Fedora Hardware :: Unable To Install Nvidia - Nouveau Doesn't Work
Jul 3, 2010
I have Fedora 11 installed on a system that initially had an ATI 1650 type card. I recently replaced it with a GeForce GT 220. I don't believe there was ever an xorg.conf generated or used with the ATI card. Initially, when I replaced cards and rebooted, I was able to start up KDE or GNOME but with only 2 very low resolutions available(the highest being 800x600). Next I ran Xorg -configure to generate an xorg.conf file. Everything I am seeing in this file seems to make sense. But now, when I startx all I get is a red error box being displayed by the CRT monitor with this message:
Signal Frequency is out of range
FH 30.1 kHz FV 24 Hz
Please Change Signal Timing
The only way I can get my X system back is to go into the xorg.conf file (in the Device Section) and change the driver to vesa. But I still only have 2 very low resolutions available.
I read that the Nouveau Gallium3D driver will work with Nvidia cards in Fedora 13 (YAY!)What I was wondering is this - will the driver work in 12 or will I need to get 13?
ill try to write in english as well as i can.So, my problem is this:Fedora has Nouveau drivers installed by default, and I want to install nVidia propietary drivers.When i try to install Nvidia propietary in runlevel 3, it says that ive to deactivate or unistall Nouveau.
Ok, i do that, but the next reboot, the tty doesnt work (black screen) and i cant access runlevel 3 correctly and i cant install propietary driver. I have looked this in google and i didnt find nothing, so i ask here.
Can this be done similar to some other O/Ses so Nouveau doesn't pre-screw up the kernel for 3rd party drivers??? Would be great in F16 if we were given a choice re: wanting nouveau or not. I simply can not get F14 or F15 to work with the 270.xx drivers on recent equipment.
Nouveau won't go away.I done the rdblacklist in grub and blacklist in modprobe.d but it still persists.Is there something else I need to for Fedora 15?
Only about 1.5 weeks into Linux guys so bear with me. I'm trying to uninstall the Nouveau driver and install NVIDIA-Linux-x86-71.86.14-pkg1.run for my old Nvidia TNT2 card. Following these directions I run into a problem in the first step. When I execute the Ctrl+Alt+F1 command and get:
Ubuntu 10.10 splat-desktop tty1 splat-desktop login: if I enter splat which I believe is my username and the correct p/w I get an incorrect login response.
Nvidia either works or it doesn't work under Fedora 10 64 bit OS. I have re-installed Fedora 10 64 bit and Fedora 11 64 bit 10 times each and it's getting real old. I keep erasing my system because Nvidia doesn't want to work. Leighs post does no good on this issue and neither does anyone else's or else it would work.
this may be asking too much (especially from leigh123, 'cause i know you're working hard), but i've lost track of the current status of the great nvidia driver vs. nouveau driver debate, and what we can hope to see in f13 in about 20 days. could you provide or point us to a layman's summary of what graphics capabilities we can expect with a "default" configuration when we bring up f13?
in particular, can we expect nouveau to provide 3-d for f13 (or in the near future)? nvidia install guides, leigh123, but despite your best efforts, the procedures seem to be getting more involved as time goes on, not less (and not noticably more reliable, either). between graphics card drivers and flash plugins fighting firefox (not to mention adobe fighting videos and hulu) it's discouraging to actually lose capabilities that were once available when upgrades are made.
I installed F11 from the DVD iso. The nouveau driver seemed to work and I could get both monitors working with xrandr.
Then I tried to install the nvidia drivers. I installed akmod-nvidia.
They didn't work. I got this in my /var/log/Xorg.0.log:
Quote:
(II) LoadModule: "nvidia" (II) Loading /usr/lib64/xorg/modules/drivers//nvidia_drv.so (II) Module nvidia: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0
I've just installed Squeeze and try to install Nvidia drivers, but installer wrote that I have to disable Nouveau first. So could you please tell me how to turn off nouveau driver totally and correctly.
