In System Monitor, under the "System" tab, my Processor and RAM is listed (including specs for each of these), but my Intel graphics card (4500) is not listed at all? I am experiencing some periodic screen flicker - could it be that the video card is not detected?
Screencap of my system monitor [URL]
I have three monitors. Two are hooked up to an ATI card and the third to an nVidia 6800 card. This third monitor is not being recognized. I tried installing nVidia's official Linux drivers but received an error that no compatible device is present. Going into System > Preferences > Display shows only my first two monitors. I'm running Ubuntu 9.10 x64.
View 1 Replies View Relatedsetup the correct mode for my laptop-video card-monitor
Video card - ATI mobility Radeon X1600
External Monitor - Belinea b.display 2 22"
Right now the external monitor is working, but sometimes it goes black for 2-3 seconds and then works again. This happens sometimes 5 times in a row, sometimes once, sometimes none. Other issue, when I install any new kernel it doesn't work. I get weird picture on monitor.
So after I installed the ATI Radeon 3400 series video card in my machine, the Xserver cant start! after it loads, it takes me to the init 3. When I tried startx, the screens either go blank or doesnt let me.
I tried to install everything following this website: [url]
I wanted dual monitors but now I cant even get one. The xwindows doesnt appear.
Things I tried:
1. Deleted the xorg.conf and reconfigured (didnt work).
2. sax2 -r -m 0=versa (didnt work)
3. reconfigured the ATI radeon driver from init 3 (didnt work)
4. copy and paste the oold version of xorg.conf (didnt work)
5. tried to run set apt or dpkg-reconfigure command (commands not found)
6. tried xconfig and prompt the best I coudl (didnt work).
7. aticonfig commands (As shown in website) (also didnt work)
I have the live CD to run it from there but I dont know what to do once I get to the terminal.
Is there any way I can revert to previous configuration since the ATI driver gives me some problems? Like a restore function in windows?
How or what files I should change for the X-server to run properly (is there any other file than xorg.conf?....)
The monitors I have:
2009W Dell Monitor
1398 Dell Monitor (I wan to get the dual exntended monitor but it seems to gave me only the mirror image, thats why I tried to reconfigure the video card)
VideoCard:
ATI HD Radeon Mobile 3400 Series
Computer:
Dell Optiplex 680 (i believe) with SUSE 11.26 and x86_64 bit
Or if you can send me the xorg.conf file ...
openSUSE 11.2 (i586)
VERSION = 11.2
on an IBM x3250
Problem is that after the screen comes up to chose the default version or failsafe, my monitor shows no input. If I delete the VGA 0x031 (i think that's the number) on the Options line in the screen where you chose the version, I get my command line interface.
Can I make the blank VGA options permanent?
I have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
So the only experience I have with Linux is all from Ubuntu, and I just spontaneously decided that I needed a change...two days later my triple boot Macbook Pro got slimmed down to a dual boot OSX/OpenSUSE 11.2 machine. But there are some general problems, and I have absolutely no idea how to solve them. First, wireless isn't recognized at all...there isn't even a space for wireless connections. Second, I haven't been able to get compiz to work yet, and I can only suspect that the system doesn't recognize my video card, or the driver isn't installed. Yet again, no idea how to fix this.
View 9 Replies View RelatedI would like to know if anyone has built a system with a video card that provides a composite video output. Which Linux distro and video card are you using that allows for composite (YES composite) video output from a video card?
I am looking for specific answers here because I don't want to reinvent the wheel if its been done before or waste, money and time.
This is a triple-monitor setup with two video cards, where the mouse pointer gets "stuck" if it tries to cross from one video card to the next one. It worked correctly in openSUSE 11.2 and doesn't work in openSUSE 11.3 with the same xorg.conf. This is a 64-bit openSUSE 11.3 with xorg 7.5-11.3 (the openSUSE prepackaged version). I've already tried NVidia drivers 256.53-16.1 (the openSUSE NVidia repository version) and 260.19.12 (the latest off of the NVidia website).
