I have found two problems with the DVD (checksum and media test are both OK).
1. On the Install boot loader (grub) page , if you change the name of the install from Fedora to something else, anaconda crashes, lol.
2. Worse, the installer hangs just after that .
Quote:
Retrieving installation information for installation repo is displayed, but the system just sits doing nothing.
I have just completed a dual boot installation of FC10. The install was done from CD's I downloaded from the Fedora website. The installation (seemed to have) went fine, and the machine still boots into XP if selected from the menu. The Fedora installation does not complete the boot process. I have three bars that move across the bottom of the screen, and the Fedora 10 graphic tuns white, and then the system hangs. I have let it sit at this screen for as long as 30 minutes. The screen will blank occasionally, but returns to the same place if I hit a key on the keyboard.
I have it installed on an old HP E800 netserver, running dual P3-866mHz processors, 2GB ram, a ATI Radeon 7000 video card, and three 36GB SCSI drives, non-raid. I know FC10 will run on this machine, as I have a friend running it on another E800 without any problems. This machine does have on-board video that is disabled only by plugging a different video card in (Phoenix BIOS).
Install from x64 DVD seems to have gone OK but 1st boot to welcome screen where user is added always hangs.I've done the install multiple times and no joy on any of them.I'm experienced with Fedora and had 10 installed on the same machine with no problem.Hardware is an HP d5000t.Quad core IntelNV graphics adapter8 Gig of memoryVista on a raid 0 by itselfFedora on a 320 Gig WD drive by itselfSuse 11.1 on another 640 Gig WD drive by itself
View 2 Replies View RelatedI just got a new dell 15z and it hangs on the install "Waiting for hardware to initialize"of the 64bit fedora. I have tried both the nomodeset and noprobe and still to no avail. I have also tried installing ubuntu and the installer will not run so im at a loss. Any ideas from the fedora community.Is there any way I can debug anaconda so I can see where it is hanging?
View 2 Replies View RelatedI am trying to install fc11 on an intel mb with pentium4 and ati graphics
the install always hangs at the point where the sw packages have been selected
and the install is checking dependencies.
I have tried the regular install
the basic video install, and text install
with the same symptoms each time
the dvd drive lite is on and the hard disk activity lite is on and the system is frozen.
have to power off.
I have fc11 installed on another system (amd) and had install issues also but that was
with the preview.
I am trying to install Fedora 11 from a DVD. Not the live DVD, the full DVD and it hangs constantly. I had to wait 10 minutes for it to Find Storage Devices, 10 minutes to input a root password and now I am waiting for the drive shares to be setup. It's already been 10 minutes. I verified the disk and everything was fine. Why is this taking so long?
View 4 Replies View RelatedI have a Dell Optiplex 760 Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
running:
I tried to upgrade to FC11 via download and DVD and in both cases the install hangs on bootstrap right after remounting the root filesystem in read/write mode.
Since it hangs in this manner, I have not been able to gather any logs...
Im trying to install fedora 11 from the live CD and when i get into the CD meny where it says "boot" and "press tab for boot options" i press enter. then a bunch lines flash across the screen with a lot of error messages. then the fedora loading bar at the bottom loads. hangs for about 1 minute at the very end. then the GMD screen appears. But the GMD screen is all out of place and its patchy as if my graphics card was causing some kind of error
View 1 Replies View RelatedI performed a clean install of Fedora 15 from DVD and it goes fine until the end when the install program says to reboot the computer. Once I do that, the computer hangs before Grub loads, i.e. just after all of the BIOS messages, so there isn't any error message to indicate what is wrong. I had no issues with Fedora 14.
View 3 Replies View RelatedAfter installing Fedora 15 from LiveUSB and rebooting it just hangs on a black screen with a blinking cursor (underscore) in the top left of the screen. If it's reached grub, it isn't responding to any commands, and mashing several key combinations (such as ctrl-alt-f1) will produce a beep usually emitted only by the BIOS (hinting that it may never be making its way to grub).
The only particularly interesting thing about the install is that by default it wanted to boot itself from the MBR on my primary-master (Windows) disk. Instead I selected the option to boot from "the first partition in sdb1", which is my primary-slave (Linux) disk, (the first partition being /boot). This way I can change which OS boots by changing the boot order in my BIOS, and so avoiding bootloader wars.
Trying to install Ubuntu (tried several releases) on HP Pavillion Pentium 4 Proccessor 515 2.93 Gig 1M L2 cache 533mhz 90nm . Have 1 gig ram and 1Tb hd. Hangs on initial install screen for ever. Tried versions from 8.10 (origional disk) to 11.01. Machine works perfectly on Windows XP but who wants that? The model is pavillion 1000 system number pl397aa.
View 7 Replies View RelatedI am trying to install Ubuntu 10.10 x64 on a HP Pavilion p6565uk.
My PC is x64 compatible, although ubuntu will not install.
I don't get to any gui, it says ubuntu will continue install in 5 seconds, at 0, nothing happens. The CPU light is flashing, but nothing happens.