Fedora (2.6.34.6-47.fc13.x86_64) I installed that update, during the installation process it said that it had to remove three packages, one of them was kmod nvidia for the old kernel (Fedora (2.6.33.8-149.fc13.x86_64))After the update finished installing the new kernel, I restarted the system and Nvidia did not load. (I assume because Update manager removed the old nvidia? But I also assumed that a new version would be installed automatically?)I received the following Boot messages:
Code:
Entering non-interactive startup Starting monitoring for VG vg_user1: 3 logical volume(s) in volume group "vg_user1" monitored
[code]....
I'm confused, if Update Manager removed kmod nvidia, then why does yum say it is installed? And why doesn't the new kernel update work with that version? Or should I install a driver version for that particular kernel? I've read while searching that I need to install a kmod-nvidia for that particual kernel version and that I should login to my previous kernel until that happens, is that the problem I'm having?
Why don't rpmfusion and fedoraproject release the kmod-nvidia and kernel updates at the same time to avoid problems such as this? Does anyone know how long does it usually take for rpmfusion to release the new kmod-nvidia driver for the latest kernel?
First some specs: Fedora 13 (Goddard) 32-bit NVIDIA GeForce GTX 260
The DVI output on my card works just fine to my monitor, which is what I've been using. I installed no drivers; it just worked. However, now I need a duplicate screen to be given via the s-video output, but it doesn't work. Nothing is being given to the tv and nothing is being detected under monitors. From what I understand, this is because I need to install the appropriate Driver.
I downloaded my driver from the nvidia website, but it won't install. it tells me I need to disable nouveau.
I am using an Nvidia GeForce FX5200 card and nvidia hasn't released a driver that seems to work with it in Fedora 13 yet.. However, I decided to do an install of F13 and use the nouveau drivers until Nvidia updates their drivers, however, the nouveau drivers don't work worth a crap with my card I did a fresh install and then ran a yum update. What I am seeing is after a few minutes, all the icons disappear, no fonts, and nouveau starts throwing errors to my message log. Here are the messages I get:
My system with kernel-2.6.35.10-74.fc14.x86_64, NVIDIA 3800 + Samsung 2233 and 3Dvision kit works fine, but upon upgrading to kernel-2.6.35.13-92.fc14.x86_64 the system won't go past the blue->white bar along the screen. The modprobe.d directory has the file blacklisting nouveau and there is the grub entry rdblacklist=nouveau, but do I need to re-run the nvidia installer. If so I think I need to reset the init level to stop X11 trying to load. and will I need to keep doing this everytime I upgrade the kernel if I have nvidia drivers installed?
I am finding little bits and parts of information about CUDA enabled mplayer/mencoder .. apparently CUDA will enable your Nvidia GPU to do work when transcoding video instead of the CPU?
does anyone know if there are any Fedora RPMs of a CUDA enabled mplayer? how can you tell if your Nvidia card supports CUDA in linux? I found some ubuntu packages but so far nothing for Fedora
I just wanted to check, I'm using nouveau on Fedora 12 with the latest updates and each time I wake the machine from suspend, the fan on my XFX 8800GT goes to full speed and stays there. I've read some nouveau stuff and they say that nouveau doesn't control the fan speed, so I think the card is running in a safety mode after wake up where it runs the fan at full speed to be safe. The only suggestion I saw for fan speed and nouveau was to use nvclock to manually adjust the fan but that sounds dangerous to me. I think I'll just go to the closed rpmfusion driver then if this is the case.
On friday I tried upgrading my kubuntu karmic to lucid. The upgrade failed for reasons I've forgotten... the upgrader said it had run 'dpkg --configure -a' or something, which I assumed meant that it was restoring the OS to a usable state... which it did not and now I have a broken distro.TO THE POINT. I backed up my files and decided to do a CLEAN INSTALL of Lucid.
I've got a "little" problem with fedora 13: dual head with nouveau is not working. gnome-display-properties recognizes two displays and i can configure it (left, right, mirroring, ...) but first display is always in standby. Seems it doesn't get a signal from graphics controller. Desktop seems to work fine (can move the mouse pointer on the other screen into "the black hole"). I use Fedora 13 x86_64.
