so when ppl bring me their computer and i install them ubuntu in my monitor when they take their computer to their home ubuntu does not keep the screen resolution i set for them.
View 4 RepliesI have a old Pentium III box with equally old monitor (It says LG Sutdioworks 45v).I have installed Ubuntu 10.04 LTS.I have found it difficult to setup my screen resolution. It shows by default 800x600.After some tweaking I can stretch upto 832x624.I have seen resolution up to 1024x768 in windows on the same box and same monitor.How can I improve the resolution?I have searched and found out that i need a xorg.conf setup as Ubuntu cant identify my monitor properly.I also installed ddcprobe, read-edid.However I have met with limited success.
View 3 Replies View RelatedI cannot get the monitor screen resolution to anything but 1920 x 1440 (4:3).
View 1 Replies View RelatedI changed may graphic card, earlier I used NVIDIA FX5500 with nvidia driver, now I was trying to use ATI Radeon 7500, but there are problems with graphic configuration. At first attempt server started but after I changed a screen resolution the monitor went blank. I restarted a computer but after the X server started immediately the monitor wnet blank. I found that for completely for me unknown reasons Xorg was trying to use an NVIDIA glx module with radeon driver. I removed this nvidia driver, I expected ubuntu would be able automatically to set up a proper configuration, but instead of ubuntu complained about a missing driver. I also tried manually to set up some basic config using Xorg -configure but after that the Xorg server was stuck.
View 10 Replies View RelatedI installed FC11 on my laptop T43 and the video card is ATI Mobility Radeon x300. Now I have a problem of screen resolution with external monitor:
When I do presentation, I have to mirror the two monitors and both set to 1024*768, which is not perfect.
I remember that when I use RHEL 5 desktop edition, The system can automatically detect the external monitor and set it by itself ----- The laptop uses 1400*1050 and the external monitors such as projector uses 1024*768. But I haven't found such feature on FC11.
I need to know how to change resolution on the screen and monitor
View 5 Replies View RelatedI am running Ubuntu 9.10 on a new HP PC (Pavilion p6240f PC).This came with an Intel GMX X4500 Integrated graphics.My monitor is Samsung SyncMaster 2333. Initially I got a very bad resolution, Later I edited /etc/X11/xorg.conf (created the file) and added the following.
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 30 - 75
VertRefresh56 - 61
EndSection
[code]....
With both 1600 x 1200 and 1680 x 1080 I get the resolution but I see lots of shadowing.(The letters are not crisp) Do I need to upgrade any driver ?
~$ lspci | grep -i vga
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
I have a dell studio hybrid PC which I am hooking up to my TCL brand 40" LCD TV to use as a media center pc. The problem I am having is that I can't get the TV's native 1920x1080 resolution to display properly. The rendered desktop doesn't quite fit in the screen (I think its the top and bottom edges that are cut off) so for example the menu bar at the top is completely off the screen.
1680x1050 works fine in the sense that it fits the full desktop to the screen size, but its not the native res. In the resolution changer utility, it recognizes that my TV is a TCL brand but mentions 36 in the model name (the TV I have has 40 in the model name to denote 40") so I think Ubuntu is recognizing the wrong size TV. How can I finagle the screen settings to make the 1920x1080 fit properly on my monitor? Or get Ubuntu to correctly recognize my TV? My TV is a no-name brand so its hard to find info on it or others setting up linux with it.
I am new to Linux (Ubuntu 10.4 LTS on a Thinkpad T40), now just two days, and had everything working nicely. But since I wanted a better higher resolution I tried to set the monitor resolution to a higher value. After selecting a higher resolution first the screen went black and now it has a white background and is steady but has flickering areas. The system is still working. How can I go back to the resolution that was working?
View 2 Replies View RelatedOS: Fedora 12
Video card: ATI Radeon 9200 series
Monitor: ViewSonic 19"
I installed Fedora 12 configured Gnome automatically. Generally default settings. My monitor was connected directly to the video card and all was good. My video card was detected and my monitor was detected as ViewSonic Corporation 19" and I can set the screen resolution to 1280x1024. I had no xorg.conf file, as it seems that Fedora 12 does a great job of PnP to just set everything up.Now I go and complicate things by hooking up my monitor through a KVM switch. All of a sudden my monitor is "Unknown" and the best resolution I can achieve is 800x600.
Sure, I could go and reconnect without the KVM, but I want to be able use it.Is it possible to edit xorg.conf to tell it "Trust me, just use 1280x1024 at 60Hz even though you can't figure out what the monitor is"?
