General :: External Monitor Image Not Centered In The Screen?
May 4, 2010
I'm using Xorg 7.5 on a Radeon HD4870 with the FOSS radeonhd server on my HP 6830s. The laptop has a VGA connector and I attach it to a 37" panasonic plasma TV. It works fine except for a little annoyance: when activated, the TV screen is set to the resolution of 1360x768 (which it reports as being the highest it supports) but all the image is shifted by about 100 pixels to the right. I can't see the leftmost part of the page, and I have a black vertical bar to the right.
If I change the resolution to 1024x768 there is no shifting, the image fills the entire screen with no parts hidden, but at this resolution the image is stretched. How can I tune the position on the external monitor so that the image is centered in the screen filling it entirely?
View 2 Replies
ADVERTISEMENT
May 10, 2011
I have an HP Pavilion dv9000 which I would like to use completely with any Linux OS. I have tried to install Linux Ubuntu 10.04.1 but it appears that it doesn't recognize the external monitor and ends the installation. I have a clean hard drive that I could install but I do not know which of the two drives I should replace. I can only get into windows in safe mode and I would think this may have something to do with the problem, don't no.
View 2 Replies
View Related
Aug 7, 2011
I am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again.
When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have a Thinkpad E420, Fedora 15
View 14 Replies
View Related
Aug 28, 2009
I installed FC11 on my laptop T43 and the video card is ATI Mobility Radeon x300. Now I have a problem of screen resolution with external monitor:
When I do presentation, I have to mirror the two monitors and both set to 1024*768, which is not perfect.
I remember that when I use RHEL 5 desktop edition, The system can automatically detect the external monitor and set it by itself ----- The laptop uses 1400*1050 and the external monitors such as projector uses 1024*768. But I haven't found such feature on FC11.
View 9 Replies
View Related
Feb 21, 2010
I am running Ubuntu 8.04 on a laptop. I have a 19" Acer monitor and in the past have successfully configured my xorg.conf to handle dual monitor setup with 1024x768 on the laptop and 1600x900 on the Acer monitor. What I have done now is run the laptop through a KVM switch. Due to this, I would like to set the Acer monitor as the primary monitor and just shut the laptop. How can I project my laptop screen to my Acer monitor so that I can use the 1600x900 resolution available rather than just cloning my laptop and using 1024x768?
View 1 Replies
View Related
Jul 3, 2010
The laptop is a samsung X30 and i spent days trying to install ubuntu 10.04 unsuccesfully as there was no clear picture on the screen, just a black and purple splodge. I then saw a post on these forums discussing the default resolution of ubuntu and how it is incompatible with some machines so via VGA cable i connected it to my TV and sure enough i could see what was going on and finished the installation process. I assumed that once ubuntu was fully installed i would be able to change the resolution using the monitor preferences but none of them worked. I am now faced with the problem that unless plugged into the TV i have no picture on my laptop, does anyone know why my laptop screen wont work with ubuntu and how
View 2 Replies
View Related
Sep 14, 2010
The monitor on my laptop has become a bit sketchy and money is tight at the moment. I am currently connected to an Acer flat screen monitor. I have the ubuntu settings for using only the external monitor. This works fine once I"m in Ubuntu. Is there any way to force the display to the external monitor prior to ubuntu starting? This may or may not be a linux-related question. It was be very helpful if I could see my Grub menu on the external screen. I could not find any setting in my bios. The keyboard shortcut sometimes works but not on the grub menu.
Ubuntu Lucid
Dell Precision M20 laptop
ATI video card
Dual boot with XP Pro.
View 1 Replies
View Related
Mar 28, 2016
I am running Debian 8.3, and I'm running Gnome 3.14.1.I have an external monitor plugged in with HDMI, and while Linux is loading both screens are on duplicate. Once the GUI kicks in, only the external screen works, so I have to enter my password blindly. Then, I open a terminal and run
Code: Select allsudo echo 950 > /sys/class/backlight/intel_backlight/brightness
and the laptop screen turns back on.
I'm wondering: Is there a way to streamline this so that it happens on boot, but after GNOME loads?Or: Is there a better method to solve this?
View 1 Replies
View Related
Jul 2, 2010
I'm a new user and recently installed ubuntu on an old samsung laptop, during the installation process i couldnt see anything on the screen and came to the conclusion that ubuntu's default resolution was different to that of the laptop screen so i plugged it into my TV and sure enough it worked however i still only have a picture on the tv, ive tried all the resolutions available in the 'monitors' box but nothing, does anyone know how to fix this?
