Ubuntu :: Install Drivers To Install / Boot After Installation From Raid Drives

Mar 1, 2011

Installing Ubuntu 10.10 desktop.on a Highpoint rocketraid 2642.Installing Ubuntu, it does not find the drive?How do I install the drivers to install and boot after the installation from the raid drives?

View 1 Replies


ADVERTISEMENT

Ubuntu Installation :: Add LSI Drivers For 9750 RAID Controller During Install

Sep 1, 2010

I need to add the LSI drivers for the 9750 RAID controller during the install. These drivers are not included in 10.04 (or 10.04.1) and I need to install onto the RAID device I've created. LSI provides the drivers and instructions here - [URL]

Here are my steps, with the drivers on a USB drive -
Code:
Boot from the installation CD and select Install Ubuntu Server.
Press CTRL+ALT+F2 to switch to console 2 while Ubuntu detects the network.
# mkdir /mnt2 /3ware
# mount /dev/sda1 /mnt2
NOTE: LSI drivers are at /dev/sda1, via USB
# cp /mnt2/9750-server.tgz /3ware
# cd /3ware ; tar zxvf 9750-server.tgz
# umount /mnt2

* Remove the USB flash before insmod command *
# insmod /3ware/2.6.32-21-generic/3w-sas.ko

Press CTRL+ALT+F1 to return to the installer. Continue the installation as usual. Do not reboot when the installation is complete. Press CTRL+ALT+F2 to switch to console 2 again.

# cp /3ware/2.6.32-21-server/3w-sas.ko /target/lib/modules/2.6.32-21-server/kernel/drivers/scsi
# chroot /target
# /sbin/depmod -a 2.6.32-21-server
# update-initramfs -u -v
# exit

Press CTRL+ALT+F1 to return to the installer. Reboot to complete the installation. There are no errors, but after I reboot I just get "GRUB" in the upper left corner, nothing else.

View 2 Replies View Related

Fedora Installation :: Raid On Dell R210 - Install Driver - Sees 2 Separate Drives?

Jun 4, 2011

Fedora is having trouble identifying a raid partition, it sees them as separate drives. I got drivers from dell, but during a Fedora dvd install, it mentions nothing about a place to install extra drivers.

When it says it must "initialize" the drives, Fedora then breaks the dell bios raid. How to either install the dell drivers or make Fedora see the raid partition as one?

View 1 Replies View Related

Ubuntu Installation :: Install Ubuntu On Two 250-gigabyte Hard Drives In A RAID 1 Array?

Apr 4, 2010

I'm about to install Ubuntu on two 250-gigabyte hard drives in a RAID 1 array, but I'm confused about how to partition my hard drives. How much space should I give to each partition? How many partitions should I create and where should I mount them? (I should mention that Ubuntu will be the only OS on this array.)

View 3 Replies View Related

Ubuntu :: RAID Or LVM - Adding Two Hard Drives After Install

Oct 30, 2010

I have the newest Ubuntu installed on my machine. It currently has a 160GB sata drive. I just bought two shiny new 2TB drives that I want to RAID as 4TB. How do I go about adding these two hard drives even though install is complete? I want the 4TB assigned to my /home directory.

View 4 Replies View Related

Ubuntu Installation :: Boot Disk Image For Install On AMD RAID PC?

Sep 3, 2010

I tried installing Ubuntu 10.04 WS on my PC but it did not see any disks to install on. I believe this is because my drives are all configured as RAID. My mobo is an Asus M3A78-EMH HDMI AM2+ socket with an Athlon 2X 5000+ CPU. The chipset is AMD 780G. I have the BIOS configured for RAID drives and I already run Win XP x32 and Win 7 x64 on it. My boot drive is configured as 'RAID READY' and I have 2 RAID 1 disks consisting of pairs of SATA drives.

From what I have researched it seems that with some tuning it should be possible to install Ubuntu 10.04 but I have little Linux experience and don't want to mess up my existing drives. I have installed Linux before a few times and run it but never with RAID. Is anyone aware of an existing disk image that I will be able to install from on my system or would it be possible for someone to create one for me to use?

View 4 Replies View Related

Ubuntu Installation :: Wish To Install As Dual Boot On A Nvidia RAID

Jun 2, 2011

I am currently with Wubi 10.04 under Vista and my Dell XPS 630i has a 1 TB Nvidia RAID controller.First image (Option A) suggests /dev/sda as device for boot loader installation, while second image (Option B) suggests /dev/mapper/nvidia_bcidhdja.I think that the way of keeping the RAID would be using Option B as the device for boot loader installation. Would Option A break the RAID instead?

