CentOS 5 Hardware :: Attempt To Access Beyond End Of Device

Jul 6, 2010

I have a LVM snapshot that triggers these kernel errors when any LVM-related commands run:

Jul 6 10:31:38 itmanager kernel: attempt to access beyond end of device
Jul 6 10:31:38 itmanager kernel: dm-28: rw=0, want=66156996183394672, limit=25165824

dm-28 is the snapshot volume in device mapper. I think this error is generated because most LVM commands will check the first 4K of various drives and volumes for LVM metadata and labels, but attempts to read any of the first eight sectors (ie: 4K) of this particular snapshot logical volume trigger this error.The most interesting thing is that the snapshot is 25165824 sectors long (12G), but attempts to access the first eight sectors result in an attempt to access sector 66156996183394672!I've obtained an info dump from getinfo.sh disk, and added the output from lvs. You can find the results here:URL.. It's not as if the sectors that back the first 4K of the volume are corrupt, either: the read request never hits any hardware because the read request is attempting to read a non-sensical sector, instead of the correct sector. Perhaps the COW metadata for the snapshot is corrupt?

How do I find the cause of this problem?Is this a critical error that I should file a bug report for?I first noticed this some time after turning the machine on Sunday afternoon.As far as I can tell from the logs, the shutdown the previous evening was normal.I use LVM fairly heavily on this machine, and this is the first time I've ever seen this kind of problem..I've worked around the problem by copying the first eight sectors from the Origin volume, and the rest from the Snapshot volume, to a new normal logical volume.However, I'm still concerned about how this error occurred in the first place.

View 1 Replies


ADVERTISEMENT

CentOS 5 Hardware :: Qla2460: Attempt To Access Beyond End Of Device

Feb 17, 2009

I'm experiencing some strange issues with a C5 installation on a Dell server with a QLA2460 HBA. When it boots up, I got a lot of these messages on dmesg:

[Code]...

View 4 Replies View Related

CentOS 5 :: Unable To Access Resume Device / Enable It?

Mar 7, 2011

I'm running CentOS 5.5 with a hardware Areca controller (Raid 10). I initially installed a machine and rsynced the file system to a third machine; I'm then pulling in the file system to new machines and updating grub with a script to make it bootable.

I've done this before with other machines (no raid sets) but with these machines I'm running into errors code...

View 1 Replies View Related

CentOS 5 Server :: Unable To Access Resume Device?

Sep 23, 2011

I face a problem with my server after i rebooted it i got a message on start up tell me that " Unable to access resume device (label=swap-sdb3) " and the system doesn't startup

the error message exactly is

Unable to access resume device (lable=swap-sdb3)
Creating root device.
Mounting root filesystem.
[ 3.305354] EXT-fs (md1) : error : unable to read superplock
mount: error mounting /dev/root on sysroot as ext3 : invalid argument

[Code]....

View 4 Replies View Related

Ubuntu :: File Access Attempt Denied Monitoring

Jun 25, 2011

I am looking for a file monitor to tell me when a file was attempted to be accessed, but was denied. A windows equivalent could be the auditing feature in server 2k3. I don't know which account or which file is attempting to access or be accessed, but I was hoping something built into Linux would support some sort of file auditing for security purposes.

View 2 Replies View Related

Ubuntu Security :: Undesired Access Attempt To Localhost

Jun 29, 2011

While investigating my localhost access logs during an investigation to resolve locking myself out of my own server(!) I noticed this recent access attempt from a proxy referrer. I wouldn't expect this on a local server - currently set to listen on 127.0.01. The request was 403 forbidden, but surely the request should not have even reached this far? Is this an example of an unauthorised access attempt? I don't think it is me because all of my usual access requests are in moz 5 and im logged in to linux currently.

Note please do not click this link as I do not know where it leads ^^^^! (and i dont know how to disable it on this forum)

View 8 Replies View Related

CentOS 5 :: CentOS 5.5 Crashes During Install Attempt?

Feb 12, 2011

Attempting to install CentOS 5.5 on my desktop box crashes spectacularly. (See [URL]The LiveCD does boot and appears to work, but also fills the screen with random, blinking characters early in the boot process.I was hoping I built a fairly ordinary box, so I'm surprised by this crash. It's an ASUS M4A78T-E AM3 790GX HDMI ATX AMD motherboard. Full specs here:[URL]

View 5 Replies View Related

Debian :: No Browser Access After Failed Iceweasel Upgrade Attempt

Jan 16, 2011

I learned that, even while on Linux, using Iceweasel/Firefox 3.0.6 is not safe. So I tried to update the browser for my PPC G4 iMac (256 MB RAM, 800 MHz processor).

