Fedora X86/64bit :: Going Loopy - Nvidia Driver And DVI - Login Screen Went Black
Dec 24, 2009
I had a fully working Nvidia driver setup in FC 12 with no problems using an old LG monitor (LCD panel) on a VGA connection. I have just replaced the monitor with a newer Dell model that has a DVI connection. I plugged it in and got nice Post Screen, FC 12 boot progress display but when it got to displaying the login screen it went black.
Ctrl +Alt+F2 took me to a command prompt where I can type commands no problem. If I change the driver to the Nouveau (and Chattr +a the xorg.conf file) I get a lovely gui. So far nothing I have tried has let me use the Nvidia driver. I have searched around Google and tried nvidia-xconfig, system-config-display, livna-config-display xrandr (which fails to work at all) but so far I have got no where.
NVidia FX5200: nvidia-glx-173xxx The problem is that, when I install it, upon rebooting, I get a black screen with one blinking underscore at the top left corner. I somehow managed to get into the console and .. there's something wrong with the video card driver ( no way I could catch it into a picture ).
This was the exact reason why my Fedora CD was laying on the corner for months - I remember having this issue earlier as well.
Is there a way to fix it or at least, recover from a broken video card driver ?
I`m using a N5010 dell laptop with an Ati Radeon mobility 5650, I tried to install the ati drivers on F14 which caused a black login screen and there is no way to open the console and do anything. On top of that I`m using Ubuntus Grub2 so I`m practically stuck.
I have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
I'm trying to install OpenSuse 11.2 64bit on a new Dell Latitude E6410 notebook. This is the Intel i7 processor with 8 Gb of RAM and Nvidia NVS 3100M graphics. I can boot from my 64bit installer DVD, but once I choose either Live version, to test it out, or just go for Install, after the first selection screen where I can change the default video at the bottom, I just get a black screen, no video.
I can't find any info on installing Suse on this notebook, (I think its only be available for a couple of weeks now). What do I do to get the screen to show me the graphical installer, Or how do I make the KDE Live version run from the 64bit DVD. I also tried the 32bit version DVD, but it wouldn't give graphics either, so it seems like an X issue.
After installing Ubuntu and seeing my resolution would only go to 800 x 600, I found this strange. A message popped up about the nVidia drivers I could downlaod that would enable me to do more so I did. I restarted and all was fine. Nice effects, high resolution. However, after going on XP, then going onto Ubuntu, the screen ahs gone black. The white Ubuntu logo can be seen for a while as it loads, but then the monitor goes completely blank as I hear the sound when the log-in screen appears.As I said in my title, it was the 185 driver
I've been using ubuntu fine for a while when I decide to activate my nvidia graphics card.After rebooting, however, I hit nothing but a black screen. I've searched the nets and others have seemed to solve the problem after hitting alt+ctrl+f1/f2 and editing some files after that, but that doesn't work for me. Booting into recover console gives me nothing but a long stream of white words before it runs to --> done. and then it goes back to a black screen. Running from Live CD I can't access my ubuntu files.
Previously running Squeeze I was using the proprietary driver and never had any issues. Now using the nouveau driver video playback of mp4 files is glitchy and programs like google earth don't operate smoothly. I installed the nvidia driver from the repositories based on this guide, used nvidia-xconfig to generate an xorg.config file. I made sure noeveau was blacklisted and rebooted my machine.
I was greeted with a black screen. So I booted up in recovery mode, used telinit 2 (side note: what happened to /etc/inittab???) to change to a runlevel that doesn't start X, and confirmed that nouveau was, in fact, not loaded. Typed startx and without any errors or warnings the screen went black. ctrl+alt+fN wouldn't bring me back to a terminal, but hitting the power button did shut down X and halt the machine.
I'm not really sure how to go about debugging this as I get no useful output from anything, just a blank screen and that's it.
For the time being I just blacklisted the nvidia driver and let the system boot with nouveau; I'd still like to get the nvidia driver working properly, though. I've always just downloaded the driver right from nvidia and installed it, but I know that isn't the best way to do it. I'd rather not screw up a brand new system, it's so nice and fast with the new SSD.