Although I managed fairly quickly to get 3D enabled on the GF 7600GS of my desktop, it took me longer to get 3D up on the GF 9650M GT of my Asus laptop M70Vn. Although I made extensive use of the numerous procedures outlined here, none of them worked and booting my laptop always ended up with me facing a jet-black screen and a completely inexpressive blinking white cursor. My solution was simple: I did not blacklist Nouveau and problems mysteriously disappeared.
I have just upgraded from Fedora 11 to Fedora 13 and now can't get my two monitors working as a single "screen" (it worked under F11). I have a GeForce video card with two monitor outputs
I then edit the xorg.conf to change the driver from nouveau to nv and I can start X and the LCD displays the desktop at a resolution of 1680x1050 (good) but the CRT just displays random blocks of colour. At this point I also get a kernel crash - see dmesg output attached, but the system is then OK to use. I have tried editing the xorg.conf to add a second monitor and a virtual screen resolution to match the two monitors (1024x768 + 1680x1050) combined (2704x1050) but still only the LCD monitor works, but with the virtual desktop that can be nudged around with the mouse. I would like to get back to using both monitors with a virtual screen across the two monitors.
I have two monitors - one connected to the VGA port and the other to the DVI port. Fedora seems to be detecting both monitors (figured this out because when I rotate the desktop cube, the second screen is also seen.). However, the monitor on the DVI port is blank. This happens even if I use just one monitor with the DVI port. I cannot install the proprietary nvidia drivers because my computer hangs (has been happening since fedora 11 or 10), Is there a way to get both monitors to work with the nouveau driver?
I faced this problem in Fedora 13 as well and was hoping both screens would work out of the box in F14. Is there any way I can do this to make it work like nvidia's TwinView?
It does this all the time whenever I reboot and I hadn't rebooted my PC in months simply because it's a GOD DAMN pain to figure this crap out. I need a REAL fix.
My computer turns off and boots, it goes directly into Recovery Menu. It refuses to boot normally. I load low graphics mode, it doesn't even let me make changes to the configuration file, OR let me have ONE session in low graphics mode. I've tried reconfiguring xserver, re-installing nvidia drivers, STILL the same effing garbage. It's starting to **** me off. I'm mostly a Linux noob, and I hate trying all these "tips" that don't work to make my stupid display work. I use gnome. Any advice, tips whatever to make this work? If you need something, I'll try my best to get it but I'm on my other computer right now so displaying my configuration files will be a pain. :/ Before I installed vesa, low graphics mode wouldn't work because it said the vesa module didn't exist and it also said no screens.
on my old fx 5200 nvidia card, I installed the 173 driver and now when I log in to Default Ubuntu desktop with 3d enabled, like my screen will flash on and off like the panel and my awn dock turns white and then returns to desktop and repeats. You can only see the wallpaper and thats it. Useless! My desktop is virtually useless because I can't even use it. Gonna have to reinstall Ubuntu for the 5th time!
Now that nVidia is up and running, I'm curious to do a comparison with Nouveau. I there an EASY way to do this? Like a simple on/off switch? Major system/kernel changes are not an acceptable option. If it can't be easily done, I'll just stick with nVidia.
I've experienced the great functionality that nouveau gives me, but am a bit disappointed that it cannot support 3D acceleration. I play a few games so this is a requirement.I don't want to switch completely back to the NVIDIA driver because it breaks my brightness control keys on my laptop, and it isn't as fast and responsive as nouveau.Is there a way to have nouveau run by default, but when I launch a game in a separate X server it would load the NVIDIA driver?
I have problems with xrandr in a system with Nvidia GeForce 8600GT video card. I want to use xrandr to rotate the screen on the fly.
~:$ xrandr -q xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 175, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 50.0* 1600x1024 51.0
[Code]....
I tried enable the last option, change values for xinerama and twinview, but nothing works.
After installing 11.3, I realised that my graphic driver is not working as desired. I have a Compaq CQ60-430SA laptop with an NVIDIA 8200M graphics card. Earlier with 11.2, I had some proprietary NVidia drivers and my graphics were smooth. However, I am not getting the same performance with Nouveau...
As can be seen from the screen clipping below, the images especially in the preview mode and the icons look jarred (highlighted in red). I have no complains with the video but the images and icons do look shabby at times and therefore I want to switch over to the proprietary NVidia drivers.
