how do I change my 192.168.1.3 to a static ip?
I went into nano /etc/sysconfig/network-script/ifcfg-eth0
I add in IPADDR=192.168.3.55
I do service network restart and it doesn't change to the correct.... ip ??
I am using centOS 5.0. After I change from DHCP to static IP address, I cannot ping hosts on the same subnet. The error message says destination host unreachable. Before I made the changes I was able to ping and now even I change it back to DHCP I still cannot ping with the same destination host unreachable message. The centOS is running on VMware on a Windows host.
ifconfig shows
eth0 Link encap:Ethernet HWaddr 00:0C29:A1:9A:10
inet addr: 192.168.0.202 Bcast:192.168.0.255 Mask: 255.255.255.0
inet6 addr ......
After pinging 192.168.0.106 (106 is on and other host can ping it), arp -a shows ? (192.168.0.106) at <incomplete> on eth0 I tried different ways by disabling the firewall and and disabling SE protection. No Luck.
I am a developer, not a network admin - sorry if this ia dumb question. I need to test an application on CentOS 55 64 bit. The instalation went fine and initially I let DHCP work its magic. The router IP address ia 192.168.0.1 and all other VM's I have are granted dynamic ip address on this range (i.e. 192.168.0.x). However, the CentOS vm got an IP address that looks like it belongs on a different subnet :192.168.1.1
The VM (vmware desktop) network setting for this VM uses "Bridged: Connected directly to the physical network". I can ping the host (Windows 7 64 bit) and the host can ping it (it been the VM) - but no other computer on the network can see it. To make things easier, I changed the network configuration to use a static IP address. Here are my configuration files:
/etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=static
HWADDR=00:0C:29:83:4B:A4
ONBOOT=yes
TYPE=Ethernet
[Code]...
Fedora 12 64bit What will be the correct steps changing dynamic IP to static IP on F12 console, instead of on Gnome running;
System -> Administration -> Network -> Edit, etc.
I made following test;
Edited ifcfg-eth0
$ cat /etc/sysconfig/network-scripts/ifcfg-eth0 Code: # Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
[code]...
Fedora 12 What will be the correct steps changing dynamic IP to static IP on F12 console, instead of on Gnome running;
[Code]....
I have followed some instructions to change to a static ip address and have now lost my connection to my router. The mistake I made was not copying the original "interfaces" file before making changes.The file originally had: auto wlan0 iface wlan0 inet (something - I thought it was loopback but didn't work when I added it).
The instruction told me to put:
auto eth0
iface eth0 inet static
address 192.168.1.100
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.1
Which I did, using my own ip numbers, except for "broadcast". I didn't add that in because I didn't have a clue what to put there. When it didn't work, I tried putting it back to what I originally had except I can't rememebr that last bit. I added dhcp instead of what I thought it was but this didn't work either.
my system is belkin router with dhcp enabled.connected are: win xp desktop, win7 netbook, ps3 and fujtisu laptop with ubuntu 10.10, advent notebook xp. right now i have everything getting its ip addy over dhcp but i want to set static ip for each machine. (so the ps3 can run dmz and ocasionally the belkin changes ip address even tho the lease time is set to forever) i can do this with the windoze machines but i do not know how to set static ip and other info for the ubuntu machine.i did search for the forum for 'static ip' but the results that appeared were nothing to do with dhcp!
View 5 Replies View RelatedIm running ubuntu server 10.10 on my wirtual mashine at home. For now i have few service installed and configured:apache with phpand mysql support,ftp,phpmyadmin.. My ip address is not static, i tryed to configure by following some guide but without success.
First i edit this in /etc/network/interfaces (changing dhcp to static
Code:
# The primary network interface
auto eth0
iface eth0 inet static
[Code].....
Can't change from dhcp to static ip address.I've installed Oracle's version of Linux Redhat 5, but I'm having no success changing from dhcp to a static IP address. My machine is plugged directly into a Belkin router which has the IP address: 192.168.2.1.If I use the gui: /usr/bin/system-config-network and set the network device to dhcp,it works fine. But if I set the IP address manually, I get no internet traffic, and if I ping an internet website, "network unreachable".The installation instructions for Oracle say that they want a full domainname. I've tried gateway.2wire.net. This worked in the last place I did a successful installation.It was the address of my ATT router. If I plunked that into a browser, I got the router configuration.
View 7 Replies View Relatedwhen I do "route -n", I got:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
I need to change the static configuration, like I 169.254.0.0, I don't know how it got there also I want to delete 192.168.1.1 from a static gateway. How can I do this?
Does anyone know an easy way to do this? I can't seem to figure it out.
