Fedora :: How To Run And Scan With AVG?
Dec 12, 2009I just installed AVG antivirus, but I didnot see shortcut in the MENU.How can I run it?Meybe I need some terminal command to run it and scan my HDD?
View 13 Replies
ADVERTISEMENT
Debian :: Eeepc Wifi - Every Time Scan For Network Using Iwconfig Wlan0 Scan Or Wicd And Computer Completely Freezes
Jan 9, 2011I installed squeeze on my eeepc 1015ped and downloaded the correct firmware-brcm80211 drivers but every time I scan for my network using iwconfig wlan0 scan or wicd, my computer completely freezes. I previously had a solid install running xmonad, and wicd was working like a charm (using the same broadcom driver) but i tinkered too much with it and decided to do a fresh install. I haven't quite run into a problem like this before.
View 2 Replies View RelatedFedora :: Scan With Xsane And HP C6380 All In One
Dec 21, 2009I started a thread that just brushed on the topic of running Xsane to scan with my HP c6380. However, the subject did not go very deep. It was alot about the printer, but not very much about scanning. It was also a previous installation and version of FedoraKDE. Now, I would like to take a moment to ask how to get Xsane up and running so that I can scan with my printer. I have it installed using $yum. However, the icon has not appeared anywhere and I am stumped.
View 14 Replies View RelatedFedora :: Amarok Can't Scan My Collection
Feb 21, 2010Ok, I stopped using Fedora after the version 9. Today for a change I installed Fedora 12. And now I am in an endless world of troubles.At first I was able to video call friends on msn. But it wasn't working. And then I found this guide and did everything it says. Now it's even worse, audio and video call buttons are greyed out?
Amarok is a critical software for me. No Amarok, no Linux. I installed the amarok's latest version through yum. But amarok can't scan my collection. It keeps giving this error "[ERROR!] Tried to query an uninitialized m_db! ".???
Fedora :: Scan Url And Downloading Files
Feb 1, 2011I understand wget is used to download files. Is there a way I can search a url for what files are available for me to download. I need to install a plug-in from an adobe website.
View 2 Replies View RelatedFedora :: Scanner Light Goes Off After Each Scan
Apr 15, 2011I'm using a scanner with Fedora. However, linux does something that is undesirable; It turns off the scanner light, everytime it does a scan, which the HP software, which comes for windows, doesn't do. The result? The light never warms up enough and all the images come with a blue tone on them. Only after using the scanner a few times, the light warms up enough and the images start getting their true colour.The question is, can I somehow force the light to stay on, even during scans, like it happens when I am using Windows? Or not? Anyone has ideas?
View 3 Replies View RelatedFedora :: Which Tool Can Use To Scan Ports
May 26, 2011I will scan my ports which are open or closed.Which tool can I use to scan my ports.
View 4 Replies View RelatedHardware :: Can't Scan With HP Photosmart (Fedora 13)
Feb 6, 2011I can print with HP Photosmart Plus e-All-in-One B210a with Fedora 13, but I can't scan anything. I'm using HPLIP 3.
View 3 Replies View RelatedFedora :: Amarok Crashes When It's Scan Collection?
Jun 7, 2010I upgraded my fedora 12 to F13 last night by Fedora 13 DVD. then i updated my F13 using this code:
Code:
#yum update
so when i tried to use amarok it couldn't scan my collection and crashes.
after that i removed my amarok folder using this code:
[Code]....
Fedora Hardware :: Simple-scan Not Updated In F13
Mar 25, 2011Simple-scan is not updated in F13 repositorys, why ?
Version is now : 1.0.2-1.fc13
Updated version is : 2.32.0.1
According to hompepage : [URL]
Why is simple-scan not updated to latest version ?
Fedora :: Scan And Save As A Text File?
Apr 26, 2010Fedora12/Kde4After a Sane Scan how do I Save a scan as a *.txt file ? gocr does not work, I can save in any other format but a txt file.
View 6 Replies View RelatedFedora Security :: CLAM AV - What Is The Console Command To Scan
Nov 12, 2009I installed CLAM AV and also the GUI (CLAMTK).
1). What is the console command to scan all of Fedora, not just a specific directory, but the entire computer?
2). Even tho I have consulted the CLAM AV site on how to update to the latest virus signature database, I don't either understand what they are telling me to do, or I am not "getting" how to do it.
X86/64bit :: Get Scan Function Of Printer To Work With Fedora 15?
May 29, 2011I got the printer to print, but I do not know how to get the scan function of the printer to work with Fedora 15.
View 4 Replies View RelatedFedora Security :: How To Determine What Type Of Files Clamav Can Scan
Dec 7, 2009How to determine what type of files clamav can scan? For example, if there is no unrar installed it can't scan files in it. So is there any way to find out all types of files that clamav can't scan?