I tried a number of the posted suggestions to generate xorg.conf files but none of them get me what I need. A simple sample file listing that does the minimum is greatly appreciated (I can experiment from there once I get a basic setup working).And can someone explain if it is X or the ATI driver that is getting confused by the unknown monitor type. It helps to know what is actually going on in addition to a fix (so I can figure it out myself in the future). Thanks!
on a 6-7 years old compaq laptop, connected to a brand new hp monitor i am having a mismatch with computer/monitor resolution.
before i had ubuntu 10.04 which could only run in x's safe graphics mode - allowing for full screen resolution but with handicapped graphics - for example videos fullscreen would be quirky and run with cpu at 100%, something which was no problem before 10.04.
then i tried ubuntu 10.10 and later lubuntu 10.10 (which had exactly the same problem); the monitor is running 1440x900 while the computer is rendering to only 1024x768 - leaving a huge black border on right and bottom of screen. the gfx is still crippled; videos fullscreen is quirky as before.
I recently purchased a cheap computer to use for everyday tasks. It came pre-loaded with Windows 7. The monitor I am using is a Vizio VX20L. It's native resolution is 1366X768. I have no problem with the screen resolution in Windows 7 but in Ubuntu, I am having some issues. I have the propriatary Nvidia driver installed in Ubuntu but for some reason I cannot get the screen resolution right. I am currently using a resolution of 1360x768 and the right part of my desktop is not on the screen.
I have tried to adjust the screen size using the monitor settings, but I still cannot get the whole screen to show up. If I set the resolution to Auto in the NVIDIA X Server Settings, it defaults to 1280X1024 and I can see my whole desktop, but it is streeeeetched. Here is some relevant information pertaining to my system:
I'm using Ubuntu 10.04
Integrated Video chip is NVIDIA GeForce 6150SE
The driver I'm using is NVIDIA accelerated graphic driver (version current)[Recommended]
screen is a Vizio VX20LHD
I have Ubuntu (running Jolicloud) on my HP dv2000 laptop, connected to my Sony AV Receiver through HDMI to use the TV as an external monitor. However, the resolution seems to be slightly off as the outer edges of the screen are cut off. Is there a way to fix this by editing the xorg.conf file? My current setup is below. I tried adding the line "Virtual 1244 700" to the subsection "display", but when I restarted it threw me into low graphics mode. Is there anything else I can try?
I also tried setting up the resolution at 1920x1080 on the TV and kept the default resolution on the monitor as 1280x800, and as you would expect displays the entire desktop in a smaller version on part of the tv. However, the desktop is still offset, leaving the top and left margins cut off. So, perhaps I need a way to offset the screen? Is this possible in xorg.conf?
A few minutes ago, I was connected to my remote machine running Ubuntu 10.10. I changed the resolution of the screen while connected with VNC, but now I can't connect to the remote machine. How can I fix this without leaving my house?
View 2 Replies View Relatedso here's the deal. A few minutes ago, I was connected to my remote machine running Ubuntu 10.10. I changed the resolution of the screen while connected with VNC, but now I can't connect to the remote machine.
View 10 Replies View RelatedOk, so here's the deal. A few minutes ago, I was connected to my remote machine running Ubuntu 10.10. I changed the resolution of the screen while connected with VNC, but now I can't connect to the remote machine.
How can I fix this without leaving my house?
First off, let me say: I'm a long time Linux hobbyist and recently installed Fedora 12. I've been looking (some say "lurking") around these forums for a bit after I loaded it up and let me say: Leigh, You're an amazing young man! Keep up the great work! I've a question: I've just put together a hobby computer: Pentuim 4, with 1 Gig of RAM and a Nvidia Geforce5700LE. When I install Fedora from a fresh install, everything works great: nice screen resolution, good graphics, etc. but no 3d or acceleration, so I'm very limited on my programs.
So I decided I need to upgrade my Nvidia driver. I followed Leigh's Nvidia setup guide after installing Fedora 12 (all four steps!) everything seemed to go fine, but when I reboot, I quickly see the Nvidia splash screen, but the screen then goes blank. Well, not really blank, I can see what appears to be a kind of cross-hatch pattern, plus I can see what should be my mouse cursor on screen (it also is a square shaped pattern). I suspect it may be at a screen resolution that my monitor doesn't support. Once there, the computer pretty much doesn't do anything else. Usually I can break into the x driver loading and go to the command prompt, but this latest time I can't even do that.
I have a mac book pro 5,3 with the nvidia gforce 9600m. After getting Ubuntu installed as a dual boot, I wish to use an external monitor while using Ubuntu. (it doesn't have the problem with OS-X) The external monitor is a samsung syncmaster 192 n. when I connect the other monitor and press 'detect display' both go grey creens(the external already is of course). My lapton screen will not recover until restart either. I need this monitor to run a numerical mesh 3d mesh creator that will not fit on my screen alone. Wouldnt be a problem if the creators were software engineers but the program window cannot rescale, and is beyond the resolution capabilities of my 15'' screen alone.
