Fedora Networking :: Wlan0 Link Not Ready ?
Nov 1, 2009
The past couple days I've been attempting to use ndiswrapper to connect to my home network wirelessly and have run into a slight problem. I'm able to install ndiswrapper (of course), and install the driver. ndiswrapper -l comes up good, showing the driver is in place for my netgear wg311v3 card.
modprobe ndiswrapper I am able to get to work without errors, except, when i type ndiswrapper -ma it writes another file to /etc/modeprobe.d/ndiswrapper causing the deprecation error.
The card scans for networks, and I'm able type in my encryption key.
However it doesn't connect. | grep comes up with the error that the wlan0 link is not ready.
I think I've also been able to determine that the configuration I've put in to the card through the network manager is not actually configured.
Anyone know how I could possibly connect with the card.. It seems it should be able to work. alias wlano is also in place.
View 7 Replies
ADVERTISEMENT
Nov 6, 2010
I recently got a Tplink TL-WN321G wifi device for my fedora box. It has a Ralink chipset rt2870 in it.After messing it with couple of hours, i got it working with rt2800usb firmware, the LED is blinking on it and the device is listed in available...but its not scanning for available networks..lsusb:
Code:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
View 1 Replies
View Related
Apr 22, 2010
My installation has stopped detecting my wired network. Another computer connects fine with the same cable to the same access point. As far as I can tell it is simply behaving as if there was no network available from that cable but obviously there is. It was working a couple of hours ago, and I didn't install or uninstall anything, just shut down and booted up again.
LAN is enabled in the BIOS ifconfig does display eth0 ifup eth0 returns "Ignoring unknown interface eth0=eth0" in the output from dmesg:
"ADDRCONF(NETDEV_UP): eth0: link is not ready"
network appears in lshw and is not listed as disabled
View 9 Replies
View Related
Mar 24, 2011
fresh install of 10.1 on an older sony laptop wireless icon is on the toolbar, and my router is listed icon has a red exclamation mark my wireless button on the laptop is set to "on" dmesg | ndis reports "wlan0: link is not ready"
View 4 Replies
View Related
May 20, 2009
When I try to bring up my wi-fi PCI card (ifup wlan0 or ifconfig wlan0 up) my whole PC just hangs until I power it off.
I believe I have the right drivers, but cannot see what I am doing wrong.
I'd really prefer not to go down the ndiswrapper route.
Firstly, I can see the PCI card and the driver it is using :
Code:
[J@gx260-f10 ~]$ lspci -k
...
...
01:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
[Code]....
the PC just hangs for ever. No mouse movement, ctrl-alt-del, nothing.
I have downloaded a Linux driver from Realtek but it will not compile. I have the latest kernel-devel, headers, and gcc. I can post compiler errors if anybody would like. They're all apparently to do with missing parameters.
View 6 Replies
View Related
Nov 15, 2009
I have a desktop that has a d-link DWL-520 wireless card, which was working under Windoze. Today I installed Centos 5.4 on the system , which went cleanly. I then used Network Configuration to set up the wireless card. I specified to use DHCP, set the SSID and authentication password. When I tried to activate the card I get these error messages
Error for wireless request "Set Mode" (8B06): SET failed on device wlan0 ; Operation not supported. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0.
The hardware manager seems to have correctly identified the card and chipset, (Intersil Prism 2.5) and installed driver hostap_pci which came with the distro. This web site seems to suggest that this is the correct driver: [URL] searching forums I've found a few references to these errors, but they were from several years ago, and for different distros and cards. I did find a reference to using Network Manager to configure the card instead of Network Configuration. I started the NM service and configured a connection using it instead, but still no luck.
[Code]....
View 15 Replies
View Related
Jun 6, 2010
Also having this problem on Ubuntu 10.04.If I do "iwlist scan" I can pick up networks on wlan0:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
View 2 Replies
View Related
Nov 7, 2010
This morning I installed Fedora 14 on my laptop. During the setup, I was able to configure the wireless connection and use it to install additional software from the FreshRPMs and Livna repos. When the install was completed, I was surprised to find the wireless not working. When I click on the NetworkManager icon at the bottom right corner, I see "Wireless Networks" Under that it says "device not ready" and it is greyed out so it cannot be click on.
Running lspci -vnn returned
07:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR5001 Wireless Network Adapter [168c:001c] (rev 01)
Kernel driver in use: ath5k
Kernel modules: ath5k
Running lsmod confirmed that ath5k is in fact loaded.
