I can't increase my screen resolution to higher than 800x600. In Windows I have a 1024x768 resolution. This is my xorg.conf file
Code:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[code]....
I have been arguing with my acer aspire one laptop since I bought it in terms of the screen resolution and have never been able to solve the problem, although I seem to be getting close. I just updated to 10.04 (the netbook remix).I have been following the instructions for how to fix it here. The result was this:
Code:
liz@Pippin:~$ cvt 1366 768
# 1368x768 59.88 Hz (CVT) hsync: 47.79 kHz; pclk: 85.25 MHz
[code]....
I am using a 15" CRT Samsung monitor and when I upgraded 10.10, the screen resolution became 800x600 and I am not able to increase the resolution of it. This was working fine with 10.04 version.
Below is the o/p for "xrandr":
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 800 x 600, current 800 x 600, maximum 800 x 600
default connected 800x600+0+0 0mm x 0mm
800x600 0.0*
I also see a continuous message box at the top left corner of my monitor with text as "Unknown".
I recently upgraded my graphics card from a Geforce 7600GS to a Gefore 560Ti. And while most things are normal, during boot up my screen isn't "full screen" until X is started, after which everything else is fine. Essentially, all display, the grub menu, the splash screen, console text, etc, is within a box on the screen, with 2" on the left and right, and 1" top and bottom of empty blackness.
From what I understand, this is because the framebuffer is using the wrong resolution, but the maximum resolution that hwinfo --framebuffer returns is 1280x1024 (which I am already using "0x031a".) (My monitors is natively 1920x1080) Is it possible to do something about this? If not increase resolution than at least stretch the screen to full screen?
sudo /usr/sbin/hwinfo --framebuffer
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.459]
Unique ID: rdCR.GGyCBArXznD
Hardware Class: framebuffer
Model: "NVIDIA GF104B Board - 10400050"
[Code]...
I have recently installed Ubuntu 10.04 beta version. After installation, my laptops screen resolution cant be increased to 1024x768. More over i cant see that 1024x768 option in the System>Prefrences>monitor option.
View 4 Replies View RelatedI recently installed 11.2 and am now trying to increase the maximum screen resolution.When I go to 'confifure desktop' > 'display' it will not let me increase the maxiumum screen resolution past 800X600.My nVidia 6150 LE drivers/kernal are installed, so I'm not sure quite what to do.
View 7 Replies View RelatedHow can I increase the resolutions of my VGA Port?As you can see in the screenshot, the maximum resolution that Ubuntu 10.04 detect it's 1360x768 but in other OS I can use 1920x1080 for example.
View 4 Replies View RelatedI have an EeePC 1005HA with Intel 945G chipset and graphics. I've got a 21" no-name touchscreen attached to the laptop with the intention of hiding the laptop away behind it and simply using the tactile widescreen with virtual keyboard (onboard). By the way, the Touch screen is working great OOTB in Ub 11.04, although will have to tweak some more to get multi-touch working.On it's own the netbook runs 1024x600 (16:9) automatically. As soon as I plug in the larger monitor and mirror the images it auto-defaults both to 800x600 60hz and I have no options to select a higher res. I want to be able to run the large screen in something like 1024x600 or better, as long as its 16:9. At the moment everything is stretched out on the larger screen and on the netbook I have a 800x600 with black margins left & right.
Can't seem to work it out. The Monitor Config doesn't give me any higher options than 800x600 when mirrored. Below is the output of xrandr, if it's any help. Also my xorg.conf file is practically empty.
I have a centos 5.5 server, without a monitor connected to it.Sometime i need to connect to it with VNC, but maximum resolution is 800x600.How can i increase it at least 1024x748 ??I tried in system-config-display changing the monitor to a generic CRT 1024x768, and rebooted.But only allowed resolutions are 800x600 and 640x480.
View 6 Replies View Relatedis it possible to increase the resolution on gtk themes to get rid of visible pixels? Or is there a set limit?
View 1 Replies View RelatedI have an AMD Radeon HD 6950 and I know that no driver will be released for a while that works (current one causes xorg to crash and creates a reboot loop). Until then I have a 1920x1080 monitor running at 1280x1024 bc there are no higher settings.Is there any way to increase the resolution until the driver support comes? I tried a method involving xandr but that didnt work.
