Fedora Networking :: LAN Stopped Working Through Wireless Router
Sep 17, 2009
I have a wireless router at home, but I usually have my laptop connected to it through an ethernet cable. It had always worked with no problems until some time last week when the wired network stopped working (but the wireless still works with no problem). At first I thought that it was some update, but no. My laptop works ok with the wired network at my office, and I also tried a different laptop at home and it didn't work. It's not the cable either, I tried a different one. I haven't changed any settings in my router.So I really don't know what's going on. I just find it weird that the router's wired networking suddenly stops working but the wireless still works fine...
View 1 Replies
ADVERTISEMENT
Apr 24, 2011
running ubuntu 10.10 on a toshiba laptop recently the wireless Internet stopped working from our netgear router, it still works for the Ienova laptop and emachines desktop using the router but this laptop will not work wirelessly internet cuts in and out on this laptop when on wireless when it didn't previously do so it reads a connection but will not load up web pages unless hard wired in with an ethernet cord.
View 3 Replies
View Related
Mar 18, 2010
I am having problem with wireless networking my fedora 12 since i opened network manager yesterday. But to my notice i haven't done any changes. But still i am not able find any reason for the wireless network not to work. When i try to restart the network servies it gives the following msg.
Quote:
Bringing up interface eth0:
This version of ISC DHCP is based on the release available on ftp.isc.org. Features have been added and other changes have been made to the base software release in order to make it work better with this distribution.
Please report for this software via the Red Hat Bugzilla site: [url]
Did i do something wrong with the network manager or did something go wrong with fedora.
View 2 Replies
View Related
Jan 9, 2010
I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.
After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.
Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.
Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:
yum info kmod-wl-PaE
Loaded plugins: presto, refresh-packagekit
Available Packages
Name : kmod-wl-PAE
Arch : i686
[Code].....
One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?
View 14 Replies
View Related
Mar 7, 2010
have a gateway nv78 laptop. I just ran the latest update on Fedora 12, and after Fedora stopped seeing wireless networks all together.
View 8 Replies
View Related
Sep 23, 2009
A few days ago (september 7) my wireless suddenly stopped working. I am using FC11, and have an Atheros AR5211 wireless card and have been using the ath5k driver with GNOME NetworkManager. Wireless networks are detected by NM perfectly fine. When I try to connect, the icon spins around those two dots, and one of them becomes green. If the network is wep protected, it asks for the password. After a while, it times out, regardless of the protection. I don't remember changing pretty much for the last two months, so I'm sort of surprised. I did download and install a kernal, along with an selinux-policy update.
If I run dmesg, relevant looking lines included:
ADDRCONF(NETDEV_UP): wlan0: link is not ready
and a long series of these at the end:
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
[code]....
Note: I previously posted this in "Laptops," but Networking seemed like a better place to do it.
View 14 Replies
View Related
Jan 12, 2010
I have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...
View 6 Replies
View Related
Nov 25, 2010
Right so yesterday my internet worked fine. Today - no connection at all. The light for my cable on the router doesn't even show up. I originally had indicator-network installed, so when the internet first stopped working, I tried a few other options such as tethering to my phone via usb and bluetooth (which I have successfully used in the past). However, these didn't work, and I figured that as connman is still in beta, maybe that was why. So I reinstalled network-manager and network-manager-gnome via a usb stick, uninstalled indicator-network, and rebooted the computer. Still no internet.
When I click on the applet, it says "No network devices are available". This is odd, as I definitely have a network device... it is part of the motherboard. So I thought I'd do the SMARTlan test or whatever it's called. It's part of my BIOS, so I ran that and it returned results that I (kinda) expected: when the cable wasn't plugged in, it returned one set of results. When it was only plugged into my computer (and not the router), it returned another set of results. And when it was plugged into both my computer and the router, it returned a third set of results. So that leads me to believe the cable itself is fine.
And when I move the cable to a different port on the router, nothing changes. The corresponding light still doesn't come on. Network-manager, telling there are no network devices. The BIOS can see the ethernet port and the cable. And the router is functioning perfectly for my parents' computer and my ps3. And I have checked the cable to my computer for physical damage - it follows the same path as the one to my ps3, and on top of that, nothing physical can possibly have happened to it in the last day. This happened once before, except I don't think the network devices were lost.
View 2 Replies
View Related
Jul 13, 2011
When originally installing 11.04 I had problems getting my Ralink 5390 wireless card to work.