View 1 Replies View RelatedI've installed Ubuntu 10.10 on my Macbook Pro 5,5. Everything is running fine with some tweaks. Just one thing bothers me: when I tell Nvidia X Server Settings that I want to use my external screen as primary screen it doesn't put the gnome panels to the other screen, well... sometimes it does after a couple times but most of the time it doesn't.is there a way to automatically detect when I connect a monitor instead of going to the Nvidia settings? Just the way Mac OS X does?
View 1 Replies View RelatedI'm playing with dual monitors. I have an NVIDIA GT220 set up so that my monitor and my TV are running as extended desktops. Everything is working well enough, but there is one annoying bit I've noticed:
If I'm watching ..... on monitor 1 in fullscreen and working on monitor 2, clicking anything in monitor 2 kills full-screen in monitor 1. Is this something that can be fixed somehow or is it a hardwired "feature"?
I am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again.
When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have a Thinkpad E420, Fedora 15
I am having problems with the refresh rate if the screen. In the refresh mode of the monitor in the monitor options have only one option 60Hz. I have LG 24 + ATI Radon 3870, and have already installed the ATI driver via Ubuntu download center.
View 1 Replies View RelatedHow to change the resolution of my tv to be the same as the monitors. I mean cloning ..
View 9 Replies View Relatedjust installed ubuntu10.04 has set monitor resolution to 800x600 i need 1920x1080 i have been at this for two days now and getting absolutely no where , i could set this on windows in 5 minutes , why does it need to be so hard on ubuntu, i really prefer ubuntu to windows but problems like this really can drive one to despair. i have tried so many different web sites and follow instructions but keep getting command not found which i dont understand why. here is an example of something i tried in terminal xrandr --output VGA --mode 1920�1080 --rate 50 i get warning: output VGA not found; ignoring.many other things i have tried come up with command not found .
View 4 Replies View RelatedI have a laptop with an "ATI Technologies Inc Mobility Radeon HD 3400 Series" video device. I have trouble configuring the second VGA monitor attached to the laptop to 1024x768 resolution. It is always stuck on 2560x800. My xorg.conf file is as follows:
Code:
Section "ServerLayout"
Identifier "amdcccle Layout"
Screen 0 "amdcccle-Screen[1]-0" 0 0
Option "DefaultServerLayout" "dualscreen"
EndSection
[Code]...
Just installed 11.04 on a box that it is on a kvm switch. As long as the switch is connecting the monitor to the booting Ubuntu box, the resolution of the monitor is detected OK. However, if for some reason I am working on a different box and the KVM switch is routing K V and M inputs to the other box, then Ubuntu defaults to what seems a botched VGA setting (i.e. it chops off top and left sections of the display).While in this "VGA" mode if I log out and log in, it re-detects the resolution ok.Is there any way to force Ubuntu to use a specific resolution no matter what? In this way, if I am working on a different box while waiting for Ubuntu to load, when I switch the resolution will be OK.I tried the only thing I can think of and this is to set the "good" resolution as "default" for "all" monitors, but it has no effect.
View 2 Replies View RelatedI was playing around with the NVidia settings control panel today and I saw that its Resolution dropdown was giving me options for
1680*1050
1920*1080
My monitor supports up to 1440*900. When I selected one of the higher resolutions, it didn't look very sharp, and the text was somewhat fuzzy and lacked clarity. Was this rendering being done by the graphics card but 'compressed' by the monitor?
The status said 'switched to metamode'. I tried searching but found nothing - what exactly does MetaMode mean? I'm more interested in understanding what was happening, only experimenting with the higher resolutions. What monitor and resolution do you have?
why both ubuntu and centos 5.4 will only give me 800x600 resolution on my monitor when opensolaris immediately gives me 1280x1024?The first time I tried ubuntu it gave me 1280x1024 and now will only make 800x600...This is a viewsonic VG930M Monitor..
View 4 Replies View RelatedI simply ran the Guest Additions CD (on VirtualBox), double clicked the x86 (I'm running 32-bit) executable, and got that error.
View 6 Replies View RelatedI have an asus eee pc with a 7 inch screen. the screen is small and today I attached a 15 inch dell monitor to increase the screen size. the dell monitor is displaying a 720x 400 resolution which results in a very large screen but no more space on the screen. I can select 1024x768 resolution in system,preferences, display. HOWEVER I cannot select APPLY to this resolution because the apply button is not visable on the bottom of the screen because the display is SOOOO big.
View 4 Replies View Related