1. I downloaded a backported Iceweasel .deb from URL...

2. I then tried to install it with dpkg -i PathToIceweasel.deb

3. There was an error. I remember seeing xulrunner-1.9.1 is not installed. I tried to install that with apt-get but it was not available.

4. Now when I click on web browser I get the error "Failed to execute default Web Browser: Input/Output error".

5. What can I do without having to reinstall?

View 11 Replies View Related

General :: Filter And Block Failed Attempt To Access Proftp Server?

Jan 7, 2011

I want to filter and block failed attempt to access my proftp server. Here are few line from the /var/log/secure file:Quote:

Jan 2 18:38:25 server1 proftpd[17847]: server1.XYZ.com (93.218.93.95[93.218.93.95]) - Maximum login attempts (3) exceeded
Jan 2 18:38:27 server1 proftpd[17864]: server1.XYZ.com (93.218.93.95[93.218.93.95]) -

[code]....

View 9 Replies View Related

CentOS 5 :: 5.5 Crashes During Install Attempt

Feb 17, 2011

I'm having similar problem to someone else here in the forum (see [URL], but only with the 64 bit version of CentOS 5.5. Almost every time I try to install it, it will crash at some point in the "interactive" startup phase (but it is random). One time, I actually reached the install desktop. I did not attempt an install. I shut the machine down and the system crashed. I haven't been able to get to the install desktop since then.

I have successfully installed CentOS 5.5 32bit, however, on this same machine. In fact, I am writing this from a VM running under CentOS 5.5 32bit on this machine, and do all my work on this machine. I have since upgraded to the latest 2.6.18 kernel with PAE and latest VirtualBox; I have not experienced ANY instability at all with this machine so far. Occasionally, VirtualBox gets an error booting the client, but it has been rare and I've seen this even on older VirtualBox versions on a previous mainboard, so I am not particularly suspicious of that. It is a brand new system, only about a month old. All new parts, except for mostly unused hard drives and drive bays.

[Code]....

View 8 Replies View Related

CentOS 5 :: 403 Forbidden Error On PHPMyAdmin Install Attempt?

Feb 9, 2010

I get "403 Forbidden You don't have permission to access" after attempting an installation of phpmyadmin.

CentOS 5.4
Permissions for directory set to 755 recursively (chomd -R 755 <directory name>)
Directory is in /var/www/html/

I have other test pages in the /var/www/html/ directory that I can access ... I know this seems like a permission issue and in fact the error log states this is a permission issue, but I cannot figure what is the problem here.

View 16 Replies View Related

Hardware :: Possible To Access An IrDA Device As A Serial Device Such As /dev/ttyUSB0?

May 24, 2011

the message from dmesg for the IrDA device:

[ 3635.194162] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 3635.338159] usb 3-1: New USB device found, idVendor=066f, idProduct=4200
[ 3635.338165] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[code]...

View 1 Replies View Related

CentOS 5 :: Downgrade Glibc Due To A Broken Kernel After A Libc6 Upgrade Attempt?

Jul 18, 2009

I need to downgrade glibc due to a broken kernel after a libc6 upgrade attempt. See:[URL]..Especially with the reduced capabilities I have right now (few if any programs are working), how might I go about downgrading glibc to 2.6?

View 1 Replies View Related

CentOS 5 :: Specify The Device Driver When Mounting A Device?

Jul 28, 2010

I have installed live cd on usb pendrive. Everything works great. How can I find out which device driver it is using? Where are the device driver files stored? How do you specify the device driver when mounting a device?

View 3 Replies View Related

CentOS 5 Hardware :: CentOS 5.2 And 5.3 Does Not Recognize Device On IDE IT8213 Controller?

Apr 3, 2009

I have had a Supermicro X7DCL-3 motherboard based machine, running CentOS 5.2 x86_64, recently upgraded to 5.3.Strangely enough, although I must have installed the 5.2 using DVD disk, the running system does not show the DVD drive. The machine was not used very much so I noticed that only today, after the update. There is no trace of it in 'dmesg', thera are no /dev/cd* and/or /dev/dvd* devices. The IDE controller is IT8213 (as shown by 'lspci'). In 5.2 kernel (2.6.18-92.el5-x86_64) lspci says "unknown device". I have checked the /usr/src/kernels/*/.config files and both kernels (5.2 and 2.6.18-128.el5-x86_64 of 5.3) seam to have the support for that controller added into the kernel:CONFIG_BLK_DEV_IT821X=yAny idea why it is not working? The Supermicro has apparently noticed this also as their OS compatibility chart lists the IDE interface for that motherboard as supported up to RHEL 5.1 but not for 5.2.

