I have installed Debian on my intel iMac, I installed grub first in my root partition and then in the Debian partition. When I boot my Mac, rEFIt brings me to the boot page and shows the Linux drive, but when I choose it, it tries to start up and then gives me the line "Not a bootable drive" and just hangs. How to get this to boot?
View 3 RepliesI have a 5,2 macbook pro, and I use refit to boot my ubuntu partition. I do not have an OSX partition on the local drive at all. The only partitions that are on the drive are the EFI, ubuntu and swap. Refit lives on the EFI dos partition.I am experiencing a very long delay on power-on before the system will load refit (probably 20-30 seconds) Once it loads everything is normal.
View 1 Replies View RelatedI have a Mac Pro 1.1 and am having trouble installing Debian. I installed rEFIt but it won't show my install and live disks at startup. I have very little experience with the command line but would be willing to try. I have installed debian to my pc and used the command line successfully there, but want the OS for my mac.
View 4 Replies View RelatedI have a windows 7 machine and installed ubuntu 10.4 32 bit in its own partition. I want to replace the 32 bit ubuntu installation with a 64 bit installation. I downloaded the 64 bit version, booted up on the install cd, and started the install. I got as far as the partition set up before chickening out. I was going to use the manual partition option, select the existing ubuntu partition, reformat, and install. I chickened out because i was afraid that this would also reinstall the grub boot loader without the dual boot option disabling my ability to get into win 7. How should i proceed so that i can replace the existing 32 bit ubuntu with a fresh 64 bit install and still be able to boot into win 7?
View 4 Replies View RelatedI have been using Ubuntu for a while now on a netbook and even installed it on another pc, but I never tried dual-booting before... I just recently built a pc (my first custom build), and I'm having major difficulties getting a dual-boot running with Win 7 and Ubuntu 11.04. I'm trying to install these on one hdd. I don't know if it's a hardware issue or not, but the bios doesn't seem to like grub... I installed Win 7 first, and before installing Ubuntu on a separate partition, Win 7 would boot up fine. (Although, sometimes the bios would ignore my key presses for entering the bios menu or the boot-menu... When I only had Windows installed.)
When I turn on the pc, I mostly get a blinking cursor, with no messages at all. Nothing would boot at all, grub doesn't seem to load, and no OS would load by default. This would even happen sometimes after I set CD-ROM as the first item on the boot order list, trying to boot from the Ubuntu liveCD since there was no way for me to reach either of my installs on my HDD. I tried several suggestions I found online, and nothing seems to help. I even tried both grub 1.99 and grub 0.97, but still not much luck, (Although, grub legacy seems to load slightly more often...) I don't really want to have to resort to using Ubuntu through a VM, but it looks like this is the only option left... Is there some way I can dual boot with something other than grub?
Here's something I noticed after trying Ubuntu a few times. I'm not sure how relevant this is to my issue but, at times, on booting from a liveCD, I see several lines appearing that say something like "over-current change on port 2" should I be worried about this? Is something wrong with my mobo or psu? Another thing and this was before installing Ubuntu, when I boot up the pc, my keyboard is sometimes disabled until it's re-plugged in to a usb port. Maybe this has something to do with over-current charge? I'm just trying to figure out if anything needs to be replaced... I got sick of having to replugin the keyboard since I was constantly restarting the pc, so I started using a less fancy keyboard and it seems to be recognized most of the time (sometimes the bios would still ignore my boot-menu key press attempts).
I set up an array of 2 hhd in raid0 using intel ICH7R, and i have a win7 installed on it. I'd like to have a dual boot with karmic, too. I googled a little bit and i found that it's not so easy as i thought. Are there anyone who's experiencing my same situation?
View 1 Replies View RelatedIs it possible to install Windows XP on a machine that already has Debian 7.8? I find lots of articles on installing Debian after but not before XP.
I would like to get a prompt at startup to select Windows XP or Debian 7.8 and then choose which one I want. The reason I want to do that is because I have Guitar Pro on XP and cant find anything as good and also I want to watch Netflix and cant seem to be able to find a way to do that on Debian 7.8 except windows emulator which defeats the point of Debian anyway. Also my Epson V500 will not work on Debian 7.1 and I have tried everything, been to Epson, installed drivers etc..
