I have a fedora 13 rc3. The problem is that boot the system stops here Starting libvirtd daemon
Prior to that, stop at this point registering binary handler for windows application. I got up to enter the
tty2
to remove Wine
This time to stop here Starting libvirtd daemon
I've followed this guide [URL] after rebooting the system hang at:
starting ati external events daemon [OK]
This line start blinking for a while, then nothing happen. I am using a radeon hd 4225. (I'm booting with acpi=off).
I have done a fresh text-only installation of Fedora 10 on a Dell Dimension E521 for the purpose of setting up a server. After installation I ran yum update to bring the system up to date. After the update, I rebooted the computer, but the boot process froze. I recycled power and pressed "I" after the Dell BIOS screen and the GRUB bootloader appeared. I selected the most current version, edited the kernel line by deleting "rhgb quiet" and replacing it with "3." After making this change, I continued with the boot and the computer stopped at "Starting udev:" I have two fedora 10 revisions showing in the GRUB bootloader, the original installation and the update after running yum.
I repeatedly tried rebooting both versions and, after about 30 attempts, the computer finished booting and got me to the command prompt. Reading through the forums indicated there might be some issue with my nVidia GeForce 6150 onboard video and fedora 10. So, when I got to the command prompt, I followed the instructions in the forums [URL] to load the rpmfusion drivers. This appeared to be successful and when I looked at /etc/X11/xorg.conf it appeared to be correct for the new nVidia drivers. After loading these new drivers I tried rebooting. Unfortunately, I have been trying now over and over to get back to the command prompt, but simply can't get past "Starting udev."
On my virtual server I had the same issue within the last three month. The postfix daemon stopped working suddenly and I don't know why. I can restart postfix normally and it's working normally for a couple of weeks until the next crash. Does anyone have the same problems with CentOS 5.6 and postfix?
View 4 Replies View RelatedI've apparently messed up something I guess with the rc.M file. When I boot the system it goes to
Code: Starting HAL Daemon: /usr/sbin/hald --daemon=yes
and it freezes.
my fedora 10 booting stops at starting udev for 5-6 minutes.when i pressed 'i' for interactive , i see ata3(i think its my DVD-R/W) responding too slow. so, booting stops there till it responds.o/p of
Code:
dmesg | grep -i ata3
gives
[code]...
I am using CentOS 5 Both a production server and VM CentOS get this problem.When issue:
# /etc/rc.d/init.d/haldaemon start
Starting HAL daemon: [FAILED]
I'm not sure if this helps and I'm not sure how to tell anyone what I found, but was a problem in Fedora 10 and 11 were VM's running in KVM would lockup due to (disk or network) IO activity. The problem silently vanished as soon as I installed Fedora 12 as my VM. I upgraded my VM to Fedora 13 and the problem re-surfaced. Oddly, no other distributions seem to have this problem any more judging from Google. My configuration:Host = x86_64, 4 cores, Fedora 11VM = i686, 2 virtual cores, Fedora 10, 11, or 13 (Fedora 12 works)What worked for me was using only one core in my VM. Things have been stable for a few days now
View 1 Replies View RelatedI'm trying to run BoxBackup to sync a couple active servers to a data server. I installed the server and client, making sure to follow the instructions closely with all the certificates. The problem is the service daemon on the service won't even start. The service manage reports: "bbstored dead but pid file exists" (basically, tried to instantiate the process, but it died due to faults).
Here's the log of the daemon in /var/log/box
Code:
Jul 27 13:05:10 frogbert bbstored[13429]: NOTICE: Box Backup Store Server v0.11rc8, (c) Ben Summers and contributors 2003-2010
Jul 27 13:05:10 frogbert bbstored[13433]: NOTICE: Starting daemon, version: 0.11rc8
Jul 27 13:05:10 frogbert bbstored[13433]: NOTICE: Using configuration file: /etc/boxbackup/bbstored.conf
Jul 27 13:05:10 frogbert bbstored[13433]: WARNING: Exception thrown: ServerException(SocketBindError) at ../../lib/server/SocketListen.h(232)
[Code]...
