Red Hat / Fedora :: Unable To Access Resume Device
Mar 18, 2010How do you actually remove and install kernel when the system is not booting.
View 4 Replies
ADVERTISEMENT
Fedora Installation :: Moving FC10 From SATA To PATA - Unable To Access Resume Device
Jan 26, 2010I'm trying to move an existing FC10 install (created by someone else) from a 160GB WD1600AAJS SATA disk to a 160GB WD1600AAJB PATA disk (cursed trend of horizontally mounting SATA connectors at the end of the motherboard means the latest rev mobo doesn't fit in our enclosure!). I've used DD to copy the disk image from one to the other, but when attempting to boot, I get the following error:
Code:
Unable to access resume device (UUID=946f216f-0c24-4b02-a996-f42059970de7)
mount: error mounting /dev/root on /sysroot as ext3: no such file or directory
That particular UUID maps to sda2, which is the swap partition. Interestingly, both the SATA and PATA disk come up as /dev/sda on the motherboard. I kind of grok that the UUIDs are substitutes for directly naming the disks, and that they're referred to in fstab, initrd-2.6.27.12-170.2.5.fc10.i686.img, and in /dev/disk/by-* I'm guessing the problem is that the GUIDs (at least the one for swap) are no longer the same. How are they assigned to the partitions during boot?
I tried doing
Code:
swapoff -a
mkswap /dev/sda2
swapon -a
and put that new GUID in fstab and into initrd-* (using some steps I found elsewhere on how to gunzip/rezip it).At that point, I get a kernel panic on boot
Code:
Kernel panic - not syncing: CFS: Unable to mount root fs on unknown-block(0,0)
So I'm guessing that the other UUUDs have changed as well and I need to update them. How would I figure out what they are? I suppose I could change the references to /dev/sda*, but I didn't build this original image and I'm thinking whoever did had a good reason to go with UUIDs.
Fedora :: Error "unable To Access Resume Device (LABEL=SWAP-sda8)
Mar 7, 2010I have FC6 system with kernel 2.6.22.14-72.fc6 When I rebooted my system, I got error message "unable to access resume device (LABEL=SWAP-sda8) then it went to fsck automatically to all the partition and then stop (failed)
Checking filesystems
/1:clean, 10543/2560864 files, 204494/2560359 blocks
fsck.ext3: unable to resolve 'LABEL=/backup'
/boot: clean, 155076/19546112 files, 13456168/39072080 blocks
[Code]...
CentOS 5 :: Unable To Access Resume Device / Enable It?
Mar 7, 2011I'm running CentOS 5.5 with a hardware Areca controller (Raid 10). I initially installed a machine and rsynced the file system to a third machine; I'm then pulling in the file system to new machines and updating grub with a script to make it bootable.
I've done this before with other machines (no raid sets) but with these machines I'm running into errors code...
CentOS 5 Server :: Unable To Access Resume Device?
Sep 23, 2011I face a problem with my server after i rebooted it i got a message on start up tell me that " Unable to access resume device (label=swap-sdb3) " and the system doesn't startup
the error message exactly is
Unable to access resume device (lable=swap-sdb3)
Creating root device.
Mounting root filesystem.
[ 3.305354] EXT-fs (md1) : error : unable to read superplock
mount: error mounting /dev/root on sysroot as ext3 : invalid argument
[Code]....
Installation :: FC10 - Volume Group "VOLGroup00" Not Found - Unable To Access Resume Device
Feb 2, 2009I already know "what" my problem is, however I am having difficulty fixing it. I recently upgraded our companies server to a HP ML150; decided to upgrade to FC10 hoping it would go smooth and it is not. It does not detect the SATA drives after the installation.
I get.
"Volume Group "VOLGroup00" not found
Unable to access resume device (/dev/VolGroup00/LogVol01
mount: error mounting /dev/root on /sysroot as ext3: No such file or directory
I know the problem is that my SATA is not enabled in the kernel or grub, but I don't know how to fix this. My internet searches are coming up a little short and LIVE discs are not working so I am having trouble figuring this out.
