I am attempting to install a WLAN card driver but I'm having trouble with running "make". When I launch it it tells me I need to set the kernelpath, but my problem is that I have no idea where the kernel even is inside of fedora. I'm on Fedora 14.
View 2 RepliesI have a Dell Latitude D800 with a Dell Wireless 1350 (802.11b/g) WLAN miniPCI Card. I need to install wireless on this laptop but I see no wireless card when I know I have the above wireless card. Here are some commands that I ran that I might prove useful:
[Code]....
I have installed Fedora 8 on my laptop. My laptop has a " Network controller:
Broadcom Corporation BCM94311MCG wlan mini-PCI " wireless Card.
I want to get the wireless working. I did an 'lsmod' and I found that the modules for this card is not installed. I tried to start Network Manager, but network manager cannot connect to wireless but it cant. How and where can I get the drivers for this and how do I install those modules. My laptop is a Dell vostro 1400.
I want to install a new graphics card, Nvidia Geforce 9400 GT, into my system running Fedora 12, x86_64.
* Should I install the hardware into the system first?
* Or should I download the proper drivers and install them first, before hardware?
* Do I need to disable or remove drivers for my integrated graphics card (Integrated NVIDIA GeForce 6150 SE graphics) before I do anything?
A few years back I gave linux a try. It was fun but eventually I dropped it because simple tasks like installing software were always a practice in goose hunting and copy/paste command marathons. I am trying again to get fedora up and going. Thinking many of the old methods would be cleaned up by now. I was trying to install nvidia drivers for my 8800 card.
I download the *.run file and it tells me I need to disable "X...etc" so I init 3 to the command prompt and run the *.run file there. Then the installer says.... "hey buddy.. you need gcc to make this work". ok.. I type init 5 to get back to the internet browser. So I search about google for a few moments and then find the yum command for getting gcc installed. Run the gcc and again... init 3 to get back to the command prompt and run the *.rn file for the nvidia drivers. This time the installer says... "hey man... you need the kernel source tree".
[Code]...
installing the PCI wireless card drivers in CentOS linux. I have "Sabrent PCI-G802 PCI Wireless Card - 54Mbps, 802.11g". I tried looking in google and tried multiple ways to install the driver but failed , I have followed the instructions given in the link i.e.
performed the following steps .....
1.# tar xvzf package.tar.gz (or tar xvjf package.tar.bz2)
2.# cd package
3.# ./configure
4.# make
5.# make install
I have the original cd (this cd has linux drivers also) which came with the PCI card but its not a plug and play cd like the MS windows, the cd drive is not reading the disk (But i can open it in windows 7). I copied the installation files from the cd to usb drive on my windows 7 PC and copied them on to the CentOS /home/user directory and performed the above mentioned steps. I was successful in getting till the second step. when i did the step 3 the system is asking some thing about
"Linux kernel source directory [/usr/src/2.6.18-92.el5PAE-i386]: Configure"
I just pressed the enter button and it went to the next message which is
"Linux source tree 'Configure' is incomplete or missing!" Configuration failed
I have been using FC10, it works well with wlan for sometime and goes inactive after some time and hence network goes unavailable. Even after few attempts to reconnect doesn't help. Rebooting helps in bringing it back temporarily.
View 7 Replies View Relatedi have a little experience with ubuntu but i have had bugs that are not resolvable at this time in ubuntu. so instead of giving wild bill back my pc i am looking for a new distro. my concerns with ubuntu revolve around acpi. no fan control and high temp. the 2nd problem that is almost overlookable is the ata1 softreset error. it usually is no problem but occasionally have to do manual fsck to fix. so heres my laptop specs. toshiba a305d-s6848. amd turion x2 ati x1250 integrated. 3gb ram. 500gb hd vista and ubuntu 9.04 dual boot grub with 100gb ubuntu and the rest vista. so q1= what suse version would be best?
q2= is suse's acpi better? ubuntu runs all features but fan control
q3= is suse as easy to install? or harder
q4= ati graphics i know for my card went to legacy what version still has the ati drivers for my card
q5= is suse easier or harder to work with and get everything working.
i know no linux is or opsys is perfect. im just looking for one that is stable and works the pc correctly. i know its a big thing to ask. i know no one can tell me that. but just looking for suggestions. im thinking of downloading suse and does all the downloads support live sessions.
i installed Fedora 12 on an external hard drive. Everything went fine with the installation and it was working perfectly until i tried to install my video card drivers. I have done this many times before and it has worked. I have an ATI card. Anyway after installing the driver i rebooted and now when it starts it show the loading bar on the bottom but then nothing happens its just a black screen!. The worst part is that when i go into windows and my external is plugged in windows wont read it and i have very valuable data on it. I go into disk management and it shows up but windows says that its empty. which is obviously not true because Fedora starts to boot. I really just want Fedora off my external and for windows to read my external with all the files still on it. Is there a way to get by that blank screen?
