Fedora Networking :: Set The Ip Address To Device?
Nov 20, 2010How to set the ip address to particular device(ethernet device)
View 4 Replies
ADVERTISEMENT
Networking :: Set The Ip Address To Particular Device?
Nov 20, 2010How to set the ip address to particular device(ethernet device)
View 2 Replies View RelatedNetworking :: Ip Address Keeps Getting Forgotten When No Device Attached?
Mar 24, 2011I have a 2nd ethernet card in my system that I use to share my internet connection. eth0 is connected to the internet, and eth1 is used for my 2nd computer to connect into. Whenever the 2nd computer is turned off, eth1 forgets its ip address, then when then 2nd computer is turned on, it can't access the internet until I reset the ip address on eth1 ("ifconfig eth1 up 192.168.1.1). I only see this behavior under ubuntu 10.04, not the previous distro that ran on this box, slackware 12. How do I keep eth2 from forgetting the ip address when no computer is attached?
View 6 Replies View RelatedCentOS 5 :: Device Eth0 Has Mac Address XX Instead Of Configured Address?
Oct 22, 2009after a yum update on my CentOS 5.3 I got this error when shutting down eth0 on reboot...
Shutting down interace eth0: Device eth0 has MAC address XXX instead of configured address XXX ignoring [FAILED]
Fedora X86/64bit :: Libvirtd And Lxcstartup Errors After Reboot - No Such Device Or Address
Jan 7, 2011Unfortunately accidentaly I disconnected my usb drive my computer and my VMs run from so I just rebooted for a quick fix Now I can't open virt-manager locally and the VM's can't get network connections I see this in the logs after the last two reboots
Code:
grep lxc /var/log/messages |tail -n 2
Jan 7 00:45:04 F820 libvirtd: 00:45:04.524: warning : lxcStartup:1895 : Unable to create cgroup for driver: No such device or address
Jan 7 11:52:53 F820 libvirtd: 11:52:53.325: warning : lxcStartup:1895 : Unable to create cgroup for driver: No such device or address
[code]...
I tried restarting libvirtd after with no love so I rebooted and cgroup was gone this was a clean install of F14, after this started I brought the system current, I can provide the packages installed but they errors didnt change
Fedora Networking :: 3G USB Modem Has Wrong Device Port In NM - Change Device Port In Network Manager?
Aug 14, 2009I installed ZTE MF 626 modem in my F10 with kernel 2.6.27.12-170, i run usb_modeswitch and so far things happened normally. Watching through /var/log/messages it says that F10 detects two port device for this modem: ttyUSB1 and ttyUSB2, and in the sequence it disable port ttyUSB1 BUT Network Manager still set this port.I mean, when i connect via wvdial appointing to ttyUSB2 i get connection, but Network Manager fails to do it appointing to ttyUSB1. How to change device port in Network Manager?
View 1 Replies View RelatedCentOS 5 Networking :: Kernel Rpm Install After Error "Bringing Up Interface Eth0: Device Eth0 Has Different MAC Address Than Expected, Ignoring"
Dec 26, 2010i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedSoftware :: Find Out Device IP Address?
Sep 1, 2010what would be the simplest way to find out device IP address? I don't know its factory set address, so my plan is to connect laptop directly to it with ethernet. it should respond to ping.
View 7 Replies View RelatedUbuntu Networking :: Port Forwarding From Public Address To Private Address?
Feb 24, 2010Currently my OS is Ubuntu 9.04 Jaunty Jackalope Desktop OS and my web server is Apache2. I have a public address 60.x.y.z and my pc local address is 10.x.y.z. I have a web app in my Apache2 which currently run in localhost(10.x.y.z).
I would like to enable the web app so that it could be browse from outside. I know there maybe some port forwarding process and some commands involved in order to do that. But I have no idea on the steps to do that.
Networking :: Error Str2addr:Address 35 Outside Range Of Address Field Length 1?
May 12, 2011I am working on implementing a protocol on NS2.34 .I really need help to solve this problem . Actually , I don't now whether the problem is generated by the tcl code or the c++ code when I run the simulation, I get this result :
Code:
num_nodes is set 64
INITIALIZE THE LIST xListHead
34
45
channel.cc:sendUp - Calc highestAntennaZ_ and distCST_
highestAntennaZ_ = 1.5, distCST_ = 550.0
SORTING LISTS ...DONE!
code....
Networking :: Program To Assign Globa LIPv6 Address And Bind() To The Previously Assigned Address?
Apr 24, 2010Consider the following program:
Code:
#include <stdio.h>
#include <stdint.h>
[code]...
Hardware :: Using Printer Port - No Such Device Or Address
Mar 14, 2010I am trying to use the printer port. But, I get this
Code:
Broadcom EJTAG Debrick Utility v1.6r-hugebird
Failed to lock /dev/parport0: No such device or address
johnh@tux:~/Ubuntu One/hh$
run from johnh I permission denied sudo-ing I get above.