View 1 Replies
View Related
Feb 19, 2010
I'm using dual-screen output with KDE 4.4 on my laptop. Is it possible to have the KDE panel on the external monitor if attached and back on the laptop's LCD panel as soon as the monitor is disconnected?
It seems that Plasma prefers the built-in LCD even if an external monitor is connected. I tried various settings with xrandr and also in the System Settings but none of them helped. The only way to move the KDE panel to the external screen is to disable the built-in LCD.
What I would basically like to do is to use the external monitor as primary in the office and the laptop LCD next to it as a second screen. When I'm traveling I'd like to use only the laptop LCD.
Is there also a nice way to switch between the screens? On the Internet I found a script for the "screen switch" key for IBM Thinkpad and modified it to work on my Dell. But it would be nice to have this also automatic: autodetect the monitor attachment/removal and perform a configured action. The KRandr doesn't seem to have such a feature. Is there anything I could use?
My system is: Kubuntu 9.10 with KDE 4.4 upgrade. Hardware: Dell Inspiron 1545 with Intel GM45 card.
View 3 Replies
View Related
Apr 3, 2011
Just did a fresh install of Natty B1 (previously had alpha 2).. I noticed this issue w/ A2, as well.. plugging in the exterminal monitor (via mini-displayport-to-vga connector) will do the following:
1) turn the screen on the laptop's display entirely black (but not turn it off).. i can move and see the mouse cursor.. but everything on the window appears to not rending or "painted" black..
2) external monitor never becomes active..
the only way to recover is to kill/restart X or reboot after disconnecting the extmon.. having extmon plugged in from boot produces the same results (and it doesn't seem to ever become active during boot up). sometimes this won't happen right away if i plug in the external monitor.. but opening the Monitors system prefs dialog will definitely cause (or detect displays) ,etc I waited to see if the issue would fix itself w/ the beta update, but it hasn't.. Any other 8,1 owners out there that can verify this issue? My (totally uninformed) guess is that it's due to differences in the display/gfx hardware and thunderbolt integration(?)
(I've seen a verification verifications of working-out-of-the-box.. but they were from 8,2 and 8,3 owners (which have discrete graphics cards))... If anyone's gotten this to work with some config stuff, I'd love to see that as well (since the wiki page for 8,1 says it works ootb). If someone could let me know where I should look to capture error output when the above issue occurs, that would be awesome.
View 4 Replies
View Related
Sep 22, 2010
I have a mac book pro 5,3 with the nvidia gforce 9600m. After getting Ubuntu installed as a dual boot, I wish to use an external monitor while using Ubuntu. (it doesn't have the problem with OS-X) The external monitor is a samsung syncmaster 192 n. when I connect the other monitor and press 'detect display' both go grey creens(the external already is of course). My lapton screen will not recover until restart either. I need this monitor to run a numerical mesh 3d mesh creator that will not fit on my screen alone. Wouldnt be a problem if the creators were software engineers but the program window cannot rescale, and is beyond the resolution capabilities of my 15'' screen alone.
View 1 Replies
View Related
Apr 13, 2011
When my netbook has an extended screen, using an external monitor, all of the panels stay on the netbook, not the big monitor. When I connect an external monitor, I want to use it as my primary screen. I only really intend to use the netbook screen for skype calls (so I am looking into the webcam, and not away from it) since it is so small. I wish the secondary screen to be the netbook, not the external monitor. How can I do this?
View 1 Replies
View Related
Jan 16, 2010
I have an Asus z9100 laptop with an Intel 855GM integrated graphics chip, which is running Karmic (the purpose of the laptop is to be a MythTV frontend so my understanding is that it needs to run 9.x in order to connect to the MythTV 0.22 backend - I have installed and configured this using the installable Mythbuntu package) and the laptop is subject to this bug which causes random freezes:
[URL]
So, following advice for similar freezes I've seen, I have added the following options to my grub menu.lst on the kernel line:
nolapic nomodeset
and I have edited xorg.conf so that it makes use of the vesa driver instead of the Intel driver. This results in no freezes and if I wanted to watch Myth on the laptop screen I'd be squared away. However, the laptop has a damaged screen so the point was always to output the signal to an external monitor via its VGA out.
When I attach the external monitor and boot with the setup as described, the external monitor is never detected. But I noticed that if I remove the "nolapic nomodeset" from the kernel boot line, it is detected. However, signal is only output to it during the earliest part of boot (when the Ubuntu logo is in the center of the screen before the full-screen graphic with the animated progress line), after which the external monitor goes black and all the display output goes to the laptop screen. The external monitor power button is still lit up green as if it has been detected and is receiving signal, but it's just a black screen.
get the signal out to the external monitor after the initial part of the boot process, using the vesa driver? Here is the current state of my xorg.conf:
Code:
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
[Code].....
