I'm trying to setup a CentOS 5.5 with 1 NIC to have several IP addresses on same subnet, each with different MAC addresses. I tried macvlan and multimac but both gives same MAC address (the one of physical NIC) for all IP addresses configured in ARP table on remote hosts. Is it possible to send the 'right' MAC address in ARP requests of corresponding IP address?
View 7 RepliesI have one router, a linksys. It allows wireless and wired connections, as is normal. I have two XP machinesby wire to the router and three linux machines connected wirelessly. The XP machines both have IP addresses beginning with 192.168. while my three linux machines have IP addresses that all begin with 172. None of the machines is connected with a static IP address. All are automatic DHCP.I am told that the above scenario makes no sense. However, such is what I have so, I trust, the theory and the fact do not gel. I would not care except that I cannot see - using the nautilus network servers program, all of the XP computers with some of my linux boxes.
View 9 Replies View Relatedi was installed two ubuntu(1,2) via wmware on my laptop(win=7) on one of them run dhcpserver (ubuntu-1) and i am going to run the other one dhcp client(ubuntu-2) but on the one NIC that belong to my laptop how to config dhcp client (ununtu-2) get ip adres fom dhcserver(ubuntu 1)
View 3 Replies View RelatedIs it possible to have one static IP address with a NAT network forwarding each domain name to certain internal/DMZ IP addresses? I know you can do it by port but if both websites are on port 80 can you forward to the corresponding server on the dmz.I ask this because I noticed the website braemere.com.au had to be typed into a web browser and entering the IP which is 202.47.5.7 did not take me to the website.
View 5 Replies View RelatedIs it possible to create virtual network adapter on the same physical network adapter? or How to give or have multiple MAC Address to the same adpater? I m working on centos 5.3.
View 6 Replies View RelatedAt present, I have:
a Netgear router with DHCP off at 192.168.0.1 my computer
eth0 at 192.168.0.2
wlan0 at 192.168.0.2
The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation.
If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected.
Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).
We can add multiple IP address on a single NIC. Is there any limitation that is how many ip address I can add on a single NIC card??
View 1 Replies View RelatedI'm having an issue in Evolution after upgrading to 11.04 in which upon autocompletion when typing emailaddresses in the To/CC fields, is slower than molasses.
I'm trying to troubleshoot this issue, but in my Evolution the Personal addressbook (from Contacts) is displayed 7 times. That is I have one CouchDB, one entry for the Exchange 2003 server, and 7 "On This Computer/Personal" addressbooks.
Any contact I add in one of these end up in every single of the others, even though none of these addressbooks are in use. But I can give every addressbook an individual name, so it appears to individual addressbooks.
I have searched the home folder and /usr for where I can find these and remove them, but they simply are nowhere to be found.
Does anyone know in which file I need to edit in order to fix this, and does anyone else have the slow autocompletion problem after upgrading to 11.04?
Currently my OS is Ubuntu 9.04 Jaunty Jackalope Desktop OS and my web server is Apache2. I have a public address 60.x.y.z and my pc local address is 10.x.y.z. I have a web app in my Apache2 which currently run in localhost(10.x.y.z).
I would like to enable the web app so that it could be browse from outside. I know there maybe some port forwarding process and some commands involved in order to do that. But I have no idea on the steps to do that.
I am working on implementing a protocol on NS2.34 .I really need help to solve this problem . Actually , I don't now whether the problem is generated by the tcl code or the c++ code when I run the simulation, I get this result :
Code:
num_nodes is set 64
INITIALIZE THE LIST xListHead
34
45
channel.cc:sendUp - Calc highestAntennaZ_ and distCST_
highestAntennaZ_ = 1.5, distCST_ = 550.0
SORTING LISTS ...DONE!
code....
Consider the following program:
Code:
#include <stdio.h>
#include <stdint.h>
[code]...
Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
I'm running Ubuntu 10.10 and I'm having problems trying to assign it a static IP address. No matter what I put in the Preferences->Networking area (identifying the interface as Manual)... it still will query DHCP for an address if I run the dhclient command. I'm using to using ubuntu server where I just set the IP in the interfaces config file.
View 1 Replies View RelatedI am running my own Postfix mail server. Some time ago I noticed that most email was rejected because of the server's dynamic IP address. So I got a fixed IP address. However then I noticed that some mails got rejected due to failing the reverse DNS check. So my ISP told me to get a range of IP addresses and they could then create a PTR record for one of those addresses. That is now running but it turns out that the IP address used for the PTR record is a ... dynamic IP address. So Spamhaus PBL rejects my emails again.
View 1 Replies View RelatedI have a few external IP's assigned to me by my ISP. I have IPcop as my router/firewall. I am wondering how to bind 1 of my external ip's to my internal ip address. So I do not have to port forward, etc. For Example, 77.77.77.77 to 192.168.1.123 and on the server it see's the external IP address.
View 2 Replies View Relatedcan we block email address in a way that a user cannot login into multiple systems simultaneously, so that if a user logs in into a system (with ip address 192.168.1.22)and if he tries to login to into another system at the same time(with ip address 10.0.0.5) his previous system(i.e 192.168.1.22) has to logout automatically. Is there any predefined scripts for this.
View 2 Replies View RelatedI want to configure multiple virtual ethernet interfaces over a single physical ethernet interface (eth0) and for each virtual interface the MAC address must be unique and the IP address must be Static.Finally all the virtual interfaces must be able to communicate both internally and externally and the traffic should be captured using wireshark.
I need to have such kind of setup to communicate devices individually using one physical ethernet device.
Because I was fiddling with few kernel modules like MACVLAN and MACVTAP and successfully enabled those modules and rebuild kernel. Using macvlan and macvtap I can configure virtual interfaces with unique mac address and static IPs but while capturing packets using wireshark interfaces behave weirdly.