General :: Mount Error 6 = No Such Device Or Address
Feb 10, 2011[root@servers guest]# /bin/mount -o -uid=root,gid=root,username=userid,password=user1passwd //172.16.1.212/backup/user1backup /mnt/tmp
retrying with upper case share name
mount error 6 = No such device or address
Refer to the mount.cifs(8) manual page (e.g.man mount.cifs)
[root@servers guest]#
I also tried:
[root@servers guest]# /bin/mount -t cifs -o -uid=root,gid=root,username=user1,password=user1pass //172.16.1.212/backup/user1backup /mnt/tmp
but no luck!
General :: Bind Static IP To A MAC Address Of The Device?
Mar 16, 2011Ubuntu was a good choice for free server O/S. I am currently downloading it. My ISP wants to bind my static IP to a MAC address of the device that will be making my connection for me. Should my server be behind my router or in front of it? I kinda wanted it to be the access point and be able to monitor the usage from all the terminals in my house. We have 4 other PC's, a laptop and a PS3. My server is a Acer Altos G530 with 3.2 Xeon Processor, 4 gb of ECC DDR,
View 7 Replies View RelatedSoftware :: Device Eth0 Has Mac Address / Instead Of Configured
Jul 29, 2011I am trying to perform VM cloning using KVM in a centos 5.6 machines. I copy the memory contents of a running vm to an external state file and try to use that to start another VM in a different machine. While starting the cloned VM I provide a different mac address but once it resumes it has the old one . I tried changing the mac address in ifcfg-eth0 but I get the error: Device eth0 has a mac address xx:xx instead of configured xx:xx.Ignoring .
Is there some way to change the ip/mac of the cloned vm without the need to restart the VM ( Then the purpose of cloning will be defeated). Thanks a lot for the info.
Slackware :: USB Hub Device Not Accepting New Address (Error -71)
Nov 1, 2010Slackware 10.2. My usb ports work fine when used directly. When I insert a USB hub to duplicate a port I get the message USB device not accepting new address=2 error=-71
View 1 Replies View RelatedUbuntu Networking :: Static IP Address And The Install Configures For A DHCP Configured Address - Network Not Starting
Dec 16, 2010Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
Ubuntu Networking :: IP Address Set To Manual But Still Queries DHCP For Address
Mar 12, 2011I'm running Ubuntu 10.10 and I'm having problems trying to assign it a static IP address. No matter what I put in the Preferences->Networking area (identifying the interface as Manual)... it still will query DHCP for an address if I run the dhclient command. I'm using to using ubuntu server where I just set the IP in the interfaces config file.
View 1 Replies View RelatedNetworking :: Dynamic IP Address With PTR Record Versus Fixed IP Address Without?
May 7, 2010I am running my own Postfix mail server. Some time ago I noticed that most email was rejected because of the server's dynamic IP address. So I got a fixed IP address. However then I noticed that some mails got rejected due to failing the reverse DNS check. So my ISP told me to get a range of IP addresses and they could then create a PTR record for one of those addresses. That is now running but it turns out that the IP address used for the PTR record is a ... dynamic IP address. So Spamhaus PBL rejects my emails again.
View 1 Replies View RelatedUbuntu Security :: Block Device By Bluetooth Address?
Apr 22, 2010Is it possible somehow to block some bluetooth device with specif address (mac) ?
(like iptables block by mac)?
Ubuntu Servers :: DNS - Ping A LAN Device By Name - Get Reply With Only The IP Address
May 2, 2010I have configured DNS on ubuntu server 8.10 and it is working fine. There is one question I have though. Everytime I ping a LAN device by name I get the reply from the server with only the IP Address.
View 2 Replies View RelatedServer :: Tune2fs: No Such Device Or Address While Trying To Open /dev/sda1?
Apr 3, 2011Last night, OSSEC sent me some warning emails related to bad hard disk:Code:Apr 3 20:26:58 207 kernel: sd 0:0:0:0: SCSI error: return code = 0x06000000
Code:
Apr 3 21:57:52 207 kernel: EXT3-fs error (device sda1): ext3_get_inode_loc: unable to read inode block - inode=299533439, block=599064613
[code]....
SUSE / Novell :: DNS And 127.0.0.2 Address / Loopback Device Lo Has Two Addresses?
Apr 19, 2010We�re experimenting with deploying SUSE 10 SP3 systems and adding them to a Windows domain and DNS. Oddly, when we register in DNS, it gets registered under two address: the real IP address, and the address 127.0.0.2. Also, an ip addr command shows that the loopback device lo has two addresses: 127.0.0.1 and 127.0.0.2.
The above behavior is just on SP3. On SUSE 10 SP2, the lo device has only the 127.0.0.1 address, and the system is able to register correctly in DNS.
Do you know what the 127.0.0.2 address signifies, or how to get rid of it?
Networking :: Bind External IP Address To Internal IP Address?