I just installed Maverick on my HP tx1000. Jockey offered me two drivers for my NVidia Go 6150. I tried the recommended one--and it seemed to be working. It had a green light next to it in Jockey, Compiz worked, etc. Then I rebooted.
Except it didn't reboot--the disk thrashed for a while, and then I was met with a black screen. I tried recovery mode and got a bash prompt...which crashed when I ran `startx'. Then I tried Failsafe X, which did work. After some experimentation, I realized it was the Nvidia driver at fault, so I tried the not-recommended one, which didn't work, and now I've disabled both of them. But isn't there a proper driver for me to use? IIRC, I was using a restricted one with Lucid, and it was working all right.
Fun fact: The day before I installed Maverick, Windows 7 randomly decided to not boot all the way. It would show the splash screen, and then hang with a black screen too. But it works in Safe Mode. And had been working fine for a while beforehand. There must be demons in my graphics card.
I was messing around with the screen orientation and thought it would be funny to orient it sideways. Big mistake The screen went black.I can force a shutdown, login and I get the same black screen. I tried hooking up an external monitor and the monitor showed no input so I'm guessing my laptop doesn't have that capability with Fedora.This is my main computer.
I realize that many have had the issue of getting a black screen when booting up. I'm posting because I've tried a couple fixes that I read after doing a search and haven't had any luck yet. I have the 64-bit 10.04 installed on my netbook and my issue surfaced after installing the current nVidia accelerated graphics driver. Following the install ubuntu now boots to a black screen and nothing more. 'nomodeset' only allows me to boot ubuntu in low-graphics mode (which I'm in now) and this fix hasn't produced a solution either: [URL]..64&postcount=9 My netbook has nVidia ION2 graphics with an integrated as well as a discreet graphics card (Intel GMA3150 and NVIDIA GT21
I have an problem with login in to a fresh installed Ubuntu with the nvidia drivers (graphics card nvidia 210). So far I have installed Ubuntu 10.04, Ubuntu 10.10 and Unbuntu 11.04, they all seem to have the same problem. when I log in the screen goes black and the pc's hangs. I can switch to a terminal before I login and everything seems operational. I can login to Ubuntu with a fail save x session.
After installing debian squeeze I tried installing a nvidia driver. I had to type: /etc/init.d/gdm3 stop The nvidia driver wouldn't install because the 'make' command was missing in a path or something. Now I cannot get the GUI anymore. startx gives me a blank screen rebooting the computer gives me a blank screen. I can only boot in recovery mode. but the nic doesnt work so no internet connection.
The problem come after i kill the Xorg using the kill command,and the screen turns to black without anything so that i can do nothing. The problem goes on after reboot
I've installed Fedora 15 64bit version yesterday, first time using Fedora ever, I like it so far, but there's one thing that's bugging me. It's the flashplayer. I'm using 64bit version of adobe flash player called "Square", which work's fine for ....., but when i try to switch to full screen on site warcraftmovies(they're using player Minoto i believe) it's working strange. If I open a new Firefox and I haven't played any other video from ..... for instance, it works fine and switches to full screen no problem, but If i exit full screen and try to switch to full screen again, it will give me only black screen. If i click on the window border of firefox the video comes up again, but not maximized, only normal window. I tried running firefox from terminal to see erorrs and whenever i try to maximize the player it gives me this error
I used to have FC11 installed with the nvidia supplied binary driver. Worked fine, very stable. Trying FC12 and FC13 live CDs caused a hang, so I stuck with FC11. FC14 live CD did boot so I backed up my own files and did a clean FC14 install. Upgraded to get kernel 2.6.35.6-48, installed the nvidia driver from RPMFusion (260.19.21) and had a working system! Now, after a cold boot, the kernel always hangs during boot. Tried a number of kernel boot option (apci=off, noapic and a few others too). The hang is not always at the same place. The earliest it has hung is after:Disabling lock debugging due to kernel taint
Sometimes its a few lines later at:NVRM: loading NVIDIA UNIX x86_64 Kernel Module 260.19.12 ...(which would seem to imply that the hang can even occur a step or two before the actual driver is loaded!)
