On friday I tried upgrading my kubuntu karmic to lucid. The upgrade failed for reasons I've forgotten... the upgrader said it had run 'dpkg --configure -a' or something, which I assumed meant that it was restoring the OS to a usable state... which it did not and now I have a broken distro.TO THE POINT. I backed up my files and decided to do a CLEAN INSTALL of Lucid.
View 3 RepliesI have Fedora 11 installed on a system that initially had an ATI 1650 type card. I recently replaced it with a GeForce GT 220. I don't believe there was ever an xorg.conf generated or used with the ATI card. Initially, when I replaced cards and rebooted, I was able to start up KDE or GNOME but with only 2 very low resolutions available(the highest being 800x600). Next I ran Xorg -configure to generate an xorg.conf file. Everything I am seeing in this file seems to make sense. But now, when I startx all I get is a red error box being displayed by the CRT monitor with this message:
Signal Frequency is out of range
FH 30.1 kHz FV 24 Hz
Please Change Signal Timing
The only way I can get my X system back is to go into the xorg.conf file (in the Device Section) and change the driver to vesa. But I still only have 2 very low resolutions available.
Can this be done similar to some other O/Ses so Nouveau doesn't pre-screw up the kernel for 3rd party drivers??? Would be great in F16 if we were given a choice re: wanting nouveau or not. I simply can not get F14 or F15 to work with the 270.xx drivers on recent equipment.
View 10 Replies View RelatedI was trying to install Ubuntu 10.10 using a dvd onto an older pc i have. Specifically the pc has 512mb ram, 160 gb hdd, intel pentium 4 2.93ghz. The first time I attempted it was working just fine, then during the setup while i was entering region info the window went away and the computer shut off. I restarted it then retried the installation and got the error message "Medium does not contain live file system". I found a different type of cd and attempted to reinstall again. Now the error message says that it could not mount the cd probably because the cd is not in the drive.
View 1 Replies View RelatedI made an xubuntu disk.loaded it and rewrote my hardrive.on a pretty old averatec laptop. 3/4 of the install it gives a a io error and stops the install.I tried to reinstall from the screen again but got the same error.So I rebooted and it skips everything and goes straight to a grub loading stage 1.5, grub loading error 17. It even skips the live cd.I also tried to do it thru a usb stick but that gets ignored too.
View 3 Replies View RelatedI have tried both DVD and CD (both are MD5-checked) of both Lenny 5.0.8 and Squeeze RC on my HP DV7-3074CA. (a.k.a 3085DX)When I choose a graphic install, it just hangs after loading the initial files.When I choose the normal install, It gives the following error:
[1.383207] ACPI: EC: Input buffer is not empty, aborting transaction.
Is there a boot command I can input to override this? I tried removing the battery slot, but the only difference is that that message does not appear, but the setup hangs anyway.
UPDATING:Tried "pci=noacpi" but that did lead to a kernel panic.[1.547564] Kernel panic - not syncing: Attempted to kill init!
I have installed openSUSE 11.4 from live DVD.. The Installation screens appeared to display properly in my TV. However , post installation , the display is completely gone , there are only horizontal stripes displayed. Then I rebooted to Failsafe mode and I was able to see a workable screen ...The problem again is that the fonts are too small and not at all legible. I am able to see that SUSE has identified the Nvidia Driver and identified the TV and the resolution.. But I want to change it to a more bigger resolution..
I thought I could remove "nouveau" and set the display to "Xvesa"...How do I do that?? On terminal I am trying to kill the nouveau processes and giving rmmod nouveau , but not successful. How do I cahnge to a better resolution? Maybe 1280*1084 or 1280*768?
I'm trying to install 10.10 but it keeps throwing an error. I'll include the error and log file below:
An error occurred: Permission Denied For more information, see the log file: c:...
I had dual screen config (large desktop) going on 11.2 with proprietary nvidia driver without problems. After upgrade to 11.3 this didin't work. I was not able to find a way to configure nouveau drivers, and it was stuck in the 'twinview' mode, so decided to install binary nvidia instead (the 'hard way'). Took me a while to figure out 'nomodeset' thing, but in the end drivers were installed successfully. The problem now is that only monitor displays anything, and I can't find the nvidia control panel to activate second monitor and extend the desktop there.