Today my computer froze completely and I had to turn it off via the power switch. When I turned it back on, wireless was no longer recognized! My iPod can connect to the network just fine, so it must be an Ubuntu problem. There are no problems with my ethernet connection either.
I researched this and found several threads about blocking and unblocking wireless devices using the rfkill command. Well, unfortunately for me the rfkill command doesn't work. When I type sudo rfkill list or sudo rfkill unblock all, nothing happens; it just returns me to my bash prompt. I even tried uninstalling and reinstalling rfkill...nothing.
View 1 Replies
View Related
Feb 25, 2010
pulled the wireless USB adapter out of the back of my laptop when I was using it. I plugged it back in and it can see my wireless network, but it can't connect. Everytime it tries, it just shows the connecting icon on the top bar for a few minutes and then says that the network has been disconnected.
I've tried uninstalling and reinstalling the USB adaptor, but nothing I've done seems able to fix the issue. Anyone know how to fix this?
The USB adaptor I'm using is a Trendnet TEW-424UB
View 1 Replies
View Related
Apr 29, 2010
I have had ubuntu about a month now and everything has worked great up until now, I was surfing the web and all the sudden I lost connection. I tried to connect to the signal but got nothing so I did a reboot. After the reboot my wireless signal didn't show up. i right clicked the connection icon on the top taskbar and the enable wireless is blacked out to where i cant click it.
View 7 Replies
View Related
Aug 4, 2010
Just recently the wireless stopped working on Ubuntu 10.04. The machine is AcerOne AOA-150. I did notice recently the wireless would stop working, and I would need to either 1) reboot 2) switch the wireless off by moving the switch from left to right in front of the laptop.
However, this time nothing is working. I've provided some detail and if more information is needed, let me know.
LSPCI:
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
[Code]....
View 4 Replies
View Related
May 18, 2010
After upgrading to the latest Ubuntu, my wireless card stopped working. I keep on pressing the button but the little orange light wont come on...I have an aspire 5517 with "Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)" I have tried drpjkurian's tutorial for madwifi with no success . (http://ubuntuforums.org/showthread.php?t=1309072
View 2 Replies
View Related
May 25, 2010
I updated to 10.04 recently and everyhting worked fine. Yesterday my wireless stopped working. Now I just get "Networking disabled" when I mouse over the greyed out wireless icon. Everything still works fine when I boot windows.
Here's the details from the HOWTO log an wireless issue guide http://ubuntuforums.org/showthread.php?p=6183681 . sorry for the length of dmesg and lsmod , I couldn't figure out how to add a spoiler tag on this forum. code...
View 1 Replies
View Related
Jul 24, 2010
I'm using Ubuntu 10.04. I was happily connected to internet and surfing some forum, when wireless connection suddenly stopped working.
Now I can't find any access point, and I'm pretty sure I didn't do anything to justify this behaviour.
It already happened a month ago, but I had to format my drive, so I didn't really bother to try to solve the problem.
Anyway. I'm posting here the results of the commands I think I can help with a diagnosis; if something else is needed.
I'm using a different computer to post this thread, so I'm manually writing the output.
Code:
sudo iwconfig wlan0
wlan 0 IEEE 802.11bg ESSID: off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
sudo iwlist wlan0 scan
wlan0 No scan results
View 2 Replies
View Related
Oct 20, 2010
About a week ago I upgraded to Maverick from Lucid.
All networking worked fine on Lucid.
I am using an Acer Laptop with the Atheros AR928X Wireless Network Adapter.
I can connect to my home network (visible, with WPA2-Personal) fine. However, I cannot connect to my university's wireless network. The only difference I noticed is that its network is using WPA2 Entreprise with Tunneled TLS Authentication and MSCHAPv2.
I tried dmesg and I got:
wlan0: authenticate with 00:1a:1e:ef:f4:e1 (try 1)
wlan0: authenticated
wlan0: associate with 00:1a:1e:ef:f4:e1 (try 1)
wlan0: RX AssocResp frin 00:1a:1e:ef:f4:e1 (capab=0x431 status=0 aid=2)
[Code].....
Unless the driver has changed, I suspect this is not a driver issue, since it worked fine on Lucid. Is this a NetworkManager issue?
