I had F10. Today the system suggested to upgrade to F11. In the middle of upgrade (during the installation of files) my computer had frozen for a 10-15 min. I rebooted it. Nothing is working now. I can not boot F10 and upgrade F11 does not want to continue.
View 2 Replies
I've just reported a launchpad bug report about my desktop system being unbootable after upgrade to lucid lynx. [URL]... I opened this thread to ask if someone else experienced a similar problem and for collecting information and workarounds (none yet) about this quite serius problem. The system has an nvidia graphic card and proprietary drivers were installed before the upgrade. However I'm not sure the problem is related to this. FYI, the system booted regularly from a usb stick with ubuntu lucid lynx. SO the problem is in the upgrade path.
View 9 Replies View RelatedI upgraded from 10.04 to 10.10 a few hours ago using the alternate CD. I selected not to download files off the internet as I wanted to do that at a later stage. After running for close on an hour performing the update, as it reached the end it gave me a message saying the update had failed and the changes will now be restored (or something like that). I clicked ok, and the update window closed. I then restarted the pc and it stopped at the splash screen. Now I cannot get it to load the desktop environment. It Jst sits at the splash screen. Pressing the power button shuts it down normally, but alt-ctrl-f1 does not open a shell.If i start up using recovery mode and then select fail safe graphics mode something comes up about a segmentation fault in xserver in I then end up at the shell where I can work from the command line, but can never get the graphical interface to work.
View 8 Replies View RelatedOn my laptop I dual boot Ubuntu 8.04 and Windows XP. During the last upgrade of my Ubuntu distro something went wrong and now I get a messed up GUI. In the meanwhile I got a new laptop on which I only run Ubuntu 9.10. So my question is: I want to delete the linux partition on my old laptop and use only Windows XP but since I use grub to dual boot, I'm afraid that deleting the linux partition and extending the Windows partition will cause problems to boot my computer.
Here's a screenshot of my partitions:
I ran the 11.04 upgrade. At the end, it reported a failure, implied a recovery would occur and the upgrade then finished. The recovery was supposed to have run sudo dpkg --configure -a. That does not appear to have happened. I am concerned that a reboot will render my system inoperative.Has anyone else experienced a similar issue or have any suggestions? What information should I provide. report.
View 2 Replies View RelatedToday I ran preupgrade and chose Fedora 14 instead of Fedora 15 to be safe to upgrade from 13 . After lengthy upgrade, I wan able to login but after that whenever I try to open terminal and enter su to login as root, it suddenly hangs or sometimes it hangs by itself or even hangs after reboot. So I have totally corrupted upgrade.
I read somewhere and found I can go to GRUB menu at reboot and I can choose fedora 13 from there and was glad at least I can go back to old Fedora 13 but I do have to go to GRUB menu to choose Fedora 13 every i have to reboot. Is this OK? Now in Fedora 13 I have entered command as root: preupgrade and this time I chose Fedora 15. Is this OK? I am hoping the upgrade from 13 to 15 would work.
I recently installed Fedora 10, having chosen that version in order to be able to use the packages created by the Planet CCRMA group for doing audio recording (they don't have F11 packages ready yet, AFAIK). Last weekend I got a prompt to upgrade my system, and I naively accepted it, not even realizing that it was an upgrade to F11.
The upgrade didn't work, for reasons that I still don't know (probably a video driver issue), but since I know the F10 installation worked, and Planet CCRMA is not up to F11 yet, I'd just like to downgrade myself back to F10.
Can I just re-install Fedora 10 from the DVD I used before, or will the F11 installation cause problems? I haven't really done any work that I mind losing, so I'm not too concerned about overwriting my previous installation.
Quote:
I've upgraded to fedora12 from fedora11 using preupgrade.
The process was successfull till the first boot, where I got above error message.
I have just upgraded my FC12 installation to FC13. The initial boot failed (just blank screen). Second time I received 'selinux targeted policy relabel is required'. I let that run, but still the boot did not suceed.
I then went in to verbose boot and saw that the boot would hang at libvirtd. So I disabled libvirtd for anything above run level 1. Next boot failed at atd, disabled atd. Next boot failed at 'monthly Smolt checkin'.
At that point and booted in to single user mode and dissabled SELinux, thinking that was the cause of all the problems. That did not help.
