My Ubuntu laptop's screen goes black in about 10 or 15 minutes. I went into Screen Saver setup screen. Timeout when computer is considered idle there is set to 30 minutes and black screen screen saves is picked.
Why screen goes black after only 10-15 minutes and not 30 minutes?
Seems to happen with every version! I have the same problem as my last thread. Basically it was solved by removing an IPv6 line from the hosts file or adjusting the vnc configuration to use an IP and not host name. Both of these are not working for me on 11.3. I'm not seeing any errors in log/messages. It just sits there with an X cursor that moves around then times out after around a minute or so. I don't know if there are any other logs that will help.
To clarify, starting a vncserver from a terminal will work, but the 'Remote administration' vnc with the login screen will produce a fully black screen with an X cursor that updates with my mouse position.
I'm using natty, and in power management settings the maximum time I can set to put my pc on sleep after being idle is 2 hours, how can I increase this time? I need to put it on at least 4 hours.
View 3 Replies View RelatedI have an Alienware M11x r2 laptop running Windows 7-63 and Ubuntu 10.10 Unity installed.It was all fine and dandy until I changed my grub timeout to 1 sec (or perhaps 0, its been so long i can't remember!) to reduce the waiting time until an OS boots.My grub was set to boot to Windows 7 as default.Now when I boot up I cannot halt the boot process not matter what key I press (e.g SHIFT).I am doomed to forever boot into Windows. Its been months and I had written off my Ubuntu OS but I am tempted to try and fix this one more time.Since I cannot access the Ubuntu installation AT ALL I cant use the usual ways to increase the timeout on the grub menu (yes I have searched the forums far and wide).
Is there ANY way of changing the grub menu parameters without actually booting into Ubuntu Unity? Can I modify the timeout settings using a live cd or usb boot?
I was messing around with the screen orientation and thought it would be funny to orient it sideways. Big mistake The screen went black.I can force a shutdown, login and I get the same black screen. I tried hooking up an external monitor and the monitor showed no input so I'm guessing my laptop doesn't have that capability with Fedora.This is my main computer.
View 14 Replies View RelatedI recently upgraded my graphics card from a Geforce 7600GS to a Gefore 560Ti. And while most things are normal, during boot up my screen isn't "full screen" until X is started, after which everything else is fine. Essentially, all display, the grub menu, the splash screen, console text, etc, is within a box on the screen, with 2" on the left and right, and 1" top and bottom of empty blackness.
From what I understand, this is because the framebuffer is using the wrong resolution, but the maximum resolution that hwinfo --framebuffer returns is 1280x1024 (which I am already using "0x031a".) (My monitors is natively 1920x1080) Is it possible to do something about this? If not increase resolution than at least stretch the screen to full screen?
sudo /usr/sbin/hwinfo --framebuffer
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.459]
Unique ID: rdCR.GGyCBArXznD
Hardware Class: framebuffer
Model: "NVIDIA GF104B Board - 10400050"
[Code]...
I can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedI turned on my Acer laptop and during bootup it seemed normal. After it passed the blue Acer logo, all I could see is a black screen and a black cursor outlined in white in the shape of an X. Thinking it would be a one time thing, I turned it off again.it still was a black screen.
View 14 Replies View RelatedI set the default os to boot as windows 7 with a timeout of 1 second. I thought that this would be enough time to switch os ubuntu when i need to, but I am unable to. How can i reset the timeout to 3 seconds? I also cannot view the ubuntu partition within windows because of ubuntu's file system.
View 9 Replies View RelatedI have clean installed Ubuntu 10.04. After every 10 min. or so of not moving the mouse, I am asked for my password. How can I extend those short min. to say an hour?? Also, at startup I do not have a splash screen only a black screen for about 1min or so. How can I watch the splash screen at startup?
View 7 Replies View RelatedAboard TinyCore 2.7 and opting to run without Xorg. I'm needing either a pointer or syntax example. Seems my monitor supports dpms after executing a quick one-two with:
$ xset s blank
$ xset s 150
Yet I'm unsure how it would look placed in Tinys .xsession:
Code:
Xvesa -br -screen 1024x768x32 -shadow -mouse /dev/input/mice,5 -nolisten tcp -I >/dev/null 2>&1 &
waitforX
"$DESKTOP" 2>/tmp/wm_errors &
export WM_PID=$!
[ -n "$THEME" ] && cp /opt/jwmThemes/"$THEME" .jwmrc-theme
if [ -n "$BACKGROUND" ]; then
setbackground image /opt/backgrounds/"$BACKGROUND"
else
[ -x ./.setbackground ] && ./.setbackground
fi
[ "$ICONS" == "wbar" ] && /usr/bin/wbar.sh
[ -x ./.mouse_config ] && ./.mouse_config &
[ $(which flit) ] && flit &
[ $(which watcher) ] && watcher -g +0-0 &
I can't increase my screen resolution to higher than 800x600. In Windows I have a 1024x768 resolution. This is my xorg.conf file
Code:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[code]....