Used to be able to install nvidia control panel easily in 11.2 with one-click install, but for 11.3 the page says that the one-click install buttons aren't ready yet (SDB:NVIDIA drivers - openSUSE) So my question is 'how to get dual screen going and extend my desktop to second screen using 11.3 and nvidia 210 card' ? And I don't care whether it's nouveau or proprietary drivers, as long as it's easy to configure and it works.
I'm trying to install The Sims 2 (which I'm aware currently does not run properly in wine anyway), using the multi-CD version. The installation goes normally, up until it comes time to switch from disc 1 to disc 2. The installer prompts me to insert disc 2, but it seems that Ubuntu still believes that the installer doesn't want me to open the drive, because, when I try to open it, it doesn't open, and a window pops up with the following message: Unable to eject CD-RW/DVD RW Drive DBus error org.gtk.Private.RemoteVolumeMonitor.Failed: An operation is already pending
View 3 Replies View RelatedRecently I bought the next notebook: Asus R510JF-DM020 i7-4720HQ
My hardware (extend ouput):
Code: Select all$ inxi -Fzx
System: Host: Asus-R510JF Kernel: 4.2.0-1-amd64 x86_64 (64 bit gcc: 4.9.3)
Desktop: KDE Plasma 5.4.2 (Qt 5.5.1) Distro: Debian GNU/Linux stretch/sid
Machine: Mobo: ASUSTeK model: X550JF v: 1.0 Bios: American Megatrends v: X550JF.203 date: 04/02/2015
CPU: Quad core Intel Core i7-4720HQ (-HT-MCP-) cache: 6144 KB
flags: (lm nx sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx) bmips: 20751
[Code] ....
I am trying to dual boot Vista and F10 and I have 2 different 400GB hard drives to do it on. On the first HD, I have Vista installed but when I try to install F10 on the second, I get this error message:
Quote: Error: Unable to read group information from repositories. this is a problem with the generation of your install tree. I've looked it up and found some forums but none answer how to "fix" it (if it is indeed something that you fix).
I'm doing a Kickstart install of Fedora 11 with a DVD ISO as the installation source and the ks.cfg file in the root folder of the DVD. The error message I get is: "Unable to read group information from repositories. This is a problem with the generation of your install tree."
View 3 Replies View RelatedI have tried everything I can think of to install the nouveau driver, which is the only one I can trust on my system with the Geforce 8800 card I received as a gift. I tried Nvidia direct download drivers before and it was impossible to alter the screen resolution and the "fixes"/patches were not able to correct that fact. And removing it led to my having to reinstall my system both times. So I'm done with those.
I realized that I could use the nouveau driver when I realized that the second OS on my dual boot system worked perfectly with it. It has the nouveau driver onboard. That OS is Ubuntu 10.04, btw. Also the system I want to install this driver on requires a screen resolution of 1280x960. The Ubuntu is at 1280x1024 for some reason, with the same monitor, it works.
How do I get my stable debian system to download the xserver-xorg-video-nouveau and meet all its dependencies without breaking my system? I even tried reloading Synaptic with the highest available software, but I still could not get the driver to install. What am I doing wrong? Is it just impossible to install this particular driver on my system? And if there's an old version of it I am willing to try that too.
I upgraded from 9.10 to 10.4 this morning on my Dell Precision M2400 laptop. When I rebooted I got a half-black screen with lines. The top portion had 3 miniature login screens also with lines across and too tiny to see anything.I looked at my xorg.conf. It had this in it:
Code:
Section "Screen"
Identifier "Configured Screen Device"
[code]....
I need to use the proprietary NVIDIA driver instead, but it can't install while this is active. I'm working off a fairly fresh install anyway, so I can reinstall debian if the option to not install nouveau is present somewhere during the install process. Or, is there an easy way to get rid of Nouveau from my current install altogether?
View 5 Replies View RelatedAs I mentioned before, I has having freezes while installing F12 (x86_64) with a GeForce 8600 GT. I was able to complete the installation by doing it with the "basic" video driver. However, I was still getting frequent freezes. I installed the testing Nvidia drivers, and the freezes went away. When it froze, it was a hard freeze -- it wouldn't respond to CTRL-ALT-DEL or SysRq (I did enable SysRq first). I had to do a hard reset.
View 7 Replies View RelatedI had to install Ubuntu 10.10 5 times before the boot problem was fixed, but only now to find that the Nvidia GE Force 3 Ti200 video card is NOT supported by the current Nvidia drivers and the legacy Nvidia 96 video drivers has a known bug which may never get fixed.Currently I am running the 1024 x 768 screen size under Nouveau, but how can I change this to 1920x1080 ? Will creating an xorg.conf file work?I did have the GE Force 3 supporting the new 1920x1080p monitors under VGA mode and the screen looked fantastic in the past.
View 1 Replies View RelatedThe problem with X not starting up started after I upgraded kernel from 2.6.38.6-26.rc1.fc15.i686 which is what the FC15 came with. Before that I had X, without installing the nvidia.com driver (whatever came with the stock FC15-XFCE spin).I tried booting the old kernel and at first it worked but X again would not run. Now, after, above operations (reinstall of kernel-devel + kernel headers and all dependencies like glibc-common, glibcs-headers, dkms, gcc..) booting the old kernel does not work anymore: the framebuffer animation of the Fedora logo fillingup freezes at some point almost at the end; HD LED blinking hard. Maybe this means fsck is running and I need to give it more time..? I'll leave it booting when I go for lunch and see how it goes...
View 5 Replies View RelatedI cannot install Kubuntu (or Unbuntu) 10.4 on my husband's computer. I have spent 5 hours on this and cannot get anywhere. I am deeply frustrated. The iso I burned to CD is good (works on 2 other computers). His computer will not boot from USB, no matter what I do to the drive order in BIOS. After loading the blue screen with the Kubuntu logo on it (and the blue-white dots), the screen changes to black and shows the following text:
BusyBox v1.13.3 (Ubuntu 1:1.13.3-1ubuntu11) built-in shell (ash) (initrafs) Unable to find a medium containing a live file system.
He really needs to get rid of WinXP. Kubuntu is what I have on my computer (and love it!). Here is some info about his computer:
OS Name Microsoft Windows XP Home Edition
Version 5.1.2600 Service Pack 3 Build 2600
OS Manufacturer Microsoft Corporation
[code]....
Just downloaded the x86_64 iso, copied it to my USB stick and added a grub4dos entry for direct booting.
Code:
title Fedora 15 x86_64
find --set-root /linux/fedora64.iso
map /linux/fedora64.iso (hd32)
map --hook
chainloader (hd32)
[Code].....
While it does mention nouveau, and I do use Nvidia graphics (PCIe GT 240) I believe the cause may be something else. Googling around leads me to a couple of forum threads that seem to relate to the core series of Intel processors, but I'm at a loss. I've also searched this forum however the search seems to either bring up every result under the sun and non seem to apply or no results at all. I know the card's supported as Ubuntu works flawlessly. I also tried booting in safe graphics mode, however the exact same thing happens.
I doubt using a USB stick in this manor would cause this problem, but if you suggest it i'll install from physical media.
I would post logs, however the shell it drops to seems to be severly limited (lacking reboot, even).
I'm having an issue when I'm trying to install SuSE linux onto my desktop.I go through all the steps and everything looks okay, but when it starts to install the packages, I get an error message that basically says:kernel.desktop - unable to install, exit status 127.I have a ATI X1950 video card in the computer, as well as a AMD 64 FX CPU in the system.
View 7 Replies View RelatedI've just installed Squeeze and try to install Nvidia drivers, but installer wrote that I have to disable Nouveau first. So could you please tell me how to turn off nouveau driver totally and correctly.
View 6 Replies View Relatedill try to write in english as well as i can.So, my problem is this:Fedora has Nouveau drivers installed by default, and I want to install nVidia propietary drivers.When i try to install Nvidia propietary in runlevel 3, it says that ive to deactivate or unistall Nouveau.
Ok, i do that, but the next reboot, the tty doesnt work (black screen) and i cant access runlevel 3 correctly and i cant install propietary driver. I have looked this in google and i didnt find nothing, so i ask here.
Nouveau won't go away.I done the rdblacklist in grub and blacklist in modprobe.d but it still persists.Is there something else I need to for Fedora 15?
View 7 Replies View RelatedI installed the nvidia driver from the vendors homepage. But since it does not support regulation of brightness (and the display is that bright that I want to downlevel it), I wanted to go back to the default display driver which is the nouveau driver.So I uninstalled the nvidia driver and then I realized that I didn't make any backup of the xorg.conf file prior installing the nvidia driver. Shame on me, yeah.Now when the x-server started, it couldn't find the nvidia driver. Okay, fair as it was removed. Next to that my keyboard becomes unresponsive. That's really aching as I can not switch to a text-based console any longer.I'm able to boot into initmode 3 by editing the kernel parameters in the boatloader. I'm also able to edit the xorg.conf with vi in the shell then and start the xserver to test things by calling xinit.
I already tried to recover a bit from this situation by removing the references to the nvidia driver and replaced it with some information I could find on the nouveau homepage - but no luck so far, keyboard still freezes and login window does not appear. I could take a look into the xorg.0.log which warns me about the keyboard getting disabled but I do not really understand why. Next to that I find some other additional information. My computer experience is quite okay, but I'm somehow new to Fedora, I started half a year ago with Fedora 13 on my other laptop which worked like a breeze.
I wondered where I can find information about how to configure the xserver in the default configuration, if there is some reset functionality or so, that brings me back to installation defaults. Those worked ok for the nouveau driver. Unfourtionatly I was not able to gather the correct package name that would probably had helpded me by removing and installing it again.Next to fixing my setup, I had another idea as this is a quite new install to just re-run the install again on to that machine. Is this possible with keeping the files in my homedir?
My system with kernel-2.6.35.10-74.fc14.x86_64, NVIDIA 3800 + Samsung 2233 and 3Dvision kit works fine, but upon upgrading to kernel-2.6.35.13-92.fc14.x86_64 the system won't go past the blue->white bar along the screen. The modprobe.d directory has the file blacklisting nouveau and there is the grub entry rdblacklist=nouveau, but do I need to re-run the nvidia installer. If so I think I need to reset the init level to stop X11 trying to load. and will I need to keep doing this everytime I upgrade the kernel if I have nvidia drivers installed?
Leigh123linux desired code output is below
***
abrt-addon-kerneloops-1.1.18-1.fc14.x86_64
kernel-2.6.35.10-74.fc14.x86_64
kernel-2.6.35.13-91.fc14.x86_64
[Code]....
I cant able to install dansguardian I get the following error..
karthick@Learners-desktop:~$ sudo apt-get update .....
Reading package lists... Done
karthick@Learners-desktop:~$ sudo apt-get install dansguardian tinyproxy fireholReading package lists... Done
Building dependency tree
Reading state information... Done
The following extra packages will be installed:
aggregate
The following NEW packages will be installed:
aggregate dansguardian firehol tinyproxy
0 upgraded, 4 newly installed, 0 to remove and 1 not upgraded.
Need to get 727kB of archives.
After this operation, 3609kB of additional disk space will be used.
Do you want to continue [Y/n]? y
Err http: [URL] aggregate 1.6-4
403 Forbidden .....
I had installed my NVIDIA 9500GT driver on my fedora 13 by disabling nouveau, so should i enable it back after installing NVIDIA driver?
View 2 Replies View RelatedBeen trying to fix this problem myself the last day or so.After trying to create a back up on thursday which failed due to lack of space [followed thishttp://ubuntuforums.org/showthread.php?t=35087]I also think that i had run the update manager and installed updatess i know that i removed some of the default games as well.Booting up my laptop on friday morning i recived this error message"Install errorThe configuration defaults for GNOME power manager have not been installed correctly.please contact your computer administator"The login screen is now in a low graphics mode and when i try to login the screen goes black with some text in the left hand corner which is impossible to read as it only flashes up for a second and i am returned to the login screen.
View 5 Replies View Related