View 5 Replies View RelatedI'm having problems adjusting my screen resolution. I'm using Nvidia Geforce FX5300 video card and Samsung T220P LCD screen with resolution of 1920x1200. After installing the Nvidia driver I went to system -> preferences -> display in order to change the resolution to 1920x1200. Unfortunately, the available resolutions were only 640x480 and 320x240. I tried to set the resolution manually, using the advanced button, but when I did this everything was extremely big on my screen.
View 1 Replies View RelatedI have my Xubuntu box connected to a 1920x1200 LCD monitor via a KVM switch. If the KVM is set to the Xubuntu box when I boot, all's well, but if the KVM is set to the other machine, Xubuntu boots into a 800x600 resolution. This behavior started with Maverick, when I was running Lucid. the correct resolution was set no matter the position of the KVM switch. Is there some place in Maverick that I need to set the resolution to 1920x1200 so it is set correctly regardless of the KVM?
View 1 Replies View RelatedI know this is probably a stupid question , but I started using Ubuntu 11.04 .
My screen resolution on windows was 1600x900
But on ubuntu (even after installing proprietary drivers) the highest I can get is 1024x768 .
I tried using xandr but couldn't work it out .
My xandr info
When i tried adding a new mode using the command
I got the following error
Now I'm not sure what VGA refers to , but Im using a vga port to connect my monitor
Also I'm using only one monitor.
Ive just installed Fedora 12, max resolution option is 800*600 can someone advise how i can adjust or improve the resolution to at least 1200*700?Hardware: HP D330m, 2.8GHZ, 700MB RAM, VGA is a Intel Extreme Graphics Display.
View 6 Replies View RelatedI was wanting to use StartUp-Manager to increase the resolution of the GRUB menu and the boot logo screen. Changing the resolution for the GRUB menu works fine. But the Ubuntu logo that should show up during the boot process is all scrambled across the screen. I tried multiple resolutions to fix it and none of them work. How do I restore everything back to their defaults? I tried putting the numbers all back to where they where when I first ran StartUp-Manager but that didn't fix it.
View 4 Replies View RelatedDoes anyone know where to manually set screen resolution in the new 10.4 beta? Used to be in xorg.conf, but it appears that it doesn't exist in this release.
View 2 Replies View RelatedMy screen resolution keeps reverting back to the default resolution 800x600. I'm using ubuntu 10.04, but had the same problem on 9.10 on my Acer Revo r3600 ION. I am able to change the resolution to 1280x1024 but have to do it by the nVidia configuration tool. The tool then allows me to 'Save to X Configuration'which it appears to have done successfully.See the sections from my 'etcx11xorg.conf' file. This is the state of the file after a reboot by the way.how I can get my desired resolution to persist after I reboot?
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Samsung SyncMaster"
HorizSync 30.0 - 81.0
VertRefresh 56.0 - 75.0
Option "DPMS"
EndSection
After update from 8.10 to 9.10 I have screen resolution 1440x900, which is not supported by my monitor. Following changes had no effect on my screen resolution
xrandr:
Code:
$XAUTORITY=/home/zuker/.Xauthority DISPLAY=:0.0 xrandr --output default --mode 1024x768
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
xorg.conf
Code:
Section "Screen" ...
Subsection "Display"
Depth 24
Modes "1024x768"
Virtual "1024 768"
EndSubSection
I installed 10.04 on my former windows box last night, and I seem to be stuck at a screen resolution of 1024x768. I have a Geforce 7600 GT graphics card, and I installed current drivers via the hardware drivers option. I can't go above this resolution in the nvidia x-server settings, and even xrandr says the highest resolution I can use is 1024x768. What is up with that, and how can I change it?
View 1 Replies View RelatedI have tried EVERY solution that has been posted. the nVidia forumswon help. Every solution that involves editing the .conf file crash my system. I wanna have real resolution for my monitor not be stuck at this 800x600 bull$#!tnVidia Graphics CardPlanar PL1700 Monitor
View 1 Replies View RelatedI recently installed Ubuntu 10.04 in my computer, I ran update manager and installed all the actualization but and I can not set the screen resolution higher than 800x600; I have windows XP installed in another partition and the screen resolution can get to 1028x1024 at 85 hz. I have a Pentium 4, 2.20 ghz, 1gb ram, and the video card is a SiS (Silicone Integrated Systems) 300/305/630/540/730 32 Mb.
View 4 Replies View RelatedI'm trying to change the output resolution of a HTPC that's connected to a 720p plasma from (an auto set) 1024x768 to 1280x720 so that the output is the correct 16:9 ratio for the plasma.The HTPC is running Ubuntu 11.04 with a GeForce 7600GT and is connected via VGA cable to the plasma. The plasma automatically detects the PC input as XGA.