View 2 Replies
View Related
Jan 2, 2010
I have a netbook (Acer Aspire One) I'm running Slackware 13. and usually, I prefer to connect an external monitor. When I switch my machine on with the monitor connected, the display is duplicated on both screens and since I just want the netbook's screen to be off and only see the display on the external monitor, I can doxrandr --output LVDS --off
Great! However, it's a hassle to do this every time I log in and I'd like to automate the process if possible. I did some googling and I found that if you want to automate xrandr commands, you can put a script in /etc/X11/Xsession.d/ (see this). I wrote the following script to automate my xrandr commands and since the Xsession.d directory didn't exist, I tried creating it. The script was called 45custom-xrandr_settings, as the one on the RandR wiki is called the same.
Code:
#!/bin/bash
# Check whether the external monitor is connected
[code]...
View 5 Replies
View Related
Sep 24, 2010
I have Ubuntu (running Jolicloud) on my HP dv2000 laptop, connected to my Sony AV Receiver through HDMI to use the TV as an external monitor. However, the resolution seems to be slightly off as the outer edges of the screen are cut off. Is there a way to fix this by editing the xorg.conf file? My current setup is below. I tried adding the line "Virtual 1244 700" to the subsection "display", but when I restarted it threw me into low graphics mode. Is there anything else I can try?
I also tried setting up the resolution at 1920x1080 on the TV and kept the default resolution on the monitor as 1280x800, and as you would expect displays the entire desktop in a smaller version on part of the tv. However, the desktop is still offset, leaving the top and left margins cut off. So, perhaps I need a way to offset the screen? Is this possible in xorg.conf?
View 8 Replies
View Related
Oct 16, 2010
I've installed Ubuntu 10.10 on my Macbook Pro 5,5. Everything is running fine with some tweaks. Just one thing bothers me: when I tell Nvidia X Server Settings that I want to use my external screen as primary screen it doesn't put the gnome panels to the other screen, well... sometimes it does after a couple times but most of the time it doesn't.is there a way to automatically detect when I connect a monitor instead of going to the Nvidia settings? Just the way Mac OS X does?
View 1 Replies
View Related
Mar 20, 2010
I am having problems with the refresh rate if the screen. In the refresh mode of the monitor in the monitor options have only one option 60Hz. I have LG 24 + ATI Radon 3870, and have already installed the ATI driver via Ubuntu download center.
View 1 Replies
View Related
Nov 2, 2010
I have a pc I want to clone and it has 2 partitions sda1 which is vfat and sda2 ntfs. When I had mounted my external hdd it was seen as sdc1 and my Knoppix boot as sdb1. I tried using the following command to copy the pc image to my external but when it gets to 26Gb it gives read error.
mkdir -p mybackup
mount -t ntfs -o rw /dev/sdc1 ./mybackup
dd if=/dev/sda of=./mybackup/780.iso bs=4096 conv=notrunc,noerror
Where am I going wrong? Is there anything wrong with my above commands?
View 3 Replies
View Related
Aug 11, 2011
I have an external monitor connected to my laptop (extended display). I always drag the Totem player from the laptop screen to external monitor to watch video files. I wonder, if the Totem player can be set to open in the external monitor automatically, everytime I open it?
View 1 Replies
View Related
Aug 17, 2011
My software and hardware information are as follows. I have Fedora 12 and KDE 4.4.5 installed on a Dell Vostro 1500 laptop. I believe it's a 64 bit processor; it's an Intel Core 2 Duo CPU. The external monitor is a Dell as well.
My problem is that my system does not seem to be detecting an external monitor that I have connected. Everything else is working just fine; however, I would like to have the option of attaching an external monitor. When I plug the external monitor into the laptop, the external monitor remains black and appears to be in power save mode. The results of xrandr -q (with or without the external monitor attached: it doesn't appear to change) are as follows.
Code:
How can I get my laptop to recognize that the external monitor is even connected? Let me know if I can be more specific or provide additional details.
View 5 Replies
View Related
Sep 22, 2010
I recently installed Debian, using the amd64 Network Install .iso. I'm using XFCE4 as my desktop environment, and everything is working well... on my laptop's screen.
My desired setup is to have my laptop sitting on a well-ventilated shelf, closed, and to have an external monitor be my main monitor. I want this because I'm using my laptop as my "home" computer, so it never moves, and I don't like the keyboard/trackpad. My laptop has a VGA output, and I can get my desired setup on my Windows partition (not stating a preference ; just that the hardware CAN do what I want it to).