Sometimes it keeps going for a few more seconds and randomly hangs during some other driver load.
Without a specific nvidia driver the system always boots ok, so I'm pretty sure its the nvidia driver but I just can't seem to get a handle on this in a reproducible way. Sometimes, when I have make some other change, it will boot and work ok, but a reboot locks it up again (for example, in case it was SELinux, I disabled it and on the next reboot it booted and worked ok. Then, next boot, it wasn't working again). When I make changes, I reboot using the previous kernel, make the changes and reboot, with an occasional success. Once I start rebooting using the latest kernel, it always hangs.
I'd love to get a solution to this, but even some advice on debugging this would be appreciated!
I'm using 8600GT, 256Mb, PCIe card in a MA69VM motherboard with 3Gb of RAM.
This problem started within the last few minutes. I run a program in my browser that uploads data from my machine (ubuntu) to another machine (Fedora 13), for manipulation and then spits back the data that does not match our standardised information.
When I tried to run it a few minutes ago, it seemed to take a long time to make the connection. I went back and checked the machine, everything was connected and fine. I decided to reboot the machine from within KDE and then try again. Same result. I went to the machine again and tried to login through KDE, the screen goes black for a few seconds and then returns me to the login screen. I switched over to a virtual terminal and was able to login using the same credentials. I checked the .xsessions-errors file and this is what I am seeing:
I just did an update of my Fedora 11 machine, and it required a restart. After restart it will not try to boot up or even show a splash screen. The only thing I see is a black screen with a flashing white cursor.Any ideas on what I can check so I can boot up into Linux again.
My last setup (years ago) ran fluxbox so because it was familiar I installed it as a secondary to xfce right off the bat. I download a lot of different stuff because I like to try out all the apps I can find but somewhere I broke something. I can still run fluxbox fine, but nither the Xubuntu nor Xfce sessions will run now. Last thing I remember changing was pulse audio(removed it for an experiment I was trying with jack audio), not sure if it is connected but when I try to login to xfce the screen goes black, flickers a few times then it brings me back to the login screen.
I tried failsafe but everytime I do my monitor gives me a "frequency out of range" error. I tried purging and reinstalling xubuntu desktop and xfce settings but I am thinking its my xorg config. My laptop is a Toshiba satellite M305D-s4830 with ATI Radeon 3100 mobile graphics card and I am running Xubuntu 10.10. Unfortunately I also broke the screen, so right now I am stuck with an external monitor till I get a new one.
With my first kernel, that comes with Fedora 10 x86_64 installation DVD, I can use ctrl + alt + f2 from desktop, switch to terminal, and log in to any user.
The problem is: Eventhough the login screen appears as usual with kernels 2.6.27.21-170.2.56.fc10.x86_64 and 2.6.27.24-170.2.68.fc10.x86_64, I can not login. When I enter username and password, the screen refreshes itself to its initial state, i.e., like when i hit ctrl + alt + f2 from desktop. I also tried ctrl + alt + f3, f4, f5 etc nothing changes. Also, I want to remind you that I can login from desktop terminal successfully.
Issue: Black screen displays after nVidia splashscreen.
History: I performed a clean install of Fedora 12. I performed NVidia driver "GEForce 4 and below" install for a PAE kernel as found here:[URL]..I kept a log of each command in the order performed:
[Code]...
Well, I just got back from the Pepsi Center after watching the Denver Nuggets NBA basketball team look silly against the Dallas Mavericks. 4.5 hours later and I still have a black screen. Was it Einstein who said, "it is insanity to do the same thing, the same way, over and over and expect a different result"? I feel I will been testing that hypothesis soon.