View 4 Replies
View Related
Jan 25, 2011
I hav googled and tried everything postedoso reinstall fedora 14but still doesnot workI try to install these 3 fileskmod-wl-2.6.35.6-45.fc14.i686-5.60.48.36-2.fc14.1.i686.rpmerr: kmod-wl-2.6.35.6-45.fc14.i686-5.60.48.36-2.fc14.1.i686 requires wl-kmod-common >= 5.60.48.36kmod-wl-5.60.48.36-2.fc14.1.i686.rpmerr:kmod-wl-5.60.48.36-2.fc14.1.i686 requires kmod-wl-2.6.35.6-45.fc14.i686 >= 5.60.48.36-.1broadcom-wl-5.60.48.36-1.fc13.noarch.rpmerr:broadcom-wl
View 3 Replies
View Related
Apr 18, 2009
I am tring to get my linksys wireless router to connect to my laptop that i recently installed Fedora 10 on. Well it is actully running of an external HD. Any way when i boot in windows it connects and works fine, but when i try to activate wlan0 it says "Cannot activate network divice wlan0!" "determining IP info failed..."
View 11 Replies
View Related
Dec 29, 2009
We need to have the wireless associated with the access point prior to the first login.
Have not been able to get it to work yet. WPA-PSK. wireless will not connect until login.
This is necessary for nfs automount and openldap auth to work. Not a home networking environment.
How to troubleshoot effectively.
View 3 Replies
View Related
Dec 4, 2010
I've been able to get a laptop on Fedora 14 (2.6.35.6-48) working with a Netgear WNA1100 Once up and running, I execute "ifconfig wlan0 up" from root, and everything connects just fine and is stable as long as I stay logged in. But, I haven't found how to do this automatically on boot.
I've tried to use NetworkManager, but I cannot figure out how to get the GUI to show up - it says its running and enabled in the Services gui, but I haven't figured out how to actually use it! I checked to see if the nm-applet is running with ps, and for the user login, I see:
I'm not sure if the "sm-disable" flag is my problem, or how to change it. I'm not even sure if NetworkManager will allow me to set things up for bootup, but that is the path I ran down...
I assume this is a fundamentally easy process to set this up on bootup, but I'm not stumbling across the method. I recall doing this kind of thing years ago when I was an engineer, and before I got my lobotomy to become a manager...
View 1 Replies
View Related
Jun 23, 2011
Can't get wlan0 working:
In networkmanager the device apears unavailable.
View 6 Replies
View Related
Jan 10, 2010
I have a HP Elitebook 6930 with Intel 5300 wireless card and today I update it from Fedora11 to Fedora 12 and now I cannot connect with my home wireless network. Previously with F11 I connected without problems but now the wireless connection presents a "Device not ready" message. I tried to switch on/off the wireless card but without results. I had to set intel_iommu=off as kernel parameter to complete the boot. Is something related to it?
View 2 Replies
View Related
Jul 22, 2009
Having trouble with wireless and FC11, eth0 is ok. When I try to activate wlan0 through system-config-network 1.5.97, I get msg: Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0... failed. This is a compaq laptop.
<uname -r>
2.6.29.6-213.fc11.i686.PAE #1 SMP Tue Jul 7 20:59:29 EDT 2009 i686 athlon i386 GNU/Linux
<lspci>
The wireless card is Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter
(rev 01)
View 7 Replies
View Related
Nov 4, 2009
I would like to mount a bunch of folders/shares when I start my machine up. I will be adding the mounts into my /etc/fstab folder BUT my WLAN0 only comes "up" and connects to my WAP AFTER logging in.
how I get it to start on PC boot instead of log in?
I think I need to disable network manager but I'm unfamiliar with the procedure in Fedora
View 2 Replies
View Related
Feb 18, 2010
i can't get a pppoe conection working over a wireless network,in windows I have to connect to the router first, and then put in my user and password to get connected, but i don't know how to do this on fedora, i get connected to the router through network manager, and ping is ok, but when i try to make a new xDSL connection i don't know how to make it work through the wireless network that is established and working with my router.
View 9 Replies
View Related
Apr 30, 2010
Code:
Commands as root works well when normal user is logged in and connected to net via KDE 4 network manager, but after logoff network is gone. And it is impossible to get it back because command mentioned above stops working!
View 4 Replies
View Related
Aug 22, 2010
I am having a problem trying to transfer large file (~700MB) from one station in my home to another. I have 3 PCs hooked up through a router. 1 is wired to the router and the other two are wireless. One wireless is a laptop that has a built-in Atheros wireless card that was supported during the FC13 install. The other wireless has a plug-in wireless card made by Belkin (F7D1101). I had to use ndiswrapper to get it to work on FC13.(BTW all PCs are running FC13)
The one with the Belkin card is, I think, the problem. The one with the Atheros card will transfer files at a rate of about 8MB/sec to the one with the wired ethernet connection. The one with the Belkin card will not transfer at rates over 300KB/sec to either of the other two PCs. I have tried file transfers both encrypted and not and it makes no difference.
View 2 Replies
View Related
Feb 28, 2009
I do not know how it came to pass, but it has come to pass. I was in the process of updating my desktop Fedora 10 (KDE) system with yum, when I finished that I got a message about
Quote:
I have no clue what this means.