Jun 7, 2009I have a few external IP's assigned to me by my ISP. I have IPcop as my router/firewall. I am wondering how to bind 1 of my external ip's to my internal ip address. So I do not have to port forward, etc. For Example, 77.77.77.77 to 192.168.1.123 and on the server it see's the external IP address.
View 2 Replies View RelatedFedora Networking :: How To Change The Mac Address
Feb 17, 2009Some people may need to change the mac address of their ethernet network cards. This can be easily done with fedora with command line. Just follow the steps below:
1. Log as root on a textual console (ctrl+F2) or through "su -" command in your console
2. Print your network configuration with ifconfig
[root@localhost ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:23:8B:6A:7E:9E
inet addr:10.1.128.244 Bcast:10.1.255.255 Mask:255.255.0.0
inet6 addr: fe80::218:8bff:fedb:7e9e/64 Scope:Link
[code].....
Here, eth0 is the ethernet interface of your system. The mac address is put in red.
3. Change your mac address using the following syntax
ifconfig eth0 hw ether 00:18:8BA:7E:90
The new value (in green) must be hexadecimal
4. if you have a dhcp server that distributes the adresses automatically, then request a new adress for your eth0 interface
[root@localhost ~]# dhclient eth0
5. Now, your interface is up and have a new mac and IP addresses. This feature may be useful if the network administrator ban you according to the mac adress, for example .........
[URL]
Fedora Networking :: Cannot Get IP Address For Eth0
Aug 2, 2009I downloaded Fedora 10 32bit and put it on a Dell Dimension 8200 to save it from the recycle bin. Everything seems to work except I cannot get an IP addr. Roadrunner is my ISP using a cable modem and a Linksys Instant Broadband Series Etherfast Cable/DSL router model BEFSR41. In system-config-network, the nic shows inactive. If I activate it a window opens saying "determining IP information for eth0". After a short time the message adds the word "failed". Using a Windows PC on the same network, I can look at the DHCP connections on the Linksys and I see the MAC addr for the PC running Fedora.
From the OS installation, /etc/sysconfig/networking/devices/ifcfg-eth0 has following:
DEVICE=eth0
HWADDR=00:80:ad:d1:88:c9
ONBOOT=yes
[Code]....
Fedora Networking :: Specifying DNS Server Address
Aug 3, 2009I have specified Primary DNS address in Network Manager's DNS tab and saved those settings. But when I restart my PC, Primary DNS address will go blank. How can I save this address premanently?
View 6 Replies View RelatedFedora Networking :: All Eth Devices On F9 Box Have Same IP Address?
Jul 28, 2010What I am trying to do is the following: I have many IBM MT-M 6223 towers (Intel Xeon processor) that need to run a certain Fedora 9 configuration. It is working on one box, now it needs to be replicated on all of the others. What is being done is the working box is cloned, and then that image is loaded on all of the others.These boxes have 5 total Ethernet devices. There is one on-board port, and there are two 2-port expansion cards for a total of 5.
There was one initial problem out of the gate that has since been solved (or perhaps not completely). What was happening is that the boxes that received the cloned image had their Ethernet devices misnumbered. Instead of eth0 through eth4, they were numbered eth5 through eth9.This was eventually traced to the following file: /etc/udev/rules.d/70-persistent-net-config. That file contained the original settings from the box that was first cloned. It had eth0 through eth4 at the top with MAC addresses belonging the box that was the source of the cloned image. It looks like this mismatch was detected, and five more entries, numbered eth5 through eth9, got appended to the bottom with MAC addresses belonging to the new box.
Once /etc/udev/rules.d/70-persistent-net-config was deleted, and the machine rebooted, the 5 ethernet devices came up with the correct numbering (0 thru 4). /etc/udev/rules.d/70-persistent-net-config was rebuilt with the correct devname-MAC pairing.
Now for this new problem.... Part of the configuration across all these machines is that only eth3 should have an IP address. It is a static IP address set through the /etc/sysconfig/network-scripts/ifcfg-eth3 file. All of the other devices must NOT have any IP address. They are either not used or used only for raw Ethernet.After clearing out /etc/udev/rules.d/70-persistent-net-config, /etc/sysconfig/network-scripts/ifcfg-eth3 was edited to give the new box its own unique static IP address before rebooting.Sample ifcfg-eth3 file:
Code:
DEVICE=eth3
BOOTPROTO=static
[code]....
Fedora Networking :: Change IP Address In KDE?
Mar 26, 2011I've just reinstalled F14 with KDE rather than Gnome and I'm finding that I'm unable to assign a static IP address to my wired connection.
KDE automatically connects via DHCP, but when I go into KDE's network manager, the eth0 connection isn't listed. In fact, no wired connection is listed. If I manually add one with the correct settings (including a static IP), it switches back to DHCP upon rebooting.
How can I get around this? Should I install the networkmanager-gnome package?
Fedora Networking :: Define A Name For This Ip Address?
Jun 9, 2011i have run a ftp server with vsftpd. i set a public ip address on my server . but i want to define a name for this ip address (for example ftp.test.com) how can i do that?
View 5 Replies View Related