Starting mysqld daemon with databases from /var/lib/mysqli m installed mysql-5.0.77-4.el5_5.4
[root@serv ~]# mysql -u root
ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: NO)
[root@serv ~]# /etc/init.d/mysqld stop
[code]....
I am tring to stop avahi from starting and running at all.I use kill PID and killall avahi-daemon and it will not go away, it comes back with a new PID. Does anyone know a way of stopping it?
View 2 Replies View RelatedI currently have sendmail installed. It starts as a daemon but I want to avoid doing that. I want to start it manually.Also am a dynamic host.so every time i start my computer my ip changes. I use ddclient to update my records at dyndns.com.but how to configure sendmail in the case of dynamic hosts since it looks at the file /etc/hosts which contains information about the static hosts.
View 2 Replies View RelatedI'm using fedora12 with KVM. I'm also using iptables for filtering and nat. Problem is when I start libvirtd, it overwrites my current iptables and iptables config file (/etc/sysconfig/iptables).
Ok it leaves an old copy in /etc/sysconfig/iptables.old, but the main problem is that it removes also all my custom settings from filter and my full nat. I would like the keep control on my iptables and like to manage them on my own. But I cant find an option in the libvirtd config files and/or the libvirtd startup scripts to prevent libvirt from changing my iptables. how I can make libvirtd stop tempering with my iptables?
Getting this error seemingly randomly at login:
There was an error starting the GNOME Settings Daemon.
Some things, such as themes, sounds, or background settings may not work correctly.
The last error message was:
Launch helper exited with unknown return code 1
GNOME will still try to restart the Settings Daemon next time you log in.
I thought I might be logging in to fast, but it happened again when I had waited several minutes.
Unfortunately accidentaly I disconnected my usb drive my computer and my VMs run from so I just rebooted for a quick fix Now I can't open virt-manager locally and the VM's can't get network connections I see this in the logs after the last two reboots
Code:
grep lxc /var/log/messages |tail -n 2
Jan 7 00:45:04 F820 libvirtd: 00:45:04.524: warning : lxcStartup:1895 : Unable to create cgroup for driver: No such device or address
Jan 7 11:52:53 F820 libvirtd: 11:52:53.325: warning : lxcStartup:1895 : Unable to create cgroup for driver: No such device or address
[code]...
I tried restarting libvirtd after with no love so I rebooted and cgroup was gone this was a clean install of F14, after this started I brought the system current, I can provide the packages installed but they errors didnt change
I have a computer that serves as a mp3 playlist for in the kitchen. I just installed it, and now the sound is not playing correctly. When playing a song with rhythmbox, it will crash after about 40 seconds. When I play it with Amarok, it produces sound for about 40 seconds and then the sound stops, although Amarok keeps playing.
I did the following to the system:
- I put an other computer completely in an other case (Motherboard, harddrives, memory, CPU, Power source (you know the box that powers the motherboard and harddrives, etc.) (Yes this has to be done )
- As for the front panel of the old case, the wires could not be attached to the motherboard, so I only attached: 'HD led' and the 'Power button', but I could not attach the front speaker to the motherboard.
- I reinstalled debian etch
- The motherboard had onboard sound in the back, so I didn't install an audio card. However, when I first booted with debian, there was no sound coming from the port. Therefore I installed an audio card in 1 of the PCI slots.
ubuntu 9.10 running most current version i believe *.17the problem is when i bootup it goes and shows the white ubuntu logo then stops. I tried booting up in recovery mode and it says that it "Gave up" waiting for the root partition or the root device. I tried running the LiveCD i have that i used to install and the partition manager shows the partition still there so i have no idea what the problem is.
View 5 Replies View RelatedI need some advice on how to troubleshoot a booting problem. On my F12 installation, kernel 2.6.31.12-174 (and prior) all work fine. Kernels 2.6.32.x all stop booting at "starting udevd" -- even the cursor on the console stops blinking. My system is P4 2.4 GHz with 2 GB RAM on Asus P4PE -- old, but pretty generic.
View 2 Replies View RelatedI have got an Acer 3820T laptop. Among many problems that it seems to have with linux, the most critical one is that when I boot into linux, the fan stops spinning. I have already verified that the relevant modules are loaded into the kernel,
Code:
~$ modprobe --first-time -a processor thermal fan acpi-cpufreq coretemp
Password:
WARNING: Module processor already in kernel (builtin).
WARNING: Module thermal already in kernel (builtin).
[code]....
When I want to start nfs services ,I get this error, Starting NFS daemon: [FAILED]
View 1 Replies View RelatedHave a little experience with backtrack 4, which is a Ubuntu distro. I'm changing to Lenny due to hardware limitations on my laptop, an older Dell inspiron 7000.
Here's the specs :
400 MHZ,
120 G HDD parted as C: = 20G (has bad sectors, left blank) and D: = 20G Windows part
128 Mb low density RAM
ATI Rage Mobility ( not sure of video RAM, I think 8 Mb)
Now I liked running BT and liked the linux work, so when the BT install went south I started to look for another linux distro I can run, the BT tools I use are linux after all. Here's where I hit my stump. I decided to go with the Lenny distro, it already has some of the tools I need, but the first time I installed I had the HDD like this 20G, 20G, 20G,20G, 17.??G. I had windows installed on C: (of course, no problems, yet)
After I installed lenny to D: via an iso I downloaded, the Debian GNU/Linux 5.0.6 "Lenny" - Official i386 xfce+lxde-CD Binary-1, BTW first install was from booting from the disk. After reparting, format, etc. of the install, GRUB boot loader detects my D: Windows, great. Reboot to GRUB boot menu, select ddebian, and it loads...cool, until I realize I don't have synaptic, the tools, and apt isn't going to work unless I can load the linux driver from the cdrom...which I can't find.
Reboot...windows, internet for answers I'm thinkin. GRUB loads fine, select windows and get the following error message "Windows can't start because of hardware configuration problems. Could not read from selected boot disk, check boot path and hardware. Check configuration manual for disk configuration."
It took three days to get Windows reinstalled, and a LL format (zerowrite the drive) but during the process I discovered a possible hdw issue...bad sectors on the C: hdd. Solution: C: 20G = unused, D: = Windows xp. Worked great. No more windows issues, so try it again. This time I used the disks installer from windows. Everything started great, boot menuselected debian, install-graphic, but this time I let the part manager create a drive, 20G from the free space an it appropriately made it's swapfile...when lenny booted it was good, but still no synaptic, cd/rom, couldn't browse the computer.
Reboot to windows to get instructions from someone that really knows what's going on...no windows. exactly same message as before. I was able to boot into debian okay, but couldn't find any drives, utilities, wasn't very much, but I needed my windows and the internet to get lessons. I am familiar with the terminal console and KDE. Can use apt for updating, but prefer using the synaptic. Why does my windows keep disappearing? If I can solve the dual boot issue I can learn the system casually. Right now my config is: C: = 20G, nothing here, still haven't run a scandisk either...next on todo list. D: = 20G Windows install...what I'm using now. I'm not going to attempt to reinstall debian until I receive a efinate answer to the dissappearing config, or boot capacity. Oh, yeah, Did try a fdisk/mbr and fix. this didn't bring it back either.
I currently use mint gnome 9 as my OS but I have am having a problem with the boot up on my computer. It starts booting but then stops with a message saying K8 NPT DATA CHANGE UPDATE NEW DATA to DMI UPDATE SUCCESS and stops there and doesn't go any further. its a BIOS or a CMOS. what this message means and how to fix it?
View 1 Replies View RelatedWe are running Ubuntu on VMWare EXS Server 3i (32 bit server). We tried upgrading from Version 9.4 to 9.10. The server will not boot. It throws networking errors then just comes to a blank black screen.
Here is most of the screen:
/dev/sda5 was not cleanly unmounted, check forced. (note - this is due to having turned it off at the black screen - that much I get)
/dev/sdd1: recovering journal
/dev/sdb1: recovering journal
/dev/sdc1: recovering journal
/dev/sdb1: clean, 74772/6553600 files, 15793957/26214055 blocks (check in 5 mounts)
/dev/sdd1: clean, 22599/6553600 files, 15036060/26214055 blocks
/dev/sdc1: clean, 381500/13107200 files, 34291998/52428119 blocks
Filesystem checks are in progress (ESC to cancel):
***** here is where I think things are going bad ************
init: network-interface (eth0) pre-start process (535) terminated with status 1
init: network-interface (eth0) post-stop process(61 terminated with status 1
init: network-interface (lo) pre-start process (615) terminated with status 1
init: network-interface (lo) post-stop process(62 terminated with status 1
/dev/sda5: 105/124496 files (34.3% non-contiguous), 18894/.248976 blocks
mountall: fsck /boot [410] terminated with status 1
fsck from util-linux-ng 2.16
/dev/FileU32-root: clean, 69429/734400 files, 540860/2933760 blocks
init: networking main process (70 terminated with status 1
The suse 10.0 64 bit partition on my box stops booting when it is setting up the cmos clock. The suse 10.0 32 bit partition boots up without a problem. I never had a problem with the suse 10.0 64 bit partition up until now. Is it possible to fix the problem using puppy linux and editing a configuration file? I do not think it is a hardware issue if the other partition on the drive boots up. Would puppy linux be a good way to backup files from this partition or can I mount the partition using the 32 bit os?
View 1 Replies View RelatedI installed Apache, and it works fine. However, when I rebooted my CentOS, httpd did not start automatically. What do I need to do to ensure it starts when the system boots?
View 2 Replies View RelatedI have a server running 64bit lucid and while trying to get a script to run on boot to start Davmail I appear to have broken something. I have webmin installed but I have been trying to do the majority of things via the command line. I now have davmail starting at boot but a lot of other services don't start anymore, including apache, mysql and webmin. Fortunately SSH still works and I can start apache and webmin from the command line without any problems.
View 1 Replies View RelatedAlthough I'm a linux user, I don't know much about the whole booting process myself. I normally have a friend that I can consult when things don't go the way I expected. But here's the thing: he updated my computer and went away. And of course I can't reach him and I really need it to work. And moreover, I want to be able to sole things myself.
The booting process stops halfway. The last thing it says is: can't access tty: job control turned off (initramfs) ...
I joined a company as an IT staff 2 months plus back. I now encounters a problem that the booting up hangs at the time when it is starting domino services. I have no clue where to look at and duno where to start checking. A little description of the server. : It's a lotus notes domino server for employees webmail service. -> Now it is down. it's an external dns server: recently high volumes of query cache denied surfaces. it's also our proxy server. The only way to get it up and running is to turn off domino service. The system is running still with high volumes of queries I last checked.
Althrough it can boot up now and DNS & proxy are running, I couldn't access the system anymore. It will hang when I attempt to log in from the command prompt. Below is an illustration:
iasaix login: root -> I attempt to log in using root user
password: xxxxxxxx -> I keyed in my password
-> The cursor comes down and just keeps blinking and nothing happens.
Remote access is not possible as it has sshd disabled by default. Our employees cannot access their webmail now, which is a major issue.
No matter if it is safe mode or regular the computer stops booting at Starting smartd I installed wine and samaba files (through Yast) before I restarted the computer and I was looking in FSTAB to get my HD's working. I didn't make any changes to FSTAB (I didn't even save the file).
View 1 Replies View RelatedAfter upgrade from 10.04 to 10.10 on my dual core, 64-bit machine, my miro software has problems downloading torrents. Torrent will start slow and then, after a minute or so, it slows down and stops saying "starting up". It appears there is a bug report, bug 668615, but I've found no fix.
View 3 Replies View Related