This is the same xorg.conf that I used successfully in openSUSE 11.2. I tried a new automatically generated xorg.conf using nvidia-settings and it had the same problem. This forum won't let me upload the relevant files, but here: [URL] is a tar-ball with my xorg.conf, Xorg.*.log, /var/log/messages, and the NVidia debugging output.
Phenom 9500+ quad core, 3GB RAM, Nvidia 8800GT: 260.19.36 driver.Installed the latest Boxee for Linux. Got my remote setup. Everything works except when I open a video it opens in a tiny box in the upper left hand corner of my monitor.Is there any way to get Boxee videos to play full-screen?
View 6 Replies View RelatedIf I take out the existing video card and put in another one of a different type (but not a different brand), how does Ubuntu behave? I know what Windows typically does. Windows starts up the screen using a default video driver which is at least 1024 by 768 and then asks you what this new bit of hardware is and asks where the drivers are. I'm pretty sure Ubuntu has default drivers of its own, but I don't know what their resolution is.
View 3 Replies View RelatedI recently bought a video card for my pc. I had it running pretty nicely on Ubuntu10.10, I started windows and later restarted and after that it wouldn't get past the Graphic cards bios. this is rather odd isn't it? I suspect it maybe dead or that my motherboard bios is stuffed but i reset that too and it still wont go.. The specs are Pentium4 Proccesor 1gb ram motherboard 661gx-m7 Nvidia GeForce FX5200 DDr128mb
View 5 Replies View RelatedGot a bit of a problem where xorg can't start kdm. I pulled out a dying AGP card to try and switch to onboard video, and I think the previous configuration is gumming up the works.I've been running this system for quite a while, as you'll be able to tell from the version numbers.Would like to avoid having to transport my Amarok databases to a new server. I make heavy use of the song ratings and whenever I try to transport the database from the old system to a fresh build I have to spend hours relearning sql commands.Any ideas how to either fix the resolutions on the ATI or (preferably) get KDE to start on the onboard graphics?
View 3 Replies View RelatedMy video card developed problems, so I followed the suggestion in this thread:
Quote: Boot into recovery mode, then choose root, for a command prompt and enter
Code: dpkg-reconfigure -phigh xserver-xorg
but my ubuntu 10.04 32-bit system still won't boot. Shortly after the ubuntu logo comes up, before the login, my screen goes black and there is no more video signal. What else can I do to reset the video configuration? The card only has this info on it: I could put the card back in the system, reboot, and then pre-configure the system to drop to the intel 865G on-board video, but the msi card has intermittent problems and will spontaneously re-boot several times during the first ten minutes of turning on the system.
My system: Pentium 4 3.6 GHz, 3 Gb DDR ram, GeForce 210 video card, Ubuntu 10.04.
I have previously used Cinelerra-cv (on Karmic) and recently Openshot (on Lucid) with not much trouble. I have been sampling other video editors (Kdenlive, avidemux, kino etc). Now I have my video card crashing whichever I use, mainly when trying to load clips. I have disabled Compiz, uninstalled all video editors and then reinstalled one at a time. I still get early video crashes whichever I try.
I have persistent video tearing my second monitor (Mitsubushi HDTV). I have tried everything that was suggested with some improvement. I have no issue with tearing if I add the following to my xorg.conf
Quote:
Section "Extensions"
Option "Composite" "Disable"
EndSection
Is it possible to disable composite for one monitor only and keep it for the other. Or at lease is it possible to have compiz for one monitor only and disable it for the other.
I am facing problem with the fresh installation of Fedora 11. (I have moved from Fedora 9). When I try to view videos on ..... or use the Cheese Webcam Booth, I get blurred lines on the screen and I am unable to see any video or pic.
Also I noticed that the when i go to System > Preferences>Display, it shows me UNKOWN MONIOR.
However, if I got to System>Administration>Display and enter the su password, it shows me correct monitor and the graphics driver.
I am not sure if my original is related to the Unknown Monitor.
I also tried to install Nvidia driver but it crashed the xserver and I had remove the driver.
My Monitor is LG 700E and Graphics card is from intel. as I am not able watch any video.