The update process has also removed my previous kernels, so I can't test a different kernel
I tried to upgrade ubuntu from 9.10 to 10.04. It is almost complete downloading packages,but i get this error:Failed to fetch http://archive.ubuntu.com/ubuntu/poo...untu2_i386.deb The HTTP server sent an invalid Content-Range header [IP: 91.189.88.30 80]I tried to change from main server to US server, but I still get this error.
View 1 Replies View Relatedwent through the tutorial on FedoraSolved for securing ssh. I installed denyhosts with yum and then tried to run it with the command line command"sudo /etc/init.d/denyhosts start" but I got the message"Job Failed. See system logs and 'systemctl status' for details [FAILED]"and in the application "services" in the applications menu,t shows an exclamation warning and says that "This unit has failed"
View 1 Replies View RelatedI use the automatic upgrades - they hardly ever cause a problem... until now.
I just applied this upgrade (linux-image-2.6.32-5-amd64) and a restart was required (normal under when upgrading the image).
After the restart my SIP phone software didn't startup - didn't even get any errors in the log file...
So I checked the "System Monitor" to see if the process was running but not displayed... the System Monitor generates a core dump...
I hope there will be another update to solve this really quickly.... not sure what else is broken. Firefox is still working and so is Skype.
I want to upgrade my F11 system to F13 using preupgrade-cli. Can I do that directly, or should I first upgrade to F12 and then to F13?
I have read elsewhere that Anaconda can skip one but not two versions, is that correct? If so, I assume that moving directly from F11 to F13 is OK, right?
I have a problem after upgrade from F13 to F14. I used the DVD i386 Iso on my Netbook MSI Wind U100 but it's don't start. It's load the services and it's stuck in the Fedora logo. I boot into Runlevel 1 to see the logs but there is no error. Then I run init 5 and it's stuck after the service ATD load. I don't want to do a clean install.
View 4 Replies View RelatedI upgraded F14 to F15 using installation DVD. I have been upgrading since F11 with no problems. Upgrade went well, no issue. After the reboot, the system hangs after the last line systemd.
These are last lines from boot.log:
Starting LSB: start and stop xinetd...
Started LSB: Mount and unmount network filesystems..
Starting Permit User Sessions...
Starting xinetd: Started Permit User Sessions.
Starting Display Manager...
Started Display Manager. [OK]
Started LSB: start and stop xinetd.
Right now I am on system rescue CD, can mount partitions and read logs. I would like to avoid fresh installation if possible.
I try to install Fedora 11 from DVD BUT after installation system is not booting. Windows XP is a 1st OS is already installed in my system.
View 1 Replies View RelatedI upgraded from F10 to F12 using preupgrade. The upgrade itself completed with no errors, but I'm unable to boot afterward.
Symptoms:...Grub starts, the initramfs loads, and the system begins to boot. After a few seconds I get error messages for buffer i/o errors on blocks 0-3 on certain dm devices (usually dm0 and dm2, but I can't get a shell to figure out what those are). An error appears from device-mapper that it couldn't read an LVM snapshot's metadata. I get the message to press "I" for interactive startup. UDEV loads and the system tries to mount all filesystems. Errors appear stating that it couldn't mount various LVM partitions. Startup fails due to the mount failure, the system reboots, and the steps repeat.
Troubleshooting done:...I have tried to run preupgrade again (the entry is still in my grub.conf file). The upgrade environment boots, but it fails to find the LVM devices and gives me a question to name my machine just like for a fresh install. I also tried booting from the full install DVD, but I get the same effect. Suspecting that the XFS drivers weren't being included, I have run dracut to create a new initramfs, making sure the XFS module was included. I have loaded the preupgrade environment and stopped at the initial GUI splash screen to get to a shell prompt. From there I can successfully assemble the raid arrays, activate the volume group, and mount all volumes -- all my data is still intact (yay!). I've run lvdisplay to check the LVM volumes, and most (all?) appear to have different UUIDs than what was in /etc/fstab before the upgrade -- not sure if preupgrade or a new LVM package somehow changed the UUIDs. I have modified my root partition's /etc/fstab to try calling the LVM volumes by name instead of UUID, but the problem persists (I also make sure to update the initramfs as well). From the device-mapper and I/O errors above, I suspect that either RAID or LVM aren't starting up properly, especially since prior OS upgrades had problems recognizing RAID/LVM combinations (it happened so regularly that I wrote a script so I could do a mkinitrd with the proper options running under SystemRescueCD with each upgrade).