The worst effect of this is 16:9 media (video clips etc) looks really stretched out with the letterbox bars on the top and bottom and icons in general don't look square.Nvidia driver has been activated via Additional Drivers but the message reads;
Quote:
The driver is active but not in use"
Any ideas what that means? Should I be looking for a way to disable whatever the Ubuntu driver is so the proprietry one is in use?Under nVidia Xserver settings I don't have an option for a 1280x720 resolution, the next closest resolution for 16:9 is 1360x768 but then portions of the output are no longer visible on the plasma.Could it be as simple as using the DVI output (not the VGA) from the graphics card to the plasma to get a correct reading of the input. Still, I wouldn't have a setting for 1280x720
After upgrading to 11.04, my screen resolution was reset to 1024x768. As the native resolution for my monitor is 1920x1080, I went to reset that. The resolution didn't exist in the Monitors applications, so I did the following:
Code:
kane@Griffin:~$ cvt 1920 1080 60
# 1920x1080 59.96 Hz (CVT 2.07M9) hsync: 67.16 kHz; pclk: 173.00 MHz
Modeline "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync
[Code].....
The monitor adjust, but most of the screen shows tearing and doesn't update correctly. Hard to explain, so I attached a screenshot at 1024x768, working normally, and 1920x1080, fubar. I've cropped these images to get them to fit the forum limitations, but they still show the issue.
My monitor is an LG Flatron W2253TQ, my graphics card is an ATI Radeon HD 4650, although the manufacturer is Biostar. I'm using the default free drivers.
I know there are many threads on similar issues but I can't find anything that will work. Not sure if I need drivers or what to do - I feel really stupid as I should be able to get this right but I am at a brick wall. Basically I have a 20inch monitor hooked up to the on-board graphics card and cannot get higher resolution than 900 x 600. It should be at 1280 by 1240. This is a brand new install with the latest Ubuntu 10. Under monitor preferences its says 'unknown' for monitor type and I don't have any driver disk for this screen but never needed one previously.
[Code]...
I just changed the desktop on my thinkpad from awesome to i3. And now I have some very strange issues with the screen resolution. Because at home I use this x60 thinkpad on a dockingstation and a 19" display. As long as I used Awesome as my Desktop, the display manager as well as the desktop itself could handle the different screen resolution depending on if I'm out with just my 12" on my thinkpad or with the much bigger screen on my home 19" display.
I can understand that i3 maybe cannot handle this alone and I need xrandx to enforce the screen resolution. But why is the display manager (lightdm) also affected by this change? What is so different that even the DM cannot find the proper screen resolution?
I'm running debian lenny and want to change the screen resolution from 640x480 to 1024x768. I'm using a nVidia Geforce FX 5800 and I installed the additional nvidia drivers with the help of this tutorial [URL]. Here is my xorg.conf
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "de"
Option "XkbVariant" "nodeadkeys"
EndSection .....
When I try to change the screen resolution via the gnome menu I just can choose the 640x480 resolution and 50Hz refresh rate.
I've googled the issue and had a little luck, though I can't seem to change my xorg.conf file because permissions are defailed. This is the example xorg.conf file I wrote based upon my original and the modifications:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[Code].....
Just got an HP dv6-2150 laptop. Dual boot with Windows 7 and 9.04 (9.10 will not work but that's a different story). The screen resolution is too low and is set at the highest option available (1024x768 which is a 4:3 aspect ratio). The HP uses the new Intel i3-330m chipset with on-board Intel HD graphics. The system is capable of 1366x768 resolution (16:9) - so how do I get it there? xorg.conf looks real generic - nothing specific to Intel.
View 7 Replies View RelatedSince I upgraded to 9.04 a while back I have had this annoying screen resolution issue. Every time I log into my Ubuntu system the screen resolution defaults to 1280x1024. My preferred desktop resolution is normally set at 1680x1050. So each time I log in I have to open the Nvidia control panel and manually set the screen resolution to 1680x1050. Even after logging out it will still go right back to 1280x1024 when I log back in.
But the funny this is I am almost positive the login screen resolution is 1680x1050 because the picture is crisp unlike the blurry and distorted picture at 1028x1024. I have tried everything from manually editing the x.org conf file to running the Nvidia control panel as root. Nothing saves my preferred resolution of 1680x1050. My Nvidia driver is version 190.42 and Ubuntu version is 9.04. The monitor is an ASUS VW192T+ which is detected by the Nvidia driver.