WinXP Partition loading as a read only and can't fix it with PYSDM (storage device manager) Let me provide some history as to how everything was installed: From my old WIN XP hard drive I used clonezilla to clone the drive to a partition on my new hard drive for Linux. Windows is on SDA4 which is the last partition of the drive, it is mounted at sda4/windows using ntfs. I then loaded Mint 8 gnome on the 2nd partition sda2 using ext3 mounted at /, sda1 is my Linux swap, and sda3 is mounted at /home using ext3. While installing I selected to mount Linux ext3 at /
When I choose to load winXP from the grub boot loader I get dev/sda4 no such device 10CDR36778638F73. Also when I try to unmount from disk utility I get the following error: Error unmounting: umount exited with exit code 1: helper failed with: umount: only root can unmount UUID=10CDF36778638F73 from /windows Seemslike I need to rename the drive but it won't let me in disk utility.
My Problem is that within PYSDM (storage device manager) I uncheck Mount file system (sda4/windows) as a read only but it will not stay unchecked. I have unchecked it hit unmount and mount and it still is checked to mount as a read only. This is the code in options for sda4 in PYSDM (storage device manager) nls=utf8,umask=007,gid=46
I have a Dell laptop (inspiron 1150) which was dual booting Windows XP and Ubuntu 9.04. I have successfully installed Debian Jessie Standard over the Ubuntu. I pre-partitioned using gparted-live to make a separate single partition for the Debian install. Guided partitioning was then carried out by the installer producing separate /, /home, and swap partitions. After installation, the grub menu shows an entry for Debian and Windows XP. I can boot Debian, but not Windows XP. The symptoms are the same as reported in other forums: A terminal is displayed, vanishes and the system reboots defaulting to the Debian boot.
The grub.cfg file for the Jessie system has an other-os entry:
Code: Select allmenuentry "Microsoft Windows XP Home Edition (on /dev/sda2)" {
set root=(hostdisk//dev/sda, msdos2)
search --no-floppy --fs-uuid --set=root cc0ce0ab0ce091ae
drivemap -s (hd0) ${root}
chainloader +1
}
The original Windows entry for the Ubuntu install was:
Code: Select allmenuentry "Microsoft Windows XP Home Edition (on /dev/sda2)" {
insmod ntfs
set root=(hd0,2)
search --no-floppy --fs-uuid --set cc0ce0ab0ce091ae
drivemap -s (hd0) ${root}
chainloader +1
}
The partitions produced by partman look OK (during the pre-partitioning I did not touch sda1, sda2, or sda3):
Code: Select all~ # fdisk -l
Disk /dev/sda: 37.3 GiB, 40007761920 bytes, 78140160 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
[Code] .....
Partition table entries are not in disk order.
The os-prober found XP:
Code: Select all~ # os-prober
/dev/sda2:Microsoft Windows XP Home Edition:Windows:chain
So it seems that everything is in place, but there are perhaps important differences in the grub.cfg files. Are the two "set root" commands equivalent for example?
how to install Debian after Windows is already installed. Could someone give me a brief guide to begin the process of installing Windows? When I installed Debian I already made a partition for windows (in the same hard disk), I hope I did it right.
View 3 Replies View Relatedis it safe to install a dual boot windows 32bit and a linux 64bit on the same pc?
View 14 Replies View RelatedI'm trying to get dual monitors working on a fresh install of debian from the netinst install cd. I did not allow the installer to download any packages and then manually installed xorg gnome-core & gdm using apt-get.
The monitors are plugged into the onboard vga and dvi ports of my motherboard. I believe the chipset is intel.
At the moment the displays are cloned.
I don't know much about xorg.
This is my xrandr output:
I was able to install Windows 7 64 bit and ubuntu 9.10 along with Mac OS X (10.6) to my MacBook Pro 3,1 (Santa Rosa). Some minor issues remain to be addressed, but all three OSs are functional. My question relates to the rEFIt menu where I only see Mac OS X and Windows as available options, unless I happen to have the ubuntu Live CD inserted or my external drive attached which result in Penguin and/or additional Mac icon, respectively. I get to ubuntu or Windows through the Windows icon in rEFIt, then select one or the other from a long menu in grub, with ubuntu set as the default. BTW: The included OS X option doesn't work from here, of course, and I'd like to remove it at some point since I can't use it, but that's even less important at the moment.
