone through some forums discussing this issue. somewhere i have found the option "adsl - setup" and tried it in my fedora 7. But it is showing the message "adsl- command not found" on this issue. I need a detail step by step procedure for brigde connection using datone in fedora 7.
View 3 Replies View RelatedI'm trying to set up a Linux box with three ethernet interfaces as a bridge where I can do some packet filtering. I don't want this box to have any IP stack, packets that are allowed through the filter should be forwarded without changes just the way a switch would do it. I have build a kernel with ethernet support but no IP stack. It detects my interfaces, and I can bring them up with the ifconfig or ip commands. But when I try to start a bridge with brctl I get this error message:
can't setup bridge control: Address family not supported by protocol
A google search for that error message gave me no results at all. The command I used was "brctl addbr br", which does work on a full installation. Does brctl require IP support in the kernel? That would be a bit odd I think, since brctl doesn't do anything IP related, everything it does is at lower layers?
Does anybody know what the above message means, and what I might have been doing wrong?
What I am trying to do: bridge 2 NICs in my linux box eth0 connects to linsys router (which in turn connects to internet) eth1 connects to Xbox 360
What I did:
Code:
ifconfig eth0 0.0.0.0
ifconfig eth1 0.0.0.0
brctl addbr br0
brctl addif eth0
brctl addif eth1
[Code]...
I'm sure this is a bridging issue and there is just some option I'm not setting correctly. Also, the reason I'm connecting the Xbox 360 directly to the linux box and not to the router is for traffic monitoring purposes. Note that all connections and functionality work perfectly when the Xbox IS connected through the router.