View 8 Replies
View Related
Mar 16, 2009
Since 2.6.27.19-170.2.35.fc10.x86_64, dhclient wlan0 doesn't seem to work any more.
However, bizarrely, dhclient eth0 does (to the same D-link wireless router).
The AP shows connected - tail /var/log/messages
No working leases in persistent database - sleeping.
WINXP connects just fine. This (B43) has worked nicely ever since FC10 came out, and I was able to use the WiFi at all kinds of places on a recent trip. Other than a couple of yum updates, I don't think anything else has changed since. Other devices on the wlan are getting their DHCP requests satisfied correctly.
Is anyone else having this problem since about a week ago? Perhaps there's something really obvious I'm missing. I can manually assign an IP address to wlan0, manually edit the routing tables and edit /etc/resolv.conf, and then Wifi seems to work OK, so it doesn't seem to be b43 itself unless it is dropping DHCPOFFERS. If this isn't a regression, does anyone have any tips about how to debug this?
View 3 Replies
View Related
Aug 22, 2010
I just installed Fedora 13 from the Live CD. FIrst off I read the guide and the first step doesn't even work for me. System>Administration>Network does not exist. If I go to System then Preferences I see a Network Manager but it looks nothing like what these screen shots look like. [url]
No wireless card show up in the wireless tab of Network Manager. How can I fix this since my card is listed in ifconfig and iwconfig. Wifi card is a Zonet zew2500p
View 2 Replies
View Related
Feb 3, 2011
what i want to do is
client <--> wlan0 <--> computer <--> eth0 <--> internet
i have 2 network connections eth0 wired connected to internet wlan0 wireless (work fine) i have installed hostapd with madwifi and so on oki when i run hostapd the clients see the hot spot oki clients connect with wpa oki network manager run at demand not automatic (keep it for internet help) now i'm a bit lost what do i need is wlan0 give the client an ip (dhcp demand) create a bridge between wlan0 and eth0 steps to create a permanent bridge between wlan0 and eth0
View 2 Replies
View Related
Feb 22, 2011
I have setup hostapd and a bridged setup with br0 bridging eth0 and wlan0. The setup works but unfortunately not on bootup. The reason is that the bridge can't add iface wlan0 because it is down for some reason at this time. When hostapd is running (after the network script) the interface is up and can be added to bridge via
[Code]....
View 2 Replies
View Related
Jul 3, 2010
I am still encountering problems getting the Broadcom 4321 chipset to work on my Fedora 13, even after using this guide, this guide and another guide on ndiswrapper.
To answer the standard questions:
Code:
Code:
Code:
Code:
and finally
Code:
But no wlan device or anything else.
View 2 Replies
View Related
Nov 13, 2010
Just installed f14 on my Toshiba laptop, which has a realtek ethernet card. i installed the drivers from the realtek site with no issues (also, i know the card is good, i had it working on suse a while back). No matter what I try, i cannot seem to get the computer to recognize there being a wireless connection (tells me no such thing as wlan0).ifconfig shows the following:
Code:
# ifconfig
eth0 Link encap:Ethernet HWaddr 88:AE:1D:F4:AD:88
[code]...
View 6 Replies
View Related
Apr 26, 2010
I have a problem where I'm using Ubuntu linux to mount a Windows Vista machine's USB drive and access it on the web using Apache. I did have the USB drive plugged into the Linux machine directly and that was working via the web. FollowSymLinks is on in httpd.conf
[Code]....
The mount works and I can see the files (see above) from my regular linux user account. If I make a test file in /mnt and soft link to that, I can see it on the web. So it's just the mount to the vista machine that seems to be a problem. It's supposed to be a simple read-only mount and the apache login should (I think) be able to see the same generic root access permissions.
log from apache: [Mon Apr 26 20:39:42 2010] [error] [client 99.99.99.99] Symbolic link not allowed or link target not accessible: /home/user1/pub_html/Music, referer: https://xx.xx.xx/~user1/music.html
The credentials have a login and password that matches a special read-only account on Vista. I can see the files on the system from Linux, but not via the web. As mentioned above, a different link to the same /mnt area works fine via the web. I've tried several different mount options with no success.
View 3 Replies
View Related
Nov 19, 2009
I want to know ; how to setting D-Link DWM 652 anybody can tell me how to do I have go back to windows again or I should stick to Fedora
View 2 Replies
View Related
May 8, 2011
How do I add a route that doesn't go away after a reboot? I tried adding to /etc/sysconfig/network-scripts/route-wlan0 and /etc/sysconfig/static-routes but neither of them did anything when I restarted network and NetworkManager. route command does not show the new route that I added. I tried this too - routes.html and there were no errors but the new route doesn't show up with the route command.I added "192.168.13.88/255.255.255.255 via 192.168.13.101 dev wlan0"
View 2 Replies
View Related
Mar 25, 2009
I want to link two servers (nets) 192.168.1.x and 10.0.0.x which use Fedora with firewalls.
View 2 Replies
View Related