After about 10 minutes, it reboots, but when the HP splash screen shows (Before the boot selection screen) it just hangs. I have to do a hard shutdown to boot back up.
I am using wubi for install.
I am a neophyte to linux so please cut me some slack. I'm installing the latest version of ubuntu on my old Dell Latitude C840 Laptop. (386 desktop install from CD). I cant seem to get past 79% completion. It just hangs there. I have to assume I'm not the first person to have this problem. I'm reasonably adept with computers but all of the threads/blogs that seemingly address this problem are lost to me. Can anyone provide a simple... or at least step by step process on how I can fix this?
View 1 Replies View RelatedTried to install Suse 11.4 on Core 2 Duo 3.16 GHz 4 GB RAM PC alongside Win XP.Installation progress was fine. I rebooted. The gecko appeared and the process bar kept going just about 1/10, then froze. I saw that it froze at the Loading AppArmor Mounting security fs on /sys/kernel/security.I tried safe-mode and it also froze at the same step. tried installing suse 11.3 -- and ended up with the same problem.
View 1 Replies View RelatedI'm trying to upgrade an EeePC from 9.10 (I think it is) to 10.10. I've tried two different thumb drives and a CD, redownloading the UNR image each time. What happens is it will get the the screen where it says 'Preparing to install Ubuntu-Netbook'. I hit forward, and then the little dial just spins indefinitely. I've also tried plugging the thumb drives into different USB ports, and playing around the with the hard disk compatibility mode on in the BIOS (currently set to 'compatible', but AHCI, IDE Enhanced etc made no difference).
View 9 Replies View RelatedI have installed Ubuntu 64bit 10.04 LTS version. I am trying to install open-iscsi and my apt-get install commands hangs code...
my sources.list seems to be fine. What might be the issue?? never had this issue on a 32 bit version of Ubuntu 9.
I want to try the new 11.1. When I start the installation (x86_64 DVD), the startup is hanging. The last message is "Starting udev...". Keyboard is completely frozen, only reset button is working. Mobo is an Intel DG965WH with 4GB RAM and ATI Graphic card (ASUS1950pro). My opensuse 11.0 runs without any problems.
View 9 Replies View RelatedI just upgraded my system's motherboard with an Asus M4N78 Pro and did a clean install of 9.10. The install seems to go fine but when it finishes and does the final restart I seems to get stuck at the place you'd normally see the GRUB menu. Instead all I see is a black screen with a flashing cursor in the left corner. This isn't just a long boot, its stuck. It never progresses past this point.
During the install everything seems fine. Video, network etc. I've tried several reburned CDs and I get the same result each time. For the record I've installed Ubuntu as a single partition an IDE drive. The bios is set to boot from that drive. ow the heck can I figure out what is happening? Is there a way to boot and display any and all messages displayed? Is this thing hanging in GRUB somewhere?
I can not get ubuntu to install on my workstation. I have the 64-bit cd (am currently trying the 32-bit cd with similar results) and it won't install. I get to the ubuntu splash screen with the 5 dots underneath it and it looks like it's trying to run for several minutes. After the several minutes, the screen simply goes black and I can't do anything.
View 8 Replies View RelatedI just installed Ubuntu 10.10 on a vostro 1000 laptop using standard configuration.I repartitioned the whole disk for Ubuntu. Now, when starting up Ubuntu, it appears to log in fine, but right near the end of the theme and before the desktop loads, it hangs, repeating a slice of the intro music over and over again. What could be causing this problem?Note: On every ubuntu disk I use, it also says that modules/..../Kernel something is missing from the disk quickly before booting the live session.
View 1 Replies View RelatedI'm on an HP Pavillion dv1000 laptop. I used a live CD to install Ubuntu 10.10 to an external USB hard drive. The install completed successfully, but after a reboot I am stuck on a black screen with a white cursor. Before that I see nothing but the initial HP startup screen. I am able to run the live CD without problems, and I have been running Ubuntu from a 4GB thumb drive (which I installed on using the same live CD that I used to install on my current external hard drive). I had no problems whatsoever running from the CD or thumb drive, so I can't figure out why the external hard drive would be so different.
View 7 Replies View RelatedI am attempting to migrate from Mandriva to Ubuntu and attempted to install the 11.04 and 10.04 CD distos on a 7-year old computer (Elite Group L7VMM3 motherboard, 1.4 ghz AMD Duron, 1.2GB RAM, 40GB IDE HDD).
The 11.04 installation CD makes it through the HD partitioning (erase everything), Computer name, time zone, and keyboard detection, but hangs after starting the "Copying files" stage of the install. The progress bar stops just below the in "Copying files...".
The 10.04 installation CD makes it through the "Installing the base system", "Retrieving console-terminus" with the progress bar stalled at 6%. Although the computer is old, Vista successfully installs on it.