I have recently installed Ubuntu 10.04 beta version. After installation, my laptops screen resolution cant be increased to 1024x768. More over i cant see that 1024x768 option in the System>Prefrences>monitor option.
View 4 Replies View RelatedI have been arguing with my acer aspire one laptop since I bought it in terms of the screen resolution and have never been able to solve the problem, although I seem to be getting close. I just updated to 10.04 (the netbook remix).I have been following the instructions for how to fix it here. The result was this:
Code:
liz@Pippin:~$ cvt 1366 768
# 1368x768 59.88 Hz (CVT) hsync: 47.79 kHz; pclk: 85.25 MHz
[code]....
Alright guys. I need to find a way to enable a black screen screensaver (or turn off the monitor, or something to avoid burn in) while the machine is sitting at the login screen and completely turn off the ability for the computer to sleep. how I can accomplish that?
View 1 Replies View RelatedI have recently installed 11.04 natty on Intel Core i3-2100 3.1 GHZ using its own graphic accelerator. When the screen is idle for a long time, more than 1 hour, I get a black screen with the mouse arrow but nothing else. the mouse moves the cursor and Ctl+Alt+F1 does work. How to fix this problem?
View 4 Replies View RelatedI installed Ubuntu 11.04 today as the main OS on my laptop.I had deleted my XP partition, and repartitioned it according to a guide I had found. (http:url)......Basically it was setup like this: 500mb ext2 primary partition, has the grub folder, I believe this is either the '/' partition, or the '/boot' partition 2gb swap space logical partition
10gb ext4 logical partition -- this is either the '/' or the '/boot', it contains the 'bin,boot,cdrom,dev' etc folders 243gb (the rest of my hard drive, with the exception of a partition that contains documents and files from my XP OS, formatted to NTFS) ext4, this is the one that has all my desktop/documents/etc folders.After Ubuntu was done installing, I had some message pop up about installing an ATI proprietary driver for my ATI graphics card (an ATI Radeon HD 4330, I believe, I may have messed that number up). I installed it and rebooted, no problem.
Next, I had another update window pop up with 198 items checked and ready to download and install. I went through all of this, and rebooted, again, no problem.Next thing I did was install some apps that were essential for me to have to use for my work (an ide, chat programs, etc). No problem with any of that.Last thing to install was the OSE Virtualbox, and then I installed WindowsXP Pro and Windows Vista Business, then installed the guest addition addon for VB. This all worked without any issues whatsoever.
Time goes on, and I notice my computer is heating up much more than (seemingly) normal. I begin to wonder if its my graphics card. So I shut down the computer and let it cool down. Reboot, and no problem, still working fine.Then I opened a couple of apps and tried a simple game (can't remember the name) I believe it was a simple 3d topdown, as I wanted to test my graphics card. This is where things seemed to start to go wrong. My laptop began hanging, not even allowing me to access the terminal via ctrl+alt+f2. The screen flashed and I saw the blue/green/grey fuzz that I get when the graphics card is starting to heat up too much. Then everything hangs and I can't do anything at all, including move the mouse. I did a hard reboot (I believe this is what you call pulling the plug/pressing the power button, correct me if I'm wrong). I then rebooted, saw a chkdisk, then it booted seemingly normal, but it hung right after the purple screen after the grub screen.
This is pretty much where I'm at right now. I strongly suspect the fault is with the ATI drivers, but have been completely unsuccessful in my attempts to fix it. I've googled just about everything I could think of, along with searching these forums. I've tried just about everything listed in the forums, but to no avail.I've tried the commands that are supposed to purge the ati drivers, but all I get are errors that say they can't remove the 'virtual drivers'.
Right now I'm booting off a live cd, so I know the computer still works fine, just not my actual installed OS. I'd really like to get the issue resolved without having to reinstall, as it took quite awhile just to get it usable in the first place, but this has already taken so much time, I may just resort to that if we can't solve it any other way. Got too much work to catch up on as it is.As a re-instated note, perhaps if you have any tips, but not particularly about fixing the OS, my laptop (I'm strongly guessing my graphics card) is heating up much more than normal, compared to that when XP was installed. Is this more than likely just a driver issue, as is the rest of it? Also, I did have Compiz installed, though I didn't choose for it to be installed, I believe it came pre-installed. I've heard it could cause some issues, though I have no idea as to the validity or relation to this particular issue.
Edit:
I just remembered while searching for a solution, I found a post somewhere that said something about the information not being sent to the monitor from the graphics card properly, thus no desktop. I'm guessing that'd still fall under the driver issues, but again, I'm unsure. I would think that wouldn't be entirely true anyway, since I can still see my mouse fine, just no desktop, only a black screen.