For example say on HOST machine I have 1 physical interface and created 3 virtual interfaces as shown below.
Interfaces :
eth0 (physical ethernet interface)
IP: 192.168.A.A
MAC: aa:aa:aa:aa:aa:aa
[Code] ....
First from above interfaces I started pinging eth0 internally from host machine in which it worked as usually.
Second I did same externally from other machine which is connected to the same network of Host machine, and this did work as usually.
Third I pinged first virtual interface veth0 both internally and externally and this also works and after that I did check source and destination MAC address using wireshark tool-where both showed up there respective MAC address.
Now triggers the issue, where I pinged second virtual interface same like I did for first one, but this time ping was success and where as in wireshark tool the MAC address for veth0 is picked by veth1. This is where I got stuck and this issue happened for all the remaining virtual interfaces.
I couldn't see any virtual interface showing their respective MAC address, as of the remaining except the first virtual interface has been picking the first veth0 mac address.
In my job I use some ethernet embedded devices. They take an ip address from dhcp server or auto ip. I only know mac address.How can I obtain ip from mac address? In other words I need a rarp packet generator.
View 6 Replies View RelatedI dont know for what reason, since 2 days, I started having this message whenever I try to start httpd.I commented "Listen 443", restarted httpd started correctly. I needed to comment "listen 443" in order to be able to start httpdWhat is strange is when I do
Code:
telnet mylinux 443
it responds
[code]...
how to assign a address to my ethernet card all the options available
View 1 Replies View RelatedI have an old pentium 3 computer that has ~7 NICs installed. These NICs are attached to modems and other networking equipment. According to the linux ping page on computerhope.com, it seems that one could send a ping from a certain specified NIC. How would one go about this?
View 6 Replies View RelatedI have a CentOS 5.3 box with three network interfaces in it. Each interface is attached to a separate VLAN and I want traffic to stay on each network segment.What I can�t figure out is why I cannot get each interface to have its own gateway and everything gets sent through the default gateway.The basically takes my possible 3Gb total bandwidth and throws it down a single 1Gb pipe.Then on top of that, if I take down the interface (ifdown) that has the current default gateway,I loose contact to the other two interfaces.When I look at the routes, each one of the interfaces shows the gw as 0.0.0.0 and defers to the default route. So I delete the route and try to add a new route with:
[root@testsan ~]# ip route add 10.1.15.0/24 via 10.1.15.1 dev eth2
but end up with the error:
RTNETLINK answers: Network is unreachable
[root@testsan sysconfig]# cat network
NETWORKING=yes
NETWORKING_IPV6=no[code].....
I have a dedicated control computer that can only be accessed with web-browser (with its ip-address). My DHCP-server gives a static ip-address to the control computer (base on its mac-address). Somehow and after some time the control computer looses its ip-address (can't ping to it any more) ... and then I have to reset the control computer to get it to pick up the ip-address ... this is not a good solution since the control computer is not nearby. is there a way to force the control computer to renew its ip-address based on its mac-address
View 1 Replies View RelatedMy security software has picked up multiple port scanning detections on my router/network and only the IP addresses are available. Is it possible to find out what the remote mac address is to see if the IP source has been spoofed? I've got a couple of different IP sources which were found scanning my ports.
I don't know if my IP and the remote IP address are on the same network or subnet for that matter which is the reason for my wanting to know what the mac address is to find out if its coming from the same remote machine.
how to get the mac address from given ip address
View 3 Replies View Relatedi know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
[Code]....
What I want: multiple virtual hosts with ssl and only 1 ip address: In my example: server = 192.168.227.129
[Code]....
I installed a copy of Kubuntu on my desktop at work yesterday & I was able to connect to the Internet just fine then but today when I came in I can not get an IP address, from what I can tell. ifconfig just lists the following. eth0 Link encap:Ethernet HWaddr 00:08:74:bc:b0:59 inet6 addr: fe80::208:74ff:febc:b059/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:278 errors:0 Dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17792 (17.7 KB) TX bytes:3952 (3.9 KB) Interrupt:17
View 8 Replies View RelatedIm an academic (university networks and security lecturer) studying/teaching network and operating system security, and inspired by the work of Hovav Shacham set about testing ASLR on linux. Principley I did this by performing a brute force buffer overflow attack on Fedora 10 and Ubuntu 9. I did this by writting a little concurrent server daemon which accidently on purpose didnt do bounds checking.
I then wrote a client to send it a malicious string brute forcing guessed addresses which caused a return-to-libc to the function usleep with a parameter of 16m causing a delay of 16 seconds as laid out in [URL] Once I hit the delay I new I had found the function and could calculate delta_mmap allowing me to create a standard chained ret-to-libc attack. All of that works fine. However .... To complete my understanding I am trying establish where I can find the standard base address for ubuntu 9 (and other distros) for the following, taken from Shacham:-
Quote:
[code]....
/proc/uid/maps gives me some information but not the base address ldd also gives me the randomised starting address for sections in the user address space but neither gives me the base address. Intrestingly ... when a run ldd with aslr on for over (about) 100 times and checked the start point of libc I determined that the last 3 (least significant) hex digits were always 0's and the fist 4 (most significant) where between 0xB7D7 and 0xB7F9. To me this indicated that bits 22-31 were fixed and bits 12-21 were randomized with bits 11-0 fixed. Although even that doesnt define the boundaries observed correctly.
Note: I am replicating the attack to provide signatures to detect it using IDS, and for teaching purposes. I am NOT a hacker and if needed to could reply from my .ac.uk email address as verification.
I want to pass ip address,port address and some parameters from command line using python script.The ip address and port address for establishing socket connection and remaining parameters to execute different connection.
View 1 Replies View Related