View 1 Replies View Related

Ubuntu Installation :: RAID 0 And Win7 Dual Boot - Grub Cannot Install

Sep 13, 2010

I'm having serious troubles to install ubuntu-10.04.1. My raid is an hardware raid with intel chipset. Note that win7 is already installed and working with my raid. I made some space from windows, to install Ubuntu (40gb). First, I run the installer, everything seems to be fine. I choose to install Ubuntu were there is the most space free (sorry, I'm not sure about the real terms used there).

Then my partition with the vista loader appears. So the installer can see my raid, and should work fine (everything is detected correctly). But once I'm in the end of the installation (around 95%), a pop-up appears, and tells me that Grub can't install in /dev/sda and it's a fatal error. I can choose an another destination, but it doesn't seems to work.

View 9 Replies View Related

Debian Installation :: Will Not Boot After Install On Areca ARC-1110 RAID

Dec 1, 2010

I performed an install using the 5.0.6 amd64 netinst cd on a dual opteron server with an Areca ARC-1110 4-port SATA hardware RAID card. I have 2 250GB drives set up as RAID 1. The debian install saw it as only one drive, just as it should. Install went smoothly, but on reboot, the system would not load.

I did some research and tried a couple of things with no luck. Like adding a delay in the grub command. It jus sits at loading system for a while then times out and loads busy box. Just to check things out, I booted into an Ubuntu live-cd and mounted the volume. The file system is there and all of the necessary files. How to use one of these cards successfully?

View 2 Replies View Related

Ubuntu Installation :: 9.10 Wont Boot After Fresh Install - Raid Grub Missing ?

Mar 12, 2010

I had ubu 904 and vista installed on an 80gb drive, i had a spare 80gb drive also. I setup a raid0 config in my bios, then installed ubu9.10 onto it. All was fine until the very end, and then it said grub failed to install.

So i rebooted, and im left with a blinking cursor. How do i install grub? Ive installed ubu a few times now and never had an issue so now im lost.

View 1 Replies View Related

Ubuntu Installation :: NTFS Error Stops Dual-boot Install On Fake-raid?

Feb 23, 2011

I am attempting to install Maverick on an older pc. It has (2) mirrored 153 GB SATA drives. I set aside 33GB for a linux partition, by shrinking the partition in Vista.

Choosing to "Install along side windows" is not an available option. I can only choose use who disk, or use empty area. I choose use the empty area, and the Ubiquity installer gets hung up when attempting to format the empty space as EXT4. When I scroll up on the output I notice some error messages referencing NTFS. When I use Gparted it shows a possible problem.

Quote:

Warning:
The device /dev/sda1 doesn't exist
ntfsresize v2.0.0 (libntfs 10:0:0
ERROR(2):Failed to check 'dev/sda1' mount state: No such
file or directory
Probably /etc/mtab is missing. It's too risky to continue. You
might try an another Linux ditro.

Unable to read the contents of this file system!Because of this some operations may be unavailable.

The following list of software packages is required for ntfs file system support: ntfsprogs.

I ran chkdsk /r on the Vista partiton, in case there was a problem there. The issue still persists.

View 2 Replies View Related

OpenSUSE Install :: How Comes Centos Has Drivers For Raid Chip

Feb 3, 2011

I have got a server which has a motherboard with nvidia mediashield raid built in, with Centos installed it picked up the raid 5 array that i had configured as one drive so the os install was straight forward. When i booted the netinstaller of opensuse 11.3 run though the setup, when getting to the partition setup is was picking up the three hdd as seperate drives and not one, so i got to a certain point and aborted the installation and i re run the installer, the raid status said the array was degarded or something which i knew there was nothing wrong with it as i had set it up only about 2 weeks ago and there was one drive missing aswell. So i removed the array and re configured the array and rebooted and the raid status said healthy again as it was before on centos, then i run the opensuse installer again and it went though the process again but completely stop at "Searching for linux partitions" , cursor was working fine , but nothing else was so i had to press reset.

This was my problem, i know kind of what the problem is, but what i want to know is , i thought opensuse is based on rhel same as centos but how comes centos has the drivers for the raid chip i have in my board and opensuse has not.

View 5 Replies View Related

Hardware :: Won't Install Drivers For RR2310 Software Raid Card?

Aug 12, 2010

Trying to install drivers for Highpoint Technology's RR2310 RAID card as a data driveFollowing the simple instructions from HT seems to go well. Typeingsudo sh .install.shreturns:The disk you insert is for linux kernel 2.6Update initrd file /boot/initrd.img-2.6.28-11-generic for 2.6.28-11-genericPlease reboot the system to use the new driver module.When I reboot things are as before: no array; the individual drives are fdisked as singles with no partition table.When I check uname -r, I see the Ubuntu 9.04 kernel is 2.6.31-19-generic.In /boot there are initrd files 2.6.28... 11, 15, 16, & 17 and 2.6.31... 16, 17, 19 & 22.The card BIOS shows the array is 'NORMAL' and lspci shows it also

00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)

[code]...

View 3 Replies View Related

Hardware :: Mega Raid Showing Warning "0:0:RAID-1:2 Drives:153GB:Optimal Drives:2 (11528 Errors)"

Apr 8, 2010

i have cretaed RAID on one of my server RAID health is ok but its shows warning. so what could be the problem. WARNING: 0:0:RAID-1:2 drives:153GB:Optimal Drives:2 (11528 Errors)

View 1 Replies View Related

Ubuntu Installation :: New Install - No Drives For Install ?

Sep 7, 2010

I just purchased an HP HPE-210f (AMD Phenom II quad core). I would like to run Win7 and Ubuntu side by side. However, at step 4 of the installation (from USB drive) where the installer is trying to repartition the drive, the installer does not seem to recognize the disk... very odd. I've never had this problem before installing Ubuntu. The drive does not "show up" on the list of possibilities. There is simply nothing there!

View 9 Replies View Related

Ubuntu :: Raid Install Won't Boot?

Dec 13, 2010

Did a CD install, 64 bit Ubuntu 10.10 on Intel dx38 MB with Intel raid on two 160g drives.

I setup the raid drives (raid 1 mirrored) prior to installing. Install went without problems. On reboot the volume will not boot. I brought up again from CD and the volume is clean and mountable. There are two partitions - dm-1 and dm-2 swap

What can I do to make this boot?

View 1 Replies View Related

Slackware :: Windows Raid-O Install Virtualbox, Will Slackware Install Raid-o Without Raid Driver?

Feb 28, 2011

If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?

View 1 Replies View Related

Installation :: Live Disks Won't Install Drivers Or Install?

Feb 19, 2009

So far I've tried gOS, Linux Mint, Ubuntu, and SuZE. The result is the same: The live disk runs, opens up but the graphics are shoddy, sound doesn't work, everything is very slow, and in attempting to partition and install the os, it stays at "Resizing partitions 0%"I know Live disks are going to be a bit slower, but this is super slow and this computer is just a few months old. Usually the live cds have a database of drivers for common media but it just isn't accelerating the graphics or even recognizing my wireless. I know its not the CDs because they work fine on other (much older) computers.

View 2 Replies View Related

Ubuntu Installation :: Grub - Setup: Warning: Attempting To Install GRUB To A Partition Instead Of The MBR - Install - Lvm - Luks - Raid - Karmic Server

Mar 27, 2010

I'm running Karmic Server with GRUB2 on a Dell XPS 420. Everything was running fine until I changed 2 BIOS settings in an attempt to make my Virtual Box guests run faster. I turned on SpeedStep and Virtualization, rebooted, and I was slapped in the face with a grub error 15. I can't, in my wildest dreams, imagine how these two settings could cause a problem for GRUB, but they have. To make matters worse, I've set my server up to use Luks encrypted LVMs on soft-RAID. From what I can gather, it seems my only hope is to reinstall GRUB. So, I've tried to follow the Live CD instructions outlined in the following article (adding the necessary steps to mount my RAID volumes and LVMs). [URL]

If I try mounting the root lvm as 'dev/vg-root' on /mnt and the boot partition as 'dev/md0' on /mnt/boot, when I try to run the command $sudo grub-install --root-directory=/mnt/ /dev/md0, I get an errors: grub-setup: warn: Attempting to install GRUB to a partition instead of the MBR. This is a BAD idea. grub-setup: error: Embedding is not possible, but this is required when the root device is on a RAID array or LVM volume.

Somewhere in my troubleshooting, I also tried mounting the root lvm as 'dev/mapper/vg-root'. This results in the grub-install error: $sudo grub-install --root-directory=/mnt/ /dev/md0 Invalid device 'dev/md0'

Obviously, neither case fixes the problem. I've been searching and troubleshooting for several hours this evening, and I must have my system operational by Monday morning. That means if I don't have a solution by pretty early tomorrow morning...I'm screwed. A full rebuild will by my only option.

View 4 Replies View Related

Ubuntu :: Install Failure - Nvidia Raid And No Boot?

Sep 13, 2010

on my pc, that was running WinXP, I thought of installing Ubuntu. (I did install linux already a few times in the past years and use it on another couple of pcs) But something went wrong. This machine has 2 x 200MB maxtor drives, in raid 0 configuration, supported by the motherboard Nvidia chipset, and working well in Windows. When ran the live Ubuntu 10.04 cd, gparted was not able to access the drives in raid configuration, until I installed the mdadm and kpartx packages then the existing data became visible. So after that initial moment I thought all was ok and proceeded to install Lucid on the machine, dual booting with Windows. I did partition manually so that in my 400GB raid drive there is an 80GB NTFS partition with WinXP, a 90GB extended partition for Linux Ext4 and Swap and then a last NTFS 200GB partition for data. All went well, but now on restarting the computer nothing happens, nothing loads, Grub is not showing, and it looks like I cannot launch Linux nor Windows. All the data from WinXP and the Ubuntu installation seems to be on the disks but the pc is just not booting. I suppose the problem is with the raid configuration that is not handled properly during the installation, but is there anything that I can do now, apart from reinstalling Windows Xp or installing Ubuntu in a non raid configuration?

View 9 Replies View Related

OpenSUSE Install :: Another Dual-boot \ Drives 1 And 2 Are Striped Together?

Feb 16, 2011

I have 3 separate hard drives. Drives 1 and 2 are striped together and I have openSUSE 11.3 installed. On the third disk I have WindowsXP-64 Professional. I installed SUSE first with the third disk unplugged. I then installed WinXP with the two SUSE disks unplugged. My fdisk -l is:

Disk /dev/sdb: 750.2 GB, 750156374016 bytes
255 heads, 63 sectors/track, 91201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

View 1 Replies View Related

Ubuntu Servers :: Install Boot Loader Into RAID 10 Setup?

Oct 3, 2010

i installed ubuntu server on a 4-hard disk system, i installed with the RAID 10 support that comes with 10.04 server optioon. my raid swap is /dev/md0 and my raid data partition is /dev/md1

hard drives are /dev/sda /dev/sdb /dev/sdc /dev/sdd

the instalation goes fine, from the 8TB im getting 4TB mirrored which is what i want,
but the instalation setup goes up to the point where it asks me to install grub boot loader, There i choose the default option and it does a fatal error.

my main goal is just to make it bootable, any method is welcome. this went beyond my RAID knowledge (more conceptual than technical)

View 2 Replies View Related

Ubuntu :: Unable To Boot Fresh Install On HARDWARE Raid 1

Aug 31, 2010

I am installing Kubuntu AMD64 10.04 on a 500GB Hardware raid1. After the install completes, the computer will try booting, but grub says "No such disk."

The motherboard specs are Here,

I have tried installing to this raid three times, each returning the results mentioned above. Does anyone know what is going on?

View 1 Replies View Related

Ubuntu Installation :: Installing 9.10 On Drives That Used To Be In RAID

Jan 11, 2010

I was recently given two hard drives that were used as a raid (maybe fakeraid) pair in a windows XP system. My plan was to split them up and install one as a second HD in my desktop, and load 9.10 x64 on it, and use the other for mythbuntu 9.10. As has been noted elsewhere, the drives aren't recognized by the 9.10 installer, but removing dmraid gets around this, and installation of both ubuntu and mythbuntu went fine. On both systems after installation however, the systems broke during update, giving an "read-only file system" error and no longer booting.

Running fsck from the live cd gives the error:
fsck: fsck.isw_raid_member: not found
fsck: Error 2 while executing fsck.isw_raid_member for /dev/sdb
and running fsck from 9.04 installed on the other hard drive gives an error like:

The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>

In both cases I setup the drives with the ext4 filesystem. There's probably more that I'm forgetting... it seems likely to me that this problem is due to some lingering issue with the RAID setup they were in. I doubt its a hardware issue since I get the same problem with the different drives in different boxes.

View 5 Replies View Related

Ubuntu Installation :: Creating RAID-1 With Only 2 Drives?

Jun 27, 2010

I have recently installed a Asus M4A77TD Pro system board which supports raid.

I have 2 x 320gb sata drives I would like to setup raid-1 on. so far i have configured the bios to raid-1 for drives, but when installing Ubuntu 10.04 from the cd it detects the raid configuration but fails to format.

When I re-set all bios settings to standard sata drives ubuntu installs and works as normal but i have just 2 x drives without any raid options. I had this working in my previous setup but thats because i had the o/s on a sepreate drive from the raid and was able to do this within Ubuntu.

View 3 Replies View Related

OpenSUSE Install :: 11.2 On Fake Raid 0 Can't Load Boot?

Jun 19, 2010

I installed OpenSuSe 11.2 x64 on my PC.It's not work will:After installation, the system auto login KDE GUI.but when I reboot(or shutdown and open) my computer. Message on screen meaning:"can't find bootable partition".My PC's hardwareMother Board: DFI 790FXB-M3H5(South Bridge: SB750)Hard Disk: WD 500G*2 Raid 0(via SB750 Chip function)Oh, I'm sorry, It's Fakeraid, not hardraid.

View 9 Replies View Related

Ubuntu Servers :: RAID-1 OS Drives - Setting Up A Backup Procedure For The OS Drives

Jan 18, 2010

I'm breaking into the OS drive side with RAID-1 now. I have my server set up with a pair of 80 GB drives, mirrored (RAID-1) and have been testing the fail-over and rebuild process. Works great physically failing out either drive. Great! My next quest is setting up a backup procedure for the OS drives, and I want to know how others are doing this.

Here's what I was thinking, and I'd love some feedback: Fail one of the disks out of the RAID-1, then image it to a file, saved on an external disk, using the dd command (if memory serves, it would be something like "sudo dd if=/dev/sda of=backupfilename.img") Then, re-add the failed disk back into the array. In the event I needed to roll back to one of those snapshots, I would just use the "dd" command to dump the image back on to an appropriate hard disk, boot to it, and rebuild the RAID-1 from that.

Does that sound like a good practice, or is there a better way? A couple notes: I do not have the luxury of a stack of extra disks, so I cannot just do the standard mirror breaks and keep the disks on-hand, and using something like a tape drive is also not an option.

View 4 Replies View Related

OpenSUSE Install :: RAID Driver In Dual Boot System?

Feb 11, 2010

I just installed SUSE 11.2 as dual-boot with WinXP on an older system that has a 160GB PATA drive and a 500GB SATA RAID drive. I left about 80GB on the PATA drive unpartitioned to accommodate SUSE. During the initial installation attempt, SUSE was determined to install on the RAID drive instead of the PATA drive, so I disabled the SATA drivers in the BIOS to force the installation on the PATA drive. This was successful, but now there is no access to the RAID drive from SUSE because there is no driver and it is not mounted. I reactivated the SATA drivers in the BIOS and the RAID drive reappeared in WinXP with everything intact. The SATA drives now appear in SUSE under Hardware Information as "/dev/sdb" and "/dev/sdc" and the listed driver is "sata_sil".

So how do I get the RAID drivers installed in SUSE and then mount the drive so it can be browsed/modified from Dolphin? I would also like to be able to browse/change this drive from other computers on my home network through samba, just like with WinXP.

View 9 Replies View Related

OpenSUSE Install :: Dual Boot Windows 7 / 11.3 Using Separate Hard-drives For Each OS?

Oct 7, 2010

We were trying to install w7 on a reserved partition. W7 did not like the partition (whatever we tried).

Since we had 3 hard-drives, on the allocated drive we deleted all partitions and set the partition table type new to MSDOS (yast etc.....).

W7 installed fine. We did not time it, but it appeared that 11.3 installs faster plus considering 11.3 installs quite a number of applications.

There are plenty of postings re integrating W7 to the Grub-menu.

This system went through several Suse updates, hardware upgrades, basically was all over the place.... we did a "new" install of 11.3 allocating its own hard-drive.

Install......fine, and Grub entered W7 to the menu. Worked ! Mounted the windows partition to /home/yourusername/windows

So, if you really (?) need W7 and have a spare hard-drive, this maybe is a clean solution.

View 7 Replies View Related

Installation :: Hardware RAID 0 Still Show Up As 2 Drives / Cause Of It?

Jul 29, 2010

My two 400G drives which have been added to a single 800G array (per fastbuild bios utility) still show up as two 400G drives in fdisk. Why is that?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved