Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05) is not working on centos5.3
# uname -r
2.6.18-128.1.16.el5
# lspci | grep Wireless
0b:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
[Code]....
I'm running Ubuntu 9.10 on a Gateway M520 laptop, and after failing to get the Broadcom wireless chip that came with it working I swapped it out for an Intel PRO/Wireless 2200BG. Unfortunately, I haven't been able to get wireless to work. The chip doesn't appear to be turned on (it is detected though), and the hotkey to switch wireless on/off (Fn+F2) doesn't work in Ubuntu. I also am not sure if I have the proper drivers to get the chip working with Ubuntu, and I'm not sure how to figure that out.
Since I've noticed it's asked for a lot, here's the output for iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
eth2 radio off ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
[Code]....
I was trying to update the drivers for my wireless card and it no longer works. I have a cisco pcmcia card that I got working to use as a backup, but I would prefer to use my internal card. The card is the Intel Pro 2200BG. Please let me know what information is needed to diagnose and correct this issue. I am relatively new to Linux (Currently using F10) and trying to learn.This is the iwconfig from my cisco card. The Intel card was working fine yesterday. but now doesn;t even show up.
[west@garfield ~]$ iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
[code]...
I'm using this card on a Toshiba Tecra M3 laptop. Firmware is installed. iwconfig shows the following:
Code:
eth1 radio off ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
[code]...
Ubuntu, but I like it, and I'm trying to see how powerful it is.I got a non function wireless network card. Here the information that I be able to collect:
- Tabletop HP Compaq tc4200.
- OS Ubuntu 10.04 LTS - the Lucid Linux.
- Wireless interface: Pro/Wireless 2200BG [Calexico2] Network Connection. Vendor: Intel
[code]...
what to do for the wireless
View 1 Replies View RelatedSince an upgrade from 10.10 to 11.04, all wireless devices for me in the plasma network manager applet are not functioning properly on a Dell Latitude E4310. Specific problem: No wireless networks appear in the plasma network manager applet. Manually-configured networks do not connect. A separate CDMA card appears, but cannot establish a connection. The CDMA card does function on 10.10 machines, and formerly worked on this machine. The only wireless 'network' that appears in the plasma network manager widget is 'hidden network'. Manually adding a network and checking "Connect Automatically" does nothing. I attempted a fresh install after the upgrade itself failed the work. There are no networks to click on, and selecting the device itself merely shows the status page.
Further information
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key: off
Power Management: off
rfkill output:
Code:
0: dell-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: dell-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
2: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
dmesg output:
Code:
dmesg | grep iwl
[24.292605] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[24.292610] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[24.292687] iwlagn 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[24.292696] iwlagn 0000:02:00.0: setting latency timer to 64 .....
Here's the CDMA-specific dmesg output:
Code:
[17846.948253] usb 2-1.1: new full speed USB device using ehci_hcd and address 7
[17847.060342] sierra 2-1.1:1.0: Sierra USB modem converter detected
[17847.060650] usb 2-1.1: Sierra USB modem converter now attached to ttyUSB1
[17847.060765] usb 2-1.1: Sierra USB modem converter now attached to ttyUSB2
[17847.060838] usb 2-1.1: Sierra USB modem converter now attached to ttyUSB3
Neither the CDMA card nor any wireless networks are working. If I take the exact same machine and boot from a disk with 10.10, both work.
I have an old Toshiba Satellite A30 Notepad. I've installed Ubuntu 10.04 onto it and everything but WiFi works. I've installed wicd and several other network tools but just can't get Ubuntu to let me use the WiFi connection (the option is greyed out).I know the card works because the last OS (Windows XP) used it without any problems. The card is detected, the drivers are installed and the hardware (slider) switch is set to on.I think the issue is related to the Radio Frequency Kill Switch being on but I don't know how to turn it off.The output from various commands are:
sudo lshw -C network is:
Code:
*-network:0
description: Ethernet interface[code]............
I just finished upgrading from 9.10 to 10.04 via the Update Manager. My first noticeable problem is that my wireless connection with my home network no longer functions on my IBM Thinkpad T42 laptop.The Network Manager applet shows that it detects my home network (and those of several of my neighbors), but I have not been able to get it to connect to this network. I've been using WPA & WPA2 Personal settings for security, and the Network Manager applet had correctly picked up the password that I had been using under 9.10. I've searched the Ubuntu Forums for "wireless T42" and thought I'd found a solution in a posting that recommended using the "wcid" network manager, but I've been unable to find wcid either via the Synaptic Package Manager or the Ubuntu Software Center.