I installing Fedora 12. I did ALL the same as in the installation guide, GRUB installed into MBR. And after installation and rebooting - nothing happens, after BIOS messages there is nothing - computer hangs. GRUB seems to be not installedI have 2 hard disks. At first I tried to install on the 2-nd drive(it is slave). Afterward I detach one disk and try with only one hard disk(it is master). Nothing changes - computer hangs.
View 3 Replies View RelatedI downloaded the .ISO for Fedora Core 14 Live, with the intention of installing it to my HDD.
I burn the .ISO with no reported problems.
I boot to the installation CD and can get to the point where it asks me to Login (a timer is also going down for Automated Login).
Once I click "Login", nothing else ever happens.
I can hear the disc spinning in the drive and it's trying to load something, but it never does.
I thought that maybe my older (2003) laptop might just be slow, so I allowed it to do whatever it seemed to be doing overnight while I slept.
Well, I woke up this morning and it was still doing the same exact thing with no results.
---------- Post added at 05:54 PM ---------- Previous post was at 05:51 PM ----------
Oh, and I intend to dual-boot. I have already made a partition using Norton Partition Magic. It's NTFS filesystem for now, but I figured the Fedora Installation would give me an option to use that partition anyway - NTFS or not (meaning, it would wipe the NTFS file system and use whatever it is that Fedora Core uses). Am I mistaken in assuming this?
As most of us know when you start the machine with the Install Disc in the drive you get a menu that reads:
Welcome To Fedora 15!
Install a new system or upgrade an existing system
Install system with basic video driver
Rescue installed system
Boot from local drive
Memory test
But when you try to boot the install DVD on and EFI based Mac...you only get
Booting Fedora 15 in 3...2...1 ...and then the system hangs.
If any users are having trouble with Fedora Install Media...you can usually use the Install Media from a previous release! In this case, I used the Fedora 14 (64-Bit) disc to install Fedora 15 by simply replacing the 'F14' with a 'F15' in the URLs of the Install and Update repository dialog boxes.
System is hanging during boot after a successful fresh install via netinstall disk. Never makes it to any GUI or prompt. However, it does still respond to CTRL-ALT-DEL (not completely frozen).Default debian installation with one exception - KDE checkbox was checked for installation. Everything else was default, with "use full disk with GRUB" option chosen.The boot process appears to hang during the service starts. It appears that the start job for "Create Static De..." is not actually ever completing. I don't know how to troubleshoot that any further than I have.
This is running on hardware, it is not a virtual machine. 480GB SSD, i7, 16GB of RAM, AMD R9 390 (I dunno if this is the problem, but it seems a likely culprit).There are no other disks attached. I have verified successful memtest completions (0 failures) and hard disk is intact and working fine (I have swapped for another disk, and the same thing happens as well).
My skill level with Linux is relatively low. I have proficiency using it and programming for it, but not much in the way of troubleshooting/ installation/ drivers.
Here is an album of "screenshots" (phone photos) of the boot sequence in debug: URL....I tried booting straight to console by removing "quiet" from boot options and changing to "text", but it does not alter the outcome in any discernible way.
Have downloaded the image twice now and burned it to CD twice. This is a brand new HP 6530b. It will boot to the CD and come up with the ubuntu install menu. I can arrow up and down, but when I press enter on any entry nothing happens. The CD will spin momentarily but then stop. Been trying to make this work for two weeks.
View 4 Replies View RelatedUbuntu and right now I am running it inside Windows. I burnt it onto a cd so I could install it onto my 2nd harddrive. I know the cd is fine. When I boot off the cd a purple screen loads up with some weird symbols at the bottom looks like a picture of a battery = and then a picture of a stick figure man. If I hit f6 I can get to the option screen. I've tried using noapci, nomodeset, disabling the framebuffer, and vga=normal. None of them work as soon as I hit enter to start installing Ubuntu it just sits there on the menu screen and never does anything.
View 5 Replies View RelatedI have a pretty old acer lap top. I used to run xubuntu on it, then I formatted it and installed freeBSD just to check them out. I tried to install last version of xubuntu then, and I got a message that /dev/../loop0 couldn' d mount or sth then I learned about lubuntu and I tried to installed them but I tried both a dvd and a cd and on both cases after I select language and "install on this machine" I just see a screen with 4 red dots writing "Ubuntu 10.10" that stays like this forever.. and nothing happens. the same if I select to boot from the cd just to check the environment. I then tried a ubuntu-studio dvd I had handy just to see if this would work - and it started installing as expecting, I cancelled it after a while. how to get lubuntu running?
View 4 Replies View RelatedI am trying to install webmin on my Debian virtual machine and it is not working.
Here is what i am following [url]
I ad the 2 lines to /etc/apt/sources.list I ad the key ok But when i do apt-get install webmin it goes through everything ok as far as i can see, except when it gets to " **initializing cache. This may take a while **Setting up webmin (1.550) ... " It is like it just stops doing anything, it just hangs there.
If i reboot and try "dpkg --configure -a" it starts at the same place "Setting up webmin" but nothing is happening.