Fedora Installation :: I2O Controller - No Volume Groups Found Volume Group "VolGroup00" Not Found Unable To Access Resume Device
Apr 8, 2009Dual PII 400, 512Mb with a Promise SuperTrak 100 IDE Array Controller. At present I have only one drive on the controller, configured for 1 JBOD array. I install FC9 with no problem. New partition is created and formatted, Grub is installed, and then... Grub is found and booted, but then I get:
Reading all physical volumes. This may take a while... No volume groups found Volume group "VolGroup00" not found Unable to access resume device (/dev/VolGroup00/LogVol01) mount: could not find filesystem '/dev/root' I can boot in rescue mode, chroot to the installed system. I changed the kernel boot parm "root=/dev/VolGroup00/LogVol00"
Fedora :: Resume From Keyboard \ Figure Out Which Is For Which Device?
Jun 17, 2011Currently I only only resume from suspension by pressing the power button. I learned that by editing /proc/acpi/wakeup one can enable resuming from other devices. But how to figure out which is for which device? Here is my /proc/acpi/wakeup file:
Code:
DeviceS-state Status Sysfs node
PCE2 S4*disabled pci:0000:00:02.0
[code]....
General :: Resume From Suspend With Specific Device
Oct 23, 2010I was trying to get this feature: wake up my htpc from s3 with my remote control and the solution is to modify /proc/acpi/wakeup and a descriptor in /sys. Here are the details: I'm using a Microsoft IR receiver for MCE remote that appears as dev 2 of bus 2 in lsusb
root@htpc:~# lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0471:0815 Philips (or NXP) eHome Infrared Receiver
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 045e:0714 Microsoft Corp.
Bus 001 Device 005: ID 045e:0715 Microsoft Corp.
Bus 001 Device 004: ID 045e:0707 Microsoft Corp. Wireless Laser Mouse 8000
Bus 001 Device 003: ID 045e:070c Microsoft Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub....
That's USB0 I have to enabled, why not usb 1 or 2 (bus 2 in lsusb)? Moreover why are all the disabled/enabled preceded with a star and S4 and not S3 mentioned? Nevertheless that wasn't enough to get it work. I looked in gconf-editor in apps/gnome-power-manager/general but I have no can-suspend or something similar... (I'm running on 10.10, with 10.04 I could suspend only once, afterwards the computer didn't go to suspend, just black screen then login screen). So I looked in /sys/ and found that 'cat /sys/bus/usb/devices/2-1/power/wakeup' (notice the 2.1 as bus 2 device 2 (0,1,...) gave 'disabled' so a echo enabled > /sys/bus/usb/devices/2-1/power/wakeup and now I can wake-up with the remote when I want.
What I don't understand:
Why USB0 in /proc/acpi/wakeup ?
Why have to change in /proc and /sys ?
Is it possible to automate this to get it work even if I change the usb port the receiver is plugged in ?
Software :: TuxOnIce Device Resume From Suspend Takes Way Too Long
Aug 5, 2011I am having trouble with a rather peculiar timeout during resume from suspension and I was wondering if any of you have encountered the error or might have some leads as to what causes the problem.I am using Gentoo Linux with TuxOnIce patched kernel. While both hibernation and suspension works as advertised, there is a rather irritating timeout while trying to resume from suspension. Each and every time it takes about 60s for notebook to resume back to X session again, no matter what the conditions are (i.e. USB deviced plugged in, etc.)
View 3 Replies View RelatedUbuntu Networking :: See The Phrase " Device Not Ready" Greyed Out, And Unable To Access A Wireless Network?
Oct 10, 2010Everytime I to turn on my wireless device, and try to connect to a wireless network, i see the phrase " device not ready" greyed out, and not able to access a wireless network. i do not know what to do
View 6 Replies View RelatedFedora :: Command Failed: Can Not Access Device?
Jan 5, 2010I updated quite a lot - kernel, selinux policies, initscripts, glibc and a lot more - and after reboot one filesystem does not mount. It says:Command failed: Can not access device... and asks for password. This is: RAID -> LVM (mirrored) -> LUKS -> ext3. Similar filesystem (raid->lvm(not mirrored)->luks->ext3) mounts fine. Mounting the problematic system by hand works fine. During boot, the lvm blockdev is named by UUID in crypttab, and the name used in fstab.