1. I've noticed that in Lucid Lynx the Network Manager applet's icon in the top panel is no longer the vertical bars symbol that it displayed in
Karmic Koala; instead, the icon is a radiating fan display. In the Network Manager's edit Network Connections window, this fan icon is shown on the Wireless Connection tab, while the vertical bars icon is shown on the Mobile Broadband tab.
2. The Wireless Connection tab shows, on the line in which it shows awareness of my home wireless network (as "Auto 389690") that this connection was "Last Used" "1 month ago". It should be saying something like "today".
FWIW, the Network Manager detected my wired "eth0" connection with no difficulty.Both Jaunty and Karmic picked up my home wireless connection without any problems. Now I have no idea what to try next.
I'm having some problems with my wireless connection. I'm on Ubuntu 10.04, on a HP ProBook 4520s, with a RaLink RT3090 wireless network card. I installed the drivers (hopefully correctly), the wireless seems to work correctly, it scans and finds networks, but when I try to connect to one, it times out after some time, while still attempting to connect. I also have a wired connection that works correctly and without problems. Other computers that try to connect to said wireless network manage to do so without any problems, so this has left me a bit baffled, since, like I said, everything seems to be in order.
I'm a new Ubuntu user, so please tell me what other information I need to provide in order to easily and successfully facilitate troubleshooting this, because it is, as you can imagine, quite aggravating, having a laptop that needs to be connected to the internet through a cable.
[URL]
Quote:toracat wrote:Quote:Reason for custom build is the need to disable ieee80211 and ipw2200 pre-built module in kernel. Trying to get wireless working, and I want to use the later versions of these modules in the hope to get wireless working.
I recently formatted an old Dell D600 and installed 9.10 on a single partition. It connects to my Airport just fine hardwired, but I have had no success getting the IntelPro/Wireless 2200BG card to talk wireless. I've entered the SSID and WPA2 security ID with no success.
View 2 Replies View RelatedI've just installed ubuntu 10.04 via wubi through windows 7. Installation seems to have worked fine but i'm having trouble establishing a network connection. The network card is an Intel (R) Pro 100 /ve. It seems that the card has tried to establish a connection via IPv6, when I believe it should be connecting via IPv4.
View 2 Replies View Relatedtrying to connect wireless on wlan0 intel pro wireless 4965 AG or AGN
View 1 Replies View RelatedI want to connect to a 300mbit network (802.11n). With Windows (the same Computer) I am able to connect with full speed, but with Ubuntu Maverick (64bit), and a lot of other distros I tested, I am only able to connect with 54mbit. The builtin wireless network card is an Intel Corporation Centrino Ultimate-N 6300 (rev 35). Is this a driver Problem? I updated to kernel version 2.6.37-rc2 via ppa sources, but with no luck. I tried to extract the windows driver and started it with ndiswrapper, but i properbly made somethng wrong, because the card did not show up, though ndiswrapper said adapter available... oO?
View 2 Replies View RelatedNoob to Ubuntu here and I cannot access my wireless connection. It is working fine right now (wired) but I am using the TV stand as my computer desk right now so... not very practical. I tried following the "howto post a wireless issue (ticket)" but there was too much information for me to be able to put on here.
I have my SSID and my WEP. I am on Verizon DSL (only provider in my area). I tried using the wireless setting in network connections and I tried using DSL. I assumed that SSID+Password=Yay the internet works! but apparently not.
Its a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
I have a brand new Lenovo Thinkpad T402i. A very good and expensive machine, however I have just installed the latest Fedora 15 and my wiresless does not seem to work properly, I can barely ping a website. I have read it's an Intel's bug. I cannot understand how can be possible with Intel...
View 6 Replies View RelatedI have a Dell Vostro 200 with the above wireless card in it and I cant get it to work. I have been on Intel's website and downloaded e1000-8.0.18 and installed as the instructions. But it is still greyed out on the Network Manager. I have just installed Ubuntu Desktop the latest current version.
View 1 Replies View RelatedI've installed opensuse 11.2 on an old IBM thinkpad. The install went without a hitch and when I got to the desktop I inserted my Dlink DWL-G132 wireless USB adapter. Opensuse immediately recognised that a wireless device was attached and I could see my wireless network listed. I entered my WPA password and was able to connect to my routers configuration page by entering 192.168.0.1 in the URL bar of firefox. For some reason I am unable to navigate to any webpage. When I enter a URL firefox acts as though there is no internet connection. The only way I can get the internet on my laptop is to connect it to my router with a cable. I used a wired connection and ran the update utility thinking that perhaps an update would fix the issue but it did not. I know the adapter works because the laptop used to have windows xp installed and I could connect fine with that.
Does anyone here have any idea why I would be able to connect wirelessly to the routers configuration page but not to the internet? I appreciate any advice anyone may have.
I have a new Thinkpad t510 laptop with an intel centrino wireless N card (no bluetooth). I installed ubuntu a couple weeks ago after I got another hard drive in the expansion bay. I have the drive partitioned into two sections, 250gb for file storage, and 250gb for the linux OS. Currently no other OS is installed on the other harddrive.
I have had everything perfect for the past couple weeks, but once i installed some updates today, my wireless fails to work now. Just some general info that you might ask me, lspci | grep Network, returns
00:19.0 Ethernet controller: Intel Corporation 82577LM Gigabit Network Connection (rev 06) 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 Furthermore, on the top right of my screen, my wireless is grey'd out and says no network devices available on hover.
[Code]...
Im trying to connect to my college wireless network. I have looked a thinkwiki and no one has posted any bugs. Any ideas on getting it working again?
I'm new to linux. I've just installed Ubuntu 11.04. It has all been going ok, but the wireless just stopped working all of a sudden. The indicator light turned off and when I tried to turn it back on (Fn+F2) nothing happens. Sometimes, when I restart the computer, the wireless might work; but if the signal is lost the LED on my laptop turns off and I cannot reconnect. Also, in these strange cases that the wireless works when I restart I can manually turn it off (Fn+F2), but nothing happens when I try to switch it back on.
In the menu on the upper right corner I see 'Enable Networking' is checked, but 'Enable Wireless' cannot be modified.
I have a Dell Inspiron 6400 and the wireless device is an Intel Pro/Wireless 3945ABG.
I have tried to follow some of the threads on this forum on similar cases, but the ones that were comprehensible to me did not work (or I actually might not have understood them either). code...
my platform Centos 5.3
i did the following
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
[Code]....
working to sort out the damn wireless for too long. Mine in cent05 5.2 . network manager is on and I can see the icon on tray. It list all the wireless connections too, but just won't connect. WPA encry is disabled. further details below:
# lspci | grep Wireless 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
# ethtool -i eth1
driver: ipw3945
version: 1.2.1dm
firmware-version: 14.2 1:0 ()
bus-info: 0000:0c:00.0
[Code]...
Installed Ubuntu 10.04 on my Sony UX280p with Intel 4965 wireless. Ubuntu detects the card without issues (as far as I can tell). I can see all access points in my area and select my access point and pair with it. I get a DHCP address from the AP (if ifconfig is to be believed) and iwconfig shows the ESSID of my AP but I can't ping the AP or any other computer on the network, nor can I ping the sony from any other computer on my network. Last year I had installed 9.04 on this computer and wifi worked out of the box without any issues.
View 2 Replies View RelatedI have installed Fedora 12 on my laptop and subsequently spent most of the day trying to get the wireless connection to work. Looks like I am not alone with Wireless issues Through searching and reading today I think the problem lies with the fact that the wireless on/off switch is not working. Under Windows, when I press the wifi toggle switch it starts flashing orange. I haven't managed to get it to do anything under Fedora.
# lspci | grep Wireless
06:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
# iwconfig
[code]....
I've got a Dell precision with Kubuntu 9.10. Wifi worked fine on that machine for months, but stopped working last week. I don't know what happened, but I recently did an "apt-get dist-upgrade". That might have something to do with it.
When I boot in Windows, wifi works fine.
Code:
tijl@Smaug:~$ sudo lshw -C network
*-network
description: Ethernet interface
product: 82567LM Gigabit Network Connection
[Code]....
I have a Dell E6500 with and Intel 5300 wireless agn card running Lucid x64. Wireless works fine and speeds are great except when I download with either the browser or thru a torrent or even updates. Once I get to around 100 megs in to the file wireless stops working and the only way to get it working again is to disconnect and reconnect to the AP. I have installed the back ports and tried several other fixed to get this to work but nothing has helped. One more note this happens on 2 other wireless routers that I have tried so I know that it's not limited to my Linksys.
View 3 Replies View RelatedMy wireless worked out of the box for the past few months. When I was running low on battery recently, I put the laptop to sleep. When I woke it up, there was a black screen with a flashing underscore. I pressed a bunch of buttons but nothing happened. Then suddenly it said something about a wireless hardware error and I did a hard reset by holding down the power button. When I turned the computer back on, wireless was greyed out. There's no hardware switch to enable and disable wireless and the software switch had no effect. I tried echoing into the 'state' of the adapter but it didn't let me. When I tried sudo ifconfig wlan0 up it gave me the following error:
Code:
SIOCSIFFLAGS: Unknown error 132
lspci:
[code]....
I can connect to the internet with wired connection. The switch for the device is on but this command "sudo lshw -C network" has the following results:
#
[sudo] password for nn:
*-network
description: Network controller
product: BCM4312 802.11a/b/g
[Code]....