I have been getting internet thru the NetworkManager service in FC12. Suddenly today it refused to connect. I tried turning the service on and off, made sure logon info was correct, no luck. Finally I just turned it off and turned on Network service, and that worked. Is there some kind of bug in NetworkManager these days?
View 2 RepliesI had been running Fedora 12 for some time without much difficulty until I had to change the motherboard of the computer. The new MB comes with Realtek 8112L PCIe Gigabit LAN controller.I am not able to use this LAN controller without Network Manager. The problem is I am not able to set a static local IP with it. Network Manager -> Edit Connections -> Auto eth2 -> edit -> IPV settingsAs soon as I change Method to Manual, 'Apply' button gets grayed out.I am not able to save any change.
View 5 Replies View RelatedI am running Fedora 13 and using Ndiswrapper with my pci wireless card. my router is a netgear wgr614v9 wireless router with wpa2-psk. When I try to connect to my network the only options I see for security are dynamic WEP (802.1x) and WPA &WPA2 Enterprise and for authentication all I see is TLS LEAP Tunneled TLS and Protected EAP (PEAP). I can connect to my network when I drop security on the network but other wise I am stuck. I have been trying to fix it for about a week now by myself to no avail
View 6 Replies View RelatedI've FC10 installed. After updating a few days back, I'm unable to use Network Manager to connect to the net through my USB Modem. All the threads I've read say to do
Code: yum update NetworkManager but how can I do it without net connection? Can anyone post the exact link of the Network Manager's latest and BUG-FREE rpm so that I can directly run it?
I recently installed OpenSUSE 11.2 and everything works fine except wi-fi card, of course. The problem is that after installation the system recognized the card (is was listed in network devices in Yast) but I was unable to enable it through network-manager applet. Though the device could make scanning through terminal (found article in docs but didn't fully understand wpa_gui). Then i was stupid enough to delete the device from Yast list to try to reinstall it. So the problem is that i simply can't do this cause i see no way to re-detect. That is the goal is to at least turn back to post-install system state and try to enable wifi card again.
View 9 Replies View RelatedI followed (or at least tried to follow) tutorials on doing this. I installed network-manager-pptp and tried to configure network manager to connect to a VPN. In the settings when I select MPPE with 128-bit encryption, after I've selected it and applied it, I check the settings and it's invariably unchecked. I tried using KVpnc after getting frustrated with network manager, and I can't seem to get that working either. I've been trying to search for info on this, and I can't seem to find anything on why I can't select MPPE with 128-bit encryption. That seems like it might be why I'm unable to connect to the VPN?
View 1 Replies View RelatedI have been using Hardy for about 3yrs now and using dialup to connect to the internet. I have a 64bit ASUS with a nVidia ethernet interface........I have just recently switched to cable broadband with a wired connection direct to the eth0 port. I have another computer running puppy linux in which the broadband works. hence this is how I am typing this now. I have connected my ubuntu machine to the cable and the network admin shows a wired connection but will not let me browse on the net with any browser. Not really sure how I got puppy to find it, but it did.
I have used the network manager on both machines with one connecting and the other not. I know there a newer ubuntu's out but I really do like Hardy and want to keep it, but without internet connection other than dialup it seems a bit lame. I am not above using command line options as I use wodim and wget all the time, so my question is.
I have duel boot (XP & Jaunty). I have installed Jaunty in one of my parition through wubi installer. Problem is, though my network connection shows active, I am unable to connect internet via firefox browser or any other browser.
1. I have plugged in ethernet wired connection.
2. I have single network connection (wired connection1)
Accidentally I removed the NM Applet from the panel and I am trying to reset it. When I right-click on the panel and "Add to Panel", I couldn't see Network Manager. Hence I couldn't connect to the available wireless network. I am able to add Network Monitor, which is similar to Network manager, but this just displays info about current network.
View 5 Replies View RelatedI'm running 64 bit Lucid on a HTPC that is networked with a Windows 7 64 bit laptop. Up until this morning, sharing media between these two worked fine. When I attempted to connect through Rhythmbox to play music, the computer couldn't find the files. I attempted to access the network through Nautilus and it was unable to mount the location. So I tried the Create Launcher command and created a link of the network on the desktop. I was prompted to login and it worked perfectly This has happened once before and the only way to fix it was to reinstall Ubuntu.I would very much like to avoid that if possible as the system is setup perfectly.
I wouldn't bother with the issue if it didn't prevent me from adding my music files to Rhythmbox. I have run findsmb as well as smbtree. Smbtree returned nothing and findsmb had a dotted line with nothing underneath. Nothing has been removed. I did install security updates this morning, but since it has happened before, I am more inclined to thing it is a bug or conflict somewhere.
I have a 5720 Mini PCIE broadband modem card and though it works, it won't connect automatically in a Ubuntu system. Network Manager says it is enabled when I right click on the icon, but when I do a left click it says it is disabled. I have to right click and disable and then enable before my Verizon connection will work.
View 1 Replies View RelatedI am completely new to linux an have read the replies to similar questions but am unsure of how to access the directory mentioned ~/.gconf/system/networking .I also do not have a system recovery disc or flash drive
View 7 Replies View RelatedI had trouble connecting to a wireless network with openSUSE, so I tried the YAST network manager to see if that fixed it. Not only did it not fix it, but now I cannot connect to any network, wired or wireless. I tried to open the default network manager and it said "Network management disabled". How do I re-enable it?I also have set YAST settings back to their originals with no luck.