View 2 Replies View RelatedFedora Hardware :: HP Photosmart B109a Scan Doesn't Work
Feb 25, 2010Printing works fine. I've printed documents ant photos - all is ok.Build-in card-reader works well.But I can't scan with him in fedora.I've installed libsane-hpaio .
View 9 Replies View RelatedFedora Networking :: Iwlist Scan In The Terminal But That Doesnt Seem To Work?
Jun 24, 2010generally whenever there is a wifi connection available fedora will detect and i can establish the connection but today i am not able to see any such wireless network available. I am in a wifi accessible area and i need to know how this can be rectified. i tried iwlist scan in the terminal but that doesnt seem to work
View 1 Replies View RelatedFedora :: Driver / Software For Automatic Feeder Scan Device?
Oct 17, 2010Recently, I bought the HP Officejet 4500 especially because of the automatic feeder for the scanner. The device is not supported by Fedora, but I found the driver for it at the HP driver site for Fedora 11 and / or 12.Now, I have two questions. First, I wonder why these drivers are not part of a Fedora distribution yet. Is there still some issue with it going on (something related to my second question or something completely different)?Second, the software (Sane) doesn't recognize different sheets of paper. When I place some 20 sheets of paper in the automatic feeder, the scanner scans them all, but only the first sheet is processed by Sane.Now, I saw that Sane in Fedora 13 is different than in Fedora 11 or 12. I expect it is improved, but I have not been able to work with it yet. Can I expect that it does recognize different sheets of paper from a scan with an automatic feeder?
Fedora Networking :: Investigate Virus Using To Port Scan Edu Sites?
Nov 17, 2010I installed F14 on a friend's computer a couple of weeks ago. Today she called me saying that her ISP called her telling her they'd have to cancel her internet if she didn't fix whatever virus was sending port scans to edu domains that they'd gotten complaints from. I thought "well, there's a first"... I've got ssh to her computer, so i shelled in and ran a couple of commands, but i really know very little about how to investigate this kind of stuff.
She's directly connected to her cable modem via cat-5; but she does have a wireless card installed --she just doesn't use it, nor a router, afaik, nor as far as i'd seen when i setup her printer. I googled a bit, and ran a couple of commands, and 1 of them was interesting because it APPEARS that her wireless card is ON and the eth0 is OFF? Perhaps someone will know how to read this output better than i, and the output of the other command that i ran. Also, does anyone know any other ways to properly investigate this one? FWIW, she does use transmission to download torrents.
Anyway, here's the commands i ran:
Code:
[root@localhost ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00.
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:21:97:9b:70:29 brd ff:ff:ff:ff:ff:ff
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 00:1e:e5:9c:b6:8a brd ff:ff:ff:ff:ff:ff [root@localhost ~]#
Fedora Networking :: Scan From Network Multifunciton Device - Using Scanner
Jan 9, 2011I have installed a new network multifunctional device Samsung CLX-3185FN using the drivers provided by the manufacturer (Samsung Unified Driver). The printing over the network works fine, I can administer the device using browser. The only problem I have is using scanner over the network. It works fine if I disable firewall, but is blocked with firewall enabled. I can not figure out which ports or port-range I must enable for this scanner. Do you have any information on this one or how can I found out the necessary ports to open?
View 3 Replies View RelatedFedora :: Scan 35mm Negatives With HP 3310 - Get Higher Quality Scans?
Feb 21, 2010I have a HP 3310 multifunction unit. Using HPLIP system it will print quite happily (though oddly the printer has to be on before the computer has booted for the networking to work!Now I'm trying to get the hang of scanning 35mm negatives using it + Fedora 12 (32bit). xsane seems to be the way forward, I can get a poor scan back but seem unable to find a way to tell the software I am scanning negatives and so to only scan the areas containing the film strip (HP provide a negative holder taht fixes the strip in right place on glass) to get higher quality scans. Anyone with any experience of scanning 35mm negs using HPLIPs/xsane/HP3310 ?
View 1 Replies View RelatedFedora Servers :: Several Postfix - Test Antivirus Scan Using Eicar Test Virus ?
Apr 8, 2009I have installed Postfix + Amavisd-new, then I am started all services (and configured main.cf and master.cf to use amavis).
The questions are:
1) I am trying to test antivirus scan using eicar test virus
Code:
And the message is successfully delivered to mailbox with mark "CLEAN" in maillog. But I cant see any attachment using
Code:
Where is my mistake?
2) Should I update clam and how I can do it?
3) Is spamassassin enabled by default in amavis (I have started daemon)?
4) Where configuration files of spamassassin is stored?
Fedora :: Scan Modem To Identfy Dial Up Modem?