View 2 Replies View Relatedvery much like everybody i am also waiting for centos 5.3, because 5.2 could not sit on my notebook due to obvious driver issues. would anybody tell if centos 5.3 support my x3100 graphics card and bcm 4311 wlan card?
View 5 Replies View RelatedI just installed a minimal version of Ubuntu 10.10 (with Openbox) over 10.04. Mainly everything's ok, but I have three problems:
1. When shutting down or rebooting, my speakers make a loud pop. Upon googling around, I found this topic on the Arch forums. Running
Code:
Before rebooting/shutting down works. I, however, would like to have this permanently fixed so I don't have to run these commands every time before rebooting/shutting down.
2. I can't install the ATi video card drivers. I downloaded the correct driver (10.9) from the ATi website and made sure I had the packages found here installed. I also made it executable by running
Code:
When I run the installer, using
Code:
I get this output:
Code:
3. When booting, I get a message saying something like "intel_ips can't find i915 symbols, so graphics turbo is disabled". When googling for this, I see this is a kernel related issue. Since I don't have any understandings of kernels, I thought this is a little too high up for me. What does it mean and how can I fix it, as it slows my boot down quite a bit?
when i installed linux 5.0 on my desktop. I had'nt got the eth0 option when i run the neat command. It had'nt taken the driver of lan card at the time of installation. And If i wants to add a new Lan card how to install its drivers.
View 2 Replies View RelatedI need help installing graphics drivers for my nVidia 8600GT.
View 3 Replies View RelatedI use Ubuntu 10.4 or 10.3 (How do I find out)I'm trying to install the drivers for my wireless card (I don't know what hardware I use) I'm running on a Compaq Laptop 6735s and I was told to use this This site tells me to pick either a 32 bit or 64 bit, I don't know which one I am. so I can run off my wi-fi internet?
View 6 Replies View Relatedi came across BT4 last few weeks ago, and i tried it in vmware and was tempted to know more, so now i wanna try to install it and dual boot. Here's my problem, when installing the install.sh i get 2 options instead of 3 options in the partioner, so i couldnt install BT4 without erasing my W7, also if i do successfully install it, how do i install drivers for my wireless card, ohh and my laptop is a Acer Aspire 4736G, my wireless card is a intel(R) WiFi Link 5100AGN...
View 2 Replies View RelatedI installed ubuntu netbook remix (the new version 10),and when I try to install drivers for my network card it says I need an internet connection,when I cant access the internet,I even tried using a wired connection (since I usually connect via wireless),but still its no use. My netbook is the following: [URL]...
View 1 Replies View RelatedI wonder if there is anyone who could install the Wireless card drivers in Backtrack 3? and post where i can download it later?My Wireless card:Intel Wifi Link 5100 AGN( I found a post but i dont understand it and im new whit linux HERE )
View 3 Replies View RelatedWith nearly all Linux distributions (Ubuntu, Kubuntu, and Linux Mint being the exceptions), my system never seems to recognize that my laptop even has a wireless card attached to it. That is, when I run "lspci" the wireless card doesn't even show up on the list like it does with Ubuntu/Kubuntu/Mint. This narrows my options when it comes to choosing a distro to install on my computer. I can't seem to find instructions as to how I can make my wireless card work. I assume it needs a driver. I managed to find the driver, I think, in the form of a .tar.gz file. The card is a Realtek Semiconductor, RTL 8191SEvB Wireless Lan Controller (rev 10).
View 1 Replies View RelatedI'm trying to install the drivers for my nvidia graphics card. I downloaded the shell script from the nvidia website. However, there's something peculiar going on. When I execute the shell script it says it cannot find my kernel headers, yet I can verify that my /usr/include/linux/kernel.h does exist. I have selinux on, but just installed os with it on, so contexts are fresh. Checked them as well. After doing some research I found something out. When I run a 'uname -a' I get this.
Code:
Linux ariel 2.6.18-194.el5PAE #1 SMP Fri Apr 2 15:37:44 EDT 2010 i686 i686 i386 GNU/Linux
Yet when I ran 'yum install kernel-devel kernel-headers' they installed the following versions.
Code:
kernel-headers-2.6.18-238.12.1.el5.i386
kernel-devel-2.6.18-238.12.1.el5.i686
Shouldn't they be
[Code]...