View 7 Replies View RelatedI happened to Fedora 13 that the network manager does not indicate any wifi network and I had to turn off the notebook for a while and then recover, this also happened to me 2 or 3 times on ubuntu 10.04 too. my card is an Atheros AR5007EG.
View 2 Replies View RelatedI have a dell netbook with 8.04lts the network manager has been deleted and I am unable to install a new one
View 1 Replies View RelatedI'm using ubuntu karmic and I'm not able to connect to the internet with my reliance netconnect data card using network manager. Other distros like fedora, opensuse n sabayon connected easily with nm. Ubuntu detects the data card flawlessly but just doesnt connect.This problem has been persistent even in previous ubuntu versions, n I used to use wvdial. But downloading wvdial on some other comp with every dependency is really cumbersome.
View 6 Replies View RelatedI just updated from 9.04 to 9.10 (it's a long story, and I still can't go beyond 2.30).The update got rid of WICD, which is what I used and installed network-manager. Network-manager was not working at all, so I uninstalled it again and installed WICD. I could connect perfectly and had no problems.However, now the computer hangs during boot, saying that init can't start network-manager. I assume that something went wrong during the uninstalling process, since it wasn't updated.
This is the message: init: Failed to spawn network-manager main process: unable to execute: No such file or directory.
So how do I update it or manually change it so it stops requesting network-manager?
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
I have been using it with a plasmoid for weeks with no trouble, but I accidentally deleted my bottom panel and now I can't find the plasmoid (it's not in add widgets) and I can't control my internet, and the computer is not connecting to my default networks.
View 2 Replies View RelatedI tried to yum install libvirt but it says it is the latest.I have also checked that i have the latest qemu-kvm virt-manager virt-viewer python-virtinst.I understand that the error msg says that it is unable to find that certain file, libvirt-sock, and i dun think i have it either.
View 3 Replies View RelatedI tried installing Fedora 15 Gnome on my 8 year old laptop, but it didn't work so well since Gnome 3 couldn't start due to my graphics adapter (although it worked fine in Fedora 14), so I tried installing Fedora 15 LXDE and had much better results. Any way, after running yum update, I tried to install Google Chrome since I prefer it over FireFox, but I noticed that I didn't have the opton to automatically install it with a package manager, only download it. Once downloaded, I tried to open it via the GUI and it brought up a screen asking me what application I wanted to use to open the rpm. It didn't even know how to install a rpm!! I then tried to install it via the command line, but it failed because the package was dependent on others. After looking around in the Administration menu, there does not seem to be any package manager installed. How can this be? I've used many different versions of Linux before, but none that didn't have a package manager or didn't know how to install it's own native binaries. I don't get it.
View 5 Replies View RelatedI am rearranging my GNOME panels and was about to delete the network manager applet that lets me select and then connect to wireless networks, but then I realised that if I delete it - how do I get it back on another panel?The normal way of adding stuff to panels brings up a menu and I can't see any mention of the network manager applet. Where can I find it to add it to a new panel?
View 3 Replies View RelatedI�m using F14 x64 - I have installed both Gnome and KDE.I can�t create VPN/PPPOE connection in KDE network manager but I don�t have this problems on gnomeIs it possible to use gnome network manager in KDE?
View 14 Replies View RelatedWhen I install the FC11 by using"Install or upgrade an existing system"or"Install system with basic video driver"mode...Point 1, I can't config the network config ( IP Address ), due to theerror of network manager...Point 2, I can't enter into the text mode to do the installation steps.Remark:The machine is provide Web,DNS, and Mail Server on the NET ( Internet )
View 1 Replies View RelatedI installed aria download manager from this site:
[URL]
But now i am not able to remove it...through yum ..
I'm a new fedora-user and are having some problems setting ut everything as i want:
The host to always use WIFI
The host to not see the ethernet-connection.
The guest to use ethernet
The guest to be able to get wifi when no ethernet is avaible.
The guest to install from PXE
The guest is going to be a Windows 7. Nothing is done so far, as i cannot figure out how to do this.
I updated my FC10 just a day back. The problem is that Netwrok Manager has disappeared. And in spite of re-installing it, it doesn't appear on the panel when i enter 'NetworkManager' as root in the terminal.I have a USB modem right now. Update was made through a broadband connection. Ethernet works perfectly well but this USB modem of mine doesn't work at all. And I have to use USB not Ethernet.
View 9 Replies View RelatedI have got DHCP issues with Network Manager. Whenever I try to connect using static IP it works, but when I use use Netowork Manager with DHCP, it seems to try to connect and soon says "Network Disconnected"..I've managed to connect to wlan and eth using network, so there shouldn't be any hardware/driver issue.
View 4 Replies View RelatedI've upgraded to F12 from F11 (with a completely fresh install) and today is my 4th day using it, Now, mysteriously my network manager has disappeared from the panel, and it is not connecting me to the internet or showing wireless APs.I am able to get online using command line so it is only a minor problem but still a hassle.how can something so vital break so easily?Also nm-applet is listed in my processes and is "sleeping"?
View 10 Replies View RelatedI have a number of errors captured by SELinux against NetworkManager - text of one of those is below. I'm not really sure how to interpret it
[code]...