I am running Fedora 10 on a Gateway Machine. I tried to install the corresponding drivers for acceleration but it seems to have broken the display. After the loading splash screen, the screen goes black and does not respond to anything. I did manage to see the Grub boot loader by pressing 3 a number of times while booting the machine. Any ideas for how to revert the computer to its normal display so i can try again at getting these drivers working. It is a tad bit annoying not having a display but hell, this distro is already as far as I can see 10x as good as Ubuntu.
I installed some weeks ago Fedora 14 via burnt iso file downloaded from official Fedora site. It was working perfectly like a charm for me until yesterday when I tried to install zend server for PHP.During my first try of installation of zend server it corrupted out my apache server and I lost apache on http://localhost.I removed all "zend-server" like stuff from "Add Remove Software" screen.
Installed again apache 2 in the form of LAMP (Linux Apache Mysql Php)via terminal. Apache installed correctly and started workeing again ok on localhost.n again I tried to install zend server from install.sh file in downloaded zend server installation. It showed me after a while like "zend server installed successfully".I shut down my pc thinking everything is ok now.
Today when I started my system, it shows me boot screen of Fedora, I select fedora and then it shows me baloon filling up for around 5-7 secs. Then all of a sudden a black screen appears up with a cursor blinking at its top left and then nothing else happens further. I cannot find login screen to my desktop anymore.I remember one thing thating reinstallation of apache from terminal, I set following command like "chkconfig --level 235 httpd" (I guess that's what I have written as per some online tutorial for LAMP). Is that cause of mine problem ot its something else?
So, I just installed Fedora yesterday. I have been trying out different Linux distros and Fedora was next after Ubuntu and SuSE failed severely. So, I installed F14 yesterday and everything has been great... until I tried to set my JAVA_HOME variable. I followed the instructions here.
After editing $ vi ~/.bash_profile as the site instructs, I proceeded to log-out and log back in...except I can't log back in. I have repeatedly gotten the login screen, selected my account, and entered my password. When I enter my password incorrectly, it says 'Validation Error' and that is not what is occurring. The display goes black for a couple of seconds and I am redirected back to the log in screen.
So I installed the Nvidia driver on a fresh install of F13 & rebooted in the image I've attached. So, my question, what should I be posting here to fix it? Xorg.conf? Honestly, the one thing I've never had an issue with in Linux is video drivers. I've always run Nvidia cards & they've always just worked. So I'm at a loss for the first time in a long time. I also tried googling, but I have no idea what to google.
Running 2.6.33.3-85.fc13.i686 and just purchased a AGP 7600GT 512 video card. Searched around and found:I did the rpm, yum, sed, mv & dracut as directed. Then I rebooted. When it starts up (all the normal bios messages) and then I 1/2" bar across the bottom of the screen with Fedora 13 on the right end and .... nothing. Just sits there. I've used my Live-13 disk and tried to reverse the procedure but I'm starting to think it's the video drivers.
Although I managed fairly quickly to get 3D enabled on the GF 7600GS of my desktop, it took me longer to get 3D up on the GF 9650M GT of my Asus laptop M70Vn. Although I made extensive use of the numerous procedures outlined here, none of them worked and booting my laptop always ended up with me facing a jet-black screen and a completely inexpressive blinking white cursor. My solution was simple: I did not blacklist Nouveau and problems mysteriously disappeared.
I have a Nvidia 275GTX and I installed the nvidia drivers via RPM fusion and blacklisted Nouveau as instructed by a guide online that I see matches the one on these forums. When my system boots up now instead of having the cool blue screen with the fedora logo in the middle that loads up I get a black screen with a bar at the bottom that says Fedora 15 to the right and the bar fills up blue and white. It looks like 8 bit Nintendo. Did I do something wrong? Is there a way to get the nice Fedora 15 load screen back?
I just installed the 10.7 drivers (no workaround they just installed). And now after boot i get a black screen. I have a Radeon HD 4850 there is a way to fix this without reinstalling the OS. Ok in recovery mode when I type Startx i get: line 143: /usr/bin/mcookie: no such file or directory Couldn't create cookie Then if i type Xorg -configure i get : Fatal server error: Cannot open log file "/var/log/Xorg.0.log" Please consult the fedora project support.