I get "Error 15: File not found" when I try "find /boot/grub/stage1" or "find /grub/stage1" from within the grub utility, as suggested by a previous poster as a start to discovering and relocating the grub loader in order to change the boot behavior. Manually I can navigate to /boot/grub, but I am not at all sure if this is the same thing. With everything essentially working, I don't want to trash what I have. But it would be convenient if I could select Mac OS X, Windows, or ubuntu directly from the rEFIt menu. I am not frightened by command line work but have somewhat limited experience and will welcome any constructive input. I saw posts on this topic dating back to 2008 or early 2009, but current topics didn't seem to match up. I'm also new to posting here and ask for you patience if I am not approaching the forum in the correct way or location.
This seems to be a variant of a problem many people have had, but after several hours trawling through various forums, I haven't seen a reliable match for my situation.In brief:Adding a third boot partition (of Ubuntu) to my existing dual boot of OSX 10.6 and Windows 7 seems to have crippled the Windows boot from working, because Grub apparently takes over the process. Yet Grub does *not* appear to be on the Windows partition.
More verbose:I have an older MacBook Pro (3.1, running Snow Leopard) that I recently refitted with a new 240GB SSD HD. With the extra space (it was previously only 120GB) I decided to add a dual boot with Windows 7 using bootcamp. This all went swimmingly well.Encouraged, I decided to follow this Lifehacker article's suggestion and triple-boot the machine with Ubuntu (I'd never used Linux before):So I now have the nice rEFIt boot partition selection screen, and, indeed, I'm up and running in Ubuntu, and enjoying it.
Only one problem: I can't get into Windows any more. If I try to go in through rEFIt *or* by holding down OPT at startup and selecting the windows partition directly, the result is the same: I get thrown into Grub's selector, and selecting the Windows partition from there leads to an error message and a dead end.Having read through numerous postings, I get the impression that Grub is doing something or living somewhere that it ought not to be, but in most cases I've seen, people had accidentally installed Grub onto the Windows partition (or indeed onto EVERY partition). So far as I can tell, this isn't the case with me. Here's my boot summary:
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
[code]....
I've just installed Debian 6.0.1a on a HP Proliant ML115, the install seemed to go ok. As it began to start up it 'Grub Bootloader' loaded then on the screen after the bootup froze at 'Loading initial ramdisk'
Unfortunately im a complete novice to debian
I installed Fed 11 after Win 7 was already installed---on my Lenovo T-60 laptop. So I rebooted after a couple of software updates with no option to boot to Win 7. my laptop boots straight to Fed 11. So I was checking grub.conf and it is "x'ed" out. so is menu.lst. I click on them and the message says "grub.conf" is not available. Whats up with that? or is there another place to get to the MBR to give me an option between the 2?
View 7 Replies View RelatedI have encountered a problem when installing fedora 12.
1- It told me that there is no sufficient RAM so it logged in text mode. But I have 256 mb RAM and the lowest is 192mb for the graphical mode.
2- The RAM specified in the manual of fedora the DDR or the VGA.
3- After the installation it ask me to log in as shown localhost login:
What should I type in this? Whatever I wrote it ask me to write password. But if I try to write any thing in it, it didn't respond or write any thing.
4- How could I login the graphical mode after installation in text mode.
5- I have encountered another problem when boot the set it load fedora by default and didn't ask me to choose between fedora and previously installed windows xp.
I have Windows xp and Ubuntu 10.04 in my system and last fine morning I was working in windows and when I restarts the system as there were some problem in the audio I found that the grub is not loading. Computer boots directly in the windows xp mode and not giving the possibility to boot in the ubuntu OS. Also, the windows xp restarts continuously with a blue screen for just a second.
This happened out-of-the blue. What might be the possible reason for this and how to get rid of this problem..
Before the installation, I had triple boot of WinXP, Win 7, Ubuntu 10.10. As you can guess, the main boot-loader was grub. The second is Win 7 boot loader, and there it gives the option what to choose, load XP or Win 7.I made a decision to remove Ubuntu and install Debian(you know better than me why I did). So first, I searched a guide how to un-dual-boot. It told me to delete the two partition that Ubuntu use(swap and ext4) and write to MBR the win 7 boot-loader(using EasyBCD), so I delete them and use EeasyBCD. At this stage, I had 2 partitions: NTFS for XP and NTFS for Win 7, and the Win 7 boot-loader(and XP) worked pretty well.I install the latest testing of Debian(6 RC2) from DVD1 using this guide, except I choose to use the graphical installer, ext4(not ext3 as there), install the desktop environment, and choose to install grub(even know it didn't asked me). The swap partition I set is 3 GB because my RAM is 2 GB, even know that ubuntu set it in the past to 2 GB.The installation went pretty well, just when come to grub package, it says that there was an error with installing grub package(it didn't told me what), I had no choice, so I choose to skip over grub/lilo and finish with no boot manager. I was thinking to myself: "So I couldn't install grub, at least I have the Win 7 boot-loader(which contain XP loader), and maybe Win 7 boot-loader will recognize Debian too.". But I end up with no boot at all.It told me than when choose not to install boot-manager that I need to load /vmlinuz and give it the parameter root=/dev/sda4(my deb partition).I think that if I could install grub, I could load all my boots("sudo grub update" right?).How can I fix it?
View 3 Replies View RelatedI am trying to install Ubuntu on a machine that already has Windows 7 on one partition. Obviously I intend to install it on the other free partition. So I downloaded the iso burnt it onto the disk and pop in the disk and the boot the machine. The installation screen comes up I selected the first option (Try Ubuntu without installation), I just see a prompt after a few seconds and then the screen goes blank and nothing happens. Unable to detect a signal, The monitor goes into standby. The same thing happens if I use "install Ubuntu" option as well. I downloaded minimal install version Ubuntu and tried to install with that. since its old school installation, the installation completed without any errors, but when I restart the grub come up and when I select to boot into Ubuntu, I see the same behavior i.e. the screen goes blank and never boots to anything. This is a machine on which I was using 10.4 until yesterday.
View 1 Replies View RelatedI have a 19" and 14" flat panel. There's the onboard Intel graphics, and an old PCI S3 ViRGE card I had laying around.Figured I could make this into a dual head box.Intel is the default display in the BIOS.So far, with the attached configuration, I have the main monitor working properly at 1280x1024@60Hz. Nothing at all on the other monitor. It needs to run at 1024x768@60Hz. If it matters, running Squeeze with LXDE.
/etc/X11/xorg.conf:
Code:
Section "ServerLayout"
Identifier "Default"
Screen 0 "Intel Monitor"
Screen 1 "S3 Monitor" RightOf "Intel Monitor"
InputDevice "Mouse0" "CorePointer"
[code]....
I am brand new to Ubuntu and I am trying to find out if its possible. When the laptop starts it gives me 30secs to choose windows or ubuntu? Is there anyway to change the order or the timer?
View 3 Replies View RelatedI'm having a frustrating time trying to install Ubuntu as a dual boot with Windows 7 on a new Acer Aspire 5750.The initial install proceeded without incident until an error along the lines of "Cannot install GRUB to /dev/sda".I continued without installing GRUB, and attempted to install GRUB from the live CD:Code:sudo mount /dev/sda5 /mntsudo grub-setup -d /mnt/boot/grub /dev/sdaThis installed GRUB, but only linking to my Windows 7 partition (sda2).
View 5 Replies View RelatedIm currently not an linux expert so I turn to this forum after several attempts to fix my issue with grub.
I had a dualboot single HD with both win7 and win8.1 when I decided to install debian wheezy from usb.
I deleted the win7 partition and installed debian there. The partition scheme is separate /home
After reboot I automatically get into the "Grub rescue mode" and now I´m stuck.
I tried the commands:
set prefix=(hd0,msdosX)/boot/grub/
Insmod normal
I have msdos1, msdos3, msdos5 and msdos6 but nothing is listing anything from the grub rescue mode.
I get the "UNKNOWN FILE SYSTEM" error and cant get past that.
I also tried booting into rescue mode from usb iso install but nothing happens when choosing to repair GRUB.
The listed devices in rescue mode are:
/dev/sda1
/dev/sda2
/dev/sda3
/dev/sda5
/dev/sda6
debian uses sdb 1-2 and sdb1 is the only option to Reinstall GRUB on but it gives me "Unable to install GRUB in /dev/sdb1 This is a fatal error" message
/dev/sdb1
/dev/sdb2
I'm a Linux Mint user, but I'd like to cross over to Debian. I used the x86 architecture for the Mint install, but I couldn't find that anywhere on the Debian site. what the architecture for the Intel Pentium D dual core is?
View 2 Replies View RelatedI recently bought a new Samsung netbook N310 and want to install dual-boot Debian lenny along with windows xp home edition. My CPU is like this: Intel Atom CPU N270 1.6GHz which architectures and kernels I should download from the cd installation? there are so many:alpha, amd64, armel, hppa, i386, ia64, mips, mipsel, powerpc, s390, and sparc.
View 4 Replies View RelatedI have Lenny installed & it works fine, in a few days will add Windows 7 (want to dual boot - 1 250 GB hard disk) used gparted to free up lots of room for Win 7
- My question is this, Debian then Win or Win then Debian (I want GRUB to manage both so hope since Lenny is installed Win 7 will use the free space no problem) ?
I'm having a weird problem (2.6.32-2-686-bigmem , sid):
Frequency scaling works on CPU 1 but not on CPU 0.
This is regardless of application, the Gnome applet and cpufreq-selector both fail
I have Debian installed but I need to dual boot with distribution based on Ubuntu 14.04. This is my first UEFI dual boot install attempt. And I must do it right. I must not lose my Debian !
Code: Select allDisk /dev/sdb: 232,9 GiB, 250059350016 bytes, 488397168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
[Code] ....
Ubuntu will go to /dev/sdb5 but I don`t no for sure what to do when installing Ubuntu. How to select during install existing UEFI partition(/dev/sdb1) so Debian and Ubuntu can use it. Can I select existing UEFI partition like I would do for /home or /swap ? Will this work ?
And what will happen with Grub if I select install grub ? I want to manage grub from Debian, it is my main OS. Can I skip Grub install and just update grub on my debian after ubuntu install ? Or I just install grub, then after completed Ubuntu install I install it again from Debian. Will this work ?
Is procedure of installing dual boot trivial like before or UEFI hide`s some unpleasant surprise.
I'll start off with stating my problem and summarize how I got to it.
I installed Windows 10 on an SSD. I installed Debian 8.2 after it. The SSD was/is a GPT disk. I installed both installations from a UEFI booted device (DVD for Windows, and USB drive with Live CD for Debian).
I tested it after each installation making sure I could boot via UEFI into Windows, then Debian, then Windows, to make sure nothing broke.
I rebooted the machine. Suddenly, no more UEFI. Nothing. I didn't change any BIOS/UEFI setup menu settings. Not even my USB drive with Live CD will boot through UEFI anymore. Even when nothing else is plugged into the system.
My situation is actually a bit more complicated than that, but I think that will suffice for now. I can still boot into the Live CD on the USB drive, just in Legacy mode only. I mounted the EFI partition on /mnt/boot after I mounted the file system for Debian on /mnt. It is identical, as far as I can tell, to as it was before when it was working.
My motherboard has CSM and Secure Boot, both have been set up how they need to be to boot UEFI into Debian. Tinkering with them further after things broke did not fix it. I tried all variations of options/settings.
The GRUB Reinstall guide says to be in EFI mode before starting it, so I can't do that.
My motherboard is an ASUS X99 Deluxe, and I've heard ASUS has special "features" (read: bugs) that come with their boards. Searching hasn't brought up any other people with this issue. I believe the firmware is updated to it's most current one.
I've tried dd-ing my backup of my old system, from before trying to migrate to a Dual Boot system, to the SSD (after backing up the dual boot setup with dd -> <name>.img via the Live CD USB). However, that won't boot either as it is a UEFI install as well.
The layout of my EFI partition is as such:
/boot/EFI/Boot/bootx64.efi
/boot/EFI/Microsoft/<Microsoft-naming>.efi
/boot/EFI/debian/grubx64.efi
I've heard that the standards on how that's supposed to be set up isn't a standard. However, since it worked booting into the OS' the first time, I don't see how that could be the issue (a bad hierarchy layout leading to the UEFI not being able to see the OS installs).
I've seen that I can boot to an EFI shell (called Shell.efi, apparently) via an option in my UEFI BIOS setup menu on my motherboard. Is that an option here to somehow bypass this strange issue?
All I can think to try is burn it all and start over. But not knowing what caused it means I could just make it happen again. Plus, I can't boot into UEFI install media, so I can't install UEFI boot OS'. :/