Fedora Hardware :: Cannot Print One Page From Front Panel Of Printer
Mar 9, 2011
I am using F14 Laughlin on my laptop HP Compaq6715b AMD turion 64x2. Installation went fine, only problem is with printer LQ680 24pin series. It is not a real problem that printer want print, it just want print 10 or 15 or 20 pages from tractor bin. I get message: '/usr/lib/cups/filter/rastertoepson failed. It stopped printing after every page, send message, I have to cancel error message, then I can print again. All this is happened if I try to print one by one page from front of printer, I just have to print page with command <ctrl>P.
I've recently installed F15 LXDE RC from the livecd and connected my USB Brother All-In-One MFC-5440cn printer. After following the Brother installation page, the Cups & LPR drivers are installed but when I'm in the cups page (http://localhost:631/admin), the printer will not print a test page or print from any application. The LCD panel on the printer does show 'receiving data' but nothing comes out. The last version of Fedora I had running was F13 and the same printer worked fine.
Are there any other printer drivers I need to install besides the Brothers? The printer does show up in the Print Manager but nothing prints. I did have this same type of issue with Mageia Beta 1 and ended up installing a2ps, which wasn't included in the original print drivers, and it is now printing. So I had to install a2ps with F15 but still no print output. Something must have changed with the recent distros causing this. After looking at the output of dmesg I see this:
Code: WARNING! power/level is deprecated; use power/control instead [14.867397] udev-configure-printer[587]: add /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2/1-3.2:1.0 [14.867991] udev-configure-printer[587]: parent devpath is /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2 [14.869115] udev-configure-printer[587]: Device vendor/product is 04F9:016D [14.880470] udev-configure-printer[587]: MFG:Brother MDL:MFC-5440CN SERN:- serial:BROM5F412304 [14.880520] usbcore: registered new interface driver usblp [15.902920] udev-configure-printer[587]: failed to connect to CUPS server; giving up .....
Any idea why it's failing to connect to Cups or any idea how to find out? Is it possible to have too many USB devices connected? I'm using a 4 port usb hub in use and also using a usb mouse/keyboard connected.
I have a FC11 box, with an HP prineter attached. I trying to print from my laptops after I have setup samba and shared the printer , It was working fine when I was installing FC4 and FC5. I am not sure what is missing. when I tried to print from the XP box I got "Test pge failed to print" error.
I have a couple of large-format printers (Epson R2400, HP 9650) which I only use infrequently. If they are not used very often, they dry out, the print heads get packed up, it's an expensive mess to deal with when times comes to run off some prints. The printers are physically connected to a Windows machine to which my Ubuntu computer is networked.It would be helpful if there was a utility that could initiate a test page print job on the machines, which could be scheduled to run once a week or so. I've had no luck finding such a thing for Windows
I just installed a Brothers HL2170W printer on my desktop which is running Ubuntu 1004 I had no problem with the install and it is working. The problem is when I send a page to print it takes 5 minutes before it prints. Does anyone know if this is normal or if there is a fix. I have the printer connected with a USB cable.
I am running 9.10. I have a HP Photosmart 7350 printer. I have it installed and printing. But the issue I am dealing with is that it will print a full page and then print a blank page..then a full page..then a blank page. Actually they aren't completely blank..it shows half of "2 of 6" or whatever page it is on. Like it cuts that in half and prints the 2nd half of "2 of 6" onto a separate new page.
I have small sound issue - no sound on front panel and headphones are greyed out in alsamixer. This issue appeared after i installed new video card (New video card also adds a pseudo audio device "HDA Nvidia" (without any controls in alsamixer).
I initially had a problem accessing the CUPS interface (see my other post) and got that resolved by adding the user "cupsys". Now, everything "looks" ok, and when I print a test page, it shows it as completed (in CUPS). However, the page never prints. The printer is a Canon MP600 (using the canonmp600en.ppd file to configure it). Here's the output of my conf file.
Code: # Show troubleshooting information in error_log. LogLevel debug
I cannot print pdf files. I have tried using okular and xpdf. The documents display in the program, but print preview shows a blank page. The printer then sends out blank pages. I have tried printing on 2 different printers using usb cables. Using terminal to process the commands shows error:
I have a lpt printer installed "hp officejet t65" when I print a file all the time on the top of the page appear the path of the file where is stored in my pc and and page 1of x. how to wipe off this information when printing a file.
Not sure when CUPS started acting up. I have the latest 13.1 current software installed.The first page to print is always OK, but all succeeding pages are overwritten. The second page shows the first page on top of it, and the third shows the preceding pages on top of it - and so on. Has anyone else seen this problem?I guess the printer buffer is not getting flushed correctly. If my configurations were trashed in some way, I don't know where to look for a fix.
Opened with Gimp multi - page document. It opens fine and gives the layers! When I do : File, Print to File, pdf it gives out only one page! How to get all pages out?