I have tried booting with combinations of the rootfstype, rdinfo, rdshell, and rdinitdebug parameters, but the error happens so early in the startup process that the messages quickly scroll by and I just end up rebooting.
System details:4 1-TB drives set up in two RAID 1 pairs. FAT32 /boot partition RAIDed on the first drive pair. Two LVM partitions -- one RAIDed on the second drive pair and one on the remainder of the first drive pair. Root and other filesystems are in LVM; most (including /) are formatted in XFS.
I've made some progress in diagnosing the issue. The failure is happening because the third RAID array (md2) isn't being assembled at startup. That array contains the second physical volume in the LVM volume group, so if it doesn't start then several mount points can't be found.
The RAID array is listed in my /etc/mdadm.conf file and identified by its UUID but the Fedora 12 installer won't detect it by default. Booting the DVD in rescue mode does allow the filesystems to be detected and mounted, but the RAID device is set to be /dev/md127 instead of /dev/md2.
The arrays are on an MSI P35 motherboard (Intel ICH9R SATA chipset) but I'm using LInux software RAID. The motherboard is configured for AHCI only. This all worked correctly in Fedora 10.
I've been excited about F15 being the first distro with GNOME 3 as default, and so I used preupgrade to download all the things necessary to upgrade my system (Fedora 14 atm) to 15. When I boot into Anaconda however, I get an error message that root doesn't have enough space for installation. Even after I removed KDE from my system, I apparently still didn't have enough. Is there a tool similar to Ubuntu's "autoclean" that can remove orphaned dependencies and the like so I can clean up root? I really want to try 15!
EDIT: I suspect that preupgrade might be dragging KDE stuff back onto my system even after I pretty much purged KDE from my system. Anything I can do to stop this?
I've been using Ubuntu since 6.04, not a linux guru by any means but can usually get myself out of trouble.
So, the issue... I installed 8.04 on my mother's laptop some time back as she was having trouble keeping Win 2000 running (she has a low spec no-name generic laptop btw). I live in Autsralia and she in England, i thought i could better support her if she was running Ubuntu... All has been well with 8.04 but with the new LTS release (10.04) i thought i'd talk her through the upgrade... Did the online upgrade via Update Manager, all seemed to go OK but when she went to log on after restart she got an error saying 'authentication failed' even though we are 100% sure we have the user name and password correct... Tried to do a ctrl+alt+F1 to by pass the GUI log on but couldn't get the terminal session to open up, just got a black screen - no command prompt.
So... thought OK re-install... downloaded the ISO, burned and sent her a CD in the post... talked her through the re-install, all seemed to go well (again) - BUT, after restart, couldn't log in "authentication failed" again...
So, remember i'm trying to talk a novice through all this... any thoughts!?!
If i can get her to log in i can then support her via some kind of remote sesion or other screen share... and it wont cost me a small fortune in international calls!!! But if i can't get a log in, i'm dead in the water!?
I installed FC11 from installation cds twice and I'm having a problem with Firefox freezing the system. The mouse cursor will move but nothing else is responsive, including mouse buttons and keyboard.I checked the media on every disc and they all check fine.I never had this problem with FC10. I tried upgrading Firefox -- with the necessary dependency upgrades too but without success.I tried to downgrade to FC10 Firefox and ran into a great big hassle with that.
View 4 Replies View RelatedI've had such good luck with Fedora (and this Forum), I'm attempting to put F12 on wife's brand new Sony Vaio, a VPCEB11FM, a 64bit system. I downloaded the Fedora-12-x86_64-netinst.iso, made sure it was ok with sha256.exe, then burned the image to DVD. Booted it up and let it default to "install or upgrade an existing system". It dead-ended in a dark blue or black screen. I re-started and examined the other options. Thought I'd try the one that says: "Install system with basic video driver". Got all the way through to where it got ready to start downloading files. Can't get past that point because it attempts to get to the Internet using the Sony's wireless card! Why would it try the wireless when there's a wired NIC card in this PC that requires no special driver etc. How to proceed from here?
View 3 Replies View RelatedWhen booting the system ,"starting system logger : Failed" after that i login to the system as usual but the system logger cannot start,even i use the service syslog restart command,how can i solve such problem ,thanks a lot
View 1 Replies View RelatedSystem fedora10
An IDE hard disk
Equipped with two IDE drives (one dvd drive a dvd burner drive which both share an IDE cable) Just using the system - Management - updatesystem the software upgrade of the upgrade is complete to allow the resumption of a problem was the
1, the normal boot drive two lights are flashing above but after the restart only the DVD drive light flickering burner did not react
2, when the show after the show graphics motherboard models that can enter the boss that dell card will be nearly 2 minutes (the past, each time on boot or restart the screen only shows a few seconds) then self-organized (here in particular explain if the motherboard model shows that by then dell would have been completely stuck only by restarting)
3, self-completed fedora10 select Start (here Please note that if the first question will not be the normal boot into the fedora restart if it is then that some characters will be displayed after the duplicate has been duplicate unless you press the restart)
4, in the end this thing have updatesystem Why are used with the yum update to update how things ah not the same as how to turn off the options I have at him inside the selection are not updated but not used
Say over these problems are in the use of upgraded updatesystem caused ago have never been Open the case I have put the hard disk drive memory and so on have won the cup to another mounted on a boss, or no longer put into the restoration of the factory set up is not effective
I just installed Fedora9 in my desktop. The installation was successful and it was doing security update and system update right after install. After all the update service finished, I do a manual update to see what happy (Sysem>Administration>Update System). It keeps coming up with Package Error with the message "failed to get a TID: Incorrect path with ';' returned!".
View 8 Replies View RelatedI recently tried to upgrade to 10.04 and it failed somewhere on the installation process. I managed to get the machine to boot and go into gnome but now very few programs will actually launch (terminal, nautilus and firefox is about it) and the install/update software reports al sorts of dependency issues
[Code]...
I had installed Ubuntu 8.04 and partitioned my drive to share 500gB with Windows XP. All was good. When I saw that Ubuntu 10.01 was available I downloaded it to update the 8.04. Ididn't want to have to redo all my configurations so told installer not to update config files. No entry in GRUB no boot. Tried to re-install 8.04 to replace 10.01 and get back to intial state. Current state Ubuntu won;t boot, XP still OK but don't know how to clean up my mess. I've attached a copy of a boot info script I ran.
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 0.97 is installed in the MBR of /dev/sda and looks on the same drive in partition #6 for /boot/grub/stage2 and /boot/grub/menu.lst.
[Code].....
I ran the software manager upgrade/update install of 11.04. When I reboot almost immediately a quick error flashes on screen that says something like "missing prefix" then it goes to an unfamiliar menu with kernel choices that are very old and look nothing like my desktop. I think it may be some old install or something I dont know. I have an eee pc. I originally installed with WUBI but have done other kernel upgrades with no issues.
View 2 Replies View RelatedI have configured the remote installation of Fedora 13 with kickstart with nfs installation method. All work ok until I boot the Fedora 13 client system.
Fed13 client system receives the IP address from dhcp, receives the loader, loads vmlinuz and initrd.img from tftp, load anaconda, configures the network and dev eth0, mounts nfs server to load kickstart file, loads kickstart file (language...) but when it tries to mount nfs server to install from Fedora 13 installation tree it fails.
First, I thought that I had an error on my NFS configuration but I was wrong. I opened tty with ALT+F4 on the Fedora 13 client and I sew this error:
Code:
Is this a bug or can I modify anything to correct this error? How?
I am going to try out the new release but when I try to upgrade I get
Failed to fetch [URL] 404 Not Found
and
Failed to fetch [URL] 404 Not Found
--Began with an up-to-date Ubuntu 8.04.3--64 LTS install; tar-copied everything from sda2 to sda3 and booted SDA3 so I wouldn't fry my main install:
[[ ' fdisk -l /dev/sda /dev/sdb '
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x86dae77a
[Code]...
Will attach any logs requested; but I'm about to scrap the failed install and start over, 'cuz I want to test 10.04 LTS and the new Vmware Workstation 7.1--64 beta. The only thing I can think of is that I did not boot into the new kernel ( apt-get upgrade ) before doing the dist-upgrade. I've done a few of these dist-upgrades in the past this way; 6.06-LTS to 8.04, 8.04 to 9.x, etc