View 6 Replies View RelatedI am using a 3rd party kernel driver that does not support udev properly. When I was using wheezy I placed the required device files in /lib/udev/devices.
The udev in jessie does not appear to support this. Is there any way to have udev create these device files or will I have to create then using a script at boot-up?
I'm replacing a USB adapter with a PCI DLink card that is an Atheros chipset. I installed 'madwifi' for the modules and can set the ESSID and WEP key manually using iwconfig and can get a DHCP Address using dhclient.
What I want to do now is bind this to the static IP that the USB device used to have, but I am not sure how to do this since Atheros chipsets show up as both wifi0 and ath0, with ath0 being the one that needs to have the connection info. I tried setting up a ifcfg-ath0 with the static IP information and the key-ath0 file with the key like I have for the USB device (which shows up as wlan0) but at booth ath0 isn't up and running, even with ONBOOT=yes. What do I need to do to get an Atheros chipset to boot with a static IP?
the Centos Server Edition , so glad I make that clear , my problem is the changes of my intern ip adress from the Centos server , and i wont to make it Static so it gets always the same ip.
View 2 Replies View RelatedI'm having strange difficulties in setting a static ip for my CentOS 5.4 installation. If I use DHCP everything is fine, but with a static ip I have no network connectivity. I have done this many times with RedHat/Fedora/Ubuntu etc. with no problems and now I have no idea what I'm missing or doing wrong. I have tried to set ip as 192.168.1.20 (anything below .100 will do). GW is 192.168.1.1 and NM is 255.255.255.0. This is all I have had to use with other distros, but now when I set these I cannot even access my routers admin page or ping it (192.168.1.1). (I just did this with Vista on my other machine and all worked fine).
View 13 Replies View Relatedi am trying to assign a Static IP address and for the life of my i cannot get it to work Can someone explain to me the easiest way to do it and if i restart the server it won't get lost either.
View 1 Replies View RelatedHow would you assign a server a public static IP ?
Ok.. I guess to better ask my question... how to assign server public static IP centos? Like for example I am in the router itself.. where would I go to point ip 44.33.33.21. to ?> 192.168.1.4
What would be the most common in the routers?
I am running a modem in bridge mode to my server
I edit file /etc/sysconfig/network-scripts/ifcfg-eth0 code...
I do service network restart and get nothing ? No connection... Are there other files I need to edit?
Server has been moved to a different locations and so the IP has been changed now the hostname is changed to something other that what it was before.
Could it be the rDNS that is causing this?
Note: this is not a DHCP connection.
I have a desktop PC with CentOS 5 installed, and a wireless card that's working well via NetworkManager.
How would I configure the wireless card statically, e. g. by editing /etc/sysconfig/network-scripts/ifcfg-wlan0?
This would be something like :
DEVICE=wlan0
BOOTPROTO=static
ONBOOT=yes
IPADDR=192.168.1.252
NETMASK=255.255.255.0
ESSID=my_essid
CHANNEL=3
But I don't know how to define the WEP key here.
I decided to take the plunge and change the existing static ip configuration for my home network to a dynamic (DHCP) configuration. The DHCP server in this new network config is my gt701-wg actiontec DSL modem.
[Code]....
I am having several boxex with centos on it. No pb. I have recently setup a new box with centos 5.4 and I am not able to get the network working on it when configuring a static ip.I've configured eth0 and dns using "setup": unsuccessfulI've used the network config GUI: unsuccessfulAnd it is working very well when I let the dhcp getting the setting.I need a static IP.Here is the getinfo output when static ip setup, and below it, the getinfo for dhcp setting
== BEGIN uname -rmi ==
2.6.18-194.3.1.el5 i686 i386
== END uname -rmi ==
[code]....
I had something I think if very odd happen to one of my computers at work today, it appears to have spontaneously switched from having a static address set to getting its address by dhcp.this is a small office with a mix of mostly linux servers and desktops with a few stand alone windows computers, mostly notebooks. Most of the desktop computers get their address by dhcp, they all have NIS /NFS for remote mounted home directories (interchangeable desktops so anyone can log in at any desk). The particular desktop computer in question here has a shared printer on its parallel port, so has a static IP. Yesterday a UPS in the server rack died, after pulling it and plugging things back in and restarting the servers, it was easiest just to reboot all the desktops, everything came up ok including the desktop in question, and the printer did work.
Today I pulled the oversized UPS from this desktop to replace the dead one, and put a more appropriately sized one in its place, shut the servers down again, rebooted, etc,About an hour later someone tells me the printer is not working on the desktop, and after a lot of searching I find this desktop has the wrong IP address, I ran system-config-network and it showed the address was set to dhcp, I changed this back to the correct static IP and things seem to be working ok now.