Feb 3, 2010Steps for using scan Modem to Identfy dial up modem?
View 1 Replies View RelatedUbuntu :: Memory Scan On CD?
Oct 22, 2010One of the things I found really handy about the Live Ubuntu CDs is they had the option to run a memory scan on the computer. As the head of an IT department of one person in charge of maintaining 60 computers, that capability has helped me more than twice.
I think the options when running off CD/USB were Install Ubuntu, Test Ubuntu, run a memory scan, or boot off the harddrive. However, starting with Lucid and continuing with Maverick, the only options on the Live CD/USB seem to be install or try (although the memory scan is available on my Grub menu after Ubuntu is installed, unfortunately, most of the computers I am responsible for at work are Windows only).
Is there a way to start the memory scan when running a Live Lucid or Maverick CD/USB?
Ubuntu :: AV To Scan Windows ?
Jun 3, 2011Is there an AV i can use to scan my windows partition to find any bugs/backdoors or viruses? I know there is a backdoor somewhere, and comodo isnt picking it up so i am refusing to boot from my windows 7 right now. My password information keeps getting changed and websites and emails are alerting me that someone has access to them and is trying to promote spam.
View 9 Replies View RelatedUbuntu :: Can't Scan As A User?
Jun 4, 2011I have just installed 11.04 (64-bit) and I cannot scan as a user. Scanning as root works fine. My device is a Brother MFC-7420. I've installed the brscan2-0.2.5-1.amd64.deb package from the brother page. After installing this, I can run xsane as root and scan perfectly.
I could not find any instructions for enabling this as a user on 11.04, so I followed the instructions for 10.04 at [URL]...n1c.html#u9.10 and added the following between libsane_usb_rules_begin and libsane_usb_rules_end
Code:
# Brother scanners
ATTRS{idVendor}=="04f9", ENV{libsane_matched}="yes" I then restarted udev, turned my device off and on again and tried to run xsane. I get the following error:
Code: "Failed to open dvice `brother2:bus3;dev1': Invalid argument I looked at what the rules were trying to do when libsane_matched is set to yes, and found that setfacl was not installed on my box. I installed this and changed the line to read
[Code]...
Ubuntu :: Can't Scan For Networks
Sep 1, 2011I updated to KDE 4.7 today with MUCH trouble muon hung at towards the end of the updrade at 100% so i had to force quit with " sudo ksysguard" it refused to boot into the desktop so i had to complete the upgrade from the terminal/safe mode when it finished i could not get my wireless to work my drivers is installed properly and i have tried toggling the wireless switch, much to my dismay but nothing seems to work. i can't scan for networks and the network-manager app just reports "WLAN Interface: Error: Invalid state"
View 2 Replies View RelatedSlackware :: Cannot Scan As User
May 1, 2011Printing (as user) is fine and scanning as root works too, but scanning as user doesn't work. I've had similar problems in the past, but there's something else going on now.This thread doesn't help either.Yes, I'm a member of the scanner group, and like said before: as root everything works fine.
View 2 Replies View RelatedOpenSUSE :: Scan Multiple Pages To Pdf From 11.2
Nov 20, 2009I'm looking for an easy solution (1 click install) to scan multiple pages to one pdf file on openSUSE 11.2 with gnome.Most tools only support 1 page tobe scanned to pdf.gscan2pdf looks like a solution but I can't get it running on 11.2.(missing dependencies e.g. perl-forks)
View 9 Replies View RelatedGeneral :: Scan-to-PDF Software For Linux?
Dec 12, 2010I have a workflow whereby I scan paper documents into searchable PDFs using a Fujitsu ScanSnap S500 document scanner. I am not a great fan of the bundled software, but it's dead simple to use: place a stack of paper at the top, push the green button and a searchable PDF comes out.Now, I'd like to do something similar on Linux (Ubuntu 10.10). The scanner is supported out of the box.I've looked at gscan2pdf and XSane:
XSane looks powerful, but not really suitable as a workflow solution;gscan2pdf is a bit closer to the "push the button, get the PDF" ideal, but still not 100% there.
Ubuntu :: Can't Scan In 9.04 / No Device Is Found
Jan 26, 2010I just bought an hp 6500 wireless printer, and after taking 5 minutes to set it up (amazing how easy it is to get hardware working that supported by Linux) I was happily printing...But- I haven't managed to get it to scan from my desktop pc running 9.04. Tells me no device is found. I added the printer to a laptop running 9.10, and it scanned perfectly straight away...
I've been through the Ubuntu help documentation and haven't found a solution.I think that maybe Turbo Print (for our old Canon printer) might have messed something up. I had to uninstall Turbo Print to get the printer to work (it hijacked Ubuntu's built in printing stuff).