View 2 Replies View Related

CentOS 5 Hardware :: CentOS USB Device (Velleman K8055) Not Showing Up

Sep 6, 2010

I'm experimenting with a K8055 board, connected through USB to our Asterisk server,running on CentOS. If I connect the device I can see it being connected by watching /var/log/messages. Also the device is mentionned in /proc/bus/usb/devices. But when I do lsusb the device isn't showing up and it should be showing up! If it is not listed with lsusb, I can't connect to it through the k8055 executable...

View 1 Replies View Related

CentOS 5 :: CentOS 5.3 I386 Cannot Support Device Larger Than 2TB?

May 20, 2009

I have been using SLES 10 SP1 so far with about 6TB Raid system without problems.I have upgraded the OS to CentOS 5.3 i386 and I have noticed the kernel can not recognize raid system larger than 2TB.Is there any parameters that I have to set ? or the i386 distribution simply does not support larger raid, so I have to use x86_64 version, instead?

View 1 Replies View Related

CentOS 5 Server :: Named And Access Rights / SELinux - Access Denied

Aug 24, 2010

I configure named and stumble upon the following problem: named is serious about user rights, every config file named uses should be named:named. I set rights to named:named as follows, but they get changed to root:named when I restart named as root. The same thing happens with SELinux context. This results in access denied type errors.

View 1 Replies View Related

CentOS 5 Server :: Cannot Access VMware Via Infrastructure Web Access

May 9, 2011

I've recently installed CentOS 5, because I needed a good OS to run VMware Server. Just a heads up, I'm not very familiar with RH/CentOS distros, I usually use Arch Linux. My VMware install went fine, config is standard settings. Now I'm trying to access the VMware Infrastructure Web Access using port 8222 (http) and 8333 (https), but it's a no go. I'm connecting from another machine on the LAN, as the CentOS box is headless. I restarted the vmware services, and they seem to be launching fine. I don't know much about VMware though. I verified with netstat and ports 8222 and 8333 are listening.

View 3 Replies View Related

Ubuntu :: Cryptsetup - Cannot Access Device

Feb 23, 2010

I have 10 hotswappable SATA drives I use for a rotating backup system. On each drive I have created an encrypted LUKS partition. I normally mount the drive by first unlocking it via:

Code:

cryptsetup luksOpen /dev/sdc1: BD-4-B

However some time last week this command refused to work...for any of the drive. Before I even get prompted for a password I get the terse error message: "Command failed: Can not access device"I can't recall if it was a system update that broke it, but now I can't get to any of the data on these devices nor can I run any backups.

View 1 Replies View Related

Fedora :: Command Failed: Can Not Access Device?

Jan 5, 2010

I updated quite a lot - kernel, selinux policies, initscripts, glibc and a lot more - and after reboot one filesystem does not mount. It says:Command failed: Can not access device... and asks for password. This is: RAID -> LVM (mirrored) -> LUKS -> ext3. Similar filesystem (raid->lvm(not mirrored)->luks->ext3) mounts fine. Mounting the problematic system by hand works fine. During boot, the lvm blockdev is named by UUID in crypttab, and the name used in fstab.

Of course I removed it from fstab to boot now. I tried downgrading initscripts so far, will try others. What I also noticed is that the emergency shell (bash) complains about something, I'd need to write it down next time I reboot; also "lvs" fails when / is ro, but maybe that's normal, dunno.Googling for the error message brought something about cryptsetup, but I didn't upgrade it (there is no upgrade available), and all I gather from it is that the error message might really mean something else, like device is already mapped.

It is probably something related to lvm mirrors, maybe also to luks, though the only related package in the list is the kernel, maybe the module-init-tools. SELinux seems not to be the cause, booting with permissive has the same problem. What I wrote above, leads me to thinking that luks is trying to set up lvm mirrors in parallel as they have the same uuid, but a) later during boot the mapping name is not there b) I have no idea what reads crypttab

View 1 Replies View Related

OpenSUSE :: Terminal Access To A Ethernet Device

Feb 24, 2011

I know that there is support for this, but i can't seem to find any appropriate tools. Let's say my widget is at 192.168.1.111; i need to open a terminal window talking to it. Then i can control the things connected to it (it is a bus converter). oS 11.1, KDE 3.5, various machines.

View 2 Replies View Related

OpenSUSE Hardware :: Changes In USB Device Access With Suse 11.2?