Also when gimp loads all pages they are in layer! Is there a way how to see everypage without swiching written text off to see the next page. Because for mee its
Now if Im here and want to see again stage in y, I need to swich off all layers from y to z? It's normal or is there a way how to see all that in different way?
I have been searching for an answer to this, and have come up dry.
I have an HP OfficeJet Pro 8500 a909a. It was working fine until recently. Now when I go to print duplex, the second page is mirrored vertically and rotated wrong.
I suspect that a recent update to HPLIP has caused this, but there may be something else in play with the GS utilities also. The problem is that I have no idea about how to fix this. I was hoping an update would show up and a simple "yum -y update) would fix things. That still has not happened.
I am a student and would like to save paper, at least with my draft copies, but this makes duplex printing impossible.
My wife has a canon MP470 printer and running ubuntu 10.10. I am able to print black and white, but unable to print photos. I got it to work using another driver, but not the 'correct' one for this printer. I have searched a bit and don't see anything about ubuntu 10.10, just older versions. Or should I just network her to my printer....?
I just installed a copy of Ubuntu 11.04 yesterday on a spare computer. I'm having trouble getting the front panel of my Creative X-Fi Fatal1ty to work. The sound card works just fine when I plug my headphones into the analog stereo output in the back. I'm not trying to do anything fancy with it right now like digital optical out or anything, just trying to get the one analog output on the front panel to work so I can plug my headphones in up front and leave the speakers plugged in the back.
Yesterday I installed FC13.i636, Gnome 2.30.0, on my Dell Latitude D505 laptop. Fresh install from live CD, single partition. Installed all 400+ recommended updates last night. System is working *very* smoothly.I want to print (wireless connection) to my Canon MP160 printer, which is attached to my WinXP machine, and is set as a Shared printer in WinXP. I can print to it fine with my iBook.I used the System/Admin/Printing app to set up a networked printer, letting the app "find" the printer. Printer now shows in the app as:
lpd://192.168.1.108
I choose the appropriate driver and tried a test page. Test page job results in queue showing job "processing" but nothing comes from printer, even ten minutes later. Printer properties show:
I have a rather ancient HP LaserJet printer that was working fine in fedora 14, but when I upgraded to Fedora 15, I can no longer get this printer to work. The printer's front panel reads "LaserJet 5P", but when I print out a test page, it's a "LaserJet 5MP". The printer is connected to my computer's parallel port, and it's capable of understanding PostScript, and I usually don't have any problems printing to it under various operating systems.
The following error comes and goes under the KDE print manager: "Printer 'LaserJet_5P' may not be connected." CUPS reports the following printer state: "Processing - Printer not connected; will retry in 30 seconds..."
I have double-checked that my printer is indeed powered on and connected. And the following lines appear in the error log: W [29/May/2011:18:03:02 -0700] no access to /System/Library/ColorSync/Profiles/sRGB Profile.icc W [29/May/2011:18:03:02 -0700] no access to /System/Library/ColorSync/Profiles/sRGB Profile.icc W [29/May/2011:18:03:02 -0700] no access to /System/Library/ColorSync/Profiles/Generic CMYK Profile.icc W [29/May/2011:18:03:02 -0700] failed to CreateProfile: org.freedesktop.ColorManager.Failed:profile object path '/org/freedesktop/ColorManager/profiles/LaserJet_5P_Gray__' already exists .....
The first three warnings are regarding file paths that one would expect in an Apple OSX system. The "bad request" error is troublesome, because it indicates that either my browser or some configuration software on my system is sending garbage to CUPS. The last two errors occurred when I tried to use the KDE print configuration tool, which was not smart enough to ask me for the root password, which CUPS needs. By the way, the device URI is "parallel:/dev/lp0". Is this still the correct URI?
Getting sound out of the back ports just fine. Using an ASUS P5N73-AM motherboard and a fresh install of 10.04. Everything else works perfectly except the blasted front panel headphone port.
After a recent hardware upgrade, I'm no longer able to use the front panel audio ports on my Antec P180 case. They worked fine before with my old ASUS motherboard, but with my new MSI 870-G45 motherboard I can't get them to work for some reason.
I checked out this thread, [URL] but didn't see much in the way of problems/solutions with front panel audio ports, but it's a lengthy thread so maybe I missed it.
I am trying to connect to a network printer Dell 3110cn from Fedora 14 x64. Till a few days ago, everything was fine. However, over the last few days, I am unable to print anything using my old settings and I am unable to print even if I delete the printer and reinstall it.
During setup, Fedora is able to connect to the printer and I am able to install the drivers and everything. But, when I print something (even the test page), I get the error message "Unable to write print data - Broken pipe'.