I have Ubuntu 10.04 running kernel .26 installed on my Dell Dimension 2350 with 512mb of memory. The problem I have been having is, When I am using the computer mostly Internet stuff for no reason the monitor will go black then on the screen it will be at a terminal screen, kind of like when you start up the computer, I don't remember what is all on it but the last thing in the list was: checking battery state: OK after that the screen will flash in multiple colors and then it goes into a loop of just black screen than a colorful flash and back over to a black screen. the only way I can fix that is by holding down the power button. this will happen mostly on face-book on the games and just on the profile page, but it does happen just checking my gmail or play solitaire it does this around 4-8 times a day.
View 3 Replies View RelatedI've a problem with my ubuntu 10.04 suddenly when I opened my laptop and after I've entered my password then I redirected to a black screen and then to the same screen again and so on what I can do
View 9 Replies View Relatedout of no where it seems ubuntu no longer wants to cooperate when suspending/hibernating. the screen will just turn to a black screen without shutting down. each time i have to maually power down my laptop.
View 1 Replies View Related'm trying to duel boot windows 7 and ubuntu 11.04 on an Acer Aspire 5736, but when I try to boot from the cd (which I burned with InfraRecorder) it first goes to a black screen with a blinking under score in the corner, then to a purple screen with a couple symbols at the bottom, and then the screen goes black and nothing else ever happens
View 4 Replies View RelatedAfter succesfully installing Ubuntu 10.4 x32 and rebooting pc hangs on black screen with a flashing white dot in the top left corner of my screen, i've tried installing it twice with the same results.
my setup is: Asus p5q-e,
4 gig of corsair dual ram,
ati 4850 graphics,
onboard audio.
ahci mode
win 7 installed on intel ssd, and xp on a samsung 320 gb sata 2,
i had this configuration running fine for 2 months without boot loaders,
on pc start up i choose from which hdd to boot from.
i installed ubuntu on the samsung drive where it was recognised fine, wiped it all and installed automatically.
pls let me know if there is anything i missed, and advice if possible in what to do.
thanks
kannanni
I'm trying to test out using xubuntu 10.04 on my one computer and keep getting a black/blank screen after selecting the 'try' menu option.Is there a way to fix this?I have tried some of settings via F6 with no luck.
FYI -The CD works fine as I have tested it on other machines.The version I am trying is xubuntu x86 (although I have tried ubuntu 10.04 x86 with similar results).I can Alt+Ctrl+F1 fine and get to the cmd prompt
I am using a 15" CRT Samsung monitor and when I upgraded 10.10, the screen resolution became 800x600 and I am not able to increase the resolution of it. This was working fine with 10.04 version.
Below is the o/p for "xrandr":
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 800 x 600, current 800 x 600, maximum 800 x 600
default connected 800x600+0+0 0mm x 0mm
800x600 0.0*
I also see a continuous message box at the top left corner of my monitor with text as "Unknown".
This obnoxious bar has just appeared in Smplayer at the top of the screen. It stays there even when I go full screen. Now full screen isn't full screen and there are black edges on both sides of the screen. I have not be able to figure out how to hide it. I do not need or want this onscreen display. How can I configure Smplayer to make this go away? How can I get my 16:9 full screen aspect ratio back? I have done nothing to mplayer or smplayer as far as editing any or changing any configuration files. I tried several videos and it displays on all of them. It was not there last time I used Smplayer.
View 9 Replies View RelatedI recently installed 11.2 and am now trying to increase the maximum screen resolution.When I go to 'confifure desktop' > 'display' it will not let me increase the maxiumum screen resolution past 800X600.My nVidia 6150 LE drivers/kernal are installed, so I'm not sure quite what to do.
View 7 Replies View RelatedI have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
View 1 Replies View RelatedI downloaded Fedora-14-i686-Live-Desktop.iso and used the Fedora liveusb-creator to put this on a 2GB USB stick. Everything seemed to have gone well and it said complete; however, when I try to boot from the USB stick, I get a black screen with a linux copyright notice at the top and it just stays at that screen forever. I tried this on two computers with the same results.
I'd previously tried with Ubuntu and had a similar issue, it would go to a purple (if I remember correctly) Ubuntu screen and it sat that forever.
OpenSuse 11.3 with nVidia drivers.I have the screen working fine though it only runs in 1600x1200@75 using the nVidia driver (GTX260 card).When I play a game in full screen mode all seems OK but when I exit the game then I just get the mouse pointer on a black screen.There must be something present since the cursor changes as I move it, normal pointer -> hand over a link etc. It's just that black on black isn't very readable.
View 5 Replies View Relatedi am fairly new to Ubuntu. i was using it fine for a month, but today, when i booted my computer up, it came up with a black screen instead of the normal purple ubuntu screen. the black screen had white text on it, and asked for my username and password. from there, it was a terminal prompt. i have been google searching for a while, and have tried typing "startx", "sudo apt-get install ubuntu-desktop", "sudo gdm", and i have also tryed uninstalling xorg, and reinstalling, and none of these things wanted to do anything for me.
View 4 Replies View Related