Dec 6, 2009

this weekend I updated the OS on my laptop from OS 10.3 to 11.2.Most things worked fine ... and quickly ... but I have issues with some USB devices.Printers and everthing that works like a Memory Stick, HD (camera, mobile phone) are OK. But after the update to 11.2 I can neither use my scanner anymore nor my Garmin GPS device. Both devices are listed with 'lsusb' correctly. But applications are not able to find/access them.

For the GPS device I do not know how to do more tests. The application (gpsman) that worked fine with 10.3 does not find it anymore. The Scanner is detected by Xsane or Skanlite and also the driver can be installed with Yast when plugged in. But a test fails with "sane_start: Error during Device I/O". 'sane-find-scanner' also lists the device correctly. As a normal user it complains that there is no write access for usblib to the usb device. As root this error does not appear. It can be avoided temporarily by setting chmod 777 to all /dev/bus/usb entries. Then 'sane-find-scanner' does not show any errors.
But the applications do not work.

I already added the normal user to the "lp" group as shown in the /etc/udev/rules.d/55-libsane.rules and tried to give access to the usb-devices in /etc/fstab .... all without success. As I have two USB devices (Scanner, GPS) that worked fine with 10.3 but are not an external HD (or similar), I assume that someting has changed with the handling of USB devices from 10.3 to 11.2.

View 8 Replies View Related

General :: How To Access TrackPad Device In Eeepc

May 24, 2011

I am on an Eeepc running Ubuntu and I am trying to store the raw data from the Eeepc's inbuilt track pad in a file.To do this with the keyboard (as root) I wentcat /dev/input/event7 > ~/raw-keyboard-out.dataThe result was the whole bunch of random-looking data I was hoping for.Now I want to do this for my mouse, and I tried all of the 'files' in this folder in an analogous operation and none of them seem to stream the input into a file.Does anybody know what the name of the TrackPad/mouse device is called in the /dev folder for an Asus Eeepc 1001p?

View 1 Replies View Related

Ubuntu Multimedia :: Access The Photos That Are On The Device, But Nothing Else?

Oct 17, 2010

I just recently purchased an iPod touch 4G running iOS 4.1 under the assumption that it would play nice with Ubuntu as stated here:..Devices/iPhone. It doesn't! I can't seem to get it to work. It shows up as a camera with 86MB of available space. I can access the photos that are on the device, but nothing else. I really would like to be able to transfer music to the device, but nothing seems to work. Rhythmbox doesn't even seem to recognize that it's there, the device isn't showing up in /media, and I can't seem to get a mount point. Has anybody out there had any success in this area? I've tried on both my 10.04 Desktop and 10.10 laptop machines

View 2 Replies View Related

Red Hat / Fedora :: Unable To Access Resume Device

Mar 18, 2010

How do you actually remove and install kernel when the system is not booting.

View 4 Replies View Related

Red Hat / Fedora :: Mailserver Have To Have Direct Access To WAN Or Can It Be A LAN Device With Just One NIC ?

Apr 22, 2010

Does a mailserver have to have direct access to WAN or can it be a LAN device with just one NIC ?

We have two WAN access points.

One is an adsl router joined to the switch and all seems fine for internet browsing.

The other is a wireless system with a linksys router joining by way of PPPoE and this appears to connect fine.

This PPPoE is direct to our ISP and where we need to downlod our mail to our pending mailserver.

When the linksys router is also joined to the switch all devices can use either the adsl or linksys to roam the net. 192.168.1.1 linksys & 192.168.1.10 is adsl.

When I join the linksys direct to the mailserver I will then need two NIC's. One for the Linksys and one for the LAN.

This is where the fun has started.

So.... Can I just have one NIC (connected to the switch) on the mailserver?

View 5 Replies View Related

Ubuntu :: Remote Access With Android Device

Apr 7, 2011

Any way to remote access my Ubuntu Server using my Android phone?

View 2 Replies View Related

General :: Switch CPU To 16 Bits To Access Its Device?

Apr 23, 2010

I have a CPLD (EPM240100T) chip that has data type of 16 bits, but the CPU access it using 8 bit. How do I switch the CPU mode (to 16 bits) to access this chip?

View 2 Replies View Related

Ubuntu Security :: Permanent User Access To A Device?

May 11, 2011

I managed to make an old parallel port scanner work in ubuntu 11.04 with SANE. Everything's perfect but one thing: scanner applications work only if they are executed as a root.After further researching, I've found the cause is that only the root has read and write permissions on the device /dev/parport0 which is my parallel port. If I set the right permissions giving sudo chmod a+rw /dev/parport0 I solve my problem, but just untill next reboot... the system resets root only permissions at each restart. I would like to make that change permanent... what can I do?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved