I have recently installed ubuntu desktop i386 10.10 on my laptop (Saony vaio VPCF137HG) as a dual boot. When it first started it worked perfectly, but when I installed the nvidia driver (For a nvidia Geforce 425M GPU) it came to the purple screen (Pic of screen) and no further. It doesn't respond to any commands and would not go any further, even after 40 mins!
View 3 RepliesI updated my fedora 12 GNOME installation. Now Compiz fusion is not working. It says Accelerated 3D support not found. Though Nvidia drivers are already installed. Now I can't even ALT+TAB between open applications.
I tried "metacity -- replace" but then windows wore a weird look with only a minimize button. No sign of maximise & close buttons.
I've just installed Lucid Lynx on both my machines in the interest of sitting and waiting for the Unity/Gnome 3 storm to blow over. On the HP (see below), everything works great, and I've followed instructions online on how to upgrade to LibreOffice, upgrade the kernel to 2.6.38 using the kernel PPA, etc.
However, on the IBM, I'm using Nvidia proprietary graphics drivers. These work well on the stock kernel that 10.04 installed (2.6.32-32), but installing 2.6.38 seems to break the driver. If I install the driver first, and then the kernel on top, X stops working and I have to revert to the default, generic driver to get back in. Once there, I cannot install the driver again. The Additional Drivers dialog goes through the motions, but then drops a "systemerror: installarchives() failed" error message.
So, is there a different version of the driver I should be trying to install? I should clarify at this point I tried all three options the Additional Drivers dialog provided me, all gave the same result (version 96, version 173, and version current).
Or should I leave the kernel at 2.6.32? Is there any downside to leaving it?
I am experiencing the following issue. After enabling SLI and PhysX in windows vista, my dual boot fedora 10 does not see the NVIDIA driver.
Doing: cat /proc/drivers/nvidia/0 I get? in the VGA bios for both cards.
I disabled both SLI and PhysX in vista, but the problem persists. I powerdown and unplugged the rig for several hours without results.
Here are my specs:
CPU: Intel Q9300
Board: MSI P7N Diamond
CARD0: EVGA Gforce 8800 GTS
CARD1: EVGA Gforce 8800 GTS
RAM : 4 Gbytes OCZ gold PC6400 (4 x 1 Gbytes)
PSU : Thermaltake SLI ready 850 W
It is important to mention that initially Fedora did see the cards and I was able to set up a dual monitor system. It right was after I enable SLI and PhysX and re-booting into Linux that the problem showed up.
I have seen this issue before in another machine with an ASUS board, but not until today I associated with the SLI setup. My guess is that there has to be something that the driver is enabling in the cards that messes up the interface between the nvidia.ko module and the kernel, but I don't know what may fix it. I need this system for some numerical calculations.
I'm in the live CD right now trying to figure out what to do. When I first got into Ubuntu, it asked me to install nVidia drivers, so I did. Afterwards, it said I needed to restart my computer to finish installation, but when upon getting past the bootloader, my screen hangs on "Assuming drive cache: write through". I found this post: [URL] but the terminal commands didn't help and I can't find /etc/xorg.cfg even if I show hidden files. I've added a picture of the screen I get when I try to boot up, so maybe someone can tell me what to do to get back into Ubuntu. I would like to be able to get back without having to reinstall, if possible.
View 1 Replies View RelatedThis is my first day with Umbuntu and my first post here at the forums. I bought a Dell Pentium 4 with a fresh install of Umbuntu 9.10 on it. Worked well until I decided to do something a newbie shouldn't do and install a graphics card and drivers. The graphics card worked just fine until the drivers were installed and I tried to reboot the system. Now it no longer boots. Some specifics for you.
Since my time with Ubuntu is limited to hours, the nomenclature will probably be wrong. But I will try to get the point across. The card is a EVGA GeForce FX 5700 Ultra. On first start up with this card the computer functioned fine. I went to a place where you could change the screen options. There were three selections and I don't remember the names (idiot that I am). I selected the middle one. The OS stated that in order to utilize all the capabilities of nvidia graphics cards blah, blah, blah, a driver would need to be downloaded and activated. No name, just a driver. OK, do it (sounds kinda windows like). The download seemed to go OK, but now I needed to reboot to activate the driver.
Now: Ubuntu logo comes up. Screen goes to a text screen that says:
Ubuntu 9.10 dave-ubuntu tty1
dave-ubuntu login:
This screen flashes and does not take input from the keyboard or mouse. Next, I removed the graphics card and used the on-board graphics. Same result with faster flashing. What have I done? Apparently Ubuntu and Linux in general don't have a system recovery option? I read something about the GRUB menu, but the system flasher GRUB loading for half a second and then is on to locking up. I can't seem to get to a GRUB menu. What a way to finish the day.
I have install Ubuntu 10.10 64bit in my sony vaio vpccw16fs which have Nvidia graphics card (GT 230M). I have install it using nomodeset and after entering the system I installed nvidia from System> Administration> Additional drivers. Driver version was current 260.19.06. After installation I was able to see the boot screen but was unable to see the logon screen. The computer froze with the background color of bootscreen which is purple. And I have to restart it and have to choose failsafe graphic mode. And after logging in in failsafe graphic mode. My NVidia driver says I am not using it. How to use nvidia driver properly. I have tried many Tutorials present on internet but none of them works.
Here is my xorg.conf file.
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 260.19.06 (buildmeister@builder101) Mon Sep 13 04:59:45 PDT 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection .....
I bought a new NVIDIA GeForce 6600GT video card for this PC recently and now whenever I boot Ubuntu 9.10 Live I can't change the screen resolution from 640 X 480. I get this message to the effect that the driver is restricted and not free software. When I try to download it and use it it says I can only activate it after a reboot, but I guess it means after rebooting an installation of Ubuntu, not the live cd since it never takes.
Ubuntu recommends NVIDIA accelerated graphics driver 185, so I went to NVIDIA's web site and downloaded NVIDIA-Linux-x86-185.18.36-pkg1.run (and NVIDIA-Linux-x86-190.53-pkg1.run since I think it's the newest, at least when I enter GeForce 6 Series and Linux 32-bit in the driver download search it's what comes up). I noticed that at the beginning menu of the Ubuntu 9.10 Live cd, when you press F4, the option to load from a driver disk is there. I was hoping this means I could just put one or both of the above files on a cd, insert it into the other disk drive and select that option.
Upgraded to 10.04 with proprietary Nvidia driver. No plymouth at boot, but dmesg gives error below. On shutdown get large plymouth display. Tried several hints but none work.
2.985912] 1179648 pages RAM
[ 2.985914] 951810 pages HighMem
[ 2.985915] 149486 pages reserved
[ 2.985916] 642 pages shared
[ 2.985917] 208097 pages non-shared
[Code]...
I've just installed 10.04 on my Dell Latitude D830 with a NVIDIA Quadro NVS 140M; upon booting Ubuntu asked me to install the official NVIDIA driver (latest) so I went ahead and installed it, now the boot splash screen is in about 640x480/800x600 rather than the usual 1920x1200 it was when I first booted.
View 4 Replies View Relatedi just installed nvidia driver 96 manually and after reboot pc wont boot, nothing no output , no beep even if removing ram but fans still work and lights too, did a cmos reset but still got the same result,
View 1 Replies View RelatedI get plymouth and install it success, but it only support nouveau(nvidia) mode.
When I update my driver with [URL] , plymouth gone.
Is there any other way to do boot-image with the driver from [URL] ?
I find super-image-manager(buc), but I can not install it.
Addition: What is buc ?
Fedora 13-64. While booting the nvidia driver has a segmentation fault:
Code:
Enabling the nvidia driver: /etc/rc.d/init.d/functions: line 530: 1406 Segmentation fault "$@"[FAILED] It is not a problem when using the notebook's led/mouse/keyboard. The problem is when I'm using an external monitor/mouse/keyboard. In this case I must first boot using the notebook until it gets to the login screen when I can start using the external configuration. That is annoying because the notebook seats under the table and must be put over the table to boot. The notebook model is HP DV6 2173 CL with a discrete GeForce G105M
My other notebook running Ubuntu works exactly as needed. The whole boot process is shown and controlled by the external monitor/mouse/keyboard.
I have installed F13 and after reading some Nvidia Driver installation guides I managed to blacklist nouveu driver. I run the 'init 3' command and it gave me an error something like 'nouveu driver still in use' then I reboot the system and the fonts were bigger than I run init 3 command again and this time installation was completed then I went back with init 5 command. I opened nvidia x server settings I have cloned the monitors and I installed the flash player,totem vs. Than F13 gave me the notification about updates and with yum update command It has downloaded and installed those updates. Then I shut the system off. When I restarted system it does not boot up. I see the loading bar and It hangs on at the end like forever. I have installed fedora again and the process I have done was same so the result.
View 2 Replies View RelatedI realize that many have had the issue of getting a black screen when booting up. I'm posting because I've tried a couple fixes that I read after doing a search and haven't had any luck yet. I have the 64-bit 10.04 installed on my netbook and my issue surfaced after installing the current nVidia accelerated graphics driver. Following the install ubuntu now boots to a black screen and nothing more. 'nomodeset' only allows me to boot ubuntu in low-graphics mode (which I'm in now) and this fix hasn't produced a solution either: [URL]..64&postcount=9 My netbook has nVidia ION2 graphics with an integrated as well as a discreet graphics card (Intel GMA3150 and NVIDIA GT21
View 9 Replies View RelatedEvery time I boot, I get the following when the Nvidia driver tries to load.
Here is the Backtrace
Memory map:
Segfault during boot of nvidia drivers, anyone know what's causing it? Boot log is here: [URL] It cites a segfault in my /etc/rc.d/init.d/functions at ine 513.
View 2 Replies View RelatedHey everyone I'm pretty new to ubuntu/linux so please bear with me . I recently installed 10.10 on my new htpc. The initial install went great, until I went to install the updated driver for my graphics card. What I did was I downloaded the driver off of nvidia. Then I did these steps:
1. ctrl-alt-f1
2. logged in
3. sudo services gdm stop
4. I then located the driver package that I downloaded and ran it, it seemed to install fine (except for an error about some install script? but it let me proceed)
5. sudo services gdm start
It went to the gdm/ubuntu desktop. However I then connected it via HDMI, and the resolution was way off (top bar was not even displayed on TV) and I tried many different settings but no luck in fixing it. Next after restarting it did not automatically boot to the gdm/desktop. Instead it stayed at the command line login (the ctrl-alt-f1 screen).
tl;dr : 1. How to make it automatically boot to the gdm/desktop after I updated my gpu driver
2. How to fix the resolution for HDMI from my gpu to my TV. (DVI works fine
My system with kernel-2.6.35.10-74.fc14.x86_64, NVIDIA 3800 + Samsung 2233 and 3Dvision kit works fine, but upon upgrading to kernel-2.6.35.13-92.fc14.x86_64 the system won't go past the blue->white bar along the screen. The modprobe.d directory has the file blacklisting nouveau and there is the grub entry rdblacklist=nouveau, but do I need to re-run the nvidia installer. If so I think I need to reset the init level to stop X11 trying to load. and will I need to keep doing this everytime I upgrade the kernel if I have nvidia drivers installed?
Leigh123linux desired code output is below
***
abrt-addon-kerneloops-1.1.18-1.fc14.x86_64
kernel-2.6.35.10-74.fc14.x86_64
kernel-2.6.35.13-91.fc14.x86_64
[Code]....
I have successfully installed the Nvidia driver on my FC13 system that is using an Nvidia NV44 (Ge 6200) card. It seems to be working as I see the nvidia driver when I do a lsmod | grep nvidia and the glxgears program works as well as the nvidia-settings program.Basically, I did the following:
Code:
yum install kmod-nvidia-PAE
new-kernel-pkg --mkinitrd --dracut --update $(rpm -q --queryformat="%{version}-%{release}.%
[code]...
since i installed nvidia proprietary driver on opensuse 11.3 my boot-image is gone. This is not really in issue but i would like to have it back. is there a way to get it back or a bootimage howto or something?
View 5 Replies View RelatedI installed the nvidia driver from the official repository for openSUSE 11.3 and now everything works perfectly, except i get a verbose splash screen after the grub menu.It has worked after i upgraded from 11.2. In my menu.lst it already says splash=silent.If you want more information, please ask, because i don't know where to look or what to show you (i'm fairly new to linux in general).
View 6 Replies View Relatedi just upgraded to the latest nvidia 8 series driver, i downloaded from the nvidia site. After i installed the driver, i reboot and it booted into the console login screen with no GUI. how do i get back into the GUI.
View 1 Replies View Relatedi installed the new beta 10.04 and it seemed right after the install and update that both nvidia hardware drivers were automatically install together. i deactivated both drivers. one driver showed the nvidia 173 driver and the other one showed "current" nvidia driver.
after a restart i then tried to activate the 173 driver. system required a restart. so i did. system booted to a black screen. i believe its at the desktop but i am unable to see it. i tried to hit esc at the boot screen to enter the grub menu but that didnt work.
I just updated my Debian testing as usual (apt-get update && apt-get dist-upgrade), and it totally screwed up Nvidia drivers. I had to revert to integrated graphic card to start Xorg.
After that, I noticed that libgl1-nvidia-glx is missing, and when I tried to install it back, it produces the following:
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
libgl1-nvidia-glx : Depends: libgl1-nvidia-alternatives but it is not going to be installed
E: Broken packages
Any ideas what's going on with it?
I upgraded my Linux kernel from 2.6.35-23-generic to 2.6.35-24-generic and the Broadcom wireless STA driver stopped working. If I try to reinstall it with Jockey it fails and shows this in the log:
[Code]....
Arch linux 32-bit AMD 2400XP, ATI Radeon 7500 Graphics Just did a system upgrade which included xorg-server being upgraded to version 1.7.4.901 This seems to have broken the "radeon" driver--I get a very dim green screen. I have now got the system running with the vesa driver.
Google shows that there is a known issue here, but I did not see my exact symptoms or a cure.
Only about 1.5 weeks into Linux guys so bear with me. I'm trying to uninstall the Nouveau driver and install NVIDIA-Linux-x86-71.86.14-pkg1.run for my old Nvidia TNT2 card. Following these directions I run into a problem in the first step. When I execute the Ctrl+Alt+F1 command and get:
Ubuntu 10.10 splat-desktop tty1 splat-desktop login: if I enter splat which I believe is my username and the correct p/w I get an incorrect login response.
I'm trying to install Atheros AR9485 wireless card driver on debian, and I had no luck.
I followed this [URL] .... to install backports kernel version. The wireless card worked, however, intel display driver displayed the color in the wrong way.
Red pixels are green, and green are yellow. It was displayed like when someone try to connect a PAL system to a TV that supports only NTSC.
This is my lspci output:
Code: Select all00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 09)
00:03.0 Audio device: Intel Corporation Device 0a0c (rev 09)
00:14.0 USB controller: Intel Corporation Lynx Point-LP USB xHCI HC (rev 04)
00:16.0 Communication controller: Intel Corporation Lynx Point-LP HECI #0 (rev 04)
[Code] ....
Is there is a way to compile only AR9485 module from the kernel?
Add the following
Code: Select alli915.i915_enable_fbc=0 to your GRUB_CMDLINE_LINUX_DEFAULT= in /etc/default/grub so you would have something like that
Code: Select allGRUB_CMDLINE_LINUX_DEFAULT=" i915.i915_enable_fbc=0 nomodeset quiet splash"
The freeze's on my machine only appears when i monitor the temperature of
the gpu. Normally i use gkrellm to monitor temperatures including the gpu temperature. When i stop gkrellm there a no more freeze's on my system. Then i started nvdock which also monitor the gpu temperature and the freeze's are back. Stopping nvdock make the system working normally. I have done a few reboots now, warm and also cold starts und everything works normal.
System data: AMD P2 X4 940, Nvidia GTS 250, openSUSE 11.3, Nvidiadriver 256.44,
Gigabyte Mainboard GA-MA78G-DS3H rev.2,8GB RAM, KDE 4.4.95,