I've been playing around with Damn Small Linux 4.4.10 on my Dell Inspiron 3000 laptop for quite a while now, and this is the first time I've been downright stumped. To make a long story short, I'm trying to play 480p video on a machine with a 233 MHz Pentium processor, 112 MB of ram, and a Neomagic MagicGraph 128XD graphics card (NM2160). Crazy? Maybe, but I don't think so. I'm using MPlayer set to Xv mode with the XFree86 4.3.0 server, and so far, I've been able to get it to play 360p mpegs with minimal stuttering. However, MPlayer crashes with 480p. This is because the 128XD only has 2 MB of memory, which, after the 1024x768x16 screen takes its share, doesn't leave enough room for a 640x480 overlay.
The creators of MPlayer are aware of this limitation, and suggest adding the following line to my XF86Config file: Option "OverlayMem" "829440"
As I understand it, this is supposed to extend the video card's frame buffer into system memory, thus allowing the higher resolution video to play. However, it doesn't work, based on this output from my XFree86 log file: cannot reserve 829440 bytes for overlay...
Some other suspicious-looking lines from the log file:
I've been having issues where I am running out of video memory on my ATI Mobility Radeon 5470 (latest Catalyst), and I would like to be able to examine what is going on with it.How can I monitor my video memory like how I can monitor my CPU and RAM with top or system monitor?
View 2 Replies View RelatedHow can I setup a lan connection using wireless pci card on entire system D-link DWA-510 card I have .
View 5 Replies View RelatedIn System Monitor, on the File Systems tab, the "Total", "Available" and "Used" columns don't seem to add up, and the "Used" percentage doesn't seem correct either.
My config:
/dev/sda1 = 80 GB SSD drive, / partition.
/dev/sdb1 = 50 GB FAT32 partition of an external 500 GB USB hard disk.
/dev/sdb2 = remainder of the 500 GB USB hard disk encrypted using luks.
Screenshot: The /dev/sda1 figures don't really add up well, but they're close at least (how you get "50% Used" from any of those figures I don't know!).
However, for /dev/sdb2, they're miles off:
"Free" = 146.2 GiB
"Total" = 409.7 GiB
"Available" = 125.4 GiB
"Used" = 263.5 GiB
[Code]...
I have 2 video cards installed, and I only have one 22" monitor (1680x1050 pixels).ATI Radeon HD 4290 Nvidia 7300 GT Silent How can I make the both video cards render OpenGL stuff at the same time? Is it even possible?
And which GPU is faster? ATI Radeon HD 4290?
Happens on Jessie AMD64 with mate, I can't go to a tty to kill mate system monitor, mouse stop working, keyboard stop working. I tried changing the theme, and now it freeze opening mate system monitor.
View 0 Replies View Relatedthe only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time.
The exact message is:
The current settings cannot be applied. Possible issues may include:
- Display(s) cannot be enabled.
- Setting(s) cannot be applied due to insufficient video memory.
So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question:
First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment. UPDATE: I got my active adapter in the mail today (it's DisplayPort to DVI) and so far things seem to be better. I can run my third screen, drag things seamlessly between them, and I am also running compiz. The adapter I'm using is a "B087B-005B" made by "Accell", UPC is "826388106239".
There's still a couple "annoyances" that need worked out though: The left most screen is always the primary monitor. Which means the "gnome bar" (is that what you call the applications-places-system menu?) is always on the left most screen. It also means that new dialogue boxes always opened centred on the left screen, which is counter intuitive. Especially if you're using a program like GIMP and the text editor or color picker pops up on the left. Does anyone know of a way to change it so that new windows always pop up on the center screen?
I have recently installed ubuntu using wubi on a dimension 9100 PC.When i boot up ubuntu I get a message that it cannot display current video mode when the GUI tries to launch. The monitor is a Dell E173FPb.From digging about on google it seems I need to edit the xorg.conf file? However, it doesn't exist in the /etc/X11 directory. Does wubi not create this file?
I then created a template of this xorg.conf with the "sudo X -configure" command. I then copied the created file to /etc/X11/xorg.conf and editied the Monitor settings. however, I still get the same error even when I put in the HorizSync and VerRefresh settings shown on the Dell webpage (31-80 and 56-76 respectively).
I have two video outs on my AGP video card. One is VGA and the other is S-video. I tried connecting the second monitor (Viewsonic) by itself to the VGA port and it works fine and runs at 1280x768 very clearly. I then attached the LG monitor instead to the VGA and attached the Viewsonic to the S-video port. Now it is running at 1024x768 and I have no option to increase the resolution.Is this a limitation based on S-video being worse than component, which is worse than VGA and it simply cannot handle the data density for larger resolutions? Or would it be my video adapter? I swear I had monitor control working fine through the panel, but now when I click on the monitor button it says, "It appears that your graphics driver does not support the necessary extensions to use this tool. Do you want to use your graphics driver vendor's tool instead?" and that opens an Nvidia X control panel.
Also, using S-video means the computer doesn't recognize the Viewsonic LCD TV properly, it just recognizes it as a TV. Is this because S-video doesn't play nicely with EDID reporting?It would be nice to get a sharp picture on that TV, the way I had when it was connected like a monitor via VGA. I am not sure what's going on anymore, so any help on clearing up driver issues or getting configuration apps installed or anything like that would be helpful.
I have a dual monitor setup with a nVidia 7300 card. I'm not sure exactly when this started to happen, but it's happened for a couple of years at least. when I'm in one or the other monitor the cursor will sometimes "stick" in that monitor and refuse to go to the other monitor. it'll just 'wrap around' as when I go to the right part of the monitor, it'll then jump to the left side, and vice versa. Also once in awhile, if I'm in one monitor, the cursor will be taken away and put on the other monitor. I'm just now starting to see a few patterns on what's happening. It's worse if I have VCL playing in the left monitor, (my secondary), and I've got a program maximized in the right (primary) monitor. That's when it'll 'stick' on the right monitor. After I roll up the program or minimize it, then it'll free the mouse. But it's not instant. After it's freed, it still doesn't work exactly. If you click on any program on the left monitor, then you have to move back and forth before the mouse will work on the left monitor.
The second problem I'm having happens only on the secondary monitor. At times the precision is WAY off. For example, if I try to put the mouse right on an icon, and click it. It won't work. But if I move the mouse over to the right or left, suddenly the pop-up comment box pops up, the icon is highlighted and clicking will run the program. It can be off as much as 100 pixels! I've seen these problems in all sorts of GUIs; XFCE, DXCE, KDE 3.x (I never tried it in KDE 4.x since it was nearly unusable) and Gnome. Right now I've only see this on Ubuntu 8.04.01, to 9.10 (I never went past 9.10), and at first I thought it was X since all GUIs had problems. But someone now says that nVidia's driver might be to blame. If you can tell me what command to type in at the terminal, I can supply the current video driver's version.
See screenshot attachment. I know there was going to be changes to GNOMES appearance, but I thought it was just moving Close/Maximize/Minimize to the other side. If the screenshot is correct I'll just adapt and move on, if not how do I fix it?
View 5 Replies View RelatedI run a number of Ubuntu 9.10 boxes attached to multiple daisy-chained KVMs. None of the PCs are using any GUIs - they all run in console mode. I often reboot them remotely via an SSH session, etc. If a monitor isn't actually active on the PC when it reboots, Grub2 uses a low-res video mode, despite having a higher-res video mode set correctly in Grub2's configuration. If I reboot WHILE THE MONITOR is attached to the Ubuntu PC via the KVM, the video mode is set correctly as configured in Grub2's config files. If I reboot WITH NO MONITOR attached, the video mode is ignored and I'm stuck in a low-res mode next time I attach to the PC via the KVM. How can I force Grub2 to honor the configured graphics setting, despite not having a monitor present at the time it boots?
View 1 Replies View RelatedI'm using a laptop and running a secondary monitor to my TV. My laptop has ATI HD 3400 video card. The TV has a higher resolution than the laptop's monitor. When the video is full screened on the TV, the actual video uses the resolution of the primary monitor and not the second.
View 2 Replies View Related