Of course I removed it from fstab to boot now. I tried downgrading initscripts so far, will try others. What I also noticed is that the emergency shell (bash) complains about something, I'd need to write it down next time I reboot; also "lvs" fails when / is ro, but maybe that's normal, dunno.Googling for the error message brought something about cryptsetup, but I didn't upgrade it (there is no upgrade available), and all I gather from it is that the error message might really mean something else, like device is already mapped.
It is probably something related to lvm mirrors, maybe also to luks, though the only related package in the list is the kernel, maybe the module-init-tools. SELinux seems not to be the cause, booting with permissive has the same problem. What I wrote above, leads me to thinking that luks is trying to set up lvm mirrors in parallel as they have the same uuid, but a) later during boot the mapping name is not there b) I have no idea what reads crypttab
Red Hat / Fedora :: Mailserver Have To Have Direct Access To WAN Or Can It Be A LAN Device With Just One NIC ?
Apr 22, 2010Does a mailserver have to have direct access to WAN or can it be a LAN device with just one NIC ?
We have two WAN access points.
One is an adsl router joined to the switch and all seems fine for internet browsing.
The other is a wireless system with a linksys router joining by way of PPPoE and this appears to connect fine.
This PPPoE is direct to our ISP and where we need to downlod our mail to our pending mailserver.
When the linksys router is also joined to the switch all devices can use either the adsl or linksys to roam the net. 192.168.1.1 linksys & 192.168.1.10 is adsl.
When I join the linksys direct to the mailserver I will then need two NIC's. One for the Linksys and one for the LAN.
This is where the fun has started.
So.... Can I just have one NIC (connected to the switch) on the mailserver?
Hardware :: Possible To Access An IrDA Device As A Serial Device Such As /dev/ttyUSB0?
May 24, 2011the message from dmesg for the IrDA device:
[ 3635.194162] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 3635.338159] usb 3-1: New USB device found, idVendor=066f, idProduct=4200
[ 3635.338165] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[code]...
Ubuntu :: Unable To Resume From Hibernation
Sep 8, 2010I'm having trouble resuming from hibernation. The splash screen loads up with "Resuming from /dev/sda6" (this is the correct partition) and the HDD light shows it's reading the drive. It then stops reading and the loading animation starts up (I'm running Lucid). Then nothing, just the animation. I recently updated initramfs-tools to 0.98ubuntu2~lucid as hibernation wouldn't work at all with the old version (see [URL]). I've also installed this script because of errors on hibernation.
I've posted the output from recovery mode after hibernation below:
Begin: Loading essential drivers ... done
Begin: Running /scripts/init-premount ... done
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done
Begin: Running /scripts/local-premount ... [ 3.280440] PM: Starting manual resume from disk
[3.281560] Freezing user space processes ... (elapsed 0.00 seconds) done.
[3.281898] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[3.306778] PM: Loading image data pages (126908 pages) ... done
[11.121294] PM: Read 444708 kbytes in 6.96 seconds (63.89 MB/s)
[11.121388] Suspending console(s) (use no_console_suspend to debug)
[11.121606] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[11.123474] pm_op(): usb_dev_freeze+0x0/0x20 returns -2
[11.123477] PM: Device usb8 failed to quiesce: error -2
[11.123707] PM: Restore failed, recovering.
[11.149854] Restarting tasks ... done.
Fedora :: Unable To Find Root Device In 14?
Jan 17, 2011out in finding root device of fedora 14. I've windows XP and fedora 14 installed on. this is the output for blkid
/dev/sda1: UUID="962C8EA82C8E834B" TYPE="ntfs"
/dev/sda5: UUID="262C06BF2C068A4F" TYPE="ntfs"
/dev/sda6: UUID="cbcf539a-dee1-4f2f-b68c-ce315ae76e0f" TYPE="ext4"
[code]...
Fedora :: Unable To Enumerate USB Device On Port 2
Jun 29, 2011i have this error in my log but i don't know why?
Quote:
Jun 19 20:34:08 localhost kernel: [352155.875643] hub 2-1:1.0: unable to enumerate USB device on port 2
Jun 19 20:34:08 localhost kernel: [352155.851515] usb 2-1.2: new low speed USB device using ehci_hcd and address 17
Jun 19 20:34:08 localhost kernel: [352155.677964] usb 2-1.2: device descriptor read/64, error -32
Jun 19 20:34:08 localhost kernel: [352155.503404] usb 2-1.2: device descriptor read/64, error -32
[code]....
