I have ubuntu 10.10 and I'd like to change to Fedora so I downloaded the iso image and burned it..... (To be sure, I burned the iso two times, on two cd's with two pc's) When I tried to install it it stucked before the installation begin, what should I do?
View 1 RepliesI'm not great with computers. I have no clue how to fix this kind of thing. I went into Alsamixer, and it says my card is an Intel 82801CA-ICH3. I have updated all of the files that needed updated, turned up the master volume and it still doesn't work. Somebody please explain this to me in words I can understand.
View 1 Replies View RelatedI just installer Ubuntu 10.04 Netbook Remix on my Compaq Mini 700EL, the ubuntu website says that everything works very well including the wireless. But for some reason the list of connection doesn't appear at all. It just says "device not ready" This is driving me a little nuts. It appears that the Broadcom drivers are installed. I typed lspci on the terminal and it says that the computer loads a Broadcom Corporation BCM4312 802.11b/g (rev 01)
I also downloaded the drivers even though they should be already in it. But I'm not sure.
how to fix the detection of ps2 mouse under Debian Squeeze? It is the optical mouse with wheel, red light shines, but mouse doesn't work.
View 14 Replies View RelatedI've a laptop of Compaq Presario CQ040, I installed Fedora-9 but found that there is no sound. I ran lsmod, lspci and aplay -l command and the respective output is below:
How to configure the sound card and get it working?
I have freshly installed Xubuntu on my HP compaq nx9010 laptop and grub doesn't boot system. Only minimal BASH-like line scripting is supported. How can I fix it?
View 9 Replies View RelatedSorry for repeating the same old complaint but there doesn't seem to be a common fix: Wireless does not work on my Presario R3000 although SUSE 11.x lists the hardware in the Hardware Information list and the hardware is turned on. Network Manager doesn't display any wireless networks in SUSE while Win 7 can see 4 of them on the same machine. Ubuntu has no problem either
View 1 Replies View RelatedNo wireless networking. The ethernet works fine, and the wireless interface itself works well in Windows 7 (dual boot). Tried: Ndiswrapper, notoriously quirky, does not seem to work with the XP driver (the oldest driver available for the RTL8191SE). The linux driver offered on the manufacturer's website lacks any installation instructions. I have no clue how to install a linux driver. SUSE seems to have two network managers that are constantly complaining about control: Network Manager and Yast. Neither are great and I am left missing my Ubuntu.
However, my audio only seems to work on SUSE. I have tried almost every distro on this machine. Ubuntu lacked sound and wireless, Fedora played startup sounds, but would not play an mp3 or wav file (fiddling with the mixer did not help). And Fedora also lacked wireless support. PCLinuxOS, my favorite, lacked sound and wireless. Tried some oldies too. ELE, DSL, Puppy, Ubuntu Netbook remix, Vector, Browserpuppy, Crunchbang, Cruncheee (just for experimental sakes) and probably others I am not remembering. So far, installing a free linux distro has cost me 14 dvd-R's and countless hours of installing, reformatting and reinstalling. Part of me really wanted crunchbang to work, as I love the minimalism and blacked-out theme.
I need wireless network access. The wireless light remains red in Linux and pressing the key does nothing to start the device. In Windows 7 it always lights white and works perfectly. Why hasn't SUSE adopted a gui for ndiswrapper? Other distros have it. Why is my brand new laptop, which is by no means abnormal in make or configuration, not 100% supported natively by any Linux distro? I just updated to the new kernel yesterday. So I should be running the most modern operating system available. Yet good-ol Windows 7 is my only fully functional environment.
I have a problem with installing OpenSUSE 11.3 on my server Compaq ML370 G3.4 gb memory
and 6 drives, all at 36,4Gb(scsi)On the server it is the Compaq Smart Array 532 controller.
When i install from the DVD, after i choose the default keyboard, the an error comes up, and it is restarting the installation process.When i use liveCD i can get to the desktop, but then evrything hangs.
I have tryed the SLES 11 SP1 and i think and as I recall i can perhaps manually the drivers to the installation.But my main question is, Is there a way to add the controller drivers in the installation prosess of OpenSUSE 11.3?
i've got my friend into trouble in my zeal to wean away my friend from windows. i convinced him to go for a dual boot system of XP and U 9.10. first we successfully installed XP but then got stuck when we were unable to locate the chipset driver - not even the HP website (horrible) had it ! it seemed to offer everything from modem drivers to utilities but there is no trace of the chipset / motherboard drivers. we then tried to install U 9.10 and got an error message in the middle of the installation process. it has been discussed in this forum but without any clear resolution. basically, it said the following -
Code:
[Errno 5] Input/output error This particular error is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment. btw, all along we suspected that there could be something wrong with the HDD of his computer which is Compaq Presario C 505 TU. i then tried to install U 9.10 completely on the HDD and this time got the same error message! similar problems came up when i tried installing with U 8.10 and U 9.04 we finally gave up but did run a HDD test from within the BIOS (Phoenix). The result was clear and we got the message - "SMART pass". so basically the computer is not working now because there seems to be a problem with the chipset drivers while i can't get any version of Ubuntu to install on the machine
Has anybody idea which distribution of linux shoud run on HP compaq nx 9010 without problems?
View 3 Replies View RelatedI have managed to install Arch linux on an old PIII compaq, now my question is this:
I have seen many fancy pictures of a nice Arch GUI, but all i get after install is
My guess is that it boots up in to a Shell , but how do I get to the GUI form here or have I failed from the start.
Not a guess any more Im in a shell. when i "ls" i see all the folders in "/"
I have installed Ubuntu 9.10 from a live cd, on a HP Compaq nx7010! I selected to use the entire drive, so nothing else is on there! The problem is when I start up the machine it wont boot into ubuntu! Instead I get a menu with 4 options:
Ubuntu, Linux 2.6.31-14-generic
Ubuntu, Linux 2.6.31-14-generic (Recovery mode)
Memory test (Memtest86+)
Memory test (Memtest86+, serial console 115200)
If I choose the first menu option I get the following error:
error: no such device: 07850f66-baab-4a48-B6C4-01268fee1523
Press any key to continue...
Pressing a key gets me back to the menu again! I have tried to install several times, thinking that maybe, just maybe something went wrong with the installation! But no such luck! I have also tried with different flavours such as ubuntu, xubunt and kubuntu with the same results!
I'm an absolute newbie to linux/Debian/Ubuntu. Problem: Ubuntu is loaded successfully but does not run - I just get a blank screen.
The machine specs:
HP Compaq 615
Processor AMD Athlon X2 DualCore QL-64
Processor speed 2100 MHz
ROM date 07/17/2009
ROM Revision 68GVV Ver F.04
Video Bios Revision : ATI 05/07/09
History: I downloaded Ubuntu, burnt a CD and it runs fine on my Saraha machine and it ran fine on the HO Compaq as well - from the CD. So I selected install. At the end of install when I had to reboot, the screen was filled with error messages I/O error on sector pages of the messages. Then downloaded the notebook version and again both laptops ran fine from CD. Installed Ubuntu (deleting everything else) and exactly the same problem.
After reading this forum posts I tried pressing F6 and got a screen with options. Selected them all, installed again - but same blank screen problem. Read this forum again - and found lots of posts with the same problem - on the same machine, but it appears no solutions. I'm at the point of walking away, but really would like to give open source a realistic try. I'm afraid to install Ubunto on any other machine as we may end up with nothing working.
when I try to install squeeze on my old compaq nc6000 laptop, installation will freeze at "detecting network hardware"; if I skip the networking steps, it freezes at the "detect harddisk" step.
It's the same behaviour, whether I try to install in text mode or graphic mode, expert install, normal install, whatever.
I also tried different debian ISOs. Same thing.
The screen just stays blank (a blue screen that is in text mode). When I press alt-F4 it reads:
Code:
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
That message seems to appear each time my installation freezes.
Searching the web for the message yielded known problems with the kernel vfat driver, which will not be solved. However, nobody else out there seems to have trouble getting their installs done.
So here's my question:
Can I assume this behaviour does have something to do with my windows partition?
As in: Once I have removed my windows partition on the laptop, everything will be cool?
I've been trying to install CentOS 5.5-i386 on my office notebook (Compaq Evo N610c) but the installation hangs indefinitely after booting from the disc.The exact place where the installation hangs is during this particular line
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled I tried various solutions like disabling the serial ports and installing with the necessary kernel parameters but this didn't do any good.
I just installed a fresh Ubuntu over a Vista install on a Compaq 6720s with Wubi.But the wireless doesn't work in Ubuntu. In Vista everything is still fine.I tried two tips from the help program in Ubuntu, but to no avail. I also tried reseting and restarting. Tried the manual swith on the laptop.
View 2 Replies View RelatedI have a Compaq server, as per the title, and I wish to install Ubuntu Server onto it but ran aground when I found it got to trying to run the installer after the CD Boot menu, it just stopped there, waited 180 seconds (as per the error's details) and then locked up with the Caps Lock & Scroll Lock lights on the keyboard flashing.
Now I know it's not the server, as I have installed other OSes onto it in the past, including an older version of Ubuntu server (9.04), I did try and re-install the 9.04 version but the CD I had was too scratched up and got to a point in the installer (copying files) where it just failed cos it couldn't read the disc.
The specs of the thing are:
Dual PentiumIIIs 1.4GHz
512mb RAM (keep meaning to upgrade it)
3x 18.2GB 10k SCSI HDDs (Storage)
[code]...
Not sure what else is in there, but the full specs are on the web...
i'm trying to install avira av on a compaq presario sr1103wm with lucid lynx. i've tried using the archive manager, but i end up with a package on the desktop that i don't know what to do with. i've also followed techie mo's tutorial to the best of my ability. i just seem to have come up short. below is the output of the terminal. it shows SOME promise, just not an end result.
ed@ed-desktop:~$ sudo su
[sudo] password for ed:
root@ed-desktop:/home/ed# cd Desktop
root@ed-desktop:/home/ed/Desktop# tar -xvf antivir-workstation-pers.tar.gz
antivir-workstation-pers-2.1.12-19/
[Code]...
I have been trying searching and reading for a few days now and I have had no luck getting a Encore ENLWI-G2 wireless pci adapter to install. I downloaded their Linux driver [URL]...and I keep getting errors on the makedrv (attached). I get a couple "make: *** /lib/modules/2.6.18-92.el5/build: No such file or directory. Stop. " errors but the modules appear to be there.
I have not touched Linux in 5 or 6 years, so pretty rusty. I have a call in at Encore support and will post their solution if they get to me first.
I am trying to install opensuse 11.2 on my Compaq 610 laptop, I have reformatted the hd and done a clean install of 11.2, however when I boot up the first time (before configuration) it hangs, I have tried both the X64 and the i586 distributions and the only difference is that the X64 distro boots up under failsafe mode while the i586 does not.The problem seems to be at the udev part with the hang up occurring at :
[ 6.002720] b43-pci-bridge 0000:10)00.0: PCI INT A -> Link[C136] - GSI 10 (level, low) -> IRQ 10
[ 6.096894] iTCO_wdt: Intel TCO Watchdog Imer Driver v1.05
[ 6.096159] iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
[ 6.103458] iTCO_wdt: initialized. heartbeat= 30 sec (nowayout=0)
And thereafter nothing further happens.
I tried the kernal option disablemodules=iTCO_wdt which got me to the next problem on the next line:
[ 5.761939] b43-pci-bridge 0000:10:00.0: PCI INT A -> Link[C136] -> GSI 10 (level, low) -> IRQ 10
and it now hangs here
I tried 11.1 and slackware 13 with no problems installs fine and runs fine, on the opensuse site it lists the machine as compatible with 11.2.
I'm trying to install centos 5.4 on a older compaq proliant 6500 server with raid it was previously used for windows server 2003 for several years but management wants it turned into a time clock server that will run linux, obviously there is no smart start software for centos on this model, is there some kind of driver needed, be aware that i only did installations on single drive servers and new servers that take centos right away with new raid adapters compaq raid controller 3200.
View 10 Replies View RelatedI've just got a second-hand computer at a bargain price and I would love to install Fedora 10. I have some previous knowledge on Ubuntu, so I'm not completely new to Linux, but I'm pretty amateur still. Anyway, I have some trouble installing either Fedora or Ubuntu to this machine right now. It has an AMD Sempron 3800+ (2,2 GHz) & an ATI Mobility Radeon X1250. I have the usual "Automatic boot" screen.
Then everything seems to load fine, besides I have an apciphp error. After this single line of error, I have the usual loading bar; and then a blank screen - nothing seems to happen. I saw there were some issues installing Linux on this model - so if you can help me solve this, I'm sure other people will benefit as well!
I've just loaded Fedora 13 - my 1st Linus system - on my laptop. It went smooth and connected to the net via 'eth0'. But my wireless - an EVO610c Multiport W200 lan card - is invisible to Fedora. A couple of data points are:
[root@EVO ~]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:02:A53:BE:ED
inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::202:a5ff:fec3:beed/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9758 errors:0 dropped:0 overruns:0 frame:0
TX packets:6758 errors:0 dropped:0 overruns:0 carrier:0
[Code]....
I have the NetworkManager applet 0.8.1 (2 pc screens) but don't see the "Network' icon under System->Administration I've read that should exist. I have placed the latest 'Windows' networking file from HP (sp2956.exe) into my download directory. What must I do to 'discover' my wireless card? I suspect the use of "ndiswrapper" and have imported it into Fedora. All updates have been done via 'yum'.
I can not for the life of me get the instaltion started on this computer I have made a seperate partition on the hard disk. But every time I go to install Fendora to the computer it says there is not enough disk space. Ive tired to the srink current system option and it gives me an error. Is there something in the format of the partition that is wrong? At this point I am lost. I will answer all question about the system I not sure what info you guys need. The current OS on the laptop is windows 7.
View 1 Replies View RelatedIn my compaq pressario lap, i am using fedora7, but i am not able to acess wifi.
View 1 Replies View RelatedThis post is for an HP parallel printer but I think it should work for at least "some" other parallel printers.I am sure that someone smarter than me will follow up this post with a "well, just do this and that" and you will have your HP Laserjet 6P printer ready to go, but since questions litter the forums of MANY distros on how to get "at least" an HP parallel printer to work, I'll post this anyway.This may or may not work for you if you do not have an HP but you can try it.The install printer box will let you do an install for an HP Parallel and it asks for how it is to talk to it, through CUPS sock or "local host'. When we get through what I recommend you should chose "local host".
View 2 Replies View RelatedI made a clean install of Ubunto 10.10 on my Compaq Presarion F700, nVida graphics, AMD Turion 64x2.Installation was fine.When I boot, it takes a lot of time, 5 minutes or more.Also, after the system loads I get those applet errors I've attached. Sometimes I get all the applet errors and sometimes it get few of them.I tried several configs of "GRUB_CMDLINE_LINUX_DEFAULT" but still no luck.
View 2 Replies View RelatedI have two displays: my main being an Apple Cinema Display (1920x1200), and my secondary being a Compaq W17q (1440x900). Previously all applications saw the secondary fine, being able to detect its name, native resolution, refresh rate, and so forth. But today, for no reason, after going into nvidia-settings the display is now being called "CRT-0" with only 4:3 resolutions available (1024x768 being the highest).
So now I'm stuck with the wrong resolution on my second monitor. All I can guess is that something more integral in Fedora is no longer able to read the EDID in it or something (I say integral as it's not just nvidia-settings, its everything, not to mention my install of Win 7 still reads the display A-OK)? Maybe I could just force the 1440x900 resolution? If so, how? Everything I've tried so far has either had no effect or resulted in glitch city.
I'm new to Fedora, I used to have Ubuntu 10 and found that some software I required would not work properly so I decided to Fedora under recommendation from a friend. I really like it but when I installed Fedora 13 on my Netbook I found it difficult to set up my wireless connection.
View 6 Replies View Related