I see that the error in the nvidia shell script can't locate the header files for the RUNNING kernel version which makes sense. Why would yum install that version instead of the one in 'uname -a'? Or am I misunderstanding something?
I have been trying to install fglrx drivers for my ATI card with Debian testing (x86) but without any luck. I have tried what it says here http://wiki.debian.org/ATIProprietary but I only come up with a blank screen (and also invoke-rc.d gdm stop does not work either?) I have also followed the directions at [URL]....html and that doesn't work either (make error 127). I must be doing something totally wrong.
View 6 Replies View RelatedI have onboard Atheros Communications L2 100 Mbit Ethernet Adapter, and I am not able to install the drivers of it. Following is the output of command lspci -v 01:00.0 Ethernet controller: Atheros Communications L2 100 Mbit Ethernet Adapter (rev a0)
Subsystem: Elitegroup Computer Systems Unknown device 2048
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at feac0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at feaa0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
[Code]...
Trying to install drivers for Highpoint Technology's RR2310 RAID card as a data driveFollowing the simple instructions from HT seems to go well. Typeingsudo sh .install.shreturns:The disk you insert is for linux kernel 2.6Update initrd file /boot/initrd.img-2.6.28-11-generic for 2.6.28-11-genericPlease reboot the system to use the new driver module.When I reboot things are as before: no array; the individual drives are fdisked as singles with no partition table.When I check uname -r, I see the Ubuntu 9.04 kernel is 2.6.31-19-generic.In /boot there are initrd files 2.6.28... 11, 15, 16, & 17 and 2.6.31... 16, 17, 19 & 22.The card BIOS shows the array is 'NORMAL' and lspci shows it also
00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)
[code]...
How To install windows drivers for a WiFi card -TEW643Pc card
View 5 Replies View Related[URL] I just updated and then saw this news , whats the solution for me, I either want to go beta or downgrade, If i try to boot to previous kernel, boot hangs in graphic mode, I cant start X and gdm . How to install kmod with beta drivers? Or whats the solution, nvidia ver: 195.36.08
[Code]....
I'm trying to install the drivers for my Wlan card, I've downloaded the drivers in the tar.gz-file from Broadcom and untar-ed it in my /home/<username>/hybrid_wl-folder and cd'ed to it and I try to run "make" but I get an error: KBUILD_NOPEDANTIC=1 make -C /lib/modules/'uname -r' /build M='pwd' make: *** /lib/modules*2.6.31.5-0.1-default/build: No such file or directory. Stop make: *** [all] Error 2
I'm getting really desperate, I need my Wlan on Wednesday. I'm following the README but this is what I get.
I am trying to get the madwifi driver installed on my new ubuntu 11.04 system. I am getting the following error: ./kernelversion.c:13:30: fatal error: linux/utsrelease.h: No such file or directory compilation terminated. Makefile.inc:81: *** Cannot detect kernel version - please check compiler and KERNELPATH. Stop. What is the value of KERNELPATH? I have the following content in /usr/src.
[Code]....
How do I install my driver wlan in Fedora 14? I use this notebook hp:
http://h10025.www1.hp.com/ewfrf/wc/p...reg_R1002_USEN
I have already installed the update of fedora and still does not work.
After having a lot of trouble with vista and no chance of getting Windows 7 anytime soon, I decided to get Ubuntu and use dual booting with vista. I had recently installed it about two days ago and for the most part it worked pretty well. That is until I installed the driver for my video card, an ATI Radeon HD2600 pro, then things went down hill for me. Every time I try and boot Ubuntu it now goes to a black screen after the logo comes up and i am unable to do anything. I have tried to look up some solutions, but I am still relatively new to programing and some of this stuff seems a bit complicated for me. Is there a simple solution to this that does not require a reinstall?
View 9 Replies View RelatedI have ubuntu 9.10 I have the ATI Technologies Inc Mobility Radeon HD 3600 Series [1002:9598]video card. I dont know what it is but i want to enable extra visual effects. unfortunally a message stating "searching for drivers" appears, eventuall folowed by " Visual Effects can not be enabled" i think this is due to the drivers obviosly.
what are the drivers I need for linux (if any) for my specific video card? what do I need to do? also which video card are best fit for ubuntu/ linux? note: I dont know what it is, but originally when I first installed ubuntu I did something and the visual effects had worked had worked and up until recently i may or may not have of messed with any thing could i have of touched something
I have just installed Kubuntu 9.10 in my laptop and it did not ditected my Nvidia 8400 M GS graphics Card I downloaded a driver file
NVIDIA-Linux.x86-19042-pkg1.run to install drivers but when i run it it shows the error error:you appear to be running X server, please exit X before installing.