I've been working my way around the Internet for a few days, now, and I've got the commercial NVIDIA driver installed. If I run sudo nvidia-config --twinview I can get my external monitor to be part of the display, which is great, but it's part of a dual-screen monitor setup, which is not what I want at all, because (a) XFCE's multiple virtual desktops are good enough for me and (b) my graphics card is integrated, and I'm trying to squeeze every drop of performance out of my laptop that I can (1 gig of RAM; the less that my graphics card eats into it, the better). Plus, it'd be annoying to accidentally drop something on my laptop's screen, and then have to dig it out of the shelf in order to undo it. I'm not saying that I'm consistently clumsy, but I'd eventually end up doing it.
View 2 Replies
View Related
Dec 25, 2010
I've got an eeePC with a really tiny monitor, so whenever I go (home, faculty, parent's home, friend's home, ...) I attach it to any external monitor I can find.
If it matters my system is like this:
Archlinux
Linux 2.6.36
Xorg 7.6
X server 1.9.2
Intel Corporation Mobile 945GME Express Integrated Graphics Controller (fully accelerated by intel modules)
When I boot up the system, it uses the integrated monitor (LVDS1) only, and I have to manually manually switch to the external monitor (VGA1) using xrandr.
Is it possible to configure my Xorg (or whatever) so that it uses the VGA1 output if present?
View 1 Replies
View Related
Aug 8, 2011
Does anyone know what program I can use to set it up so when I plug in a VGA or HDMI monitor it automatically sets up video output?-P.S. -This is on a ArchLinux install with PekWM for the window manager
View 5 Replies
View Related
Feb 27, 2010
I have a Lenovo 3000 N100 laptop which LCD does not work anymore.So I borrowed a monitor from my friend and started using it(it has been few days).I had installed Fedora-12 few months ago. After connecting the external monitor, I found that this one shows good graphical start-up but just upto the login screen(just before the login screen, login-screen does not come) and it proceeds no more.Though I can get the virtual consoles restarting xserver is of no use.
View 5 Replies
View Related
Oct 15, 2010
A few days ago I installed browserlinux onto my AspireOne netbook whilst connected to a 15" external monitor of 1024x768 at 60Hz. During installation I ran the Puppy Xorg Wizard with the netbook's monitor (1024x600) switched off. It selected the optimum resolution of my external monitor correctly as 1024x768 and the 'intel' driver for the Intel 945 Express chipset. However when I ran programs and maximised their windows they would cut off about a third from the bottom. I ran the Xorg Resolution Wizard which showed a resolution of 1024x600 despite xorg.conf only showing an option of 1024x768. I tried to copy a xorg.conf from Linpus (Fedora 8) which had required some altering in the past to run the external monitor at the correct resolution but X failed to start (possibly because Xorg in browserlinux is a newer release). Would it be possible for someone to upload a xorg.conf file which would enable display the external monitor at the correct resolution (and ideally allow switching between the two monitors - under Linpus the hotkey is Fn + 4) or suggest alterations to the current file?
[Code]...
View 7 Replies
View Related
May 2, 2011
How can I detect when an external monitor is connected in linux? I need to run various scripts to set up my workspace. Is there some clever way to kick off a script when the monitor state has changed? I'm using the Nvidia display driver.
View 3 Replies
View Related
Jan 28, 2010
I have an Acer Aspire One AO150 and am having trouble plugging in an external monitor under Ubuntu 9.10. There were no problems under 9.04. If I plug in an external monitor once the machine is already up, then bring up the 'display' application to activate it, it basically hangs. There are no problem under these circumstances if I have desktop effects turned off.
A few more details after a question below. The machine does not respond to its keyboard commands to switch to an external monitor, nor does it respond to Ctrl-Alt-F1, etc to switch out of X. The pointer is visible on the monitors (at the edge of each) and is frozen as a 'busy' cursor, but with no animation. The kernel does respond to SysReq commands (REISUB).
In the latest attempt I had the external monitor active earlier, then removed it and activated desktop effects. Upon plugging in the eternal monitor then bringing up the display application, it hangs.
View 3 Replies
View Related
Nov 17, 2010
I connected an external 22" monitor to my new linux netbook and now I am trying to improve the display clarity. By shifting the "clock" monitor bar to 100 ,the letters were less faded but edges of my screen were lost (by zooming in). Can I fix that through Linux?
View 3 Replies
View Related
Jun 11, 2010
I've got a laptop running Backtrack4 and an external tv/monitor. Is there a program/command/configuration file that I can use to allow my laptop and monitor to connect with one another via HDMI?
View 1 Replies
View Related