The Motherboard is a Intel Desktop Board DH55TC, Sockel 1156, mATX, HDMI
Fedora :: Unable To Enumerate USB Device On Port 4
Jul 21, 2011After installation I boot a few times and used F15 on my Dell Inspiron 1564. But now I can't boot anymore. The screen just shows "unable to enumerate USB device on Port 4" and just hangs there with a blinking cursor below that line. I have no USB devices attached though.
View 2 Replies View RelatedUbuntu Multimedia :: Unable To Open Device /dev/dsp - Device Or Resource Busy
Apr 13, 2010All my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?
View 3 Replies View RelatedFedora :: Unable To Find Root Device Booting 14?
Mar 19, 2011I've installed Fedora 15 with Fedora 14 already installed in other partitions, but now I can't boot Fedora 14 as it prompts "no root device found", these are both grub.confQuote:
#boot=/dev/sda
default=0
timeout=120
[code]...
CentOS 5 :: Boot Message About "resume Device"?
Aug 1, 2010When I boot CentOS 5.5, I receive the message:Unable to access resume device ( UUID = some UUID etc. )How do I find out what actual device to which this UUID refers ? It does not appear to be a block device since it does not show when I try 'blkid'.To what does "resume device" refer ?
View 6 Replies View RelatedFedora :: ACPI: Unable To Turn Cooling Device [db816540] 'on'
Jan 10, 2010I installed Fedora on my notebook ASUS. When I type on terminal dmesg apper this:
ACPI: Unable to turn cooling device [db816540] 'on'
I try to search a solution for this but I don't find it.
Fedora Networking :: Fedora 10 Unable To Access To Windows Share Folders On LAN
Jan 8, 2009I am using F10 desktop edition, all the computers using windows are able to access the shared folders over lan except me using F10. I have tried many things with smb but still unable to connect.I am new to linux so i dont khow much of its technicalities.kindly suggest how can i be able to access the shared documents ..
View 1 Replies View RelatedFedora Networking :: Unable To Access Fedora 10 Shared Folder From Windows
Aug 17, 2009Linux OS : Fedora 10 (No graphical mode)Windows OS : XP and Windows Server NT...I am able to access from my windows to linux using following step//fedora10 ip username of admin and password...I am able to view the admin and shared printer of fedora 10.When i try to enter in the admin folder i am not able to access it. It is giving error "Access is denied".
View 6 Replies View RelatedFedora :: Unable To Access Fedora From Grub Command Line?
Feb 9, 2011i recently did some changes to my hard disk partitonand now linux is in hd0,6when i booted my pc,i got the grub commmand line interfaceso,I think that i need to edit grub.conf in fedora 14then at cmd i did this:
grub> root (hd0,6)
grub> kernel (hd0,6)/vmlinuz
file not found
[code]....
Fedora :: Unable To Access RPM Fusion?
Feb 5, 2010after adding the rpm fusion repository and issuing "yum update", it responds with:
Loaded plugins: fastestmirror, presto, refresh-packagekit
Loading mirror speeds from cached hostfile
Could not retrieve mirrorlist http://mirrors.rpmfusion.org/mirrorl...a-11&arch=i386 error
[Code]....
how to get my linux-based machine to retrieve this mirrorlist?!
Fedora :: 12 - Unable To Access Repositories ?
Feb 12, 2010I just did a clean install of Fedora 12 on a system running Fedora 11.
I'm behind a proxy, and I followed the steps outlined at [url] to fix the initial repository error.
This is what I get now:
Code:
My /etc/hosts.conf looks like this
Code:
Also,
Code:
General :: Can't Find Boot Device - Error "Unable To Determine Major/minor Number Of Root Device"
Mar 17, 2011I just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
Fedora Networking :: Unable To Access The Login
May 27, 2009I installed fedora 10 and shut it down after failing to have ..... run to it. later when I turned on the computer after loading 100% a black screen comes up and i cannot access any further. How can I solve the problem without reinstalling the OS.
View 2 Replies View RelatedFedora :: Unable To Access The Virtual Terminals In 10
Feb 1, 2009loaded fedora 10 on my laptop.I get the runlevel 5 in the first one (CTRL+ALT+F5).nothing happens when I press the F2 through F6.
View 3 Replies View Related