I have searched online quite a bit about this problem. Most suggestions were to look if the printer status was "Idle - Ready/Accepting Jobs" since the problem in those cases was that the printer status was "Printer not ready". But in my case, the printer is recognized but unable to print.
my 64 bit XP/fedora 12 box prints fine to a shared printer when I am in XP. The HP color lasterjet CP1215 printer is hosted by a 32 bit vista machine. I can located the printer on the network from Fedora 12 using the add a pinter utility, but I cannot print. I get no error message on the linux machine, but the "submitted " dialog box never goes away (not sure if it is supposed to go away). On the vista machine in the printers dialog box it says "remote downlevel document" in the document name section and "0kb" in the size section, then goes away. the printer does not make any noise.
I am trying to set up printing on my Fedora 14 laptop, on my home network.
Details:
- Home network, single subnet, the desktops are connected to the switch portion of my Linksys via Ethernet and all have static addresses. Name resolution between them is via hosts file entries. The router is running wireless (WPA2/AES/DHCP) to accommodate my laptop which is dual boot XP Pro and Linux Fedora 14.
- The printer is an HP Deskjet F4180 printer. It is attached via USB to a Windows XP Pro box and shared. The XP box is wired and static ip.
- I am able to see all the shares and print to the shared printer from any of the Windows boxes, wired and wireless, including my laptop when I run Windows on it.
- My Fedora 14 is working fine on wireless, using Network Manager and KDE desktop. I am able to access all the Windows shares on both of my wired desktops. One desktop is XP Pro, the other is Windows 7.
This is what happens when I try to set up printing on Fedora:
- I go to Administration / Printing and click to Add a Printer. - I am prompted for the root password twice, which I put in. - I select Network Printer / Windows printer via samba and click on Browse... - It finds my WORKGROOUP and machine name mig29 and prompts for user ID and password which I type in.
[code]....
the user ID and logon on Fedora is different from the one on Windows. During setup I am prompted for credentials. It seems to me that somewhere down the line Fedora supplies not the credentials I supply but my local user ID and password and it obviously fails.
I have openSUSE 11.4 KDE version (64-bit) on a desktop PC. My sound card is ASUS Xonar DX 7.1 (PCI-E). I am brand-new to the Linux experience. I get audio out to my speakers which are connected to the jacks of the rear I/O panel of my PC. I do not however get audio out to my headphones which are connected to the jack in the front panel. I know that the headphones work fine because they do so when I boot up in Windows XP. Here is what I discovered so far: KMix does not show that I have a front panel audio channel. But when I run AlsaMixer it does show that I have such channel and, upon manually turning the volume on, I do have sound out to the headphones.
Therefore, I deduct that I have some sort of configuration problem with KMix and would like to fix it as I prefer to use the GUI interface instead of the AlsaMixer one. It's just a matter of preference! I would like to troubleshoot things using the Audio Troubleshooting guide (SDB:Audio troubleshooting - openSUSE) but I notice that openSUSE's version 11.4 is not mentioned in it. Should I follow the instructions for version 11.3 or wait for an updated guide?
my net worked HP printer will not print-broken pipe - this started after I had to switch off the printer at the mains in order to attend to a paper jam. Now it will not print apart from a test page. I am using Fedora 10 and the device info is "hp:/net/Officejet_Pro_L7500?ip=192.168.0.4"
I have a FC12 machine installed with CUPS and a CUPS-PDF printer. Printer are shared and works fine with this URL:
[URL]
I have both client machine Windows XP and Windows 7. Both has setup the above printer and print fine without any problem. I can get the PDF file from windows test print. The only problem is I face is wait for around 20 seconds for printer dialog prompt out when I press print button in Windows 7. However, my windows XP never t have this problem. The printer dialog prompt out immediately when I press print button.
F13 showing that Canon s100 printer is founded, installed drivers and everything seems to be OK. But when i try to print text, testpage of what ever, nothing happened. Installed system-config-printer 1.2.4-1.f13, same udev and libs. Cups 1:1.4.4.5.f13, libraries, php modules Here is the Error msg:
Linux and I have trying to get my Fedora 15 (x86 64bit) on my laptop to print to an Epson Stylus NX515 printer/scanner. I have the printer connected to a router through a wireless connection. I have other computers that are on the network that are Windows based and they of course are printing/Scanning just fine. The printer is located in a different room. I have been searching for a solution but non that explains how to install a printer driver for one that is connected to a router wirelessly.
Our one remaining problem seems to be printing. She has an HP OfficeJet 6500 USB printer. We have the computer conntected. Strangely, when I boot from the CD the printer shows up as installed even though I did nothing to install it. After having submitted a print job it shows the printer status as "idle" and the print queue is empty. I tried deleting that printer and re-installing. The installation went as one would expect. However the results are the same. I'm beginning to think that somehow the problem is related to the fact that we are operating from the live CD. getting this thing to print from the live CD.
