My PC has 2 systems, Windows & Ubuntu. Windows can detect my wireless network but Ubuntu can't. The Network Manager does not show any wireless network. How do I fix this problem? I'm still not very good with the Linux system but I keep trying.
View 6 RepliesI am using Ubuntu 10.04 and it doesn't detect my wireless card. Its an AirPlus GDWL G510.
View 1 Replies View RelatedAs an introduction to the problem I'm having: For a long time, I've been on 9.04 and my wireless worked quite happily. Then when I upgraded to 9.10, to my despair I found that my laptop no longer detects my wireless driver! Before I go on, I should also say I'm rather inexperienced with Ubuntu in general, despite having used it for quite some time.
Anyway, onto the informational part: I'm using a Compaq Presario CQ40. According to lspci, my wireless network card details are as follows:
Code:
03:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
lsusb shows the following:
Code:
Bus 003 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
[Code].....
I have Slackware(x32) 13.1 installed on my computer. Everything runs just fine except it doesn't seem my wireless card.I looked around and found a driver on the Realtek website. But, after I installed it, linux wouldn't boot. It would just hang. The driver did help my get the card detected, though.
On lspci, I found:
02:00.0 [Realtek company name here] RTL8101E/RTL8102E
03:00.0 [Realtek company name here] Device 8172
On windows, it said I had RTL8191SE. I am confused as to which card I have and which driver I need.I reinstalled the driver and rebooted. I then turned off my ether card via bios. Then I rebooted. Linux then booted just perfectly. However, I couldn't get the wireless to work. I was freaking and then left to go do something else with my hands. Then I realized I had the card turned off.
I mentally punched myself. >.>
I recently acquired an HP2133 netbook. It comes with SUSE 10 enterprise desktop pre-installed. WI-FI was working fine, though a slight pain for asking for the key every time. I thought I would apply all updates I could find and that may improve my networking.Having applied all I can find the wi-fi is now broken.If I use YaST I can see the Broadcom internal device seems to remain recognised, it even has the configuration I set for my wi-fi network access.The problem seems to be the NetManager applet, which denies all knowledge of wi-fi now and only has wired (which is working).Ironically the update causing the failure was applied wirelessly.I am slightly at a loss how best to proceed - I was going to cut my losses and make another boot partition with Ubuntu, but the live CD I made failed to run so that I could make a flash boot version, I shall have to return to that.
I have also now discovered that SUSE 10 is a bit long in the tooth - I sort of assumed it was current, given I bought the machine recently. So I'm wondering if it would be best to take the hit and reformat completely? I know it is broadcom, so should not be a problem, and I have been through ndiswrapper and the like in the past, though somehow I seem to have forgotten all about it now!I was happy enough with the SUSE setup and this is highly annoying as I was only updating to fix an annoyance and now the wifi has been broken... Perhaps there is an alternative applet to the netmanager that may play with the card and allow me to connect to networks?I look forward to recommendations, at this time my primary objective is to restore wifi functionality, longer term perhaps I need to review distro and installation, but I should like to do that on a dual boot basis I think
When i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies View Relatedmy Sansa Clip+ 4gb mp3 player isn't detected at all in nautilus. my usb memory stick shows up nicely though. i should also mention, this same mp3 player is detected just fine on my work computer (pclinuxos - lxde) - rrrr....
View 8 Replies View RelatedI have all of my music on an SD card so it doesn't take up space on my hard drive. I put it into my SD card reader and ubuntu is all like, "gtfo doesn't exist."
View 2 Replies View Relateduntil recently, my CD/DVD-RW drive(from TsstCorp) on my Hp 530 lappy used work fine. But now, (I dunno why,), the drive is not showing up ANYWHERE... not even in boot menu... The power supply is fine as i can open the drive and can also hear the typical Cd-dvd drive noises after inserting a disc...I am totally lost now and would really appreciate ANY help... again,... the drive is not showing up ANYWHERE... not in any file manager.
thanks in advance for replying and in real time for viewing
i'm italian so, please, be patient if my english isn't perfect I write here because no one of italian Fedora and Ubuntu forums could help me.I've a problem with my dvd writer. I think no linux distro can detect my Dvd Writer, because i tried with Fedora/Ubuntu/OpenSuse/Mandriva/Zenwalk and no one decect it. I must boot distros from liveusb because livecds don't start.
View 7 Replies View RelatedSony DVD RW DRU-840A , wont read any dvd... undetectable by Fedora 12_64 default disk utility..Do i need to install a linux driver?no problem installing fedora using the dvd drive.system spec: asus extreme mother board, core 2 2.6ghz cpu, 8800GTS graphics card, X-fi sound card.
View 2 Replies View RelatedI have just installed Centos 5 on my HP Proliant ML110 G5 Server. At the install time it could not detect my DVD-ROM drive so I installed it using FTP hoping that it will make it work after installation but nope. My system is running but I cannot see ant DVD-ROM drive on my system.
It's really critical, I have lots of software to install from DVDs and actually I am relying on a shared DVD-ROM drive from another machine and it's quite slowing me.
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
I want to try to get wireless access to the wifi router with the xbox360 wireless network adapter.Is this possible?
View 1 Replies View RelatedI am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)
I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.
It is booting much faster now but the wifi keeps dropping off.
Spec:
Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedI have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
I am a Windows refugee who discovered Ubuntu as a way to save my files from my virus-ravaged computer. Had no installation discs for Windows, so when I had to wipe my hard drive and start over, I decided to give Ubuntu a try. I've had mixed success, but that's another post...
Right now, the problem is that I installed 10.10 two weeks ago and was able to connect to the Internet with no problems - until yesterday. Suddenly, our wireless network (the only one in the vicinity) does not come up as available in Network Manager. In fact, the entire wireless option disappeared. I know there are many posts and threads on here about this, but weeding through them trying to find an answer is more frustrating than actually dealing with the problem. I know the router works because I can post on this forum from the Macbook. I really like Ubuntu and would like to keep using it, but not being able to connect to the Internet now on top of the other issues I've had is making me doubt I want to continue down this Linux road.
P.S. When I attempted an analysis through System Testing, it said something about there being no proprietary drivers?
my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
I've installed the Ubuntu 10.04 Server onto a PPC G4 Mac just for the experience of setting up a server. During the installation process Ubuntu couldn't auto-configure my DHCP Network. I'm using the airport card on a wireless network. How can I manually configure the network once Ubuntu is installed.
View 6 Replies View Relatedi looking to replace network manager on my laptop with another wireless program. iv been looking at Swscanner, Rutilt wlan manager, and wicd network manager. iv had trouble with network manager not being able to connect or losing connection fairly easy. im using a gateway m6843 running ubuntu 10.04 32 bit os.
View 2 Replies View Relatedat start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
View 3 Replies View RelatedOn Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies View RelatedI've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
Debian 2.6.32-5-amd64 KDE I have to make one of my computers wireless. i need some product recommendations for a wireless access point & a wireless network card.
View 4 Replies View RelatedI clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
View 2 Replies View RelatedI am having a little trouble connecting to my wireless network. Running Fedora 10 32 bit.I'm trying to connect to a hidden wireless network. I updated the firmware for my driver but apparantly the driver is still not working. Broadcom has a driver from their website for Linux 32 bit systems. Should I attempt to install it? I read a post where the driver is built into the system kernel. If so I would need to blacklist the one of the drivers. Correct?
[justin@justin ~]$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
code....