I am having a problem with when I bind a static IP to my NIC I loose all network connectivity but, if i leave it set to dhcp it works fine. I've gone over all my settings a thousand times and they are all correct. Has anyone else had this problem or give me a hint as to what the problem might be?
View 2 Replies View RelatedI'm trying to install CentOS 5.4 from my local repo, booting the server from centos54-netinstall iso (vmware). I write "linux URL..." during boot. I eventually get prompted for network config, where I choose manual configuration. Hitting OK ignores my config and defaults back to dhcp, which won't work since I don't have any dhcp server available.Whats wrong? Is there a bug in anaconda?
View 1 Replies View RelatedI have a CentOS5 server with dual ethernet adapters + Webmin installed as my Router / Firewall / DHCP server working successfully with 1 static IP from my ISP. I also have 7 additional static IP addresses from my ISP needing to configure to individual servers inside my network. I have configured the additional virtual interfaces, but am lost on how to route data specifically from additional ISP address to specific internal network address.
Below is my desired configuration.
98.173.159.xx1 = eth0 physical interface ==> eth1 192.168.1.1
98.173.159.xx2 = eth0:1 virtual interface ==> 192.168.1.10 ==> CentOS Server 2
98.173.159.xx3 = eth0:2 virtual interface ==> 192.168.1.20 ==> CentOS Server 3
98.173.159.xx4 = eth0:3 virtual interface ==> 192.168.1.30 ==> CentOS Server 4
98.173.159.xx5 = eth0:4 virtual interface ==> 192.168.1.40 ==> Mac OS X Server 1
98.173.159.xx6 = eth0:5 virtual interface ==> 192.168.1.50 ==> Mac OS X Server 1
98.173.159.xx7 = eth0:6 virtual interface ==> 192.168.1.60 ==> Network Attached Storage Server 1
98.173.159.xx8 = eth0:7 virtual interface ==> 192.168.1.70 ==> Windows 2008 Server 1
I'm having some problems on the line with ***. This is from a OpenEntidade.java class file and I'm trying to update EmprestadorView's variables.
EmprestadorView.java
public class EmprestadorView extends FrameView {
...
OpenEntidade.java
-----------------
public class OpenEntidade extends javax.swing.JFrame {
[code]....
I have one desktop PC I'd like to use as a jukebox. It's installed in the basement as a black box, with only SSH access, and it has got a minimal CentOS 5.3 install with MPD and NCMPC. It's connected to the hi-fi in the basement, so I can stream music to it when I'm downstairs. Since I didn't want to use cables everywhere, I bought a PCI wireless card, with a RT2561 chip.
Until recently this card worked OK with Linux. Recent kernel version even have out-of-the-box support for it, except of course you still have to download the firmware from the Ralinktech website.
I gave the thing a static IP configuration by editing /etc/sysconfig/network-scripts/ifcfg-wlan0, interface went up fine, I can ping the machine and SSH into it OK. Now the only problem is, when I do a shutdown -h now, the machine "hangs" while trying to bring wlan0 down. (In case you wonder: I temporarily attached a monitor to it, since wanting to know what goes on while shutting down in an SSH session is a chicken-and-egg situation :)). I actually have to hard-reboot it (by pressing RESET).
I had made following entries in my httpd.conf file at centos5.5.
###########################
Listen 80
Listen 8080
Listen 8085[code]....
When i am trying to access the any directory other on port *80, its not being accessible from the static ip which is routed through a DMZ server. http://122.165.35.9:8085 something like this returns the error "could not connect to web browser"
I want to configure a VPN over the Internet.I installed the 'openvpn' package, generated the key file, transfered it by a secure way to the client, and setted up the configuration file.
So, in that configuration file I input the IP addresses of the tunneled interfaces. Both IPs are static in the tunnel.
Then, I've heard somewhere that I can assign a dynamic configuration IP for the client. I do this registering a range.
Well, when I tried to change static IP to dynamic IP (changing '192.168.0.2' to '192.168.0.0/24') in the configuration file, the OpenVPN didn't work.
Obviously I don't know what I'm doing, and I really, don't believe that simply changing the IP will make it work, but I tried.
I hope I explained my problem as well.
My configuration file:
# OpenVPN Server Configuration File
dev tun 0
ifconfig 192.168.0.1 192.168.0.2
cd /etc/openvpn
secret key_file
In client I execute the 'openvpn' without the '--daemon' parameter.Then I want that my client uses a IP in a range (192.168.0.0/24, for example), instead of a static IP (192.168.0.2).I also thought to use a DHCP server, but I'm not sure that will work.