View 1 Replies
View Related
Jan 18, 2011
I have a HP Mini 5105 SSD netbook, runing Ubuntu 10.10 with 2Gb RAM. My wireless card is a Broadcom BCM43224 802.11a/b/g/n. Its driver is enabled and running. The wired network connection runs fine too. The problem: Wireless stopped working. When I right click on the network icon, the enable network option is clicked, but the "enable wireless" option is listed in dark grey and cannot be clicked on. I have recently updated my kernel version to 2.6.35-24-generic. What I have already tried: this one too I got to know there seems to be a problem with the 2.6.35-24-generic kernel. I have gone into the GRUB menu (it took some time to find out that you have to keep the Shift key pressed during startup for the GRUB menu to show), chosen the older kernel version (2.6.35-23-generic) and then removed the faulty one. Nevertheless, nothing has changed. I still cannot enable the wireless. The outcome to lshw -C network is:
[code]...
View 8 Replies
View Related
Apr 18, 2011
I'm running a gateway lapbook w/10.04 LTS and an etheros wirless card. Card has been working fine for almost a year - from cold boot, warm boot, and recovery from standy (shut lid, open, press power button). I was fiddling with setting a static IP for the wirelss card by modifying the interfaces text file. I made some changes, and restored the file to its original contents after some noodling around. Wireless still worked fine after that. Last night I took the laptop out of suspend as usual - lifted lid, pressed power button - but the wireless indicator remained grayed out and I haven't been able to reenable wireless connectivity since. ifconfig shows the wireless card is there, and cabling the e-net port directly to my hub works fine.
View 3 Replies
View Related
Jul 13, 2011
I go to the icon and it says "wireless is disabled by hardware switch", well I didn't press any hardware switch. My laptop is a Dell L501X, the "hardware switch" is the Fn button and F2. I've tried pressing this but nothing happens.
Is this a bug with the latest linux version? Cos everything was working fine until my laptop updated.
The version I have now is "Linux 2.6.38-10-generic"
I'm running 11.04 64bit.
Here is some info from console :
Quote:
me@XPS-L501X:~$ sudo ifconfig -a
eth0 Link encap:Ethernet HWaddr f0:4d:a2:59:00:34
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::f24d:a2ff:fe59:34/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]....
View 5 Replies
View Related
Jan 20, 2010
Today my wireless has stopped working. I have a laptop hp6720s with network controller: Intel corporation PRO/Wireless 3945 ABG [Golan] Network connection (rev 02), dual boot vista/ubuntu 9.10, fully updated (kernel 2.6.31-17). I use a router edimax BR-6204 wg to use the net with other laptop. Till now i have using wicd for controll wireless without any problem, internet was quick and responsive. (Quick connection without any failure).
But today the internet was very slow and wireless starts to connect and disconnects intermitently, doing it unusable. This was what occured when i upgraded from jaunty to karmic and used the network manager from gnome, but then i fix the problem installing wicd. Now wicd behaves in the same way as gnome-network-manager. If i connect directly the computer to the router by wire, i have internet and everything works perfectly. How i can fix the wireless?. How i can do it works with ubuntu 9.10 and?.
View 1 Replies
View Related
May 5, 2010
after having tried out almost all suggestions found here and elsewhere on the internet, i'm somewhat at my wits end The situation: I'm running Kubuntu 32Bit Version (at the mom 10.4) on a HP-Compaq 6735s (AMD Processor, Vanilla 32Bit Install). My first Install was last year with 9.4 and the Broadcom 4322 wireless worked like a charm after installing the proprietary STA-driver under System -> Hardware Drivers. As the update didn't work out really without glitches, i did a fresh install and lost my wireless. I tried various combinations and tutorials but to no avail. My card is found, the driver installed, but i cannot access my access-point. I can SEE the access point (and all my neighbors'), but knetworkmanager does not seem to do anything. To be sure, I installed wicd (nice tool by the way). Trying a connect here told my my credentials were bad (incorrect passphrase for my WPA2 Personal auth), which is not true. I tried connecting without security, didn't get an IP. So it seems somehow the card is working, but all functions needed for passing information to the access-point are unavailable.
This is what I tried:
both broadcom-drivers
fw-cutter
installing the driver by hand
Installing the driver via Hardware Drivers produced the same results as any other, viz the card is working, but not connecting. Unfortunately knetworkmanagers error messages are a bit sparse, or rather non existant. My guess is that somehow the firmware is not properly loaded (or the wrong type??).
View 9 Replies
View Related
May 7, 2010
i have lucid installed on my toshiba laptop after after an update my wireless stopped working keep asking for password and my wireless card is not detecting no wifi :
*-network UNCLAIMED
description: Ethernet controller
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
View 4 Replies
View Related
Jul 9, 2010
Like many others it seems, my wireless has stopped working since a recent upgrade The answer does not lie in analysis of logs, settings etc. but surely with those who did it - they should provide a fix. I cannot believe everyone expects each individual users to go into their own analysis of why this is no longer working as it is clearly widespread. I have been using Ubuntu for 18 months without this problem on the same dual-boot laptop, and it still works on Windows as before, only Ubuntu 10.4 has recently stopped my network card from working.
I need to know when this will be fixed. I have been embarrassed by promoting Ubuntu to many colleagues who now also cannot work at home on their wireless networks. Seriously disillusioned I may start looking for a more stable alternative to Windows.
View 9 Replies
View Related
Sep 4, 2010
I have an EEE 1000 that successfully connected to WPA networks until yesterday. I tried re-installing the RT2860 drivers that had been previously modified and did not have success.
Additionally, I just installed 10.04 on a Gateway laptop that's a few years old. It immediately connected to the WPA network and I ran the updater. Lo and behold, after updating it no longer connects to the network.
View 4 Replies
View Related
Sep 21, 2010
I'm not a total newbie, but run into some strange problems with my installation of Lucid.Everything was working fine yesterday. I shut down the laptop and powered it up this morning and had problems with network. I have two NICs (wired and wireless). Both are set to pick up IP settings from DHCP and both do, however when using wired network I can't communicate with outside world - can't even ping the default gateway (but pinging 127.0.0.1 or IP address of the NIC no problem, so stack should be OK).When on the wireless network everything works fine (otherwise I would struggle to write this post ).What is very weird though is that I have a VMWare Player installed and using Windows VM on wired network works just great!
I noticed that when you're persistent it happens that you can ping but huge chunks of traffic are lost (e.g. packet 1-10 would pass, 11-40 would be lost, 41-59 would pass and so on).I restarted Ubuntu, tried shutting down interfaces, disabling networking and nothing helped. I don't recall performing any changes (at least that I would be aware of).Can anyone suggest something?BTW. This is not DNS issue as both IP addresses and FQDNs do not work. When I refer to using a given network (wired or wireless) the other one is down with ifconfig command...
View 1 Replies
View Related
Oct 9, 2010
I recently installed 10.04 and everything Just Worked.Before Lucid, I was using 9.04 and had successfully gotten my Broadcom 4306 working perfectly... which is why I think the Lucid install went so perfectly.Well, after a botched hiberation (Dell Inspiron 9100), my wireless is dead in the water.I've tried "ifdown", "iwconfig", "/etc/init.d/network restart" and "force-reload", 'modprobe -r b43'
View 1 Replies
View Related
Nov 15, 2010
I'm using Maverick and since yesterday, my wireless hasn't been working. It was working before with Maverick and I don't recall doing any updates that might have changed wireless configurations.
By "doesn't work" I mean it doesn't recognizes any networks, as if the wireless was turned off (there's this button on laptops, but it's turned on). I had that problem some time ago, but rebooting solved the problem, which, now, didn't.
My laptop is a HP dv6420la.
Where to start?
View 9 Replies
View Related
May 11, 2011
Well, I have an issue with my wireless card in Ubuntu 10.04, my wireless card model is:
the D-Link WIRELESS N 150 DESKTOP ADAPTER DWA-525. I was already successful getting it to work by using the RaLink driver suggested here and following the instructions in their readme.But after a system update I performed through Update Manager (in which I guess the kernel was updated), the device stopped working completely. The wireless icon remains(in the top panel), but it displays a red exclamation mark next to it
View 9 Replies
View Related
Feb 21, 2010
Just upgraded from Intrepid to karmic on my girlfriends Dell Vostro 1510 and the wireless stopped working. The drivers are installed and worked fine under intrepid. When I enter the hardware drivers utility it says that the driver is active but currently not being used.
iwconfif output:
Code:
lo no wireless extensions.
eth0 no wireless extensions.[code].....
View 3 Replies
View Related
Apr 8, 2010
I have ubuntu 9.10 and my wireless connection has been working perfectly until a few weeks ago when I updated my laptop. I can connect to the internet using my wired cable but not by wireless. There is nothing listed under my wireless list. I am new to this and have been unsuccessful in getting my wireless connection going again. I don't even know were to begin. I have a 2wire modem also.
View 2 Replies
View Related
